PROVN OF LADIES AND GENTS TOILET BLOCK AT BUDDHA CHOWK ALONGWITH CERTAIN OTHER SPL REPAIR, REVENUE AND MINOR WORKS AT JAIPUR MIL STN

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for RCC M-25 (Design Mix) (using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, under reamed piles and mass concrete complete all as specified and as directed Note : Reinforcement & formwork shall be measured and paid for separately.

M&L for RCC M-25 (design mix) (using 20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

M & L for RCC M-25 (Design Mix) (using 20mm graded stone aggregate) as in slab supported on walls , beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

M & L for RCC M-25 (Design Mix) (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed Note : Reinforcement & formwork shall be measured and paid for separately.

M&L Mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed and specified.

,--- ditto--- all as per srl item No. 16 above but TMT bar of 6 to 8mm dia complete all as directed and specified.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparing new plastered surfaces of wall etc and applying two coats of cement base paint in plain patterns over a coat of alkali resistant priming paint all as specified and as directed

M&L for 100 mm thick PCC 1:4:8, type D-2(40mm graded aggregate) as in sub base complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

M&L screed plaster 15mm thick in cement mortar (1:4) on concrete surfaces of roof to receive water proofing treatment and finished the surface even and smooth without using extra cement etc incl mixing of WPC as per manufacturers instruction complete all as specified and directed. Note:- Integral water proofing compound paid seperately as supply only

M&L for painted surfaces of roof with one coat of cold applied bituminous primer @ 0.40 ltr/Sqm conforming to IS-33894 and laying APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5kg/sqm, reinforced with polyester non woven fabric (weighing not less than 150gms/sqm). Application of polymeric membrane shall be laid by torch application. Side over laps shall be 75mm and the end lap shall be 100mm and all over laps and joints shall be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing. Note: (i) Work shall be carried out through authorized applicator only

S & F vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S' trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed.

M&L for concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 150mm dia incl. packing under and hanching against the side of pipes after laying and testing of pipe complete all as specified and directed.

Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Disconnecting existing tank of capacity exc 250 and not exc 500 litre, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required, reconnecting and re-fixing in position including cleaning and removing all scale and dirt etc from service tanks and from mouths of circulating pipe etc, date of cleaning also mentioned on tank by synthetic enamel paint complete all as specified and directed. Note : Cleaning etc shall be included under this item only

Dismantling old unserviceable RCC / PVC water tank of cap exc 250ltr & n exc 500 ltr and removal from site complete all as directed

S&F rolled mild steel work as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the lenght indicated) and similar work, conforming to Fe-410W (Gde E-250) quality A complete all as specified and as directed.

Dismantling of stone set patti as in roof slab provided below roof slab of any desc and any thickness laid bedded and pointed in any mortar complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L sand filling under floors or in foundations including watering, spreading and levelling in layers of 25 mm thick complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as pe

Dismantling galvanised chain link fencing of any description fixed to any type of fencing posts incl line wires complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

S & F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and incl either hooks and pintal hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete confirming to Fe-290 Gde-E-165 complete all as specified and directed

M&L providing cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) in lintels up to 1.5m clear span, cills, bed plates,coping, kerbs water trough & the like including weathering, slightly rounded or chamfered angles & throating complete as specified and directed

M&L for preparation of newly plastered surface of walls and applying two coats of premium acrylic exterior emulsion paint, 1st quality (company depot tinted) of approved manufacturers in required colour and shade using hand roller over and including one coat of alkali resistant priming paints complete all as specified and directed .

S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment and well finished edges conforming to Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

S & F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. Note : Each line wire to be measured

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways;drainage crossings, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets ( for securing chain link fencing ) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Fixing only mild steel galvanized chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire complete all as specified and directed. Note :- Supply only chain link fencing shall be measured and paid for separately.

Supply only mild steel galvanized chain link fencing 4mm dia of mesh wire, mesh size 100x100mm including line wires complete all as specified and as directed.

S&F in repair mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation board/ slab/blankets any thicknesss including cover filletes complete all as specified and directed

Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Dune Tegular 24 Edge Tiles of 16mm thickness and Prelude 24mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.5 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with Board edge in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of up to 41%. The tile shall comply with Indoor Air Comfort Gold requirements, version 7.0 (2020) and this certification shall ensure compliance with LEED & DGNB, French VOC class A+, French HQE certification, German Regulation (AgBB/ABG), Italian CAM Edilizia, BREEAM International NOR NL, WELL Building, SKA Rating, BVB (Sweden), Eco Product Norway, Blue Angel DE-UZ 132, M1, Danish Indoor Climate Label, Singapore Green Label and GreenTag Australia. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. SUSPENSION: The tile shall be laid on KCS Prelude 38 with 24 mm wide T - section flanges colour global white (matching to tile colour) having roll formed double stroke rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 15 kg/m2 (as per standard installation layout mentioned below)

and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 18kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications above) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be KCS wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per recommended procedure. SUSPENSION SYSTEM accessories supplied by consisting of M6 Anchor Fasteners with hanger hole, pre-straightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners).

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc 5cm long and dia of neck 5 to 10 mm complete all as specified

M & L anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading, screws top & bottom pivot/ hinges etc. complete all as specified and directed.

M & L anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for solar control film 25micron reflective type sticked to glass panes as per instruction of manufaturer complete all as specified and as directed by Engineer in Charge. .

S&F 5.5 mm thick sheet glass, odinary quality and glazing with neoprene beading in aluminium window and door in square exc 0.5 Sqm in each pane complete all as specified and directed.

S&F Pressed steel frames of size 105 mm x 60 mm made of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia threshold bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) complete all as specified and as directed.

S&F Factory made 25 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Each Set

Per 1000 Nos

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

S&F Solid PVC Wall Lining (Panelling) consisting of 5mm thick coloured or textured PVC sheet fixed to PVC filet frame with screws inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing including refixing all fittings on surface after panelling work complete all as specified and directed

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing in SSR complete all as specified and directed

M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators, Partition section with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, sliding type, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each d

oor, hinges,anodised aluminum snap beading, screws top & bottom pivot/ hinges etc. complete all as specified and directed.

M&L for 09 mm thick prelaminated particle board interior grade, prelaminated both side with decorative choice lamination fixed with screw complete all as specified and directed.

S&F Door closer aluminium anodised extruded section body, hydraulically regulated designation No-3, universal type, suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

S&F mild steel mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified and as directed.

S & F 75mm (overall size of cover plate) size floor door stoper of aluminium alloy body and tongue, anodised, with double pin and rubber shoe fixed in bottom of door shutter complete all as specified and as directed.

S&F 6mm thick laminated toughened glass for structural glazing fixed with and incl silicon complete all as specified and as directed.

M&L preparation of newly plastered surfaces of wall & applying applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & as directed.

M&L for 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate) as in flooring and all other similar works finished even and fair complete all as specified and directed.

S & F 18 mm thick HDHMR (High density high moisture resistant) board one side white laminate and other side decorative as in Sink/ Wash Basin cabinets fixed with minifix hardware where ever required including edge band 22 mm wide 0.80 m thick of matching colour on exposed surfaces of board fixed with polymaster adhessive including trimming edges of edge band to true line of thicknesss of board by manual trimmer complete all as specified and directed.

S & F 8 mm thick HDHMR (High density high moisture resistant) board of one side white laminate and other side un decorative as in back of kitchen cabinets complete all as specified and directed..

S & F auto close hinges, stainless steel of grade SS-304, bright finish and fixed complete all as specified. Make : Godrej, Hindware, Lifetime, Hettich or equivalent

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and as directed.

S & F 150mm long stainless steel (Grade SS-304) barrel tower bolts and fixed complete all as specified & as directed.

S & F 250mm long stainless steel sliding door bolt, plate type, not less than 12mm dia with & including a min of six bolt & nut, four on bolt plate & two on staple plate and fixed complete as directed and specified.

S & F stainless steel handles of size 150 mm fancy type of approved make and fixed complete all as specified & directed.

S&F 25 mm dia steel water tubing, galvanized, medium grade, with all fittings, laid in trenches complete all as specified and directed by Engineer-in-Charge

S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

S&F 5.5 mm thick sheet glass, odinary quality and glazing with neoprene beading in aluminium window and door in square nexc 0.5 Sqm in each pane complete all as specified and directed.

S&F rubber gasket suitable to hold the glass and aluminium composite panel in aluminium partition work and provide a aweather tight seal complete all as specified and directed.

M & L for 4-5mm thick Aluminium composite panel, both side decorative (same colour) of an colour matching with aluminium partition work incl necessary shade of panel match with aluminium frame complete all as specified and directed by EIC.

S&F galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised steel wire staples in window or door complete all as specified and as directed.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

M&L for cutting, threading, drilling hole in existing CI/GI pipe line of size 80/100mm and making arrangement for tapping water connections for 25mm dia GI tubing complete with GI socket, clamp, nipple and all other accessories reqd and making leak prroof connection complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

M&L for boring of existing road / path for laying of GI pipe under road including making good disturbed areas with PCC 1:2:4 complete all as specified and as directed

S&F modular switch, 6 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket, 6 Amps, 2/3 pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket, 6/16 Amps, 2/3pin combined, 2 module AC 240 volts complete all as specified and directed.

M&L for Construction to brick masonary valve pit/ chamber of size 900x600x600 mm and including Brick work, Plaster in CM 1:6 on inside and outside (above ground), angle iron frame 40x40x6mm size including fabrication work, hold fast, MS sheet cover 3mm thick, duly painted with two coat of black bituminous paint of approved quality over a coat of red oxide primer, handle and including provn locking arrangement incl necessary earth work complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one socket outlet 16 Amps on independent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 4 sq

mm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one socket outlet 16 Amps on independent board or for 20amp single pole sockect outlet complete all as specified and directed.

S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed

S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity including connecting up complete all as specified and directed.

S&F modular bell push, 6 Amp, 1 module complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed.

S&F LED bulk head light fitting 9 watt IP 66 & IK 09 with with pressure die cast aluminium housing & polycarbonate diffuser duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed.

S&F door bell AC 240 volts, single pole complete all as specified and directed.

S&F MCBs Distribution board SPN, 8 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCBs and MCB DB shall be of the same make.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire size 4.0mm upto 7.5 m included in the item).

S&F MCBs Distribution board tripple pole and neutral (VTPN) 4 ways, powder coated, CRCA steel sheet, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 250 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCCB, MCBs and MCB DB shall be of the same make.

S&F MCBs of 'B' curve, single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'B' curve, Double pole 40 to 63 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

M & L Sand cushioning to under ground cable with screened and washed sand (non cohessive), 8 cm before laying cable and 15cm after laying and punned to 18cm after laying of cable complete all as specified and directed by Engineer-in-Charge. Note : Punned thickness shall be considered for payment purpose.

M & L bricks for protection cover to UG cable (with old size sub class B bricks, designation 75) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

S & F LED building street light fitting 35 watt 230V AC outdoor type comprising of pre wired driver, pressure die cast powder coated aluminium housing heat resistant glass, impact and corrosion resistance incl thermal management in multiple optics, clear acrylic cover and accessories with IP 65/66 protection complete all as specified and directed by Engineer-in-charge

S&F exhaust fan, high speed, steel body 250mm sweep, 1400 RPM, four blade, heavy duty motor, copper wound double ball bearings, grey colour with louver, nuts, bolts and washers incl three core 0.75sqmm copper cable connection with protective steel bird guard fixed in wall including making suitable size opening and making good the disturbed portion as per existing complete all as specified & directed.

S & F PVC Vanishing window blind open and close verticaly or horizonatly with the help adjustment rope on tube (roller), madeup of good fabrick, plastic or other good material best locally available in market including all necessary assesories for installation and making good the surface complete all as specified and directed.

S & F 20amp, single pole and neutral socket outlet, with 2 pole and earth, metal enclosed plug top in powder coated CRCA steel sheet enclosure recess mounted with chained matel cover for socket out let with and incl one single pole B curve MCB 20 Amps complete all as specified and directed.

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE, incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

M&L for taking out ceiling fan 1200mm sweep 50Hz AC 230 volts and refixing at new location including minor repair and replacement of fan blade, down rod, nut, bolt and washer and spray painting in existing colour including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required and writing MES No. on fan body complete all as specified and directed.

Supply, laying, jointing, testing & commissioning LT under ground cable XLPE insulated, screened PVC sheathed, galvanised steel strips or wire armoured, heavy duty electric cable with multi stranded aluminium conductor, 1100 volts grade cross sectional area 16sqmm, 2core confirming to IS:7098 (part-I), laid in trenches, ducts, pipes or fixed on poles or walls including all necessary clamps, nut, bolt, washers, saddle etc complete all as specfied and directed. Note : The cost of AI thimbles / lugs and cable gland etc is included in quoted raes.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ