Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹23.9 LAccepted-AOC | L1 | Accepted-AOC LOWEST BIDDER | |
| 2 | L2₹25.6 L+₹1.6 L (6.76%)Rejected-Finance | L2 | Rejected-Finance NOT LOWEST |
Tender Value
₹26.4 L
EMD Value
₹52,720
Closing Date
23 May 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GARRISON ENGINEER ABOHAR
GARRISON ENGINEER ABOHAR PIN 152113
PROVN OF 02 X TOILET AND BATHROOM BLOCK NEAR BLDG NO P-450 AND P-447 AT 67 INF BDE CAMP AND OTHER SANCTIONED WORKS AT MIL STN FAZILKA.
2024_MES_651043_1
TOKEN NO GE ABH-03/24-25
Open Tender
Civil Works
Item Rate
180 days
FAZILKA MIL STN
AS PER NIT
7 documents required · 7 mandatory
₹500
GE ABOHAR
₹52,720
Yes
13 Jan 2025
25 Apr 2024
25 May 2024
25 Apr 2024
23 May 2024
9 May 2024
Amount
Excavating in trenches, n exc 1.5m wide & n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan & n exc 1.5m in depth & getting out in soft/loose soil
Surface excavation n.exc 30cm deep & averaging 15cm deep and getting out in soft / loose soil.
Spreading & levelling in layers n exc. 25 cm thick & well ramming incl. watering as required
Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point
Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.
M&L PCC in foundations, filling and mass-concrete type D2(1:4:8)using 40 mm graded stone aggregate
M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .
Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in
S&F 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork ,applying evenly a coat of blown type bitumen at the rate of 1.5kg/per sqm and binding with clean dry sand @ 0.05 cum per sqm, polythene film, 150 micron thick,laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sq.mtr complete all as specified and directed.
M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface and
M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface
M&L RCC M-25 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span
M&L RCC M-25 design mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like
M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality
M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat
Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs n exc 20 cm wide & sides of RCC/PCC bands in walls, horizintal or sloping & similar work exc 10cm but n exc 20cm wide Roughed finished surface of concrete
Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat
Hardcore of Broken brick bats n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface
M&L 50mm thick PCC type C-1, (1:3:6) using 20mm graded stone aggregate Finished even & smooth without using extra cement as in plinth protection
M&L continuous brick edging, with burnt clay bricks of sub class ‘B’ (old size) with width equal to the depth of the brick laid dry on end vertically including sand cushioning & filling interstices with sand (Tibba sand) complete all as specified.
M&L, 15mm thick rendering in CM 1:6 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement.
M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling
M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) finished even & smooth (without using extra cement)
Applying three coats of white wash on new Ceiling surface including preparation of surface.
Applying two coats of white wash on new wall surface including preparation of surface.
Applying two coats of cement base paint, white or tinted on new wall surface including preparation of surface.
S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, in opening as per specification & drawing
S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.
S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section.
S&F Aluminium handles 125mm size, cast type, anodised
S&F 100 mm long butt hinges extruded almiunium alloy with galvanised mild steel hinges pin, anodised and fixed all as specified and directed by Engineer-in-Charge.
S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 105 x 60mm all as specified and directed.
M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified and directed.
S & F flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified.
S&F Aluminium handle cast type anodized 150 mm long all as specified.
S&F Aluminium alloy, anodised sliding door bolt with hasp and staple ( bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or stainless steel 300mm size all as specified and directed .
S&F Aluminium anodized barrel tower bolt of extended section and fixed 200 mm long all as specified and directed.
S&F powder coated anodized aluminum frame for doors, windows , ventilators with one of more rebates including joining cleat for fixing etc. completed all as specified
S&F Sheet glass frosted one side 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane
S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specifed and directed.
M&L 100mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate)
S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4)
M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge.
S&F Vitreous China wash down water closet pan (Pedestal pattern) white excluding fixing bolt incl plastic water closet seat cover and mild steel chromium plated or aluminised hinging device and jet spray complete fixed in repair.
S&F Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets, CP, brass, Waste fittings 32mm bore & PVC Waste Pipe 32 mm bore
S&F CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe
S&F Angle Stop valves 15 mm bore fancy type, CP, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions
S&F Bib taps fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed
S&F PVC connections 15mm size with PTMT nuts of length 450mm
S&F CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges
S&F Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions
S&F Ball valves PTMT 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule
Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified.
Supplying and laying of CPVC pipes 20mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified
S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors
S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors
S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls
S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with acces door
S&F 75mm PVC (SWR) vent cowl
M&L 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement
Material and labour DWCPE pipe 150 mm dia ( 160 mm OD) completed laid in trenches including earthwork, removal and return filling and jointed including testing alongwith necessary jointing material tees/union/socket etc complete laid on PCC bed 150mm thick PCC in 1:3 type C2 of avg depth 0.90 to 1.65 m depth incuding packing under and haunching against the side of pipes after they are laid and tested all as specified in IS 16098:2013 and as directed.
M&L PCC in foundations, filling and mass-concrete type C2 (1:3:6) using 40 mm graded stone aggregate
Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4)
M&L PCC in surface channels and drains type B1 (1:2:4) using 20 mm graded stone aggregate
Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extgra cement including forms, moulds mitred/stopped ends etc.
M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) mixed with water proofing compound 3% by weight of cement finished even & smooth without using extra cement ( WPC shall be measured & paid separately)
M&L Rendering 10mm thick on fair face of brick work/concrete surfaces in CM (1:4)
Supplying only Integral waterproofing compound
M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:6) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces
S&F Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe
Supplying and laying of CPVC pipes 25mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified
M&L chequred cement concrete tiles gloss finish 30cm X 30cm X 25mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors complete all as specified and directed.
M & L for 75mm thick cement concrete type D-2 (1:4:8) using 40mm graded stone aggregate as in sub floors, sub bases etc all as specified and directed by Engineer - in - Charge.
S&F Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe)
S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity
M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code ISI marked and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/exhaust fan controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified (Cost of MS sunken box and bakelite sheet included in the rate).
All as per Srl item No. 78 here-in-before but one three pin socket outlet 5 Amps on the independent board complete all as specified.
All as per Srl item No. 78 here-in-before but one three pin socket outlet 5 Amps on the same board complete all as specified.
S&F switch Piano type single pole one way 5 Amp,230 VAC supply.
S&F socket two in one ,3 Pin 5 Amps 230 VAC supply, .
Supply & fixing PVC Lamp holder suitable for and including batten fittings ,LED Electric lamp 9 Watt with backalite 20mm back plate complete all as specified & directed, .
M&L for Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed.
S & F of MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 6 to 32 Amps all as specified and directed.
S & F of MCB suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA and 16 to 40 Amps all as specified and directed.
S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN4 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..
S&F and testing LED light fitting 1x18watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through h oles. The system wattage of fitting should not be more than 18 watt= 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 1700 lumens, total input voltage range 140-280V AC, colour rendering index should not be less than 80, Corelated colour should be minimum 6000 degree Kelvin.
S&F for WEE Plus LED bulk head luminaire of capacity 10 Watt an ideal energy efficient solution for upgrading conventional GLS bulkhead luminaires to LED bulk head IP 65 complete all as specified and directed by Engr-InCharge Make: Bajaj BIBWP LED 10W WH or equivalent in Havlls/Crompton Greaves/ Philips/Wipro/Syska as approved by GE.
S & F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 3 core
S&F of Exhaust fan 250 mm 240 volts with metal body and louvers with incl all accessories and making hole, fixing, plastering, painting with existing color at site, after finishing the work.
Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 25 mm dia bore.
Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 20 mm dia bore.
S & F stop valve size 25 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.
S & F stop valve size 20 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.
S & F PVC moulded three layer tank of cap 500 Ltr with complete all accessories
M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable ISI marked in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified.
S&F switch Piano type single pole one way 15 Amp on laminated sheet top cover complete to all as spd (Sheet top cover incl in point wiring) .
S&F socket Pinao type 6 Pin 16 amp,230 VAC .
S&F double door SPN DB 4 way having facility to fix MCB DP/SPN 8 ways complete fitted with bus bars, neutral links including provision of MCB SP/SPN 6-16A-32A and making good disturbed surface area complete all as specified and directed. make- Legrand/L&T Hager/C&S/INDO KOPP/Indo Asian/Standard/Havells/Topson
Material and labour for sand cushioning, with dry and clean fine river sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and as directed. (Note:- Punned thickness shall be considered for payment purpose)
Supply and laying Best quality, locally available, sub class ‘B’ bricks (Old Size) for cable protection cover, laid flat and dry in trenches over the cable , perpendicular to the direction of cable complete all as specified and as directed.
M&L for boring hole across the road/plinth/hard standing by trench less technology method suitable for up to 100 mm bore pipe for 0.4 mpa working pressure for cable passing without damaging Road/plinth/floor complete all as specified and directed by Engr-In-Charge.
Supply and fixing GI tubing light grade of size 50 mm bore, ISI marked, fixed along poles/walls or laid in trenches, under road for cable protection including fittings (elbow, tee, socket etc) including taking out old pipe any size complete all as specified and as directed. (Note:- Excavation and earthwork and MS clamp as required shall be measured and paid separately under respective item of Sch.)
Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 50 mm dia bore.
M &L for cutting existing Steel tubing laid in trenches of any size for addition and alternation
M&L Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector
S & F stop valve size 50 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.
Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core
Suppy and fixing Exhaust fan metalic body heavy duty of size 300 mm sweep with louver shutter 220V, single phase AC including 1.0sqmm copper flexible cable twiested three core alongwith flelxible PVC condiut from ceiling rose to fitting testing complete all as specified and directed including cutting holes thruogh cement mortor wall for fixing 300mm sweep exhaust fan grouting the bolts, plastering and making good surface internally and externally wth existing colour.Make:Cromption/Havells/Bajaj
Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire of size 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto electric equipment, fixing with 02 Nos nuts and bolts. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) including taking out/dismantling old unserviceable earthing system complete all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.
Trial bore of 200 mm dia upto 50 meter depth below ground level in any kind of soil strata including hard stone/boulder including electric logging, MS cap, MS flat iron clamps, reducing socket etc.
All as per item no 112 but depth below 50 meter to 100 meter
All as per item no 112 but depth below 100 meter to 150 meter
Development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water.
Yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield complete all as specified
Supply jointing and lowering PVC slotted 150mm dia heavy duty including providing suitable jail on the slotted pipe.
Supply jointing and lowering PVC 150mm dia heavy duty pipe including joints
Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 80 mm dia bore.
Supply and fixing GI pipe galvanised " Medium class " with all fitting laid in trenches of size 40 mm dia bore.
S & F stop valve size 40 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for unions and fixed.
S & F butterfly valve of size 80 mm complete all as specified and directed.
S&F "D" Joint with nut and bolt suitable for 80mm bore DI/CI pipes and fittings and replacing with newly connecting GI pipe of existing size connected to the DI/GI pipelines complete all as specified and as directed by Engineer-in-Charge.
S&F "D" Joint with nut and bolt suitable for 150mm bore DI/CI pipes and fittings and replacing with newly connecting GI pipe of existing size connected to the DI/GI pipelines complete all as specified and as directed by Engineer-in-Charge.
M&L 150mm thick PCC 1:2:4 typeB- 2, (40mm graded aggregate) as in flooring all as specified and directed.
Dismantling floor, earth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises
S&F Machine pressed precast concrete interlocking paver block (Except tiles) any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade laid over 50mm thick sand cushion complete all as specified.
Demolition of cement concrete (un reinforced ) of any description and in any position.
M&L Bituminous premix asphaltic dense concrete 40mm consolidated thickness with 6% binder content by weight of total mix, rolled and compacted to required camber and gradient complete of approved make all as directed by Engineer -in-charge.
Supply installing lowering and connecting up commissioning and Testing submersible solar pump of discharge 272 LPM at 30 Mtr head coupled with 3 phase AC motor of capacity 5 HP including 2 inch DPE delivery pipe with clamp, rope, 3 core SB wire of size 2.5 sqmm from starter to summercible pump complete with 5 KW solar panel with GI structure, solar controller, modules, lightening arrester, feeder pillar box with starter and necessary plinth of size 2 meter X 2 meter works as specified by company, complete all as specified and directed.
M&L for Earthing complete with using copper plate electrode 60×60cm ×3.15mm thick electrode , buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to and 20×3mm copper strip as earthing lead thick earth means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion Note:- Excavation and returning filling deemed to be included in quoted rated
Supply installing 180/360 degree Rain gun with gear - driven, rotary type, capable of covering a 26 (ft) radius at 40 PSI with a discharge rate of 2.1GPM at 180 degree and 4.4 GPM on complete adjustable shall be available with eight (8) nozzles discharging from 0.64 to 5.3 GPM. The raingun shall have radius reduction capabilities by means of stainless steel nozzle retainer/radius adjustment screw and QR coupling valve for direct fitting into the pipes and all other accessories as needed as directed Note:- Rates are deemed to including all accesories needed at ground for all guns to be fitted.
G S CONSTRUCTIONS
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .