Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹44.6 LAccepted-AOC AMLA TOLA DISTT KATIHAR BIHAR 854105 | KATIHAR | BIHAR | 854105 | L1 | Accepted-AOC Being lowest bidder and reasonable | |
| 2 | L2₹47.9 L+₹2.7 L (6.09%)Rejected-Finance | L2 | Rejected-Finance Other than lowest | |
| 3 | L3₹60.2 L+₹15.1 L (33.3%)Rejected-Finance TIORKHALI MAHESHGANJ NADIA | NADIA | NADIA | WEST BENGAL | 790804 | L3 | Rejected-Finance Other than lowest | |
| 4 | L4₹61.4 L+₹16.3 L (36.1%)Rejected-Finance PO CHANDL PS BISHNUPUR DIST SOUTH 24 PGS PIN 743503 | 24 PARAGANAS SOUTH | WEST BENGAL | 743503 | L4 | Rejected-Finance Other than lowest |
Tender Value
₹44.5 L
EMD Value
₹89,000
Closing Date
14 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE(FW) Kolkata
D9 Commissariat Road Hastings Kolkata 700022
ADDN/ALTN AND RENOVATION OF JOINERIES OF CERTAIN OFFICES INCL CONNECTED WORK IN BLDG NO P-1 AND PROVN OF ROAD SIDE CURB STONE AND CONNECTED WORK AT VARIOUS LOCATIONS INSIDE FORT WILLIAM UNDER GE (FW) KOLKATA
2022_MES_559723_3
8935/FW/E8
Open Tender
Civil Works
Item Rate
180 days
GE(FW) Kolkata
Ref tender Documents
7 documents required · 7 mandatory
₹500
GE(FW) Kolkata
₹89,000
13 Jan 2023
30 Nov 2022
15 Dec 2022
30 Nov 2022
14 Dec 2022
30 Nov 2022
Amount
Taking down steel window frames not exc 1.5 sqm each but with shutters (without taking off shutters from the frame) and removing from the site complete all as specified and directed.
Taking down steel window frames exc 1.5 sqm each but not exceeding 4 sqm each and removing from the site complete all as specified and directed.
Taking down aluminium frame with shutters of any description not exc 1.5 sqm each and removing from the site complete all as specified and directed.
Taking down aluminium frame with shutters exc 1.5 sqm each but not exceeding 4 sqm each and removing from the site complete all as specified and directed.
Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 150 mm thickness (above or below ground level) complete all as specified and directed.
Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.
Demolition of brick work or stone boulder masonry built in cement mortar including all quaries, arches pillars etc and removing debris off the site complete all as specified and directed.
Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches of 100 mm internal dia complete all as specified and as directed.
All as per Item No. 08 above, but for 150 mm bore pipes
S&F powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge.
S&F 5mm thick toughened glass as in hinge doors, partitions, windows, automatic doors and similar works including cutting to shape, drilling holes as required complete all as specified and as directed by Engineer-in-Charge.
M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregates in foundation filling and mass concrete complete all as specified and directed.
M&L for brickwork with fly-ash old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.
M& L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.
M&L for dubbing out cement plaster (1:4), average 20 mm thick on irregular faces of walls (when specially ordered in writing) complete all as a specified and as directed
M&L for rendering 15 mm thick to fair faces of brick work / concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.
M & L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with water proofing compound (@ 200 ml per bag of cement or as per manufacturer's instructions) on brick/stone walls or concrete surfaces finished even and fair (upto any height) for external surfaces complete all as specified and directed. Note : Water Proofing compound shall be measured and paid separately as "Supply only"
Supply only liquid Water Proofing Compound, conforming to IS and as approved, complete all as specified.
S&F rectangular and curved factory made uPVC fixed windows with frame dimension of 58mm x 52mm x 33mm for windows with corners fusion welded, fully reinforced with Galvanized steel of 1.2mm . The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should have extrusion facility in India and the windows to be assembled and installed by an authorised local fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and also scaffolding if required for fixing is deemed to include in the rate quoted complete all as specified and directed.
Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.
S&F factory made uPVC- Sliding windows/doors having three tracks and three sashes (shutters) with frame dimension of 104mm x 49mm and sash dimension of 61mm x 47mm x 37mm each with middle sash fixed ,fixing of powder coated grill with and including upvc beading of required size, with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm. The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in 1st quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles having a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed.
Note: The unit rate quoted by contractor excludes cost of glass and powder coated aluminium grill and includes all other connected accessories. Net opening will be measured for payment purpose. Glass and powder coated aluminium grill will be measured and paid separately under respective items.
S&F factory made uPVC- Sliding windows/doors having two tracks and two sashes (shutters) with frame dimension of 58mm x 49mm and sash dimension of 61mm x 47mm x 37mm with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm.The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer shall have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. The profiles shall have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed.
Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.
M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) with joints to match complete all as specified and as directed.
M&L for preparation of new surfaces of walls including cleaning, watering to make the surface clean and free from dust and applying 2 mm thick wall care putty for smooth finish and applying two coats of acrylic distemper, finished with rollers over a coat of alkali resistant primer complete all as specified and directed.
M&L for preparation of newly plastered surfaces and applying two coats of exterior acrylic emulsion weather proof paint over a coat of primer to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufactuirer's instructions, with and including 2mm thick exterior wall care putty complete all as specified and as directed.
M&L for applying one coat of acrylic distemper, finished with rollers to old decorated surfaces of walls including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.
M&L for preparing new plastered surfaces of walls and applying two coats of cement base paint with brush over a coat of alkali resistant primer complete all as specified and as directed.
M&L for preparation of old decorated surfaces and applying one coat of weather proof exterior acrylic emulsion paint to old decorated surfaces of walls of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, upto 6 storey height complete all as specified and as directed.
M&L Preparing old Steel Surfaces of any description not otherwise described over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint, complete all as specified and as directed.
S&F Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified, fixed on walls complete all as specified and directed.
All as per Item No.30 above, but for 150 mm bore pipes
S&F CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.
S&F 100 mm bore cast iron (sand cast) bends with access door (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed by the Engineer-in-Charge.
S&F Cast Iron Branch Piece 100mm bore (dia) single (equal or unequal), ordinary or inverted (spigot or socket type) with Parallel Branches fitted with Oval Access Door including Jointing with Cement Mortar 1:1, fixed complete all as specified and directed.
S&F CI bends for 150mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.
S&F Cast Iron Branch Piece 150mm bore (dia) single (equal or unequal), ordinary or inverted (spigot or socket type) with Parallel Branches fitted with Oval Access Door including Jointing with Cement Mortar 1:1, fixed complete all as specified and directed.
S&F Stack clamps for 100 mm dia bore pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, as in repairs, complete all as specified and directed.
S&F Stack clamps for 150 mm dia bore pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, as in repairs, complete all as specified and directed.
Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and directed.
Excavation in trenches n exc 1.50 m wide and n exc 1.50m depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes etc not exc 10 Sqm on plan and not exc. 1.50 Metre in depth and getting out as in soft/loose Soil, complete all as Specified and as directed.
Returning filling in incl spreading , levelling , watering and well ramming in layers not exc 25 cm as in soft/ loose Soil, complete all as Specified and as directed.
Removing excavated materials not exc 50 m and depositing where directed at a level not exc 1.50 m above the starting point complete all as Specified and as directed.
M&L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.
M&L for providing 100 mm thick, Plain Cement Concrete (1:4:8) type D2 using 40mm graded stone aggregate as in footpath, sub base of floor, hardstanding etc complete all as specified and directed.
M&L cement concrete type C2 (1:3:6) using 40 mm graded stone aggregate, 75 mm thick as in plinth protection, laid in alternate bays, finished even and smooth without using extra cement, complete all as specified and directed.
Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A'
M&L for 50mm thick PCC 1:2:4 type B-2, using 40mm graded stone aggregate, as in floor, path etc, finished even and smooth without using extra cement complete all as specified and directed.
Supply and laying 60mm thick factory made chamfered edge precast glazed cement concrete paver block of M-50 grade confirming to IS 15658-2006 with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)
S&F in position, at or near ground level, factory made precast cement concrete kerb stone blocks, in M-25 grade cement concrete, fixed to the required line, level and curvature, jointed in cement mortar 1:3, including making joints with or without grooves (thickness of joints, except at sharp curves shall not be more than 5 mm) including making drainage opening wherever required complete all as specified and directed.
M&L for heavy duty ceramic floor /paving tiles of size 300 x 300 x10mm thick in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. (MAKE : JOHNSON, Model : Endura or equivalent item in other makes listed in the tender)
S&F RCPC (Reinforced Cement Polymer Concrete) grating slab of size 1200 mm x 450 mm x 75 mm thick, of Capacity 5 MT fixed in proper position complete as directed by Engr-in -Charge.
S&F RCPC (Reinforced Cement Polymer Concrete) grating slab of size 900 mm x 450 mm x 75 mm thick, of Capacity 5 MT fixed in proper position complete as directed by Engr-in -Charge.
S&F RCPC (Reinforced Cement Polymer Concrete) grating slab of size 600 mm x 450 mm x 75 mm thick, of Capacity 3 MT fixed in proper position complete as directed by Engr-in -Charge.
M&L Mild steel framed work such as grills of ornamental type, gratings, etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works incl portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc confirming to grade Fe-290. Gde-E-165, complete all as specified and directed.
S&F Cast iron work grade FG -150 unmachined in brackets, gratings, railing, frames, manhole covers and similar articles exc 5 Kg each complete all as specified and as directed.
M&L welded steel wire fabric, weight n exc 4 kg per square meter complete , fixed to steel members, all as specified and directed.
Cutting holes in brick walls in cement mortar for inserting holdfast or pipes and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick, etc complete all as specified and directed.
Dismantling wrought iron or mild steel work of any description not other wise provided for., complete all as specified and directed.
M&L for glazed ceramic coloured tiles of size 350x250x 7mm/450x 300 x 7 mm thick as on vertical surfaces such as wall, dado, skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over 10 mm thick CM 1:3 backing coat complete all as specified and as directed.
S&F 110 mm bore PVC (SWR) pipes, type 'A', single socketed in any length with rubber ring joints, laid in trenches or under floors complete all as specified and directed.
M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.
M&L for two coats of synthetic enamel paint over a coat of primer to concrete or plastered surfaces, plain or moulded n.exc 10 cm width or girth including preparation of surface all as specified and as directed.
Adamya Group Of Company
SHEIKH ENTERPRISE
UNITED ENGINEERS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .