Construction of Panchayat Office in Thirumalakolunthupuram Panchayat in Palayamkottai Panchayat union.

Amount

Construction of Panchayat Office in Thirumalakolunthupuram Panchayat in Palayamkottai Panchayat union.

Earthwork excavation for foundation in all soils and sub-soils to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring, strutting and baling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of not more than 15 cm. thick well rammed and consolidated and depositing the surplus earth in all places shown by the departmental officers with initial leads and lifts, etc., including levelling the sites complete complying with standard specifcations and as directed.

Filling in foundation and basement with M sand in layer of not more than 15cm thick including all charges etc.complete

Refilling in foundation and basement with excavated eartth in layer of not more than 15cm thick including all charges etc.complete

Cement concrete 1:4:8 mix using 40mm guage hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc.,complete complying with standard specifications and as directed.

Brick Work in CM 1:5 mix using country bricks ground moulded of size 83/4"x41/4"x21/4" for the following including curing etc., complete

Brick Work in CM 1:5 mix using country bricks ground moulded of size 83/4"x41/4"x21/4" for the following including curing etc., complete

Centering above G.L : Supplying and erecting centering shuttering including necessary supports for the plane surgace in foundation and basement and in all floors for RCC column footing column plinth beam, beams, roof slab, slaircase steps, bed blocks,critical pier etc.,

Below Ground Level

Above Ground Level

Supplying and fabrication of steel for RCC items including cost and conveyance of all materials and labour charges etc complete

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350KG/M3 and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of Sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350KG/M3 and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of Sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete.

Plastering with cement mortar 1:5,12mm thick and including the cost and conveyance of all materials and all labour charges etc.,complete. complying with standard specifications and as directed.

Weathering course concrete using best quality broken brick jelly of size 20mm uniform guage in pure slaked lime (no sand to be used)over the RCC roof slab in the proportion of brick jelly to lime being 32:12:5 by volume and laid over in a single layer and consolidated to the required designed and finished thickness beating the concrete with wooden beaters of approved pattern ,keeping the surface constantly wetted by sprinkling lime jaggery water as per standard specifications etc., complete as directed by the departmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 23cm x 23cm x 20mm of approved quality laid in cement mortar 1:3,12mm thick mixed with water proofing compound confirming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar ,red oxide etc., complete complying with standard specifications.

Paving the floor with best quality Stain free Nano Polish Vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.

Paving the floor with Cement Based Hyd Pressed Anti Skid (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Dadoing the walls with new Glazed tiles of size 150 x150 x6 mm laid in CM 1:2 ,10 mm thick and pointig with white cement using 0.40 Kg/m2 including finishing the joint and pointing flush with ties surface

Providing granolithic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete

Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and approved colour over a priming coat including through scrapping, clean removal of dirt and including necessary plaster of pairs putty, wherever required etc complete complying with standard specification

Painting two coats over new iron works using ready mixed enamel paint including cost and conveyance of paint and all labour charges etc complete

Fabrication and supply of Mild Steel Door of any size with single leaf outer frame made of 35x35x5 mm equal M.S angle and shutter frame made of 25x25x5 mm M.S angle for horizontal and vertical member with stiffener and fully covered with 18 G plate etc complete.

ROLLING SHUTTER (SOR M-0404)

GRILL GATE (1.20x2.10m)

Fabrication and supply of Mild Steel Window of any size with single leaf outer frame,mullion section made of 35x35x5 mm equal M.S angle and shutter frame made of 25x25x5 mm M.S angle for horizontal and vertical member with stiffener and fully covered with 18 G plate etc complete.

steel window W (1.50x1.30m)

window W1(1.50X1.30M)

Supplying & fixing with cuddapah slabs 20-30mm thick for cup board thick and pointed with cement mortar 1:3

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone M.Sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone M.Sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm P or S trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and redoing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting SOR M-0647

Supplying and fixing P.V.C rainwater down fall pipe of 110mm dia

Supplying and fixing of Bevelled Edge Mirror of size 600x450mm with ply wood back and aluminum beading complete complying with standard specification

Provision for Manhole cover for septic tank, etc., complete.

Provision for Water Supply Arrangements

Drilling of 150 mm dia deep bore well in hard rock area(Outer Pipe Length) including labour charges and transportation charges

Drilling of 150 mm dia deep bore well in hard rock area including labour charges and transportation charges

Supply and Delivery of 150mm dia 6KSC Casing Pipe

Supply and Delivery of Three SINGLE Submersibble 1Hp Motor 30x125 including all cost and Labour Charges etc complete

Supply and delivery of single phase 1HP Pannel Board

Supply and delivery of 32mm UPVC Pipe

Supply and delivery of 2.5 sqmm 3 core copper cable

Supply and delivery of 1000lit. Capacity HDPE tank As per IS 12701/1996

Labour charges for erection of new submersible pump set in the bore well and commissioning

Supply and delivery of 32mm PVC pipe etc. complete.

Provision for Electrical Arrangements

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3 mm thick Hylum sheet cover with TW box And 5 A FT switch with continuous earth connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC Open Light point / fan point (For electronic Regulator) SD 24

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 mm X 100 mm X 113 mm TW switch box with 3 mm thick Hylum sheet cover for 5 A 3 pin non interlocking CS plug with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for concealed PVC plug point SD 37

Supply and run of 2 of 4sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7/20 Gibearer wire for service connection mains SD 65

Supply and run of 2 of 4sq.mm. PVC insulated SC unsheathed FRLS copper Conductor of 1100 V grade in 25 mm dia GI pipe ( Class ' B ' ) suitably bend at both ends with necessary angle iron upright and end supports for mains. SD 70

Supply and fixing of WT bulk head fitting suitable with guard and 15 W (100W) LED bulb SD 85

Supply and fixing of fancy glass shade and 15 W LED Bulb SD 80

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals tot he fitting with tube SD 88

Supply and fixing of 1200 mm ( 48") AC ceiling fan complete with stepped electronic 300 W regulator with 300 mm down rod on the existing clamp. SD 112

Supply and fixing of TNEB Meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1No 40Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection SD 125

Supply and fixing of 15A aerial fuse unit (500A) on suitable100x100mm TW concealed box with hylem shee ton the tapping pole with necessary clamp. SD 130

Earthing asper the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not lessthan 40mm with copper earthplate of size125mmx50mmx6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. SD 221

Supply and fixing of 16A TPN metal clad switch on suitable angle iron frame work with MS cable entry boxes with earth connection only SD 146

MADASAMY (BID ID -1563940)