ADDN/ ALTN TO BLDG NO P-592 SINGLE L/IN ACCN FOR AGV WOMEN AT AF STN ADAMPUR

Amount

BR WORKS

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in SOFT/LOOSE soil complete, all as specified.

Excavation in trenches in soft/loose soil not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth; for foundation, etc. and getting out complete, all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each, complete, all as specified and directed.

Removing excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified and directed.

Broken bricks hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete, all as specified.

M&L for PCC type E-2 (1:5:10), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and directed

M&L for PCC type D-2 (1:4:8), using 40 mm graded crushed stone aggregates as in filling & mass concrete, complete all as specified and directed

M&L for Cement concrete (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in roof kerbs or mud stops, coping etc complete all as specified and directed.

M&L for Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed.

M&L for Reinforced cement concrete, M-25 (Design Mix), as in in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete, M-25 (Design Mix), as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforced cement concrete, M-25 (Design Mix), as in beams, cantilevers, bressumers, lintels over 1.5 metre clear span and the like complete all as specified and directed.

M&L for Reinforced cement concrete, M-25 (Design Mix), as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surfaces of concrete, complete all as specified and directed.

M&L for Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished surfaces of concrete, complete all as specified.

M&L for Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished surfaces of concrete, complete all as specified and directed.

M&L for Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surfaces of concrete, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified.

Cutting grooves in brick wall 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.

Cutting openings, through brick walls, built in cement mortar for door, window & other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective bk wk for under-pinning, including providing, fixing & removing shoring, cleaning & stacking bricks, removing surplus serviceable bricks, hardcore, etc., to store & rubbish not exc. 50 m, complete all as specified.

M&L for Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L for Brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for Brick work in half brick thick wall using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed.

S&F, Factory made, 30 mm thick, second class hard wood, plain framed, hammer marked, skelton shutter (two panel to receive wire gauge) with lock rail . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S&F, Factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,ISI marked, complete all as specified and directed.

S&F, Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

S&F, Factory made solid PVC moulded door shutter, 28-30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2 mm thick plain colur PVC sheet on back face, as shown on page 181 of MES Schedule Part-II, complete all as specified.

S&F, Aluminium anodised barrel tower bolt of extruded section 200 mm long, ISI marked, complete all as specified and directed.

S&F, Aluminium anodised barrel tower bolt of extruded section 150 mm long, ISI marked, complete all as specified and directed.

S&F, Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed.

S&F, Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified and directed. MAKE: PRAYAG CAT HG-3414 or equivalent make mentioned in Appendix 'B'

S&F, Mild steel ordinary rat tail rod pattern helical door spring 250 mm long including roller and roller plate, complete all as specified and directed.

S&F, Extruded aluminium anodised handles 125 mm long fabricated type with plate , ISI marked complete all as specified and directed.

S&F, Double leg aluminium anodised door stopper with rubber foot 100 mm long, ISI marked and fixed to bottom rail of doors with steel screws, complete all as specified and directed.

M&L for welding in repair metal thickness n exc 6mm & n exc. 2.5cm in length, complete all as specified and directed.

S&F, Stainless steel conduit 20 mm bore, cut to size and erected in position as curtain rod on backets, with & including SS decorative finials & brackets, fixed to walls with PVC rawl plugs & SS screws, IN REPAIRS, complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples, complete all as specified and directed

S&F, Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Mild steel TMT bars 5 mm and over up to and including 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for stirrups spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders complete all as specified.

M&L for Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates quality confirming to grade Fe-290-Gde E-165, complete all as specified.

M&L for Mild steel work as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) quality confirming to grade Fe-290-Gde E-165, complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete all as specified and directed.

S&F, Factory made steel windows with side hung shutter with glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

Factory made steel windows with side hung shutter without glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete.

S&F, Steel windows or ventilators, fixed type made of MS sheet 1.25 mm thick box type (primer coated), ERW hollow 'P' section of size 60mm x 25 mm complete all as specified and directed. NOTES APPLICABLE TO SERIAL ITEM NO. 45 TO 47: (a) Profile section used under these items shall be 'P' tube as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable.

Water Proofing Treatment to RCC roofs comprising of : -

Taking down existing water proofing treatment (any no. of layers) from RCC roofs including cleaning the surface including flashings and junction of parapet etc. with wire brushing & water to the entire satisfaction of EIC, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded stone crushed aggregate, laid to slope as directed by Engineer in Charge over RCC roofs as padding, complete all as specified and directed.

M&L for Rendering 15 mm thick (Average thickness) rendering on roof surface including flashings and junction of parapets etc., finished even and fair in cement mortar (1:4), using water proofing compound as recommended by manufacturers after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified and directed. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

M&L for APP based polymeric membrane laid on primed roofs & flashing by forced application using Butane torch and sealing all joints on primed surface by applying hot blown industrial grade bitumen @ 85/25 @ 1.20 kg/Sq.m over a coat of bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces & flashings complete all as specified and directed.

M&L for 40 mm thick brick tiles (EXCEPT TILES) bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed.

M&L for 40 mm thick brick tiles bedded over 15 mm thick cement mortar (1:4), and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed.

M&L for Making benching with PCC (1:2:4) type B-0 (using water proofing compound) along side walls adjoining to roofs, in CONCAVE SHAPE, complete all as specified and directed.

Supply only water proofing compound (WPC), ISI marked, complete all as specified.

M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for 100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified.

M&L for 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded crushed stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'A' complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 18-22 mm thick, in flooring and for staircase step in single piece, laid over over & including 20 mm thick (average thickness) cement mortar (1:3) screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Granite finish) complete all as specified and directed.

M&L for Machine cut Kota stone slab 18-22mm thick on vertical surfaces as in staircase riser skirting/ dado etc in single piece over and including 10 mm thick rendering in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed

M&L for Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed.

M&L for Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified and directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., and brushing a coat of cement slurry with 3 kg of cement per Sq.m, complete all as specified and directed.

M&L for 80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 25mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete.

M&L for Glazed ceramic coloured tiles 7mm thick, area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.06 Sq.m but n. exc. 0.11 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, on vertical surfaces as in skirting etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Repairing of RCC projection chhajjas, roof, facia etc by necessary preparation. Scraping cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC with cement concrete Type A-0 (1:1.5:3) and reinforcement with chicken mesh of weight not more than n.exc 3 kg/Sq.m (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches of area n.exc 5 Sq.m and thickness of RCC member n.exc 70 mm incl necessary formwork at any height/location complete all as specified and directed. NOTE: The rate quoted by the contractor shall included for chicken mesh, scaffolding and necessary formwork upto triple storey bldg.

M&L for Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified and directed. NOTE: WPC will be measured and paid for separately under respective item of BoQ.

M&L for two coat of interior acrylic distemper/oil bound distemper on old decorated ceiling surfaces, including complete removal of existing treatment of any description, complete all as specified and directed.

M&L for Three coats of white washing on new undecorated ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) Two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer.

S&F, Sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified and directed.

S&F, Figured glass 4mm thick ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sq.m in each pane complete all as specified and directed.

M&L for One coat (finishing coat) of synthetic enamel paint over wood and wood based surfaces of any description not other wise described over 10cm width or girth, including preparation of surfaces, complete all as specified.

M&L for Two coats of synthetic enamel paint over & including a coat of pink primer over wood and wood based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for One coat (finishing coat) of synthetic enamel paint over old painted steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

S&F, 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

S&F, 1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, complete all as specified including the following acessories: - (i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, complete all as specified and directed. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, complete all as specified.

Disconnecting existing tanks of capacity exceeding 500 litre but not exceeding 1000 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing on existing location after necessary cleaning by removing all scale and dirt etc. including cleaning mouth of circulating service pipes also making all necessary connection complete, all as specified.

S&F, Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified of size: -

15mm bore

20mm bore

S&F, Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix 'B'.

S&F, Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix 'B'.

S&F, Concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. MAKE: PRAYAG Cat No. 6518 or equivalent make mentioned in Appndix 'B'.

S&F, Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. MAKE: PRAYAG Cat No. 6508 or equivalent make mentioned in Appendix 'B'.

S&F, Centre hole basin mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB111027 or equivalent make mentioned in Appendix 'B'.'.

S&F, Wall mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. MAKE: KEROVIT Cat No. KB511021 or equivalent make mentioned in Appendix 'B'.'.

S&F, Overhead ABS shower with cast copper alloy chromium plated arm 125 mm long with flange and fixed in position, complete. MAKE: PRAYAG Cat BS-76 or equivalent make mentioned in Appendix 'B'.

S&F, Vitreous China wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with 1.50 metre long braded tube tube, soft close PVC seat & cover and uPVC 'S trap, IN REPAIRS, complete all as specified and directed MAKE OF EWC: PRAYAG Cat No. 4016 or equivalent make mentioned in Appendix 'B'.

S&F, Vitreous China wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with 1.50 metre long braded tube tube, soft close PVC seat & cover and uPVC 'S trap complete all as specified and directed MAKE OF EWC: PRAYAG Cat No. 4016 or equivalent make mentioned in Appendix 'B'.

S&F, Vitreous China wash hand basin, counter type, white, oval shape of size 560 x 410 x 180 mm including fixing acessories like 32mm dia CP waste coupling, CP bottle trap & PVC collapsible waste pipe complete. MAKE:PRAYAG Cat No. 4790 or equivalent make mentioned in Appndix 'B'.

S&F, PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, complete all as specified and directed. MAKE: PRAYAG Cat No. 502 or equivalent make mentioned in Appendix 'B'

S&F, 5-6 mm thick looking glass fixed over not less than 6 mm thick PVC ply and approved shade PVC beading not less than 15 mm wide alround with and including all fixing acessories, complete all as specified and directed.

S&F, Corner Glass shelf 300 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, complete. MAKE: PRAYAG Cat No. BEA-44 or equivalent make mentioned in Appendix 'B'.

S&F, Brass chromium plated towel rail 500-600 mm long, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BA-10 or equivalent make mentioned in Appndix 'B'.

S&F, Stainless steel soap dish, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BA-05 or equivalent make mentioned in Appendix 'B'.

S&F, Stainless steel round slotted grating with frame, 100 mm size fixed in position with cement joints, complete all as specified and directed.

S&F, PVC connections with PTMT nuts, 450 mm long, complete all as specified and directed.

S&F, Stainless steel peg set of six, fixed to wall with SS screws and PVC rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-30 or equivalent make mentioned in Appendix 'B'.

S&F, uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, complete all as specified and directed.

S&F, uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, complete all as specified and directed.

S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia, complete all as specified and directed.

S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia, , complete all as specified and directed.

S&F, uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 75 mm external dia, complete all as specified and directed.

S&F, uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 110 mm external dia, complete all as specified and directed.

S&F, uPVC floor trap, suitable for uPVC soil waste discharge pipes 110 mm ext dia, embedded in PCC type B-1(1:2:4), complete all as specified and directed,

E/M WORKS

M&L for Point wiring with multi-stranded copper conductor, single core, FRLSH PVC insulated and unsheathed cable, including FRLSH PVC insulated unsheathed stranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, with and including MS terminal boxes with 3 mm thick plastic laminated sheet cover having necessary cutting for fixing switches/ sockets comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. or for bell/buzzer with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit complete all as specified and directed.

One light point controlled by two no., 2 way switches with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit all as specified.

One socket outlet three pin, 6/16 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC medium duty concealed conduit all as specified.

NOTES: (a) Switch(es) & socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. (b) MS boxes shall be fixed flush to walls in position with cement mortar (1:4) complete all as directed. (c) Conduit shall be laid on surface in case of RCC ceiling surfaces.

S&F, Switch piano flush button single pole one way, 6 Amp complete all as specified.

S&F, Switch piano flush button single pole two way, 6 Amp complete all as specified.

S&F, Switch piano, bell/buzzer push, flush button single pole one way, 6 Amp complete all as specified.

S&F, Switch piano flush button single pole one way, 16 Amp complete all as specified.

S&F,Socket outlet multipurpose having provision for 2&3 pin, 6 Amp, flush type, complete all as specified.

S&F, Socket outlet multipurpose having provision for two-in-one 3 pin 6 Amp & 3 pin 16 Amp, flush type complete, all as specified.

S&F, Ceiling rose, surface bakelite, 65 x 50mm, three terminals complete, all as specified.

S&F, Lamp (angle) holder, insulated body, cord grip pattern, complete, all as specified.

S&F,Electric buzzer AC 230 volt, single pole, Ding Dong type complete, all as specified.

S&F, Fan regulator (electronic) suitable for 48”/56” sweep fan, stepped type, single phase, complete all as specified.

S&F, Sub main wiring (with approved colour coding as per IS) with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade (main cable: number of runs as indicated below along with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade for earthing in conduits, complete all as specified for the following: -

2 runs of 6 Sq. mm main cable + 1 run of 6 Sq. mm earth cable.

NOTES: (i) Conduit & conduit accessories shall be measured & paid for separately. (ii) For payment purposes, total runs of main cable (Two run of one running metre) as mentioned above and one run (one running metre) of earth cable shall be considered together as "1 RUNNING METRE"

S&F, Rigid non metallic, PVC concealed conduit, 20 mm bore, medium grade, ISI marked, inclusive of all fitings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing acessories such as couplers, lock nuts, saddles, pipe hook etc. for sub main wiring and the like complete all as specified.

S&F, Sheet metal enclosure for DB for fixing MCB’s, isolators etc., having IP-43 protection, suitable for surface and flush mounting, complete all as specified comprising the following: -

SPN, 12 way with 200 Amp rated bus bar, 240 V, double door type.

VTPN, 4 way with 200 Amp rated bus bar, 415 V, double door type having housing and including MCCB 4 pole 63 Amp, 16kA.

S&F, MCB suitable for 240 volt AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 6 to 32 Amp complete all as specified and directed.

S&F,MCB suitable for 240 volt AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 kA, 'C' curve type of rating 32 Amp complete all as specified and directed.

S&F, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 volt, breaking capacity not less than 10 kA, complete all as specified and directed.

S&F, Environment friendly, modern design, energy saving surface mounted, decorative 10 W bulk head LED luminaire with premium quality diffuser for glarefree light, pressure die cast aluminium housing 6000K, including making connections, complete all as specified and directed.

S&F, Surface mounted environment friendly LED batten with powder coated aluminium housing with intigrated electronic driver with THD<10% LED 10W lighting fixture 2 feet long, 6500K, lumen output should not be less than 90 lumens per watt, including making connections, complete all as specified and directed.

S&F, Surface mounted environment friendly with eye soft technology & glarefree diffuser decorative box type LED 20 W lighting , 6500K, lumen output should not be less than 90 lumens per watt complete all as specified and directed.

S&F, LED street light 35 watt 230 V AC, outdoor type pressure die cast aluminium housing, heat resistant toughtened glass with frame and lamp with minimum efficiency 110 LM/W, IP 66 protection, CCT 5700K IN REPLACEMENT and making connections including GI bracket suitable dia and size, complete all as specified and directed.

S&F, LED flood light 70 watt, outdoor type pressure die cast aluminium housing, heat resistant toughtened glass with frame and lamp with system efficiency > 110/120 LPW, 10KV SPD IP 66 protection IN REPLACEMENT and making connections, complete.

M&L for Clean dry sand ( locally available) as cushioning for under ground cable 230 mm thick (one layer of 80 mm thickness before laying the cable and other layer of 150 mm thickness after laying the cable) complete all as specified and directed. NOTE:- Punned down thickness (over all 180 mm) shall be considered for measurement and payment.

Brick protection with pulverized fuel ash lime bricks laid flat across the route of underground cable all as specified.

M&L for Boring holes under road pavement / hardstanding by trenchless technology using ultrasound technique and necessary machine for inserting & including 75-100mm bore HDPE pipe complete all as specified and directed.

GI pipe light grade with all fittings fixed as termination postal ,fixed to poles/ walls/ under floors/ under road etc complete all as specified of following size: -

40 mm bore

Supplying, laying, jointing and testing XLPE insulated heavy duty multi stranded armoured and PVC sheathed LT cable 1100 volts grade with aluminium conductor laid in trenches/ ducts/ along poles/ through pipes, of following description: -

25 Sq.mm, 4 core

NOTE:- Excavation and earth work, brick protection and sand cushning will be measured & paid separatly under respective item of BoQ)

M&L for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia (upto DB's earth point) by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh, factory made PCC earthing pit chamber & cover including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of MES Schedule Part – I. NOTE:- (i) Factory made PCC pit chamber shall be provided at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) The unit rate includes earthing lead & protection pipe upto 7.5 metre from top of earth plate. (iii) Earth testing will be done by contractor and earth resistance shall be less than 10 ohm. In case the test results are not found less than 10 ohm, complete earthing shall be redone by the contractor without any extra cost to Govt.

S&F, Electric water heater, storage type steel body with steel inner tank and heating element upto 2 KW capacity 25 ltrs, BEE 5 star rated complete all accessories such as safety valve, thermostate,NRV, connection piece, hot and cold water connection pipe suitable for hot water complete all as specified and directed .

S&F, Exhaust fan 250 mm sweep with blades, frame and louvers, AC single phase, 230 V, PVC body, heavy duty, fixed to wall with 10 mm dia fasteners, nuts & bolts and connecting up from ceiling rose or connector to fan, complete all as specified and directed. .

S&F, Exhaust fan 300 mm sweep with blades, frame and louvers, AC single phase, 230 V, steel body, heavy duty, fixed to wall with 10 mm dia fasteners, nuts & bolts and connecting up from ceiling rose or connector to fan, complete all as specified and directed. .

S&F BLDC Ceiling Fan complete with blades, down rods and accessories 230 V, 1200mm sweep, min air delivery 210 CFM with service valve 6.00 BEE Five star rated with brushless direct current motor IN REPAIRS complete all as specified and directed.

Disconnecting & taking up electric water heater of any capacity or description and refixing & reconnecting the same on same or new location with & including provision of 04 nos. 10 mm dia fasterners, complete all as specified and directed.

Disconnecting & taking up exhaust fan of any type and any capacity or description, depositing in MES Store and refixing & reconnecting the same on same or new location with & including provision of fasterners, complete all as specified and directed.

DISMANTLING/DEMOLITION WORKS

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Demolition of mud phuska in roofs, of thickness not more than 200 mm including plaster and leeping plaster complete all as specified and directed.

Dismantlig brick tiles in roof laid dry and pointed in cement mortar complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, complete all as specified and directed.

Demolition of stone slabs, kotastone/ granite slab of any description or thickness , complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete with batten, casing caping of MS or and PVC conduit on surface or concealed, including switches, ceiling roses, pendants, regulators, sockets, mild steel terminal boxes etc., removing materials and making good disturbed surfaces due to taking down etc. to the entire satisfaction of Engineer-In-Charge, complete all as specified.

Taking down carefully by unscrewing from boards/ outlet boxes, fitting and fixtures such as switches ceiling roses, pendants, regulators, sockets, mild steel terminal boxes bulkhead fittings light fittings, tube light fittings and regulators etc for reuse at site or carrying to the store complete all as specified and directed. (To be measured only when found serviceable in all respect complete for reuse) , complete all as specified.

Taking down carefully copper/aluminium sub main wiring complete, including existing batten/conduit consealed/surface etc., removing materials and making good disturbed surfaces due to taking down etc. to the entire satisfaction of Engineer-In-Charge, complete all as specified and directed.

Dismantling of unservisible existing DBs of any description with all accessories and MCBs, isolators etc. and making good surface as per existing, complete all as specified and directed.

Taking down carefully light fitting of any description, complete all as specified and directed.

Taking down carefully electric bell/buzzer of any description, complete all as specified and directed.

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

KAMAL AGGARWAL (BID ID -3481332)

N S ENGINEERS (BID ID -3481011)

BHARAT ENTERPRISES (BID ID -3481339)

PRATHAM TRADERS (BID ID -3481249)

M/s Sahib and Company (BID ID -3479628)

AAR KAY BEE ENTERPRISES (BID ID -3481213)

R K ENTERPRISES (BID ID -3486353)