SPECIAL REPAIR TO BLDG NO P-1 OFFRS MESS CMDC (SWC) UNDER AGE B/R IV OF GE(S) JAIPUR

Amount

Taking down cement plaster or cement lime plaster/ tiles of any descrption on PCC/ stone surface/ brick surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc

M & L Rendering 15 mm thick on stone masonry wall surfaces in CM 1:6 finished even and smooth without using extra cement

M & L rendering 15mm thick on stone masonary surfaces or surface other than fair faces of brick work on wall in CM 1:4 finished even and smooth without using extra cement.

M & L Rendering 10 mm thick on ceiling in CM 1:4 finished even and smooth without using extra cement

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distermper over a wall care putty

M & L preparing new plastered surfaces and applying two coats of oil bound distemper on ceiling over wall care putty

M & L preparing new plastered surfaces and applying two coats of cement base paint on wall

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises

M&L 25mm thick plain cement concrete type B-0, 1:2:4 ( 12.5mm graded stone aggregate) as in floor

S&F coloured glazed ceramic tiles size 300 x 450mm x7mm thick edge cut/ joint free on walls etc in the combinatin of light and dark shade concept set & jointed in neat cement slurry & pointed in white/ coloured cement to match over 15mm thick plaster in cement mortar (1:4)

Non skid cermic coloured tiles 7 to 8mm thick joint free (square/ rect) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match & including 15mm thick screed bed in CM 1:6

S&F light shade vetrified ceramic tiles edge cut 10mm thick ( square/ rectangular ) polished, area of each tiles not exceeding 0.36sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:4) finished fair and even

All as per item No 12 ditto above but as in skirting/ vertical surface over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4

M&L chequered cement concrete tiles 20cm x 20cm x 20mm thick , set , jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in CM 1:6

M & L for 25 mm thick sand cushion layer complete all as specified and directed

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement all as specified and directed

S&F in repair for two way bib cock with wall flange and aerator complete all as specified and directed by Engr-in-Charge. Make Jaguar Cat part No. - KUP- 35041PM and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair PVC connection 15mm dia 60cm long with 2 Nos brass check nuts with washer complete all as specified

S & F in repair CP fancy type centre hole basin mixer 15mm bore cast copper alloy with 450mm copper hose/ braided hose without popup waste system quarter turn complete all as directed. Make Jaguar Cat part No. - KUP- 35011BPM and equivalent cat part in other makes as per Appendix 'B'.

S & F in repair stainless steel towel rail 450mm long of fixed with and including chromium plated brass screws and wooden / plastic cleats ( minimum weight 170 gms). Make Jaguar Cat part No. - ACN- 1111BNM and equivalent cat part in other makes as per Appendix 'B'.

S & F as in repair stop valves Regular Body of Concealed Stop Cock Suitable for 15 mm Pipe Line with Protection Cap (without Exposed Parts) and Exposed Part Kit of Concealed Stop Cock & Flush Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange with Seal, screwed both ends for iron pipe or for unions in 15 mm bore fixed .. Make Jaguar Cat part No. - ALD-083 and KUP- 35083KPM and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair 15mm bore chromium plated bib taps (fancy type) long body cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes all as specified. Make - jaguar, cat part no. KUP-35037PM and equivalent cat part in other makes as per Appendix 'B'.

Demolition of old existing unserviceable WHB glazed incl demolition of granite and S&F table top vitreous china wash hand basin white of size 485x370x150 mm flat back complete including all connected accessories and cutting for and pinning in granite/wall for fixing WHB with all finishes complete in repair. Make Jaguar Cat part No. - SLS-WHT-6901 and equivalent cat part in other makes as per Appendix 'B'. (Note : New granite fixing measured separately)

Demolition of old existing unsv EWC seat and S&F Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-300mm complete . Make Jaguar Cat part No. - LYS-WHT-38851S300UFSMN and equivalent cat part in other makes as per Appendix 'B'.

S&F in repairs vitrous china squatting pan of size 580 x 440 mm (Orrisa pattern), white with integral foot rest (excluding flushing cistern & flush pipe) including antisyphonage pipe complete all as specified.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .

S&F in repairs stop valve 15mm copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions . Make Jaguar Cat part No. -KUP-35053PM and equivalent cat part in other makes as per Appendix 'B'.

S&F in repairs stop valves 20mm bore copper alloy screwed down high pressure with crutch of butter fly handle screwed both ends for iron pipe or for union

S & F in repair Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook complete . Make Jaguar Cat part No. -ALD-573 and equivalent cat part in other makes as per Appendix 'B'.

Dismantling of old unserviceable trap and S&F of PVC Nahani / floor trap and square in size of 100 x 100mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap/ Nahani trap

Dismantling and taking up or down the existing unserviceable GI pipe and S&F galvanised steel water tubing medium grade with all fittings and fixed complete to walls and celing or laid in floors of following :-

(a) 15 mm bore

(b) 20 mm bore

S & F 500 Ltrs capacity rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe pipe etc complete all as specified in SSR Part I, Make - Sintex or eqivalent including dismantling old water tanks

All as per item No 33 above but 1000 ltrs capacity

S & F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed bore dia of pipe 20mm

M&L for providing circular, raised platform of height 20cm below the tank and base 15cm more than the external dia of tank of PVC cylindircal water tank of capacity 500 / 1000 litre using PCC 1:3:6 type C-1 using 20mm graded stone aggregate with smooth finish complete all as directed.

S&F in repair box type mirror PVC cabinet of size 475 x 600 x 150mm all as specified

S&F in repair Paper Holder with Flap Recessed Type(Stainless Steel) fixed with (CP) brass screws fixed in repair . Make Jaguar Cat part No. -AHS-1553 and equivalent cat part in other makes as per Appendix 'B'.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with the help of PVC clamps fixed to walls for rain water pipe type 'B' ISI marked of 75mm bore in repair

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 75mm bore in repair.

S&F UPVC (SWR) pipe single socketed, any in length with rubber ring joints laid in trenches or in floors type 'B' ISI marked of 110mm bore in repair

S&F UPVC (SWR) bends of any radius 75mm bore in repair

S&F UPVC (SWR) bends of any radius 110mm bore in repair

S&F UPVC (SWR) vent cowl 110mm in repair

S&F PVC (SWR) floor trap 75mm dia plain with grating including joining with solvent cement in repair

M&L PVC (SWR) gully trap 125/110mm setting & jointing with solvent cement in repair

S&F in repair Corner glass shelf (large) complete all as specified and directed by Engr-in-Charge. . Make Jaguar Cat part No. -ACN-1173) or equivalent cat part in other makes as per Appendix 'B'.

M&L in repair fancy type SS brackets for curtain rod fixed complete all as directed.

M&L of 20mm dia drapery fancy type curtain rod fixed in repair

M&L for fancy type caps/ side bulbs PVC powder coated suitable for curtain rod fixed in repair

Taking down chowkats or frames with shutters exc 1.50 sqm but n exc 4.00 sqm each (without taking off shutters from the frames).

Taking down chowkats or frames with shutters not exc 1.50 sqm each (without taking off shutters from the frames).

Taking down shutters of any description exc 1 sq.m and not exc 2.00 sq.m each

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (stiles) with 2, 4 or raised panel design with2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying & fixing in frame at site as per specification & drawing including PVC sheet fixed on flush shutter in lipping in case of PVC sheet is heat bent as lipping on the edges of doors

S&F solid PVC frame ( single rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth out integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and shown on drawing (Note := Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

M & L pressed steel door frame of size 125mm x 60mm with one or more rebates including necessary fixing lugs , lock strike plate and including provision of fixed 100mm hinges etc complete as specified.

M & L pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs , lock strike plate and including provision of fixed 100mm hinges etc complete as specified.

M&L for PCC 1:3:6 type C1 as in filling back side of pressed steel door frames

M & L Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M & L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) tomatch the existing floors complete.

Cutting holes in stone/ brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of hold fast n. exc half brick

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I complete all as directed.

S & F butt hinges of size 100mm medium weight cold rolled mild steel and fixed

S&F aluminium anodised barrel tower bolts 150mm long of extruded section

S&F aluminium alloy anodised sliding door bolts 300mm long with hasp and staple ( bolt type) & fixing clips of sheet or extruded section & fixing bolts & sliding bolts of extruded section

S&F aluminium anodised handle 125mm size

S & F aluminium anodised floor door stopper overall length 140mm double legged with rubber shoe fixed to bottom rails of door

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F in repairs Aluminium body ( extruded section ) body Door closer hydraulically regulated, designation No. 3 , universal type , suitable for door shutters 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

S&F galvanised mild steel wire cloth 0.50mm nominal dia of wire and average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples all as specified

M & L Preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer

M&L Machine cut granite 16 to 18mm thick ( of any type) work ( table rubbed and polished in steps, jambs, pillars, windows cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

M&L Machine cut marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, treads, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade(any colour/type as per specified by Engr in charge)

Cutting holes into or through cement concrete slabs, chajjas etc reinforced or otherwise superficial area not exc 100 sqcm

S&F aluminium anodised powder coated frame of approved colour coating for doors, window, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified

S&F aluminium anodised powder coated frame of approved colour coating for sliding window two/ three and four track shutter including top. bottom and sides track fixed type with aluminium section medium wieght including necessary joining cleats, glazing clips, stainless steel screws, complete all as specified

S&F aluminium anodised powder coated door/ window & ventilators shutter openable/ sliding type fixed with al sec weighing 0.55 Kg/ mtr incl necessary joining cleats, glazing clips, rubber packing snap beading, screws , handle & tower bolts, roller, incl section of handle, inter locking arrangements, top & bottom of shutter complete all as specified

S&F anodized aluminium door & frame powder coating (minimum thickness of powder coating 50 micron) 2mm thick incl 5.00mm thick tinted glass, fixed with anodized aluminium snap beading, glazing clips, joining clips, screws and 02 Nos of aluminium handle on each door shutter, aluminium anodized tower bolt 200mm long 02 Nos on each shutter and mortice lock device complete with double keys for each lock, 01 No floor spring for each shutter complete all as specified and directed with following specifications :- (a) Aluminium door frame =101.50x44.45mm (b) Aluminium style/top & middle rails of shutter=83.5x44.45mm (c ) Aluminium bottom rail of shutter=114.50x44.45mm (d) Aluminium door frame with shutters shall be fixed in position in PCC block wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed.

S&F 4.8mm thick glass of colour/ tinted pattern of any shapeand size as required & directed by Engr -in- Charge

S&F 4.8mm thick figured glass, pin headed type and glazing with rubber packing, beading in square n exc 0.5 Sqm in each pane all as specified

S&F in repair Mild Steel 4 lever Mortice lock, vertical type, size 100mm

M&L 18/19mm thick Prelaminated particle board, interior grade, but prelaminated both sides with decorative choice laminations fixed with screws to timber/plywood frame/wall frame work

S&F Auto close hinges, stainless steel, bright finish or electrogalvanised.

S & F for Magnetic catcher for doors/cupboards of approved shape and size as per specified and directed by Engr - in - Charge

S&F brass handle of 75mm size type polished bright

S & F framed work as in grills, gratings etc with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors ladders, framed balusters, walk ways etc and fixing complete Fe 290 (Gde-E-165)

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:4 for raising of height of drain, manhole / wall complete all as specified.

M&L scrapping roof surface with wire brushes and washing with water etc including taking down old cement plaster, PCC of any thickness, description in any situation ,position and roof treatment any type for making good to receive new roof treatment any type. and removal of same from site to out side of MOD land complete all as specified and directed.

M&L screed bed or bedding layer of 15mm thick in CM 1:3 for laying floor finishes in roof,laid to provide a finished slope of 1:30 finished even and smooth without using extra cement all as specified & as directed.

M & L fibre reinforced, UV resistant elastomeric liquid applied water proofing & Heat reflective coating, coating with acrylic Polymers and polyester fibres,Smart Care Damp Proof or approved equivalent.The coating shall resist 7 bars of water pressure as per DIN 1048 standards, with elongation of 220% as per ASTM D412 & crack bridging of upto 1 mm & with high SRI value conforming to ASNZ standard. And applying three coat of Elastomeric waterproofing coating with recron fibres & High SRI value (Damp Proof) but first coat of should be as primer for terrace waterproofing. Damp Proof is a part of the DSR as per 22.22A and incl repair and preparing of surfaces of roof and vertical surfaces of walls. The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge.

M&L padding in PCC 1:2:4 type B-0 ( using 12.5mm size graded stone aggregate) laid to provide a finished slope of 1:30 finished even and smooth without using extra cement all as specified

M&L plain cement concrete type B-0, 1:2:4 (12.50mm graded stone aggregate ) in roof kerbs or mud stops, rounded or chamfered on edges

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for including removal of rubbish from the site complete.

M&L cutting groove in brick wall/ stone masonry , 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering

Dismantling wrought iron or mild steel work of any description nototherwise provided for

S & F steel work in tubular/ square/ rectangular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming toIS 1161-1979 graded St-240

M & L Preparing newly untreated steel surfaces of any descripton over 10 cm wiidth or girth and applying two coat of synthetic enamel paints over a coat of red oxide primer

M&L pre- painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

M & L taking down existing treatment of chajja and applying 15mm thick plastering to chajjas in CM 1:3 including making dripping/ throating and PCC 1:2:4 for covering making proper slope etc complete at ground/ first floor all as specified and as directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in stone, concrete block or slab wall.

M & L plain Cement Concrete 1:4:8 type D-2 (40mm graded stone aggregate) in sub base of floors

M & L for preparation of old plastered or unplastered decorated surfaces and applying one coat of white wash on ceiling

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces incluiding filling of depressions etc and applying two coats of oil bound distemper of approved tint.

M&L for 1mm thick wall care putty including preparation of old and new plastered surfaces on walls etc.

M&L for 1mm thick wall care putty including preparation of old and new plastered surfaces on ceilings etc.

M&L for complete removal of existing treatment and preparation of old plastered surface of walls and applying two coat of cement base paint

Dismantling of wall and ceiling board (Fibre, pulp, insulation, etc) or insulation, any thickness, including cover fillets

S&F anodised aluminium snap grid frame work for false ceiling all as specified

S&F hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified

M&L 12mm thick perforated particle board/ tiles for insulation and accoustic purposes, 60cm x 60cm in size, fixed with nails to timber frame work or with staples on snap grid

Taking down carefully surface aluminium or copper point wiring from existing recessed PVC conduits (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces of walls even and smooth using CM 1:3 as required.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame switches, sockets, fan regulators as required for the following :-

One light point controlled by one switch.

One Bulb holder point controlled by one switch.

One fan point controlled by one switch.

One Wall fan point controlled by one switch.

One Exh fan point controlled by one switch.

One bell point controlled by on bell push button

One socket outlet 6 amp controlled by one switch on the same board with other switches.

One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board.

S&F switch modular 1 way 6 Amps, 230 volts, 1 module. Make : Legrand Mylink ™ mechanisms, Cat No : 675501 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular socket 6 Amps, 2/3pin combined 2 module AC 230 volts.Make : Legrand Mylink ™ mechanisms , Cat No 6755 50 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular switch 1 way 16 Amps, 230 volts, 1 module.Make :Legrand Mylink ™ mechanisms, Cat No : 6755 11 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular socket 6/16 Amps, 2/3pin combined 2 module AC 230 volts. Make : Legrand Mylink ™ mechanisms Cat No : 6755 55 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular fan regulator 120 watts, 2-module AC 230 Volts. Make : Legrand Mylink ™ mechanisms Cat No : 6755 31 and equivalent cat part in other makes as per Appendix 'B'.

S&F Modular bell push 6A 1 module Make: Legrand Mylink ™ mechanisms Cat No : 6755 04 and equivalent cat part in other makes as per Appendix 'B'.

S&F bell, AC, 230 volts, single pole. Make : Legrand Cat No : 573443 and equivalent cat part in other makes as per Appendix 'B'.

M&L for TV wiring copper coated steel rurrent capacity 11A , insulation thickness 6.55 mm solid conductor RG-6 CO-axial PVC in black colour drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories in 32 mm dia conduit and terminated in each TV socket all as directed .

S&F TV socket 1 module.Make: Legrand Mylink ™ mechanisms Cat No : 6755 46 and equivalent cat part in other makes as per Appendix 'B'.

M&L for telephone wiring HDPE insulated PVC sheated 2 pair x 0.4 Sqmm grey shaded colour insulation thickness 0.65mm stranded conductor , rurrent capacity 15 A , insulation thickness 6.55 mm solid conductor RG-6 CO-axial PVC in black colour drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories in 20 mm dia conduit and terminated in each RJ 11 telephone socket all as directed .

S&F RJ 11 telephone socket 1 module. Make : Legrand Mylink ™ mechanisms Cat No : 675541 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular whiter cover plate with frame and metal flush box 1/2 module. Make : Legrand Mylink ™ mechanisms Cat No: 6755 61-62 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular white cover plate with frame and metal flush box 3 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 63 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular whiter cover plate with frame and metal flush box 4 module.Make : Legrand Mylink ™ mechanisms Cat No : 6755 64 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular white cover plate with frame and metal flush box 6 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 66 and equivalent cat part in other makes as per Appendix 'B'.

S&F modular white cover plate with frame and metal flush box 8 module. Make : Legrand Mylink ™ mechanisms Cat No : 6755 67 and equivalent cat part in other makes as per Appendix 'B'.

S&F ceiling rose 3 plates polycarbonate body complete. Make: Ancher Penta Cat No : 39017 and equivalent cat part in other makes as per Appendix 'B'.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories size 2X6 sqmm + 1X6 sqmm earth wire in 20 mm dia conduit and including taking down.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories size 4X10sqmm+2X10sqmm earth wire in 32 mm dia conduit and including taking down.

S&F 20 amp, single pole and neutral socket outlet with 2 pole and earthy, metal enclosed plug top in power coated CRCA steel sheet enclosure recess mounted with cchained metal cover for socket outlet with and including one number single pole 'C' series MCB 16 amp as required.

S&F in repair LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2500 lumens/22 watt at a minimum system efficacy of 4000 lumen per 22 watt and total power consumption not more than 40 watt including driver. It has a rated system life time of 25000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Make : Philips Cat Part No : BN 021LED 25S 6500 PSU GR S1 and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair LED fixture 10 watt having lumen output 100 lumens per watt including connection. Make : Philips Cat Part Ref No : BN 021LED 25S 6500 PSU GR S1 and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixing in replacement 8 watts wall mounted LED decorative luminary with standard accessories and lamp inclduing fixing the same with existing wall. Make : Havells Cat Part No. LHJE01106499 and equivalent cat part in other makes as per Appendix 'B'.

S&F in replacement LED post top light 25 Watts in spherical shape polycarbonate diffuser & IP 65 including recessing mounting pipe of size not less than 32mm dia in existing PCC/brick gate post using CM in 1:4 and making connection using 3 core 0.5 Sq.mm PVC insulated cable complete. Make : Bajaj Cat Part No. BLPTSP 25W LED and equivalent cat part in other makes as per Appendix 'B'.

S&F in replcement MCB distribution board, powder coated, TPN , 415 volts, 4 ways,CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required. Make:-Legrand Cat No: 5076/Hager/Schneider as approved.

S&F in replacement MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 volts, 8 ways. Make : Legrand Cat Ref No. 507612 or Schneider Cat No. A9HSND12 and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp. Make - Legrand cat ref no 408587 to 408595 and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Double pole 10 to 32 amp. Make - Legrand cat ref no 4086 14 to 4086 17 and equivalent cat part in other makes as per Appendix 'B'.

S&F in repair MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of TPN 40 to 63 amp. Make - Legrand cat ref no 4086 59 to 4086 61 and equivalent cat part in other makes as per Appendix 'B'.

Supply and fix in replacement LED luminary 35 watts IP 66 5700K outdoor luminary with standard accessories and making connection with existing light point with 3 core 1.0 Sqmm PVC insulated multistranded copper conductor wire including fixing the same on existing Gi bracket complete. Make Philips Cat Ref No . BRP050 LED 036 CW RI MP PCSI PSU GR and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixing in replacement GI bracket made out of 32mm dia GI medium grade pipe of length 90 Cms long bend shape and size as per site requirement including 02 Nos of MS flat 40x5mm 200mm long bend to shape as required to fix the G bracket with existing wall using 04 Nos of MS fastener 10mmx100mm long with nut, bolts and washers complete.

S&F in repair surface mounted LED panel of size 220mmx220mm, 12 watt 1500 lumen output having luminous efficacy >85 Im/W, 6500K, 50Hz, p.f. .0.90, CRI80, THD ,30%, 25000 burning hours including making connection. Make : Philips Cat Part No SM 260C LD 12S-6500 PSU WH and equivalent cat part in other makes as per Appendix 'B'.

Supply and fix 10 watts LED T-lamp B-22 base (warm white/Golden Yellow) 100 lumens, AC 220 volts . Make : Philips Part No. 9290018611 and equivalent cat part in other makes as per Appendix 'B'.

Supply and fixing water heater of 25 liter capacity BEE star rating 5 in approved color, heating element 2.0 KW adjustable temperature setting knob for temparture settings between 25 degree to 75 degree centigrade, outer tank made of non metallic engineering plastic, inner tank made of extra thick superior cold rolled steel provided with high density PUF insulation including 15mm bore 450mm long flexible PVC pipe connection for cold water supply and 15mm bore 450mm long chromium plated metallic flexible pipe connection for hot water supply complete.

S&F LED bulk head fitting 6.5 watt IP 65 & IK 08 with pressure die cast aluminium housing & polycarbonate diffuser duly pre wired connection with 0.75 Sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable all as per Philips Cat Ref No. WT 202W LED 6S PSU NW S2 PC and equivalent cat part in other makes as per Appendix 'B'.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised iron strip 32 x 6 mm earth lead by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6 mm galvanised iron strip

Supply and fixing ceiling fan 1200mm sweep 50 Hz AC 230 volts, 5 star rated in white colour with fan motor, blade set , 0.45 mtr down rod, canopy set, rubber reel including0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No on Fan body as required. Make : Havells Model No . ES-50 and equivalent cat part in other makes as per Appendix 'B'.

Supply and fix in replacement PVC fresh air fan 200 mm sweep with louvers, fan motor and accessories complete including making connections.

S&F Energy meters Three phase , 240V AC, 10-60A, Accuracy cl 1.0 with LPR (Zigbee) enabled meters including suitable size of transprant pilfer proof meter Box push fit & hinge type.Make : HPL Cat No : TLPB 1529131000 OC M0 and equivalent cat part in other makes as per Appendix 'B'.

M/S JALANDRA CONSTRUCTIONS

UNIVERSAL INFRAPROJECT PVT LTD

JAGDAMBA CONSTRUCTION COMPANY