NIT NO:140/15FC/RMC/2026 RAIPUR DATED:22/06/2026

PROPOSED BUTTERFLY GARDEN (BIRD PARK) AT NARHARAIYA TALAB, RAIPUR (C.G.)

BILL OF QUANTITY

S.No. PARTICULAR UNIT QTY.

1 (BUILDING SOR ITEM NO.-1.1.1/9) Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. 1.1.1) In all types of soil

2 (BUILDING SOR ITEM NO.-1.26/12) Carriage by mechanical transport upto 5 km lead: 1.26.1 Earth

3 Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm. In depth consolidation each deposited layer by ramming and watering with a lead upto 50M. And lift upto 1.5M.

4 (BUILDING SOR. ITEM NO.- 3.1.3/23) Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size). M- 10

5 (BUILDING SOR ITEM NO.- 3.2/23) Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size). Grade of Concrete M-20

6 (BUILDING SOR. ITEM NO.-3.12/24) Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete: Thermo-Mechanically treated bars FE 500

7 (BUILDING SOR ITEM NO.- 2.1.1/16) Providing and fixing formwork including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: 2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

8 (BUILDING SOR ITEM NO.- 9.3.2/80) 9.3 Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. 9.3.2 Electric resistance or induction butt welded tubes Grade-300

9 (BUILDING SOR ITEM NO.- 10.12/91) 10.12 Supply and fixing of polymer precoated galvalume profile sheets (PPGL) of approved size, shape and pitch of corrugation, total coated thickness (TCT) 0.60 mm +/- 5%, epoxy primer on both side of the sheet and colour polyester top coat 18-20 microns and 6-7 microns on bottom. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

10 (BUILDING SOR ITEM NO.- 10.14) 10.14 Providing and fixing 2mm thick semi transparent polycarbonate profile roofing sheet of approved make and colour to make any normal roofing / covering and fixing as per manufacture specification at spacing not more than 1.2 m centre to centre with EPDM gasket and silicon sealant fixed with self drilling stainless steel screws all complete as per direction of Engineer-in-Charge.

11 (BUILDING SOR ITEM NO.- 10.16/91) 10.16 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete :

10.16.6 Gutter. (600 mm over all girth) MTR 96.08

12 9.33 Providing and fixing GI wire gauge of average width of aperture 1.56mm with wire of 0.45mm to existing steel door, window shutter frames with necessary M.S. strip beading etc. complete

13 ( BUILDING SOR. ITEM NO.-14.22.1/134) Painting on new work (two or more coats) to give an even shade with Satin synthetic enamel paint

14 (BUILDING SOR. ITEM NO.-22.1/204) Providing and filling in plinth with sand /crusher dust and hard moorum under floor in layers not exceeding 20 cm in depth and consolidating each deposited layer by ramming and watering, including dressing etc. complete.

15 (BUILDING SOR. ITEM NO.-22.2/204) Suppling and stacking of good earth at site including royalty,loading,unloading and carriage upto 10km(earth measured in stacks will be reduced by 20% for payment)

16 (BUILDING SOR ITEM NO.-22.4/204) Supplying and stacking at site well decayed cow dung manure from approved source, including loading, unloading and carriage upto 5 km (manure measured in stacks will be reduced by 8% for payment).

17 (BUILDING SOR ITEM NO.-22.8/204) 22.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately).

18 (BUILDING SOR ITEM NO.-22.9/204) 22.9 Mixing earth and sludge or manure in proportion specified or directed

19 (BUILDING SOR ITEM NO.-12.49/118) 25 mm thick KOTA stone slab flooring over 20mm (Average) thick base of cement mortar 1:4 laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding rubbing and polishing etc. complete (Area of slab to be over 0.20 SQ.M and upto 0.50 SQ.M)

20 (BUILDING SOR. ITEM NO.-1.18/11) Providing and filling in plinth with sand /crusher dust and hard moorum under floor in layers not exceeding 20 cm in depth and consolidating each deposited layer by ramming and watering, including dressing etc. complete.

21 (BUILDING SOR. ITEM NO.-3.4/23) Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

22 (BUILDING SOR ITEM NO.- 2.1.8/16) 2.1.8 Beams, lintels, Cantilevers & Walls.

23 (BUILDING SOR ITEM NO.- 2.1.5/16) 2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape

24 (BUILDING SOR ITEM NO.- 7.5.4/45) Brick work with modular fly-ash lime bricks (FALG Bricks) confirming to IS:12894-2002 of class designation 40 in foundation and plinth in: 7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand )

25 (BUILDING SOR. ITEM NO.-11.1/103) Providing and making 6 mm thick cement plaster of mix 11.1.2 ) In Cement mortar 1:4 (1 cement : 4 fine sand)

26 (BUILDING SOR ITEM NO.-14.13/133) Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even. As per Inner , outer plastering

27 (BUILDING SOR. ITEM NO.-14.15.1/133) Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: 14.15.1 On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

28 ( BUILDING SOR. ITEM NO.-14.22.2/134) Painting on new work (two or more coats) to give an even shade with Premium synthetic enamel paint

29 (BUILDING SOR. ITEM NO.- 7.6/45) Extra for brick work in superstructure Above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

30 (BUILDING SOR. ITEM NO.-11.3/103) Providing and making 15mm.thick cement plaster on the rough side of single or half brickwall of mix. In Cement Mortar 1:6 (1 cement : 6 fine sand)

31 (BUILDING SOR. ITEM NO.-22.25/207) Providing and Planting following herbs in garden including preparation of soil,base plantation, providing and spreading different fertilizers,soil and sand.

22.25.1 Hedges like Alife,Dorenta,Tikoma etc. EACH 100.00

22.25.2 Furn like arrica,china etc (3year old) EACH 80.00

22.25.3 Hibiscus (Flower) /Rose EACH 80.00

22.25.4 Carpet Grass(Well developed) SQM 833.00

32 (BUILDING SOR. ITEM NO.-12.65/120) Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm

33 (ROAD SOR ITEM NO.-11.2 (a)/43) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 meters and supplying and planting hedge plants at 30 cm apart.)

34 (ROAD SOR ITEM NO.-11.2 (b)/43) Maintenance of Hedge for one year

35 (ROAD SOR ITEM NO.-12.7/45) Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance.

36 (ROAD SOR ITEM NO.-12.8/46) Providing and planting of Bogenbelia dwarf, chandni dwarf, kaner dwarf vr flower bearing plants with 0‟9” x 0‟9” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance

37 (ROAD SOR ITEM NO.-12.10/46) 12.10 Providing and planting of plumeria (Champa) 2‟0” to 3‟0” heighted plants with 1‟0” x 1‟0”x1‟6” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 4 month maintenance

38 (ROAD SOR ITEM NO.-12.13/46) Human and other sculpture -butterfly statue

( b) 2 to 5 feet EACH 2.00

39 (ROAD SOR ITEM NO.-12.14/46) 12.14 Cement art Mural work

40 (ROAD SOR ITEM NO.-4.1/15) Granular Sub-base as per Table :- 400-1 Construction of granular sub base by providing close graded material carriage of mixed material to work site, spreaong in uniform layers with motor grader on prepared surface watering rolling and compacting with vibratory power roller at OMC to achive the disired density complete as per clause401 By mix in place method (b) For Sub-base cum drainage layer or upper sub-base with (i) Grading-V Material.

41 (ROAD SOR. ITEM NO.-8.1/29) 12.5 Manufacturing, supply & fixing of precast kerb stone of size 400mmx259mmx200mm thick made of M-20 concrete rectangular in shape with one corner chamfered by 100 mm x 100 mm as approved design i/c cost of all material, labour and curing etc. complete.

42 (EL.SOR. ITEM NO.-19.12/72) Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as per specification.

6 mtr pole CUM 10.00

43 (EL.SOR. ITEM NO.-19.7.1/71) Supply of hot dipped galvanized (in single dip to minimum 75 micron) octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications with 4 way terminal connector including 3mm thick anchor plate, 4 nos 16mm dia foundation bolts of EN8 grade, and as per IS 2062 & BS EN: 10025. (designed for wind speed upto 180km/hr, IS: 875 Part 3) 4 metre high, dia 130mm at bottom and 75mm at top, base plate size 200x200x12mm, foundation bolts 450mm long

44 (EL.SOR. ITEM NO.-19.9.2/71) Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification. Single Over Hang 0.75 metre Long

45 (EL.SOR. ITEM NO.-19.11.4/72) Erection of GI octogonal/ tubular/conical pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as per specification. 4 metre high

46 (EL.SOR. ITEM NO.-19.24.1/76) Painting of following height steel tubular poles with two coat of approved colour and shade synthetic enamel paint including cleaning the surface as per specification: 21.22.1 upto 6 metre

LT Cable and Termination

47 (EL.SOR. ITEM NO.-15.1.22/52) Supplying and laying following sizes one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

4 x 10 sq. mm. METER 500.00

Panel Incoming Wiring

48 (EL.SOR. ITEM NO.-15.23.23/57) Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as per specification. 4 X 10 sq. mm (22 mm)

49 (EL.SOR. ITEM NO.-32.2.5/142) Providing following size ISI marked FRLS PVC insulated , PVC sheathed, flexible copper conductor wire. 2.5 sq. mm three core

50 (EL.SOR. ITEM NO.-14.1.5/51) Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification. 16.1.5 180 mm outer dia and 152 mm Inner dia

MAIN METAL PANEL BOARD

51 (ELECTRICAL SOR ITEM NO.7.19/34) Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Above 450 mm and upto 600 mm deep

52 (ELECTRICAL SOR ITEM NO.7.20/35) Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 400 amp (50x6mm)

53 (ELECTRICAL SOR ITEM NO.9.1.5/50) 9.1.5 Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu. 3 pole MCCB, 125A, Adjustable Thermal - Magnetic Release, 25KA

Incomer of Lighting Panel EACH 1.00

54 (ELECTRICAL SOR ITEM NO.9.16/44) Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification.

6 amps to 32 amps Each 10.00

55 (ELECTRICAL SOR ITEM NO.10.13/48) Providing and fixing 3 pole, 415/500 volts following rating (AC-1 Duty) power contactor in existing starter/ cubical panel including, connections, testing and commissioning etc. as per specification. 60 amps

56 (ELECTRICAL SOR ITEM NO.10.15/48) Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification. 100/5 amps

57 (ELECTRICAL SOR ITEM NO.10.17/49) Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification.

58 (ELECTRICAL SOR ITEM NO.10.18/49) Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. 0-200 amps

59 (ELECTRICAL SOR ITEM NO.10.20/50) Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. Digital type

60 (ELECTRICAL SOR ITEM NO.10.21/50) Providing and fixing penal mounting selector switch in existing cubical panel including, connections, testing and commissioning etc. as per specification.

For voltmeter Each 4.00

For ammeter Each 4.00

61 (ELECTRICAL SOR ITEM NO.10.22/50) Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as per specification. Analoge type

62 (EL.SOR. ITEM NO.-12.1/48) Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as per specification and IS Code 3043: 1987(R 2016)

63 (EL.SOR. ITEM NO.-12.13/49) Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification.

64 (EL.SOR. ITEM NO.-12.12/49) Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as per specification.

65 (EL.SOR. ITEM NO.-6.28.9/17) Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. 120 watt

PROPOSED BUTTERFLY GARDEN (BIRD PARK) AT NARHARAIYA TALAB, RAIPUR (C.G.)

BILL OF QUANTITY

S.No. PARTICULAR UNIT QTY.

1 NON SOR ITEM supply, fixing & fabricating Butter fly sculptures size around 5'x5' as per design all complete

2 (NON SOR APPROVED RATE FOR RAIPUR SMART CITY) Work of decorative design on MS plate by CNC Cutting using Fiber Laser Cutting

3 (HARYANA PWD SOR. ITEM NO.-26.58.3/375/2021) NON SOR Cast Iron bench of 1800 mm length, 900 mm width, 450 mm seating height, sides made of cast iron. Seat and back shall be made of 10 strips of M.S. pipes 63 mm x 25 mm of 14 gauge with one M.S. Flat 25 x 10 mm welded at the centre, below and back of the seat and back rest. Spray painted with approved brand paint. Fixed by grouting with 1:2:4 cement concrete (Minimum weight of each bench 105 kg). All materials required to be as per BIS specifications.

4 (NON SOR) Making Art and colouring ,Painting in 3D Format etc complete on existing walls of city at any designated places and as per the drawing approved by engineer incharge. )By rubbing ,cleaning & smoothening of rcc wall surface 2. two or more coats exterior weather coat all care putty to give even shade & smoothening surface of approved quality 3. Two or more coats exterior weather coat cement primer to give an even shad & smoothening surface of the approved quality and manufacturing company 4. coloring painting & making art quality & manufacturing campany as per drawing approved and directed by engineer incharge

5 (MP SOR-28.29.1/824/2024 Providing and fixing of White River (stone) pebbles of size 2”to 2.50” dia in natural colour at site of work including loading, unloading, carriage with all taxes paid etc and as per direction of Engineer-in-Charge.

6 (MP SOR-28.29.2/824/2024 Providing and fixing of White Marbles circular/oval in shape (stone) pebbles of size 2”to 2.50” dia in natural colour at site of work including loading, unloading, carriage with all taxes paid etc. and as per direction of Engineer-in-Charge.

7 N.S. Swing Two Seater Height 3 mtr. Width 13.0m Clamp - S.P.Casting clamp with bearing fixing with yhe upper body of pipe with support of 40x5 flat. Seat capacity -2 nos. F.R.P. laminated steel sheet with the support of 30x30x3 angle and 25x5 flat. Main frame - 50x2.5 mm (thickness) @ NB. Pipe Frame hase to be supported with 50x50x5 angle on the both sides and sides to be supported with 20mm pipe with nut bolting system Chain - 8 mm thick M.S. Nikil coated high tensile chain with 's' hook. Ideal for the age group 4-14 yrs. EACH 1.00

8 N.S. Slide Height 1.2m, width of the slide 0.5. Length of slide 2.4 m Mian frame-40mmx 2.5mm (thickness) @ NB. Pipe form if steel frame with support of 25x25x3 angle Ralling of 20x2 mm(thickness) pipe. Frp should b 8' length and 0.5 mtr Stairs made up of square pipe of 100x50mm.& 25x25x3 angl main frame, stairs & frp should properly fixed with support of flat 40x5 with each other withj nut bolting system. Ideal for the age group 4-14 yrs. Painting :- Structure have to be powder coated by best quality polyurethane Paints. Benches should be provide with hole passes for proper grip, fixing with 1:2:4 EACH 1.00

9 N.S. MGR Supplying & fixing of MS marie Go Round as per direction code(RC 506 MGR) EACH 1.00

10 N.S. See Saw Four Seater Height 0.4 m width 1.5 m length 3.0m vertical support - 90 mm <2mm (thickness) NB. Pipe Center pipe - 2 nos. 90 mm x 2mm (thickness). Base - 25 mm x 2mm (thickness) pipe with support of lo mm plate. Handle - 25 mm x 2mm (thickness) pipe on both side. HP. CASTING SYSTEM WITH bush & bearing, seat capacity 4 nos. F.R.P. laminated steel sheet gped with the pipe. ideal for the age group 4- 14 yrs. Painting:- Structure have to be powder coated by best quality polyurethane Paints. Benches should be provide with hole passes tor proper grip. fixing with 1:2:4 cement concrete EACH 1.00

11 N.S. Rainbow climber area 0.6x4.14x1.90 main frame 32mmx3mm pipe prpoerly rounded in 180 degree. Painting powder coated bt best quality polyurethane paints EACH 1.00

12 N.S. Cycle (size110x51x130 ) red dark green or yellow colour. EACH 1.00

13 N.S. Hip twiaster and stepper (size-100x85x150) EACH 1.00

14 N.S. Back shaper (size 122x80x82) EACH 1.00

15 N.S. waist shaper (size 118x75x132.5) EACH 1.00