Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹97.5 LAccepted-AOC | L1 | Accepted-AOC Being the lowest and reasonable bidder | |
| 2 | L2₹1.1 Cr+₹7.6 L (7.71%)Rejected-AOC 120 144 III PHASE APNA VIHAR JAMMU J K | JAMMU | JAMMU | JAMMU AND KASHMIR | 180010 | L2 | Rejected-AOC Being the other than lowest bidder | |
| 3 | L3₹1.1 Cr+₹8.8 L (8.94%)Rejected-AOC | L3 | Rejected-AOC Being the other than lowest bidder | |
| 4 | L4₹1.1 Cr+₹12.0 L (12.2%)Rejected-AOC PLOT NO 52 BAKSHI NAGAR JAMMU 180001 J K | JAMMU | JAMMU | JAMMU AND KASHMIR | 180001 | L4 | Rejected-AOC Being the other than lowest bidder |
Tender Value
₹1.4 Cr
EMD Value
₹2.1 L
Closing Date
12 Oct 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
HQ CWE Nagrota
HQ CWE Nagrota Co 56 APO
ADDITION/ ALTERATION TO CERTAIN MARRIED ACCOMMODATION BLDG AT NAGROTA UNDER GE NAGROTA
2023_MES_616281_1
CWE/NGT-25/2023-24
Open Tender
Civil Works
Item Rate
365 days
Nagrota
As per NIT and tender documents
8 documents required · 8 mandatory
₹1,000
Yes
GE Nagrota
₹2.1 L
Yes
27 Dec 2023
30 Aug 2023
19 Oct 2023
30 Aug 2023
12 Oct 2023
28 Sept 2023
30 Aug 2023 - 13 Sept 2023
Amount
Demolition of cement concrete concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-Charge.
M & L for 75mm thick cement concrete type C-1 1:3:6 using 20mm graded stone aggregate as in plinth protection complete all as specified and as directed by Engineer-in-Charge
S & F TMT bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips.
M&L for reinforced cement concrete of M 25 grade(using 20mm graded stone aggregates) as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as directed. Note: Reinforcement shall be measured & paid seperately.
Form work to flat surface of soffits of suspended slabs such as roof slab, floor slab, landings and similar work not exceeding 200 mm thick complete all as specified and directed by Engr-in-charge
Demolition of brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified and as directed by Engineer-in-Charge.
M & L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge
M & L for brickwork with subclass `B` bricks, as in half brick wall in straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge
M & L for taking down cement or cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge
M & L for Rendering 10mm thick in cement plaster 1:6 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.
M & L for Rendering 15mm thick in two layer (10mm+5mm) in cement mortar 1:4 on fair faces of brick work / concrete surfaces finished even and smooth with out using extra cement using WPC complete all as specified and as directed by the Engineer-in-Charge Notes:- (i) Water proofing compound to be used only on top layer of plaster (i.e. 5mm thick) (ii) Qty of WPC to be used @200ml per cement bag or as per manufacturer's instructions (iii) WPC shall be measured and paid separately
M&L for 5mm thick rendering in cement and sand mortar 1:3 on ceiling, chajja surfaces (concrete surfaces) finished even and smooth wihtout using extra cement, complete all as specified and directed.
M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge
M&L for vitrified ceramic light shade tiles 10 mm thick (square/rectagular) polished, area not exceeding 0.36 sqm in each tile as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15mm thick screed bed in cement and sand mortar (1:4) complete all as specified and as directed by the Engineer-in-Charge Notes :- (i) Quoted rate shall deem to be included cost of screed bed. (ii) Before executing of tiles work, ATT will be done and ATT will be measured and paid seperately (iii) Colour of tiles shall be approved by GE
M & L for Non-Skid coloured printed ceramic tiles 7 to 8mm thick (square/rectangular), area of each tiles exceeding 0.18sqm and not exceeding 0.38 sqm of each tile, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 for laying tiles in floors etc. complete all as specified and as directed by the Engineer-in-Charge Notes :- (i) Quoted rate shall deem to be included cost of screed bed. (ii) Before executing of tiles work, ATT will be done and ATT will be measured and paid seperately (iii) Colour of tiles shall be approved by GE
M&L for Glazed ceramic coloured printed tiles of size 600 mm x 450 mm x 7mm thick as in dados, skirting, wall etc set jointed in neat cement slurry and pointed in coloured cement to match the tiles over and including 10 mm thick rendering in CM 1 : 4, complete all as specified and as directed by the Engineer-in-Charge Notes:-(i) Colour of tiles shall be approved by GE
M&L for Cement concrete chequered coloured tiles of size 30 cm x 30 cm x 20-22 mm thick, glossy finished set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors complete all as specified and directed. Notes:-(i) Colour of tiles shall be approved by GE
M & L for 75mm thick cement concrete type C-2 1:3:6 using 40mm graded stone aggregate complete all as specified and as directed by Engineer-in-Charge
M & L for 20mm thick (thickness Not less than 20mm) Granite (of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite in single piece only, complete all as specified and as directed by Engineer-in-Charge
M & L for 12mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) over and including 10mm thick cement mortar (1:3) and pointing with white cement using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by Engineer-in-Charge
Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each complete all as specified and as directed by the Engineer-in-Charge
Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed by the Engineer-in-Charge
Taking down shutters of any description exceeding 1 sqm and not exc 2 sqm each complete all as specified and as directed by the Engineer-in-Charge
Resecuring or easing & adjusting shutters of any description exceeding 1 sqm and not exceeding 2 sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge
S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Clerestory windows & other Frames/Chowkhat of Frame size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge
Supply and fixing Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and as directed.
S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate ,etc complete all as specified and fixed
S&F pressed steel fames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate ,etc complete all as specified and fixed
M&L for PCC type B0 1:2:4 (using 12.5mm graded aggregate ), as in foundation, filling and mass concrete using WPC complete all as specified and directed
S & F 35mm thick, flush shutters, solid core construction, with block board core and plywood face panels, with 2mm decorative laminates on both sides of the shutters complete including applying french polish on the doors complete all as specified and directed by Engr-in-Charge
S&F 35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.20(a), supplied and fitted to chowkats.
S&F for Aluminium anodised (powder coated) window and ventilator shutters, side hung type, without sash bars, aluminium section weighing not less than 0.55 Kg/Metre including clips, rubber packing aluminium snap beading, screws, fittings (each shutters) such as peg stays 150 mm long, hinge type B-21 100 mm long (2 Nos), 150mm long D type handle (one number) and tower bolt 150mm long (one number) Notes : (i) Glass panels to windows/ventilator shall be measured and paid for separately under respective item of this schedule as supply only. (ii) Thickness of powder (polyster) coating shall not be less than 50 Micron. (iii) Shade/tint of powder coating (epoxy polyster) shall be as approved by GE. (iv) Frame shall be measured and paid for separately under respective item of this schedule. (v) Quoted rate shall deem to include cost of alumiumum powder coated builder hard ware.
M & L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15) of approved design /Pattern, with approved standard section and fixed to the existing window frame with CP Brass stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. Notes:- (a) The rates include for provision of PVC protected sheeting and its removal after fabrication. (b) The work shall be measured and paid for net finished work of grid frame. (c) The rates shall also include for necessary notching and prepared holes. (d) The rates do not include for supporting hanger comprising of mild steel rod, J bolt with necessary washers, bolts and nuts, for securing frame work to ceiling and to the snap grid (e) The supporting hanger comprising of mild steel rod, bolts with necessary bolts, nuts and washers shall be measured
Supply only 4mm thick figured glass, pin head type not exc 0.5 sqm in each pane complete all as specified.
S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified.
S & F in repiars butt hinges mild steel cold rolled mild and fixed 100mm size, type C-22, extruded mild steel with mild steel hinge pin, anodised complete all as specified and as directed by the Engineer-in-Charge
S & F butt hinges alluminium alloy with galvanised mild steel hinge pin 75mm size, type C-22, complete all as specified and as directed by the Engineer-in-Charge
S & F 200mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed by the Engineer-in-Charge
S&F 100mm cast brass with mild steel bright polished type B-11 butt hinges, and fixed.
S&F 150mm long brass handle cast type polished handles and fitted.
S&F 300mm long brass sliding door bolt with sand and dry cast brass hasp staple bolt type and fixing bolt with rolled or drawn brass bolts and fixed complete.
S&F continuous (Piano) hinges of mild steel bright finish or electro-galvanised of 30mm flap width complete all as specified and directed by Engr In Charge
S&F for door eye viewer with 180/200degree wide view for peephole and fixed in wooden door shutter, complete all as specified and directed by Engr In Charge
S&F brass cupboard locks grade-I, 4 LEVER of size 65mm complete all as specifed and directed by Engr in Charge
S&F floor door stopper of brass body and 140mm with hard drawn steel spring complete all as specified and as directed by the Engineer-in-Charge
S & F wardrobe hooks (single) of size 50mm to 60mm, aluminium, complete all as specified and as directed by the Engineer-in-Charge
S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished complete all as specified and as directed by the Engineer-in-Charge
S&F in repairs for sheet glass 4.0mm thick, ordinary quality and glazing with oil putty in square not exceeeding 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge
S&F in repairs 20 to 25mm external dia drapery rods stainless steel with including designer lattos and brackets complete all as specified and approved by Engr In charge including taking out old pelmet with curtain rods all as directed.
S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified
S & F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples
M&L for preparing of new or previously painted wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-charge.
M & L for preparing of new untreated steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.
Taking down steel tubing and connections including removing from site of 15mm bore pipe complete all as specified and directed by Engineer-in-charge.
All as per Srl item No 56 above but 20mm bore.
S&F 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge.
All as per Srl item No 58 above but 20mm bore.
Cuttings chases for concealed water tubing of concealed conduit (cutting n.exc 10 cms girth) and making good in CM ( 1:3) in brick walls.
S&F in repair 25mm gate valves gun metal with iron wheel head screwed both ends for iron pipes complete all as specified.
Supply and fixed in repair Vitreous china wash down water closet (Pedestal Pattern) Cat Part No. S1051103 'P' or 'S' Trap 'CAMELIA' of "Cera" or equivalent white including closet seat, PVC flushing cistern 10 litre, flushing pipe, toilet paper holder, health faucet, PVC connection, Angular stop cock (valve) with flange etc complete all as specified and directed by Engineer in charge.
S&F brass chromium plated waste coupling 32mm bore for WHB complete all as specified.
Supply only 32mm bore and 60cm long PVC waste pipe for WHB/sink complete all as specified.
S&F 15 mm dia wash basin CP brass mixer for mixing hot and cold water as in repair complete.
S&F in repairs CP brass shower rose with swivel joint of size 125 mm suitable for 15 mm bore pipe complete all as specified.
S&F 15mm brass concealed stop cock quarter turn, fancy type ISI marked cast copper alloy, screw down high pressure with crutch or butterfly handle screwed both ends suitable for iron pipes of 15 mm bore complete all as specified.
S&F in repairs 15 mm dia wall bend mixer brass chromium plated fixed to existing pipe/connections including telephonic hand shower and all necessary fittings complete all as specified and directed by Engr In Charge
Supply fabrication & fixing in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc including taking down or and making good of disturbed surface all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370). Make- Jindal Section or as approved by GE.
S&F in repairs 15 mm bore bib taps quarter turn, ISI marked chromium plated and fancy type with crutch or butterfly handle high pressure screwed down for iron pipes complete all as specified.
S&F in repairs 15mm dia PVC Connection 600 mm long with 2 Nos brass check nuts suitable for 15 mm bore of pipe with washers complete all as specified.
S&F Heath faucet CP with 1.00 mtr long PVC pipe including necessary GI fittings as required like tee, nipple etc complete all as specified and directed.
S&F in repairs 600 x750 mm fancy type looking mirror designed as required at site as directed by Engr In Charge including all necessary fittings
S&F in repairs of glass shelf assembly consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long copmplete all as specified and directed.
Supply and fixed in repairs soap dish chromium plated brass fixed with brass nuts complete all as specified.
Supply and fixing CP Towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats all as specified
S&F 100 mm dia CI sand cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors/fixed to wall or dia in repairs complete all as specified and as directed by Engineer-in-Charge..
S/F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with stainless steel sink coupling of size 40mm dia all as specified and directed
S&F in repairs 20mm bore ball valve of PVC with rod and reducer of 20 to 25mm if required and polythene float complete all as specified.
S&F in repairs to rotational moulded vertical water storage tanks, three layered, white in colour, with closed tops (cylinderical) hoisted and fixed in position of 1000 ltr capacity including disconnecting and refixing the existing GI fitting and pipe complete all as specified and directed.
S&F in repairs to Rotational moulded polyethylene (three layered) water storage tanks, white in colour (Cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres all as specified in SSR Part-I.
M & L for 100mm bore dia cast iron floor trap with CP grating, including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed
S&F 110mm dia PVC SWR pipes(Type A) of pressure 6kgf/cm2 fixed complete to walls, ceilings, in floors etc including all necessary fitting arrangements and bends couplings etc as in rain water pipe complete all as specified and directed by Engr-In-Charge
S&F PVC (SWR) bends (Type A) of 110mm bore complete all as specified and directed by Engr-In-Charge
Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exceeding 100m but not exceeding 250m.
Demolition of Mud/mud phuska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.
M&L 25mm thick (average) PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in roof padding, benching existing roof slab laid to slope as per existing or as directed including finished surface even & fair complete all as specified and directed.
M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC shall be measured and paid separately.
Supplied only for liquid water proofing compound.
M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces
M&L for Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm.
M&L for One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions (iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or "MOPLY FP" of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units as per relevent IS.
Applying one coat of aluminium paint on top of APP membrane.
M&L preparation of newly plasterred surfaces of walls and applying three coats of white wash complete all as specified and directed.
M&L preparation of old decorated surfaces of ceilling, corinces, pillasters etc and applying two coat of white wash complete all as directed.
M&L for preparing of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.
S & F in repairs,Wash basins, vitreous china white (flat back or angle back type) of size 630 x 450mm, Including Pedestal/Leg excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32mm x 600mm long PVC waste pipe complete flange end bedded in red lead cement and other end fixed as in repair complete all as specified and directed by Engr-in-Charge. Make : Cera/Parryware/Hindware.
S&F in repair stainless steel plate rack of size 600x750x250mm weight not less than 7 kg each complete all as specified and directed by Engr-in-Charge
Supply and fix stainless steel (Grade S-304) basket (plain) of minimum size 50cm x 37cm x 10cm made of 4mm minimum dia S.S.Wire, thali basket (11-13 division) of minimum size 50cm x 37cm x 20cm made of 4mm minimum S.S.Wire, plate basket (11-13 division) of minimum size 50cm x 37cm x 16cm made of 4mm minimum dia S.S.Wire, Partition basket of minimum size 50cm x 37cm x 16cm made of 4mm minimum thick S.S.Wire, Cutlery basket of minimum size 50cm x 37cm x 10cm made of 4mm minimum dia S.S.Wire and bottom of S S Perforated sheet, bottle pullout of minimum size 50cm x 40cm x 16cm in two tier made of 4mm minimum dia S.S.Wire trolly with 4mm thick 304 grade 6 Nos attached with hinges & SS Handle & outer frame made with aluminium sections and cover with ACP Sheet (with choice colour), shelves inside the cabinets complete as per specifications and as directed by engineer-in-charge.
M&L for treatment of soil under existing floors using emulsion @ one litre per hole , 300mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 ( 1 cement : 2 coarse sand) to match the existing floors complete all as specifed and as directed
M&L for ATT along the external wall below concrete or masonry apron using chemical emulsion @2.25 litre per linear metre including drilling and plugging holes etc in apron
M&L for providing precast cement concrete of 1:2:4 type B 0 (using 12.5mm graded aggregate), louvers and jallies 25mm thick ( measured solid ) set in cement mortor 1:4, including all mouldings but excluding frames all as specifed and as directed
Taking down existing cement plaster of any description over damaged surfaces irregular facia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even ( avg 50mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate shall be provided wherever required) followed by 05mm thick rendering in CM (1:3) finished complete all as specified and directed including two coats of cement base paint over a coat of primer over new plaster surface including preparation etc complete after curing of specified time and drying the surfaces as required.
Preparing of previously painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge.
M & L preparing new plastered surfaces of walls and applying finishing the wall with acrylic smooth exterior paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm) complete all as specified.
M & L for complete removal of existing treatment and preparing old plastered surfaces of walls and finishing the wall with acrylic smooth exterior paint of required shade new work (two or more coat applied @ 1.67ltr/10Sqm and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm) complete all as specified.
M&L for preparation of newly plastered surfces of walls and applying two or more coats of distempering on new work with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer, of required shade and colour complete over a coat of wall care putty 3mm thick, as per manufacturer's specification.
Complete removal of existing treatment and preparing old plastered surfaces of walls and applying two or more coats of distempering on new work with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer, of required shade and colour complete over a coat of wall care putty 3mm thick, as per manufacturer's specification.
Preparation of newly plastered surfaces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick complete all as specified.
Complete removal of existing treatment and preparing old plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick complete all as specified.
Removing old tarfelt or polythene film including taking down plaster of sunken floor , roughening and cleaning by brushing with wire brush to remove all dirt and apply a coat of cement slurry with 3.00 Kg of cement per sqm and rendering 15mm thick in CM 1:3 using WPC finished rough (sunken floor/wall) and then applying two course treatment as follows :- (i) Applying bitumen primer @ 0.40Kg/Sqm (ii) Laying APP (Atactic polypropylene) modified membrance 3mm thick and weighting not less than 3 Kg/Sqm with 100 GSM/Sqm non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap. The membrane has to be laid with LPG torch and over lap sealed and finished neat.
S&F 100mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4) complete all as specified.
S&F 75mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4) complete all as specified.
Supplying ang laying UPVC Pipes (SCH-80) of 75MM fittings on walls/ceiling or laying in floors complete all as specified
Supplying ang laying UPVC Pipes (SCH-80) of 100MM fittings on walls/ceiling or laying in floors complete all as specified
Demolition and breaking up 150mm dia drain pipes (Salt glazed ware, AC or reinforced concrete ) set in cement mortar complete all as specified and directed by Engr in Charge.
Concrete bed to drain pipes laid in trenches including packing under and haunching against the sides of pipes aftaer they are laid and tested in cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate for 150mm bore pipe, complete all as specified and as directed by Engr in charge.
M & L for Salt -Glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as spd and directed
Cutting into existing manhole for connecting new drains and making good to pipes and rendering cutting out existing benching for and forming branching for and forming branch channel (1/2 round or ¼ section ) in PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate smooth finished and reforming benching as specified and directed for 150mm dia of pipe complete all as specified.
M&L for Plain cement concrete 1:2:4 type B-1( using 20mm graded aggregate) as in benching, coping including watering slightly rounded or chamfered angles and throating including necessary form work complete all as specified.
S & F 35mm thick plain framed panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered board with commercial veneering on both faces. The size of rail and stile (2nd class hard wood rail and stile) as per IS -1003 (Part-I) klin seasoned and chemically pressure treated complete all as specified and directed.
S & F 18/19 mm thick solid PVC board (Coloured or printed) as in cupboard shutters, partition walls and shelves fixed with frame complete all as specified and directed. Note:- Coloured choice as Per requirement of User and directed by Engr in Charge
M & L for 10mm thick joint free 'Endura cool roof (SRI) tile' in light shade, floor tiles (square/ rectangular) area of each tiles exc 0.06 sqm but n exc 0.11 sqm,in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.
S&F for CP fancy type 15mm bore stop valves/Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, and screwed both ends for iron pipe or for union. (ISI marked)
M & L for Vitreous china squatting pan “ORISSA” pattern size 630x450mm ( Make : Hindware) white with integral foot rests all as fixed in repairs including cast iron ‘P’ or ‘S’ trap 100mm bore including PVC low level cistern of 10 litres capacity including brackets jointing to flush pipe, PVC connection (600x15mm), flushing pipe complete fixed in repair all as directed by Engr-in-Charge.
Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custody for taking credit complete all as specified and as directed by Engineer-in-Charge
Taking down ceiling fan any sweep, removing blades ,cleaning the fan completely for dust and dirt as well as oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engineer-In-Charge.
Taking down existing energy meters, keeping aside safely & refixing the same in its original position after making functional & after completion of point wiring/sub main wiring, complete, all as specified and directed by Engr-In-Charge. Note:- Small items required for fixing the electric energy meter at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.
Taking down existing electric water heater, keeping aside safely & refixing the same to its original position after servicing of the whole geyser/making functional and after completion of wiring work, complete, all as specified and directed by Engr-In-Charge. Note: If any part found unserviceable during the refixing of water heater at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.
M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick bakalite laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following :-
(a) One light point controlled by one switch 5 Amp.
(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp
(c) One socket out let 5Amp controlled by one switch on same board.
(d) One socket out let 5 Amp controlled by one switch on independent board.
(e) One bell point 5 Amp controlled by one bell push on independent board.
(f) One light point controlled by two, 2way switchs5 Amp
All as per item No 130 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independent board.
All as per item No 130 here in before but point wiring with 4 sqmm FRLS multi stranded copper conductor cable for main circuit and 4 sqmm cable as earth continuity conductor for controlled by two pin and earth plug and socket complete with one single pole MCB 20 amp 240V
S & F Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified.
S & F Modular Bell push SP 5/6 A suitable for 1 Module complete all as specified.
S & F Modular socket 5 pin, 5/6 Amps suitable for 2 Module complete all as specified.
S & F Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified
S & F Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified.
S & F Modular Fan step Regulator electronic, 120 watts, 2 Module complete all as specified.
S & F Modular white cover plate including Modular base frame/boxes & powder coated Modular sheet metal concealed box for 6 module complete all as specified.
All as per Item No-145 above but 3 module complete all as specified.
All as per Item No-145 above but 2 module complete all as specified.
All as per Item No-145 above but 8 module complete all as specified.
All as per Item No-145 above but 12 module complete all as specified.
S & F Modular blanking plates 1 module complete all as specified.
S & F in replacement, electric bell ding ding 230V AC complete all as specified.
Supply and fixing LED light fitting 1 x 18W, 220V, AC decorative box type with driver, holder including LED tube light andconnecting up with three flexible copper conductor cable of suitable size from ceiling rose complete.
Supply and fixing LED light fitting 1 x 9W/ 1 x 10W bulk head luminaires with driver, holder including LED light and connecting up with three flexible copper conductor cable of suitable size from ceiling rose complete.
Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watt, 220V AC decorative type with driver, holder including LED tube light and connecting up with three flexible copper conductor cable of suitable size from ceiling rose complete.
Supply and fixing ceiling fan complete with blades, down rods, electronic regulator and accessories, 230V, 1200 mm sweep, minimum air delivery 210 CFM with service value 6.00, BEE 5 star rated with brushless direct current motor (BLDC) compatible conventional fan regulator, single phase AC 230/240V complete incl grouting of eyebolt of suitable size in ceiling and fixing the fan by mean of suitable bolts, nuts, washers and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to fan complete.
Supply and fixing swing type wall mounting fan 450 mm sweep single phase AC 230/240V complete for wall mounting including grouting, holding down bolts, nuts, and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to fan complete.
Supply & fixing heavy duty PVC Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers
Supply & fixing heavy duty metal body Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers
S&F Single pole & neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp 240V complete all as specified.
S&F LED sleek surface round ceiling mounted decorative down light fitting with PC cover suitable for 1x12 watt complete all as specified and directed.
S&F decorative wall mounted luminaire with and including 9 watt LED lamp complete all as specified and directed.
S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings including 7 Watt LED bulb complete all as specified and directed.
S&F MCB single pole 6 to 32 Amps 10 KA 230 volts "C" series complete
S&F MCCB 125A 4Pole 16KA 415 Volt with fixed magnetic and fixed thermal setting complete.
S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar compatible for 125 A MCCB as incomer 16 KA complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site including taking out of existing unserviceable DB with MCBs.
M&L for sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6.0 sq mm as earth continuity conductor connected to commen earth and earth dolly complete including taking out existing unserviceable service connections.
Note:- Schedule of credit Rs. 1,06,482.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.
bamral builder
R.K. Works
M/S Jasbir Singh
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .