Repairs to Sunken floors roofs joinery sanitary fittings plastering internal water supply and certain other misc works at EME Wksp Stn HQ and other compressive maint works of MES staff Qtrs in the area of AGE B/R-II under GE(N) Ahmednagar

Amount

Dismantling of stone slabs and tiles of any descriptions or thickness in floors, approns etc laid and bedded in any mortor etc complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (un-reinforced) in ground floors and paving not exc 15 cm thickness below or above ground level etc complete all as specified and directed by Engineer-in-Charge

Dismantling of PGI /translucent sheets of any guage or any thickness etc complete all as specified and directed by Engineer-in-Charge

Dismantling Asbestos cement (corrugated, Semicorrugated etc.) sheets in roof coverings etc complete all as specified and directed by Engineer-in-Charge

Dismantling of framed trusses not exceeding 10mtr span made of wood/steel etc complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster of any thickness on brick/stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkats or frames not exc 1.50sqm with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkats or frames exc 1.50sqm not exc 4.00sqm with shutters (without taking off shutters from the frames) etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description not exc 1 Sq. m each etc complete all as specified and directed by Engineer-in-Charge

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each etc complete all as specified and directed by Engineer-in-Charge

All as per item No 10 (here-in-before) but exc 2 Sqm.

Dismantling of Posts or studs, embeded concrete, brick work, (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground etc complete all as specified and directed by Engineer-in-Charge

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc nexc 10Sqm on plan and n.exc 1.5m in depth and getting out soft/loose soil and getting out etc complete all as specified and directed by Engineer-in-Charge

Excavating in post holes (or similar holes) each n exc 0.5 cu. m in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing the surplus spoil to distance n exc 50 m etc complete all as specified and directed by Engineer-in-Charge

M&L for moorum/red bajri filling in floors or pavings, laid in trenches n.exc. 15cm thick , speread , levelld and rammed including watering etc complete all as specified and directed by Engineer-in-Charge

M & L for hard core of gauge n exc 63mm deposited spreading & levelling in layers n exc 15 cm thick watered & rammed to a true surface etc complete all as specified and directed by Engineer-in-Charge

M&L for RCC (1:2:4) type B1 using 20mm graded stone agrregate as in foundations, including rafts, foundation beam, plinth beams, based for columns, etc, basement slabs and mass concrete etc complete all as specified and directed by Engineer-in-Charge

M & L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floor 75mm thick etc complete all as specified and directed by Engineer-in-Charge

Material and labour for plain cement concrete in PCC (1:3:6) type C2 using 40 mm graded stone aggregates in foundation, filling and mass concrete for similar work etc complete all as specified and directed by Engineer-in-Charge

M&L for Pre-cast cement concrete block masonry with solid blocks, (1:3:6) Type C-1 (20 mm graded stone aggregate) exc. 10 cm in width and setting in mortar, Set in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

All as per item No 20 (here-in-before) but expect Pre-cast cement concrete blocks

Removing excavated materials (soil) exc 250m but n exc 500m and depositing where directed at a level n.exc 1.50m above the starting poing etc complete all as specified and directed by Engineer-in-Charge

Material and labour for joint free / rectified non skid ceramic coloured tiles as specified in PS, 8-10 mm thick as approved by GE (square / rectangular) size of tiles 300x300 mm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed in grey cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

Material and labour for coloured glazed ceramic tiles digitally printed premium designer series of size of tiles 350x450 mm , 8-10 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in cement and sand mortar (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles etc complete all as specified and directed by Engineer-in-Charge

Material and labour for machine cut Kota stone slab 20 to 25mm thick (minimum size 30cm x 45cm) as in flooring, laid over and incl cement screed bed 15mm thick in cement and sand mortar (1:4), and set and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab incl rubbing and granite polishing etc complete all as specified and directed by Engineer-in-Charge

Material and labour for rough dressed shahabad stone, 25 mm to 40 mm thick laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), laid and jointed pointed in cement and sand mortar (1:3) etc complete all as specified and directed by Engineer-in-Charge

Material and labour for Vitrified ceramic tiles,10 mm thick (square / rectangular) of size 600 x 600 mm of any shade as approved by GE as in floor etc laid over and including roughning existing surface , making good the damaged surface, levelling, and fixing with cement based tile adhesive as per the manufecturer's instructions and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

All as per Sl item No 27 (here-in-before) but on skirting / Dado.

Material and labour for joint free / rectified ceramic coloured tiles of size 600x600 mm as specified in PS, 8-10 mm thick as approved by GE (square / rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed in grey cement slurry and pointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

Material and labour for 16 to 18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in cement and sand mortar (1:4) jointing & pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polishing to achieve mirror finish etc complete all as specified and directed by Engineer-in-Charge

Material and labour for machine cut cudappah stone slab 20-25 mm thick over cement screed base, full round moulding the edge laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M & L for Chequred cement concrete tiles with pigment 25 cm x 25 cm x 25 mm thick, set, jointed and pointed in neat cement slurry as in floors over and including screed bed of 15 mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M & L for Glossy finish Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade incl sand cushioning 30 mm thick etc complete all as specified and directed by Engineer-in-Charge

Material and labour for second class hard-wood in scantlings clean sawn etc complete all as specified and directed by Engineer-in-Charge

Supply and fix pressed steel frames (thickness of MS sheet 1.25mm) of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge

All as per item No 35 (here-in-before) but pressed steel frames of size 125 mm X 60 mm

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, etc complete all as specified and directed by Engineer-in-Charge

Material and labour for filling in door frames in plain cement concrete, (1:2:4) type B0, using 12.5 mm graded stone aggregates etc complete all as specified and directed by Engineer-in-Charge

M & L for 2nd class softwood plain fillets square rectangular or triangular section clean sawn and fixed with nails or brads exc 13 and n.exc 25 sqcm etc complete all as specified and directed by Engineer-in-Charge

Material and labour for second class hard wood beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc.and removing old beads etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 2nd class hard wood 35 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and directed by Engineer-in-Charge

All as per item No 42 (here-in-before) but 30 mm thick as in window or ventilators.with sash bars

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face etc complete all as specified and directed by Engineer-in-Charge

Supply and fix steel windows with side hung double shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed by Engineer-in-Charge. Notes: 1) Suppt only guard bars shall be measured and paid separately as supply only. 2) M & L for galzing shall be measured and paid separately.

Supply and fix steel ventilator with top hung shutter including hinges, steel peg stay aetc complete all as specified and directed by Engineer-in-Charge. Notes: 1) Supply only guard bars shall be measured and paid separately as supply only. 2) M & L for galzing shall be measured and paid separately.

Supply and fixing powder coated aluminium door shutters with frame in two panels made of section 47.5x44.45x2.25mm @1.12 kg/RM frame, vertical styles of section 47x44.5x2.75mm thick @ 1.15kg per RM, top rail & lock rail of section 47.5x44.5x2.75mm @ 1.33 kg per RM, bottom rail made of section 114.6x44.45x2.3mm@ 2.06 kg per RM with securing rebate @ 0.102 kg per RM with & incl 5mm thick plain sheet glass incl necessary screw, jointing cleats, glazing clip, rubber packing, aluminium snap beeding etc complete all as specified and directed by Engineer-in-Charge

Supply and fix power coated aluminium three track window made out of Jindal aluminium sections Nos. 20671, 20672, 20690 & 20668 including 5mm thick plain sheet glass including rubber / neoprene beading and locking arrangement etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated anodised aluminium frame for windows, ventilators with one or more rebates incl joining cleats for fixing etc complete all as specified and directed by Engineer-in-Charge

Supply only mild steel square guard bars 10 mm welded to steel windows / ventilators etc complete all as specified and directed by Engineer-in-Charge

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix mild steel tower bolt stove enamelled black with bright bolt 200mm long etc complete all as specified and directed by Engineer-in-Charge

Supply and fix mild steel pressed handles oval type stove enamelled black of size 150mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 54 (here-in-before) but in repairs

Supply and fix aluminium anodised barrel tower bolt of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 56 (here-in-before) but in repairs

Supply and fix aluminium anodised handles of extruded section 150mm long etc complete all as specified and directed by Engineer-in-Charge

All as per item No.58 (here-in-before) but in repairs

Supply and fix aluminium die cast body door closure , hydraulically regulated of designation 2, universal type for door shutters weighing between 36 to 60 Kg etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 60 (here-in-before) but in repairs

Supply and fix mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 62 (here-in-before but in repairs

Supply and fix in repairs peg stay for steel windows of approved make / sample etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 32mm dia mild steel chromium plated curtain rods incl brackets etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 66 (here-in-before) but fixed in repairs for wooden door/window.

Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads etc complete all as specified and directed by Engineer-in-Charge

M&L for, frosted glass 5mm thick glazing with oil putty in squares exc 0.5 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing 3.00 mm thick ordinary quality plain sheet glass with oil putty in squares n exc 0.50 Sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M&L for frosted glass 3mm thick glazing with oil putty in squares n exc 0.5 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

Material and labour for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new steel/steel ornamental and iron surfaces of any description exceeding 10cm in width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer etc complete all as specified and directed by Engineer-in-Charge

M&L for complete removal of existing treatment of walls or other plastered surfaces and preparing the surfaces and applying two coats of OBD (washable) over a layer of 2mm thick wall putty at any height etc complete all as specified and directed by Engineer-in-Charge

M&L for preparing old plastered surfaces and applying one coat of OBD (washable) at any height etc complete all as specified and directed by Engineer-in-Charge

M&L for preparing new plastered complete and applying two coats of Cement Paint at any height etc complete all as specified and directed by Engineer-in-Charge

M&L for preparing old plastered complete and applying one coat of Cement Base Paint at any height complete all as specified &directed by Engineer-in-charge.

Welding in repairs n. exc 2.5cm in length and n exc 6 mm in thickness etc complete all as specified and directed by Engineer-in-Charge

Taking up or down steel tubing for 15mm dia bore etc complete all as specified and directed by Engineer-in-Charge

All as per item No 79 above but, 20 mm dia bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing 15 mm bore 3 Layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

All as per item No 82 (here-in-before) but, 20 mm dia bore etc.

Supply and fix in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs PVC bib tap 15 mm dia, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge. Make Prayag

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe etc complete all as specified and directed by Engineer-in-Charge

Supply and fix PVC connections 15 mm size with PTMT nuts of length 600 mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix repairs PVC valveless, syphonic action type, flushing cistern,low level, all accesories etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren etc complete all as specified and directed by Engineer-in-Charge

Supply and fixed in repairs 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge

All as per item No 90 (here-in-before) but 75 mm dia

Supply and fix in repairs 110 mm bore PVC (SWR) bend, any radius etc complete all as specified and directed by Engineer-in-Charge

All as per item No 92 (here-in-before) but 75 mm bore.

Supply and fix in repairs 110 mm bore PVC (SWR) branch piece single (single Y) equal or unequal etc complete all as specified and directed by Engineer-in-Charge

All as per item No 94 (here-in-before) but 75 mm bore.

Supply and fix in repairs 110 mm bore PVC (SWR) branch piece double (double Y) equal or unequal etc complete all as specified and directed by Engineer-in-Charge

All as per item No 96 (here-in-before) but 75 mm bore.

Supply and fix repairs PVC (SWR) floor trap, 75 mm dia with grating including jointing with slovent cement etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs stack clamps made out of FI 50 X 5 mm and 16 mm dia round iron stays,including bolt and nuts and securing ends of stays to wall for 75 to 100 mm dia pipe etc complete all as specified and directed by Engineer-in-Charge

Supply and fixed in repairs 32 mm dia PVC flush pipe for low level flushing cistern and conecting to pedestal pan including jointing etc complete all as specified and directed by Engineer-in-Charge

Supply and fix rotational moulded polyethylene water storage tanks double layer ISI marked conforming to IS 12701-1996 (cylindrical vertical with closed top) and made out of virgin FDA approved polyethylene material of 500 litres capacity hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 101 (here-in-before) but water storage tank of capacity 1000 litres

All as per item No 101 (here-in-before) but water storage tank of capacity 2000 litres

Supply and fix in repair ball brass valves, 15 mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed all as directed.

All as per item No 104 (here-in-before) but 20 mm dia bore.

All as per item No 104 (here-in-before) but 25 mm dia bore.

Supply and fixed in repairs 32 mm dia PVC waste pipe (outlet pipe) plain fixed to waste coupling of WHB or Sink etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 107 (here-in-before) but 38 mm dia

Supply and fix in repairs 32 mm dia PVC waste pipe for urinals (outlet pipe) plain with fixing accesories etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm, waste chain and plug and porcelain stopper , waste pipe, a pair of brackets,or errecting stand etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixe in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs looking mirror of size 600 mm X450 mm etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs looking mirror of size 600 mm X 1200 mm etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs, Stainless steel grating 100 mm dia etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs, shower rose with shower arm etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs plastic water closet seat cover, colored closed patern with flat bottom. cover and mild steel cromium plated or alumlised hinging device etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs framed work such as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other coverings, doors etc to be prepared for handing or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc complete all as specified and directed by Engineer-in-Charge.

S&F of rolled steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 (Gde-E- 250) quality-A etc complete all as specified and directed by Engineer-in-Charge.

S&F for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0

Dismantling fencing wire mesh, any type etc complete all as specified and directed by Engineer-in-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire etc complete all as specified and directed by Engineer-in-Charge.

Supply only Chain link MS galvaised fencing, any size or type etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs Steel Rolling shutters 1.25mm thick gear operated type with chain wheel and hand chain as specified incl top cover, anchoring rod hasp and staple and one shop coat of primer erected in position as indicated complete : push pull or manual type etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains; hand made sliding bolts, clamps, hold fasts, wall ties, plain angle cleats and similar small articles etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 10 mm thick in cement and sand mortar (1:4) on stone masonry surface finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

M&L rendering 15mm thick in cement and sand mortar (1:6) on brick or concrete surface and finishing even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Material and labour in repairs for false ceiling with Vinyle faced Arm-Gyp-FB, ceiling 600 x 600 x 9mm thick with washable metallized polyster foil backing with Vinyle covered edges, supporting sections shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre as per manufacturere's instructions / specification and etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 128 (here-in-before) but expect supporting sections snap grid

M & L 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof walls fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as specified and directed by Engineer-in-Charge.

S&F Asbestos cement two piece adjustable serrated ridge for corrugated or semi-corrugated sheets fixed with L- ype or J-type hook bolts etc complete all as specified and directed by Engineer-in-Charge.

M&L for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE etc complete all as specified and directed by Engineer-in-Charge.

M&L for pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for special treatment to sunken slab floor incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in cement and sand mortar (1:4). Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished rainforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torach and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC viterous china squatting pan 580x440mm with integral footrests/pedastal pan incl seat cover, white, area of WC exc 1.50 Sqm but nexc 5.00 sqm etc after dismantling the existing sunken floor etc complete all as specified and directed by Engineer-in-Charge. Note : Work has to be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap etc complete all as specified and directed by Engineer-in-Charge.

M&L for stone sett flooring with stone seets of size 200 to 250mm long 150 to 200mm wide and 150mm deep and sides dresses bedded in cement and sand mortar (1:3 )joints 20mm thick grouted in cement and sand mortar (1:2) with admixture of matalic floor 5% by weight of cement struck flush etc complete all as specfied and directed by Enigneer-in-Charge

M&L for edge stones to flooring with stone setts of size 250 to 300mm long 150 to 200mm wide and 450mm deep etc complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge .

Dismantling of aluminium door/windows/ventilator shutter from frame and M&L in replacement necessary accessories like floor spring, gasket rubber beading, glass of any description,etc. and again reassembled and fixed in the same opening complete all as specifed and directed

An amount of Rs 1,30,180.00 shall be deducted from BOQ on account of schedule of credit

Takshashila electricals

M/s. A P INFRA

M/S-B.R.SONAWANE

M/s AG PATHAN

M/S MAHESHWARI ENTERPRISES

MS. G.A. CONSTRUCTION

Arihant Construction

M/s IBEX Engineers and Contractors