Loading
Loading…
Loading…
Tender Value
₹4.2 Cr
EMD Value
₹3.6 L
Closing Date
6 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
NORTH
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N OR 'V' Whichever is less; where. V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per ANNEXURE-XXXIII, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Trenching, cable laying, location and signal foundation/ erection/ termination/ wiring in connection with any signalling work. OR Any Indoor or combined indoor/ outdoor signalling work including supply, installation, testing and commissioning of relay interlocking (RRI/PI) system for passenger carrying lines.
7 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender document, Scope of work & GCC 2022 are attached with the tender.
Extension of UP & DN loop lines by 75 m at Vangani and Bhivpuri stations in North section of Mumbai Division.
CR-BB-SNT-NORTH-2026-15
CR-BB-SNT-NORTH-2026-15
Open
Works - General
12 Months
Mumbai, Maharashtra
₹0
₹3.6 L
6 Mar 2026
5 Feb 2026
274 items across 8 schedules · ₹3,75,77,040.48 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply of Relay Rack Assembly complete with scaffolding, fixtures and accessories including MS Bars for fixing of relay plug board, string rods, fuse strips with bracket, 11 Way Bus Bars with cover and mounting brackets, runway for cable/wires, frame, base assembly etc. Siemens type & as per extant practice on C. Rly. Typical part list and Rack arrangement as per Sketch no SK-727 and Rack plan as approved by Engineer in charge.(Inspection Agency-Consignee) | Set | 2.00 | 35,301.04 | 70,602.08 |
| 2 | Supply of Tag Blocks 96/100 way with polycarbonate cover as per IRS S 77- 2006(Rev.1) Requirement of each type shall be specified by Engineer-in-charge.(Inspection Agency-Consignee) | Numbers | 4.00 | 1,497.03 | 5,988.12 |
| 3 | Supply of Main Cable Termination rack complete with scaffolding, fixtures & accessories including square bars for mounting 8-way terminal blocks, ladder, string rods, frame, base assembly, insulators, J bolt, nut/bolts & fasteners, backelite sheet, etc. Siemens type and as per extant practice on Central Railway. Typical part list and rack arrangement shall be as per sketch No. SK-727 with latest alterations.(Inspection Agency- Consignee) | Set | 2.00 | 30,404 | 60,808 |
| 4 | Multi port front end processor with two nos. of dual card modems with and 230/12V charger and 24V, 42AH maintenance free battery. SPN NO. Spec No. IRS-S-99/2006 (Amdt-3). (Inspection Agency-Consignee) | Set | 1.00 | 2,31,623.71 | 2,31,623.71 |
| 5 | Supply of Indoor Jumper Wire ATC 1 x 1 mm dia. conforming to IRS 76/89 (Amd.3) or latest. (Inspection Agency-Consignee) | Kilometre | 2.00 | 13,093.54 | 26,187.08 |
| 6 | Supply of PVC flexible copper cable single core multistrand 1 x 2.5 Sq.mm (50 conductor each diameter 0.25 +/- 0.01) as per IS 694/2010 with latest amendment if any.with insulation thickness of 0.70mm nominal conductor resistance 7.98 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3).(Inspection Agency-Consignee) | Kilometre | 1.00 | 44,575.65 | 44,575.65 |
| 7 | Supply of PVC flexible copper cable single core multistrand 1 x 6 Sq.mm (84 conductor each diameter 0.30 +/- 0.01) as per IS 694/2010 with latest amendment if any.with insulation thickness of 0.80mm nominal conductor resistance 3.30 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3).(Inspection Agency-Consignee) | Kilometre | 1.00 | 91,617.31 | 91,617.31 |
| 8 | Supply of PVC flexible copper cable single core multistrand 1 x 10 Sq.mm (80 conductor each diameter 0.40 +/- 0.01) as per IS 694/2010 with latest amendment if any.with insulation thickness of 1.0mm nominal conductor resistance 1.91 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3).(Inspection Agency-Consignee) | Kilometre | 1.00 | 1,41,059.3 | 1,41,059.3 |
| 9 | Supply of PVC flexible copper cable single core multistrand 1 x 16 Sq.mm (126 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS:694/2010 with latest amendment if any with insulation thickness of 1.0mm nominal conductor resistance 1.121 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3). (Inspection Agency-Consignee) | Kilometre | 1.00 | 2,09,928.3 | 2,09,928.3 |
| 10 | Supply of PVC flexible copper cable single core multistrand 1 x 25 Sq.mm (196 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS:694/2010 with latest amendment if any with insulation thickness of 1.2mm nominal conductor resistance 0.780 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3). (Inspection Agency-Consignee) | Kilometre | 1.00 | 3,26,216.47 | 3,26,216.47 |
| 11 | Sealed maintenance free VRLA Battery/Cell 2 Volt, 300AH IRS : S-93/96 (A) (Amd.1) or latest. (Inspection Agency-RDSO) | Numbers | 60.00 | 5,040 | 3,02,400 |
| 12 | Sealed maintenance free VRLA Battery/Cell 2 Volt, 200AH RDSO SPN/93/96 (A) (Amd.1) or latest.(Inspection Agency-RDSO) | Numbers | 60.00 | 3,062.7 | 1,83,762 |
| 13 | Supply of Battery Charger self regulating floor mounting type with 230 V AC single phase input and output 60 V DC, 20A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments.Ripple free suitable for digital axle counters.(Inspection Agency-Consignee) | Numbers | 1.00 | 52,992.67 | 52,992.67 |
| 14 | Supply of Battery Charger self regulating floor mounting type with 230 V AC single phase input and output 60 V DC, 40A as per spec. IRS.S.86/2000(Amd.4) with latest amendments.Ripple free suitable for digital axle counters.(Inspection Agency-Consignee) | Numbers | 1.00 | 1,30,799.67 | 1,30,799.67 |
| 15 | Supply of Battery Charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC, 20A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments.Ripple free suitable for digital axle counters.(Inspection Agency-Consignee) | Numbers | 4.00 | 37,823.73 | 1,51,294.92 |
| 16 | Supply of Battery Charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC, 30A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments.Ripple free suitable for digital axle counters.(Inspection Agency-Consignee) | Numbers | 4.00 | 32,092.68 | 1,28,370.72 |
| 17 | "Relay base plate complete with amphanols, code pins, fixing screws etc.suitable for Metal to Metal K-50 mini groups/ECRs of Siemens Make or functional equivalent of other makes. Note : Relay base plates, are to be procured from Relay manufacturer(OEM). Manufacturer's Certificate for procurement and guarantee in this regard should be furnished. The payment to be released only after Manufacturer's Certificate is submitted. (Inspection Agency- Consignee)" | Numbers | 20.00 | 729.85 | 14,597 |
| 18 | "Major Relay Group Base Plates, complete with fedlisters (20 No per base plate), guide rails and other accessories suitable for major group of Siemens make or functional equivalent of other makes. Note : Relay base plates, are to be procured from Relay manufacturer(OEM). Manufacturer's Certificate for procurement and guarantee in this regard should be furnished. The payment to be released only after Manufacturer's Certificate is submitted. (Inspection Agency-Consignee)" | Numbers | 3.00 | 13,439.58 | 40,318.74 |
| 19 | Supply of Signal Group 2 Aspect without baseplate Siemens Make [No. A-RT-RG-A066] or functional equivalentand should be suitable for working with LED based signal lighting unit. (Inspection Agency-Consignee) | Numbers | 3.00 | 51,784.19 | 1,55,352.57 |
| 20 | Supply of Shunt Signal Group Siemens make [No. A-RT-RG-A065] or functional equivalent without base plates (suitable for LED Signal). (Inspection Agency-Consignee) | Numbers | 4.00 | 57,480.25 | 2,29,921 |
| 21 | Supply of Point Group RRI, Siemens (No.RSSK 3515/19) or functional equivalent without base plates.(Inspection Agency-Consignee) | Numbers | 3.00 | 91,454.4 | 2,74,363.2 |
| 22 | Supply of Point Chain Group Siemens make (No. RSSK 3515/3)or functional equivalent without base plates.(Inspection Agency-Consignee) | Numbers | 2.00 | 31,650.28 | 63,300.56 |
| 23 | Supply of Time Element Relay (Clock work type) AG timer Siemens Make (No RSSK 30/0052) or GIC make or functional equivalent. (Inspection Agency-Consignee) | Numbers | 2.00 | 7,793.62 | 15,587.24 |
| 24 | Supply of Plug In type Relay Metal to Metal type neutral relay mini groups (Non AC Immunised) Siemens make (No. RSSK 30/0011) (Ref. IRS:S46/74 with Amd. 1 & firms specification) or functional equivalent without base plates.Contact configuration 5F/3B or 6F/2B or 4F/4B to be specified by Engineer incharge. (Inspection Agency-Consignee) | Numbers | 7.00 | 7,143.02 | 50,001.14 |
| 25 | Supply of Plug In type Relay Metal to Metal type neutral relay mini groups (AC Immunised-1) Siemens make (No. RSSK 30/0078-1) (Ref. IRS:S46/74 with Amd. 1 & firms specification).or functional equivalent without base plates.Contact configuration 5F/3B or 6F/2B or 4F/4B to be specified by Engineer incharge. (Inspection Agency-Consignee) | Numbers | 7.00 | 8,686.87 | 60,808.09 |
| 26 | Supply of Plug In type Relay Metal to Metal type neutral relay mini groups (AC Immunised) Siemens make (No. RSSK 30/0078) (Ref. IRS:S46/74 with Amd. 1 & firms specification) or functional equivalent without base plates.Contact configuration 5F/3B or 6F/2B or 4F/4B to be specified by Engineer incharge. (Inspection Agency-Consignee) | Numbers | 7.00 | 9,072.04 | 63,504.28 |
| 27 | Supply of Auto Signal Block Proving Relay Group Siemens make [No. A-RT-RG-A056] or functional equivalent without base plates. (Inspection Agency-Consignee) | Numbers | 3.00 | 53,261.72 | 1,59,785.16 |
| 28 | Supply of Metal-To-Metal Universal LED type E C R Siemens make (type A-RT-RG-A064) or functional equivalent without base plate, should be suitable for working with LED based signal lighting unit. IRS:S:46 & STS/E/RELAYS/AC LIT LED SIGNAL/09-2002 Amd.1.(Inspection Agency-Consignee) | Numbers | 10.00 | 6,923.11 | 69,231.1 |
| 29 | Supply of QNA1 AC immunised relay, 8F-8B, 24 VDC along with plug board, retaining clip and connectors confirming to BRS : 931A, IRS:S60, IRS:S34 & IRS:S23(Inspection Agency- Consignee) | Numbers | 7.00 | 3,852.35 | 26,966.45 |
| 30 | Supply of Domino units with cover plate as per approved panel diagram, each of size 54 x 34mm completely wired up similar to Siemens make. Each domino units should have all the 15 contact terminals wired up.(Inspection Agency- Consignee) | Numbers | 30.00 | 1,619.54 | 48,586.2 |
| 31 | Supply of Test Board & Circuit progress board for relay room as per Drg No RST/C/105 A&B. (Inspection Agency-Consignee) | Numbers | 1.00 | 12,559.9 | 12,559.9 |
| 32 | Panel Indication bulbs (Double LED type ) working voltage 24V- Colour- Red/Yellow/Green. (Inspection Agency-Consignee) | Numbers | 75.00 | 44.68 | 3,351 |
| 33 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92 With holder 1.6 A (System, Rapid or Malnad make).(Inspection Agency-Consignee) | Numbers | 80.00 | 79.92 | 6,393.6 |
| 34 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92 With holder 0.6 A (System, Rapid or Malnad make).(Inspection Agency-Consignee) | Numbers | 80.00 | 77.19 | 6,175.2 |
| 35 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92 With holder 6 A/10A ( D-Type Bharat Linder, L&T or HEVELLS Make). (Inspection Agency-Consignee) | Numbers | 80.00 | 270.59 | 21,647.2 |
| 36 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92Without holder 1.6 A (System, Rapid or Malnad Make).(Inspection Agency- Consignee) | Numbers | 80.00 | 23.02 | 1,841.6 |
| 37 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92 Without holder 0.6 A (System, Rapid or Malnad Make).(Inspection Agency- Consignee) | Numbers | 80.00 | 23.02 | 1,841.6 |
| 38 | Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:78-92 Without holder 6A/10A (D-type Bharat Linder, L&T or HEVELLS Make). (Inspection Agency-Consignee) | Numbers | 80.00 | 95.7 | 7,656 |
| 39 | Design, fabrication and supply of Fuse Auto Changeover System for 32 Nos. of external non-deteriorating type fuses or 'G' type fuses from 0.6A Amp to 4A Amp capacities used in signalling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. As per RDSO Spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any.(Inspection Agency-Consignee)(Note=Quantity unit number should be read as No. of Modules) | Numbers | 8.00 | 26,760.23 | 2,14,081.84 |
| 40 | Design, fabrication and supply of Fuse Auto Changeover System for 24 Nos. of external non-deteriorating type or 'G' type fuses from 4 A to 10 Amp capacities generally used for point operaton circuits. System shall have 6 cards with monitoring of 4 fuses in one card. As per RDSO Spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any.(Inspection Agency- Consignee)(Note=Quantity unit number should be read as No. of Modules) | Numbers | 8.00 | 40,513.38 | 3,24,107.04 |
| 41 | Supply of Main Signal Post 140 mm outer dia 5.6 Mtr Length as per spec No IRS S 6/81 with latest amendments.(Inspection Agency- Consignee) | Numbers | 2.00 | 9,233.4 | 18,466.8 |
| 42 | Supply of Shunt Signal Post with Base (GI Pipe of 80 mm Dia of min. 1 meter length.). (Inspection Agency-Consignee) | Numbers | 2.00 | 2,711.85 | 5,423.7 |
| 43 | Supply of Cast Iron Main signal surface base 140mm as per spec No IRS S-10 and Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg. No. SA- 23156(Adv), SA-23153 (Adv) & SA-23150 (Adv) Alt. 1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C. Rly practice(Inspection Agency-Consignee) | Numbers | 2.00 | 9,034.12 | 18,068.24 |
| 44 | Supply of Cast iron Shunt signal surface base 80 mm as per spec No.IRS S 10 and Drg No.2011/M with latest amendments, as per RDSO Drg No. SA-23156/Drg.No.RST/11413 as per extent C.Rly practice(Inspection Agency- Consignee) | Numbers | 2.00 | 2,071.84 | 4,143.68 |
| 45 | Supply of Signal No.plates. as per Drg No RST- 11393 / SK-842(Inspection Agency-Consignee) | Numbers | 5.00 | 521.69 | 2,608.45 |
| 46 | OFF set bracket 5-1/2 " to suit 140 mm dia CLS Post with two no. of "U" Bolts with nut & washer complete as per RDSO Drg.No.SA-23080 for Signals & Routes(Inspection Agency-Consignee) | Numbers | 2.00 | 999.74 | 1,999.48 |
| 47 | OFF set bracket 3-1/2' for signals & routes. Drawing No. SA 23840 (Adv) Alt-2 as per extent C. Rly practice.(Inspection Agency-Consignee) | Numbers | 2.00 | 5,294.9 | 10,589.8 |
| 48 | Supply of A/AG/C/P/G/IB Board as per Drg. RST- 11444/1(A), RDSO Drg No SA 23460(AG), SA- 23461©, RST-11445. SA 23456(P), SA 23477(G) & SA 23476-77(IB) as applicable respectively with Latest Amendment. (Inspection Agency-Consignee) | Numbers | 3.00 | 561.74 | 1,685.22 |
| 49 | Supply of Stop Board/IB Board as per RST- 11791 (STOP BOARD)/ RDSO Drg No.7235/B as per extent C.Rly practice.(Inspection Agency- Consignee) | Numbers | 2.00 | 3,340.11 | 6,680.22 |
| 50 | Supply of "2 Aspect" Signal Unit in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post Saves pigment finish on the back side of the end inside. White Pigment finish inside the 2 aspect unit to avoid any extra paint cost.(Inspection Agency-Consignee) | Numbers | 2.00 | 30,939.41 | 61,878.82 |
| 51 | Supply of Shunt Signal Position Light Type FRP complete as per RDSO Specification No.RDSO/SPN/ 194/2006/Rev.2.0 or latest with Off set bracket 3-1/2" to be fitted on 140 mm post drawing No. SA 23840(Adv) Alt-2 for dependent type complete with signal unit bracket, terminals etc without lenses, lamp, lamp holder, and to suit LED Signal lamps. (Inspection Agency-Consignee) | Numbers | 2.00 | 13,950.27 | 27,900.54 |
| 52 | Supply of 3 way Junction Route Indicator in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps.(Inspection Agency-Consignee) | Numbers | 2.00 | 45,194.62 | 90,389.24 |
| 53 | Supply of "Calling On" Signal Unit in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED sigal Lamps. (Inspection Agency-Consignee) | Numbers | 2.00 | 8,669.75 | 17,339.5 |
| 54 | Supply of FIBRE GLASS INSULATING FIRE RETARDENT SHEET OF 10 MM THICKNESS AS PER ISO:10192-1982, Dielectric strength- 25KV/mm with glass content 25 to 34% in standard size of 1.10x1.10 Mtr. as per Spec. No. IS:10192-1982.(Inspection Agency- Consignee) | Numbers | 2.00 | 5,300 | 10,600 |
| 55 | Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006(Rev-2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4, SA-23745 Alt.5, SA-23746, SA-23748 Alt.4 & SA-23756A Alt.3.(Inspection Agency- Consignee) | Numbers | 2000.00 | 72.61 | 1,45,220 |
| 56 | Supply of Lamp 110V/24W, 2 Pin for Loc. (Inspection Agency-Consignee) | Numbers | 200.00 | 22.73 | 4,546 |
| 57 | Supply of earth electrode assembly as per Drg.No. CR/S&T/SK-815(Inspection Agency- Consignee) | Numbers | 15.00 | 1,078.08 | 16,171.2 |
| 58 | "Maintenance Free Earth as per RDSO/SPN.197/ 2008 or latest consisting of : 1) Copper bond steel electrode 3 Mtr long 17mm dia with copper bonding thickness of min. 250 micron & UL listed & marked-01 No. 2) Earth enhancement compound RDSO Approved in sealed bag of 10 Kgs - 03 No. 3) Copper strip 150 x 25 x 6mm - 02 No. 4) Copper strip 300 x 25 x 6mm - 01 No. 5) 35 Sqmm Copper Cable to connect earth electrode to MEEB - 15 Mtr Approx.(Inspection Agency-RDSO)" | Set | 10.00 | 17,786.33 | 1,77,863.3 |
| 59 | Supply of Microprocessor based universal earth resistance sensing unit 12 channel AC/DC as per RDSO/SPN/256/2002 with latest amendments.(Inspection Agency-RDSO) | Numbers | 1.00 | 1,45,626.55 | 1,45,626.55 |
| 60 | Supply of Track Lead Juction Boxes as per C.Rly Drg. No.RST 11509 made from fiiber glass alongwith terminal blocks.(Inspection Agency- Consignee) | Numbers | 10.00 | 1,047.98 | 10,479.8 |
| 61 | Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No. IRS: S 17-75 Revision 3. (Inspection Agency-Consignee) | Numbers | 600.00 | 2.01 | 1,206 |
| 62 | Supply of PVC jacketed wire rope for Track Lead connections. PVC jacketed wire rope should be of Galvanised steel wire rope 6 mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS: 2266:2019. Reclaimed or recycled material should not be used.(Inspection Agency-Consignee) | Metre | 2000.00 | 52.29 | 1,04,580 |
| 63 | Supply of 8 SWG GI wire (4mm dia) suitable for track circuit rail bonding. As per IRS Specification S:13 - 62 (Inspection Agency- Consignee) | Kg | 200.00 | 86.82 | 17,364 |
| 64 | Supply of Electronic Timers for DAC reset arrangement 3 sec to 30 sec with 2NO/2NC contact working voltage 24V/60V DC. Siemens/ABB/L&T or SELEC (642XA programmable electronic timer switch) make. (Inspection Agency-Consignee) | Numbers | 10.00 | 2,819.28 | 28,192.8 |
| 65 | Supply of Ground connections, complete set suitable for IRS type/appd. point Machine for ordinary turnout with tounge attachment insulation and other insulation as per RDSO Drg. S/3361 / 62 / 63 for IRS type point machine) or RDSO Drg No.SA-9151/52 (for Siemens point machine) with latest amendements. However the ground connection shall be procured only after confirmation from Railway engineer as per site condition /type of machine/turnout.(Inspection Agency- Consignee) | Set | 3.00 | 8,171.32 | 24,513.96 |
| 66 | Supply of Ground connections,complete set suitable for IRS type/appd. point Machine for derail switch with tounge attachment insulation as per RDSO Drg. S/3361 / 62 / 63 for IRS type point machine) or RDSO Drg No. SA 9151/52 with latest amendements. However the ground connectio n shall be procured only after confirmation from Railway engineer as per latest site condition /type of machine/turnout. (Inspection Agency-Consignee) | Set | 4.00 | 7,142.38 | 28,569.52 |
| 67 | Supply of Point Machine Raised Bracket FRP make with cover as per Drg No.SK-846. (Inspection Agency-Consignee) | Numbers | 7.00 | 878.77 | 6,151.39 |
| Schedule total | ₹50,18,461.92 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY.pdf
CORRECTIONSLIP1to10GCC2022.pdf
FINALNEWTENDERDOC2026-15.pdf
CHECKLISTFORST.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .