Balance work of C/O Store I/C Junior Engineer Residence on Bharmour to Hadsar road at Gala Katai in Tehsil Bharmour (SH Wire Gauge shutter, interlocking paver, boundary wall with Railing and painting works.

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and retuning the stacked soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetra consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings balconies and access platform including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone aggregate 20mm (twenty millimetre) nominal size) at plinth level in Cement Mortar 1:6 (one cement isto six sand) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying in Reinforced cement concrete work with 1:1.5:3 (One cement is to one decimal five coarse sand is to three graded stone aggregate20 mm ( twenty millimetre )nominal size).excluding the cost ofcentering, shuttering, finishing and reinforcement - All work up to plinth level in beams, suspendedfloors, roofs having slope up to 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level up tofloor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate20 mm nominal size)

Providing Tor steel reinforcement Thermo Mechanically Treated bars of grade Fe-500D of Tata Tiscon/Sail for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and layingg cement concrete 1:3:6 ( one cement is to three sand is to six graded stone aggregate 40mm ( forty millimetre nominal size ) and curing completed excluding cost of form work in boundary wall of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 35mm thick ( thirty five millimetre ) shutters Second class teak wood wire gauge shutters usinggalvanized M.S. wire gaue of average width of aperture 1.4mm ( One decimal four millimetre ) in both direction with wire of dia 0.63mm ( zero decimal sixty three millimetre ) , fordoors, windows and clerestory windowos with hinges and necessary screws of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying 6mm (Six millimetres) thick cement plaster in cement mortar 1:3 (One cement : Three sand) upto all floor levels complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth witth cement mortar 1:6 (One cement isto Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 40mm Forty millimetre) precast interlocking block heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concretewith 25mm thick average thickness of cement mortar 1:4 (1 cement : 4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curin rubbing & polishing complete (Subbase concrete floor to be paid for separtly within all leads, lifts and other incidentals The rate including octroi, royality, Malkana, toll tax, gst or other taxes imposed by the Government.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm ( eighteen millimetre ) thick stone slab over 20mm ( average ) thick base of cement mortar 1:4 ( One cement is to ffour coarse sandd ) laaid andd jointed with cement slurry and pointing with white cement slurry sdmixed with pigment of matching shade including rubbing, curing and polishing etc.including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 1.66mm ( One point sixty six millimetre ) to 2.0mm (Two point zero millimetres) thick eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid separately) including fixing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing corrugated 0.63 mm thick with zinc coating not less than275 gm/ m² G.S. sheet roofing includingvertical / curved surface fixed with polymer coated J or Lhooks, bolts and nuts 8 mm diameter with bitumen andG.I. limpet washers or with G.I. limpet washers filled withwhite lead, including a coat of approved steel primer andtwo coats of approved paint on overlapping of sheetscomplete (up to any pitch in horizontal/ vertical or curvedsurfaces), excluding the cost of purlins, rafters andtrusses and including cutting to size and shape whereverrequired. within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing ridges or hips of width 60 cm ( sixty cenitmetre ) overall widthplain G.S. sheet fixed with polymer coated J or L hooks,bolts and nuts 8 mm dia G.I. limpet and bitumenwashers complete.0.63 mm thick with zinc coating not less than275 gm/m²within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flushing 38cm ( thirty eight centimetre ) overaall with 0.60mm ( zero decimal sixty millimetre ) thick pre painted sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating+ back coat of polyester of 5 microns over 5 microns primer coating including fixing with prepainted J or L hooks, bolts and nuts 6mm ( six millimetre ) dia metre & prepainted G.I. limpet & bitumen washers complete with all accessories as required as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting wood work (including priming coat) with enamel paint of Asian paint / Dulux paint /Berger paint/ Nerolac paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture including cleaning the surfaces of all dirt, dust and other foreign matter complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying plaster of paris putty of 2mm ( two millimetre ) thickness over plastered surface to prepare the surface even and smooth complete as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Finishing walls with 100% Premium acrylic emulsion paint having voc less than 50gm/litre and UV resistance as per IS 15489:2004 , Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot Tinted) with silicon additives.New work ( Two or more coats applied @ 1.43 litre/10 sqm . over and including priming coat of exterior primer applied @ 0.90 litre /10 sqm complete as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering with dry distemper of approved brand andmanufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Painting Steel work (including priming coat) with Deluxe Multi Surface paint to give an even shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10 sqm (Zero point eighty litre per ten square metre) of approved brand and manufacture including cleaning the surfaces of all dirt, dust and other foreign matter complete as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying csemi circular pipe with earth work and PCC 1:2:4 ( One cement is to two sand is to four aggregate ) 20mm ( Twenty millimetre) as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Making connection of 25 mm to 40mm ( twenty five millimetre to forty millimetre ) G.I. distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing high pressure 110 mm dia. ( one hundred ten dia) (pressure shall not be less than 4kg/cm2) PVC Spigot and Socket, waste and ventilating pipe of approved make (Finolex, Vectus) ISI Marked including fixing with approved adhesive complete.as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing high pressure 75 mm( seventy five millimetre ) dia. PVC Spigot and Socket, waste and ventilating pipe of approved make (Finolex, Vectus) ISI Marked including fixing with approved adhesive complete.as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110 mm( one hundred ten millimetre ) dia. PVC door bend with oval acess door, insertion rubber washer 3mm ( three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive complete. as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 110 mm X 75 mm.( one hundred ten in to seventy five millimetre ) PVC floor trap with SS grating ISI Marked of self cleaning design including fixing with approved adhesive, cost of cutting amd making good the walls and floor etc. complete and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 110 mm dia. PVC Collar ISI Marked including fixing with approved adhesive complete. including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150 mm ( one hundred fifty millimetre ) dia PVC clamp PVC Clamps ISI Marked of approved design with steel screw and rawal plug etc.complete . including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm ( one hundred ten millimetre ) dia PVC collar ISI Marked including fixing with approved adhesive fitting and design complete complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm ( one hundred fifty millimetre ) dia PVC clamps ISI Marked with steel screw and rawal plug etc complete including fixing with approved adhesive fitting and design complete complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm ( Seventy five millimetre ) dia PVC Cowl ISI marked of approved including fixing with approved adhesive fitting and design complete complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm ( One hundred ten millimetre ) dia PVC Cowl ISI marked of approved including fixing with approved adhesive fitting and design complete complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china pedestal type/wash down floor mounted water closet (WC) with size (570x350x390)mm white colour studio set along with 8mm dia C.P/ S.S JET,SEAT COVER, Flushing CISTERN (10ltr. cap.) and twin flushing valves etc. complete in all respect, water closet (European Type - WC pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 ( one cement, one sand) (with cistern, seat cover and flush fitting) Star White of approved make (Parryware, Hindware, Neyeer, Cera) approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing IS marked big size No. 2071 Cera in white colour vitreous china water closet squatting pan (Orrisa type W.C. pan) size 58x44cm (fifty eight into forty four centimetres) orissa pattern (earth work, bed concrete, foot rest and trap to be measured and paid for separately) STAR S HINDWARE 390x350x570mm (Three hundred Ninety into Three hundred fifty into Five Hundred Seventy milimetres) as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Health faucet ABS with rubbit cleaning system, flexible tube upto 1.25 mtr. long PVC Flexible tube & ABS wall hook to extended wall mounted type W.C. of quality and make (Kingston, Gem, Parko, JAL, ESS, Jaquar, Seiko) as approved by Engineer-In-Charge. within all leads, lifts of materials and other incidentals including entire carriage of materials The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing (550x400)mm wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap of approved make (Parryware, Hindware, Neyeer, Cera) carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board (510x1040)mm bowl depth 250mm. of approved make (AMC, UNIK, DIAMOND, Neelkanth) within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm( fifteen millimetre) nominal bore, C.P. brass bib cock of approved quality conforming to IS:8931 : including carriage of material upto all leads and lifts and as per direction of Engineer In Charge. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm ( fifteen millimetre) nominal bore, C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms including carriage of material upto all leads and lifts and as per direction of Engineer In Charge.within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm ( fifteen millimetre) nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 including carriage of material upto all leads and lifts and as per direction of Engineer In Charge. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15 mm (Fifteen millimetre) nominal bore with 30cm (thirty centimetre) length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour of Finolex/Relpipe(Reliance)/Vectuscomplete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32 mm( thirty two millimetre) dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.including carriage of material upto all leads and lifts and as per direction of Engineer In Charge.. including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C. P. Brass overhead shower rose with 15mm or 20 mm inlet: 85mm with single flow and shower arm including carriage of material up to all leads and lifts and as per direction of Engineer In Charge. within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 25mm ( twenty five millimetre) nominal size gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of material to all leads and lifts and as per direction of Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm( fifteen millimetre) nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, including carriage of material to all leads and lifts and as per direction of Engineer-In-Charge. and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm ( fifteen millimetre nominal bore) to wall, ceiling and floor galvanised mild steel tubes (heavy grade) tube fitting and clamps including making good the wall, ceiling and floor:- including carriage of material up to all leads and lifts and as per direction of Engineer-In-Charge. other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x450 mm ( six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm( Six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.r incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x120x5mm ( six hundred into one hundred twenty into five millimetre) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing CP brass soap Dish Holder having length of 138mm, ( one hundred thirty eight millimetre ) breadth 102mm,( one hundred two millimetre ) height of 75mm( seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms. including carriage of material to all leads and lifts and as per direction of Engineer In Charge. including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design . The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P. brass paper Holder including carriage of material up to all leads and lifts and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing uplasticised PVC connection pipe with brass unions 45cm ( forty five centimetre) length 15 mm ( fifteen millimetre ) nominal bore including carriage of material in all leads and lifts and as per direction of Engineer In Charge. including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm ( fifteen millimetre ) dia bore brass full way valve with wheel including carriage of material in all leads and lifts as per direction of Engineer-In-Charge. and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110 mm( one hundred ten millimetre ) dia PVC Tee including carriage of material in all leads and lifts and as per direction of Engineer In Charge. as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75 mm dia.( seventy five millimetre ) dia PVC Tee including carriage of material in all leads and lifts and as per direction of Engineer In Charge. as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing CP brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm ( six hundred millimetre) long towel rail with total length of 645 mm, ( six hundred forty five millimetre ) width 78 mm( seventy eight millimetre ) and effective height of 88 mm, weighing not less than 190 gms. and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing CP brass towel ring trapezoidal shape 215 mm( two hundred fifteen) long, 200 mm( two hundred millimetre) wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. with carriage of material up to all leads and lifts and as per direction of Engineer-In-Charge. as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing GYSER 25 LITRE CAPACITY 2000 watts as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing GYSER 5 LITRE CAPACITY 2000 watts watts as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

KARNAIL SINGH GOVT CONTRACTOR (BID ID -510783)