Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹30.0 LAccepted-AOC | L1 | Accepted-AOC L1 | |
| 2 | L2₹31.5 L+₹59,580 (1.93%)Rejected-Finance | L2 | Rejected-Finance Rejected due to not L1 | |
| 3 | L3₹36.5 L+₹5.6 L (18.2%)Rejected-Finance 1273 CUTINO ROAD KARWAR 581301 | KARWAR | UTTARA KANNADA | KARNATAKA | 581301 | L3 | Rejected-Finance Rejected due to not L1 |
Tender Value
Refer Docs
EMD Value
₹74,000
Closing Date
29 Jul 2021, 6:00 pmClosed
GE(SB) Karwar
GE (Seabird) Karwar Naval Base Karwar
REPAIR AND MAINTENANCE OF EXTERNAL WATER SUPPLY DISTRIBUTION SYSTEM UPTO AND INCLUDING WATER METER IN KADAMBAVANAM AND CORE AREA AT NAVAL BASE KARWAR UNDER GE(SB) KARWAR
2021_MES_456139_1
8801/E8
Open Tender
Civil Works
Item Rate
330 days
GE (Seabird) Karwar Naval Base Karwar
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
GE(Seabird) Karwar
₹74,000
Yes
18 Sept 2021
1 Jul 2021
31 Jul 2021
1 Jul 2021
29 Jul 2021
15 Jul 2021
Amount
Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft / loose soil for laying/taking out GI pipe line all as specified and directed.
Returning filling in including spreading levelling watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil all as specified and directed.
Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.
Taking out old unserviceable PVC/UPVC/CPVC pipe with all fittings from ceiling, walls, floors etc of following sizes all as directed (Excavation & earth work will be measured & paid seperately under respective item):-
(a) 50 mm bore
(b) 40 mm bore
(c) 25 mm bore
Supply and laying CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings on walls, ceiling, roof or trenches all as specified and directed for the following sizes (Excavation & earth work will be measured & paid seperately under respective item):-
(a) 50 mm bore
(b) 40 mm bore
(c) 25 mm bore
Taking out old unserviceable GI tubing with all fittings from trenches, walls, floors etc of following sizes all as directed (Excavation & earth work will be measured & paid seperately under respective item) :-
(a) 100 mm bore
(b) 80 mm bore
(c) 50 mm bore
(d) 40 mm bore
(e) 25 mm bore
Laying only in new or old position in walls and floors GI tubing obtained from item No 6.03 to 6.05 here-in-before including cleaning of pipe including replacement of unserviceable fittings such as bends, elbwos, tees, sockets etc all as directed by Engr-in-Charge of following size (Fittings required shall be provided by the contractor. Unit rate quoted shall be deemed to include for the same):-
(a) 50 mm bore
(b) 40 mm bore
(c) 25 mm bore
Laying only in new or old position in trenches GI tubing obtained from item No 6.01 to 6.04 here-in-before including cleaning of pipe including replacement of unserviceable fittings such as bends, elbwos, tees, sockets etc all as directed by Engr-in-Charge of following size (Fittings required shall be provided by the contractor. Unit rate quoted shall be deemed to include for the same. Excavation & earth work will be measured & paid seperately under respective item):-
(a) 100 mm bore
(b) 80 mm bore
(c) 50 mm bore
(d) 40 mm bore
Supply and fix in repairs GI tubing medium grade galvanised with all fittings and laid in walls, roof, ceiling or laid in floors etc all as specified and directed for the following sizes:-
(a) 50 mm bore
(b) 40 mm bore
(c) 25 mm bore
Supply and fix in repairs GI tubing medium grade galvanised with all fittings and laid in trenches all as specified and directed for the following sizes (Excavation & earth work will be measured & paid seperately under respective item):-
(a) 100 mm bore
(b) 80 mm bore
(c) 50 mm bore
(d) 40 mm bore
Supply and fix in repairs gun metal gate valve ISI marked with iron wheel head screwed both ends for iron pipe of the following sizes all as specified and directed:-
(a) 50 mm bore
(b) 40 mm bore
(c) 25 mm bore
Supply and fix in repairs ball valve high pressure of PTMT with epoxy coated aluminium/stainless steel rod & high density plastic ball screwed for iron pipe of 25 mm bore (Minimum weight- 455 gms).
M & L for removing all scale and dirt etc from PVC tanks and from mouths of circulating pipes etc and cleaning tank by using sodium hyphochloride gel to remove bacteria etc including cost of writing letters "Tank cleaned on (____ Date)" using synthetic enamel paint out side the tank of PVC water tanks 500 litres capacity completed all as directed.
Description all as per Item No 13.00 here-in-before but of capacity 1000 ltr complete.
S & F in repairs rotational moulded polythyne water storage tank, triple layered, dust proof with ISI marked black/white colour (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 ltrs including dismantling the existing one all as directed.
S & F in repairs PVC water tank cover of existing make suitable for 1000 ltrs capacity with fixing PVC hinges, bolts & locking arrangement etc complete all as specified and directed.
M & L for repair to fire hydrant valves of size 63/80/100 mm dia and shifting at civil workshop by transport, opening up the defective valves and taking out spindle and gate from sluice valve and removing the old threads by grinding and making a new threads by brass welding, turning & polishing to the spindle at civil workshop on grinding machine as per original threads and refixing the same at position and testing complete all as specified and directed by Engr-in-Charge.
Taking out old unserviceable DI/CI pipe with all fittings from trenches or above ground level of following sizes all as directed :-
(a) 80 mm bore
(b) 100 mm bore
(c) 150 mm bore
(d) 200 mm bore
(e) 250 mm bore
(f) 300 mm bore
Laying only DI/CI pipe new or old position obtained from item No 18.01 to 18.06 including cleaning of following sizes :-
(a) 80 mm bore
(b) 100 mm bore
(c) 150 mm bore
(d) 200 mm bore
(e) 250 mm bore
(f) 300 mm bore
Supply, laying & testing ductile iron tubing class K-7 with all fittings and laid in trenches all as specified and directed for the following sizes :-
(a) 80 mm bore
(b) 100 mm bore
(c) 150 mm bore
(d) 200 mm bore
(e) 250 mm bore
(f) 300 mm bore
M & L for bends any type (radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc), tee pieces single branch, 'Y' junction, double branch, cross, collars, caps and plugs all ends flanged/sockets or socket and spigot up to 300 mm dia bore complete all as specified and directed by Engr-in-Charge.
M & L in repairs for rubber gasket joints with all jointing materials complete all as specified and directed for the following sizes:-
(a) 80 mm bore
(b) 100 mm bore
(c) 150 mm bore
(d) 200 mm bore
(e) 250 mm bore
(f) 300 mm bore
M & L in repairs for run lead joints with all jointing materials complete all as specified and directed for the following sizes:-
(a) 80 mm bore
(b) 100 mm bore
(c) 150 mm bore
(d) 200 mm bore
(e) 250 mm bore
(f) 300 mm bore
Labour only for breaking reinforced cement concrete chajja or conopy or similar items like cement water storage tank etc not exceeding 12 cm thickness for removing rusted GI pipe of any size and making good etc complete all as specified and directed.
S & F in repairs mild steel nuts & bolts, washer flange etc all as specified and directed.
Supply only in repairs lubricating oil of grade 220 all specified and directed. MAKE : Indian oil corporation Servo system-220 or equivalent in Bharat Petroleum or Hindustan Petroleum
Supply only grease for pump bearings as specified and directed. MAKE : Indian oil corporation Servogem-3 or equivalent in Bharat Petroleum or Hindustan Petroleum
S & F in repairs new battery of 12 volts 65 AH battery all as specified and directed.
S & F in repairs bearing No: 6309 ZZ all as specified and directed. MAKE : SKF/TATA/NBC/FAG
S & F in repairs bearing No: 6314 ZZ all as specified and directed. MAKE : SKF/TATA/NBC/FAG
S & F in repairs gland packing for pump of size 30 HP to 150 HP as per site requirement complete all as specified and directed.
M & L for dismantling old unserviceable sump pump set 0.5 HP any type, Supply, installation, testing and commissioning sump pump set, electric driven of capacity 0.5 HP, Single Phase 230 Volts, 50 Hz, Head 23 m, Suction size - 25 mm and delivery size - 25 mm, self priming, CI impeller and CI body complete with all accessories all as specified and directed by Engr-in-Charge. MAKE - Kirloskar, Model - Kirloskar Jalraaj Ultra or equvivalent make in CG NOTE - Old pump to be deposited to MES store yard.
M & L for dismantling electric motor from the centrifugal pumpset/compressor of any make, 3 phase 415 V, 1.5 HP capacity, transporting to workshop, strip opening the motor, cutting and removing burnt winding and rewinding using super enamelled copper wire of suitable gauge to match with the existing winding including varnishing, insulated paper, sleeves tape etc & drying, replacement of ball bearings & bushes of existing size and make, re-assembling the motor, bring back to commissioning at original position/place, connecting with proper alignment and testing complete through authorised service engineer all as specified and directed by Engr-in-Charge.
Description all as per Item No 33.00 here-in-before but 5 HP capacity.
Description all as per Item No 33.00 here-in-before but 15 HP capacity.
Description all as per Item No 33.00 here-in-before but 30 HP capacity.
Description all as per Item No 33.00 here-in-before but 60 HP capacity.
Description all as per Item No 33.00 here-in-before but 75 HP capacity.
Description all as per Item No 33.00 here-in-before but 156 HP capacity.
M & L for overhauling of centrifugal pump sets / vertical turbine pumps 3 phase 415 volts of 1.5 HP capacity by opening up the pumpset, cleaning inside & out side thoroughly, including replacement of gland packing, rubber insertion, replacement of bearings - 2 Nos (DE/NDE) and testing complete all as specified and directed by Engr-in-Charge.
Description all as per Item No 40.00 here-in-before but 5 HP capacity.
Description all as per Item No 40.00 here-in-before but 15 HP capacity.
Description all as per Item No 40.00 here-in-before but 30 HP capacity.
Description all as per Item No 40.00 here-in-before but 60 HP capacity.
Description all as per Item No 40.00 here-in-before but 75 HP capacity.
Description all as per Item No 40.00 here-in-before but 156 HP capacity.
Dismanting and taking out carefully defective spindle from sluice valve of size 80 mm dia and removing the old gate stud by grinding and making it to a shape by brass welding and turning & polishing, greasing, servicing as per original gate stud and refixing the same at position and testing complete all as specified and directed.
Description all as per Item No 47.00 here-in-before but of size 100 mm dia.
Description all as per Item No 47.00 here-in-before but of size 150 mm dia.
Description all as per item No 47.00 here-in-before but size 200 mm dia.
Description all as per item No 47.00 here-in-before but size 250 mm dia.
Description all as per item No 47.00 here-in-before but size 300 mm dia.
M & L for dismantling old unserviceable 200 mm dia water meter CI body flanged and drilled both ends with strainer, S & F new water meter 200 mm dia CI body flanged and drilled both ends conforming to IS 2373/81 mechanical driven straight reading incl 200 mm dia CI strainer complete all as specified and directed.
S & F in repairs water pressure gauge dial type of range 0-16 Kg/Sqcm all as specified and directed.
S & F in repairs cast iron wafer type butterfly valve of size 300 mm without lugs, gear operated, stainless steel grade 304 disc, Nitrile/ EPDM rubber lining test pressure PN-1.0/PN-1.6 complete all as specified and directed.
S & F in repairs cast iron sluice valve of size 80 mm flanged PN-1.6 ISI conforming to IS :14846 hand wheel operated, stainless steel stem with gun metal parts flanged driller to IS: 1538 non rising stem PN-1.6 all as specified and directed.
Description all as per Item No 56.00 here-in-before but of size 100 mm dia.
Description all as per Item No 56.00 here-in-before but of size 150 mm dia.
Description all as per Item No 56.00 here-in-before but of size 200 mm dia.
Description all as per Item No 56.00 here-in-before but of size 250 mm dia.
Description all as per Item No 56.00 here-in-before but of size 300 mm dia.
S & F in repairs Single Outlet Landing valve (Hydrant Valve) of size 63 mm dia of Straight/Right Angle/Turn Down type made out of gun metal, flanged type, conforming to IS: 5290 along woth cast iron hand wheel operated, female instantaneous outlet, ABS Blank cap and chain complete all as specified and directed by Engr-in-Charge. MAKE: Newage/ Padmini or equivalent make as approved by GE.
S & F in repairs MCCB 400 Amps, 3 pole 50 KA breaking capacity, 415 Volts AC with adjustable thermal magnetic release complete all as specified and directed. MAKE: Indo Asian Cat No. 830401 or equivalent in Havells/Bajaj/Legrand
S & F in repairs MCCB 250 Amps, 3 pole 36 KA breaking capacity, 415 Volts AC with adjustable thermal magnetic release complete all as specified and directed. MAKE: Indo Asian/Havells/Bajaj/Legrand
S & F in repairs HRC fuse links 250 Amps, DIN type, 80 KA, 500 V, AC, 50 Hz, size 1 complete all as specified and as directed. MAKE: GE/Indo Asian/ Siemens/ ABB
S & F in repairs HRC fuse links 125 Amps, DIN type, 80 KA, 500 V, AC, 50 Hz, size 00 complete all as specified and as directed. MAKE: GE/Indo Asian/ Siemens/ ABB
S & F in repairs HRC fuse links 100 Amps, DIN type, 80 KA, 500 V, AC, 50 Hz, size 00 complete all as specified and as directed. MAKE: GE/Indo Asian/ Siemens/ ABB
S & F in repairs HRC fuse links 2 Amps to 16 Amps, 80 KA, 500 V, AC, 50 Hz, FGN complete all as specified and as directed. MAKE: GE/Indo Asian/ Siemens/ ABB
S & F in repairs hand wheel made out of cast iron, suitable for sluice valve of size 80 to 150 mm complete all as specified and directed by Engr-in-Charge.
S & F in repairs hand wheel made out of cast iron, suitable for sluice valve of size 200 to 300 mm complete all as specified and directed by Engr-in-Charge.
Taking out old unserviceable HDPE pipes with all fittings from trenches or above ground level all as specified and directed for the following sizes :-
(a) 75/80 mm bore
(b) 100/110 mm bore
(c) 150 mm bore
Supply, laying, fixing & testing HDPE pipes PN-10 including jointing materials in trenches complete all as specified and directed for the following sizes :-
(a) 75/80 mm bore
(b) 100/110 mm bore
(c) 150 mm bore
S & F in repairs 3-way Inlet Breeching, gun metal body having 3 gun metal, 63 mm male instantaneous inlets, fitted with non-return valves with gun metal drain valves, 3 rubber blank caps and chain complete all as specified and directed by Engr-in-Charge. MAKE: Newage/ Padmini or equivalent make as approved by GE.
S & F in repairs 2-way Inlet Breeching, gun metal body having 2 gun metal, 63 mm male instantaneous inlets, fitted with non-return valves with gun metal drain valves, 2 rubber blank caps and chain complete all as specified and directed by Engr-in-Charge. MAKE: Newage/ Padmini or equivalent make as approved by GE.
S & F in repairs water monitor 2.5" gun metal body, 63 mm male instantaneous inlets, rubber blank caps and chain complete all as specified and directed by Engr-in-Charge. MAKE: Newage/ Padmini or equivalent make as approved by GE.
S & F in repairs rubber seal, blank caps and chain for fire hydrant of any size complete all as specified and directed by Engr-in-Charge.
S & F in repairs hose box made of 18 gauge MS Sheet 800 mm x 600 mm x 250 mm with double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted fire red out side and brilliant white inside yard complete all as specified and directed.
Taking down old unserviceable chemical dosing pump 0.5 HP of any type and supply, installation and testing of new heavy duty Chemical Dosing system plunger type suitable to inject solution upto 25 LPH working pressure 10 kg /cm2 comprising dosing pump coupled with three phase electric motor of capacity 0.5 HP,1440 RPM assembly with agitator in one motor, agitator with SS sweep blade duly FRP coated, FRP tank 150 ltrs capacity, complete unit mounted on heavy duty MS fabricated frame duly anticorrosive paint complete with Chemical grade PVC NRV all as specified and directed. Model No:- SSAPS/CDSPT/25. NOTE: Old pump to be deposited to MES store.
S & F in repairs 3 Phase DOL starter for Dosing Pump suitable for Model SSAPS/CDSPT/25 made of powder coated MS fabricated box consisting of LED indicator, digital Voltmeter, Amp meter, single phase preventor, High voltage low voltage protection complete all as specified and directed. MAKE: L&T, Philips, Bajaj, CG or equivalent as approved by GE.
M/S. NAVEEN ENGINEERING & CO
M/S VERNEKAR AGENCIES
Bidder Name
K.G.SHANKER
M/S VERNEKAR AGENCIES
M/S. NAVEEN ENGINEERING & CO
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .