Repair and maintenance of residential and non-residential buildings inside CWS(X) Colony at CWS(X), Talcher for a period of 06 (Six) months.

Part A Civil Portion

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.All kinds of soil

Supplying and filling in plinth with local sand under floors, including watering, ramming, consolidating and dressing complete.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area .5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Brick work with Fly Ash Brick(230x125x75mm size) bricks of class designation 10 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with Fly Ash Brick (230x125x75 mm size) bricks of class designation 10 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster of mix : 1:6 (1cement: 6fine sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing, hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, excluding the cost of required centring, shuttering and cost of reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size).

Cement concrete flooring 1:2:4 (1cement : 2coarse sand : 4graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Second class teak wood. 30 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws

Providing 28 gauge aluminium sheet (to be fixed in doors) as per instruction of EIC.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.75x47x1.70 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing SS wire mesh jali for doors and windows of 22 gauge 18 mesh per sq inch as per instruction of of En ineer-in-charge. Grade 304

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Distempering with 1st quality acrylic washable distemper (ready made) of approved manufacturer and of required shade and colour complete. as per manufacturer's specification.One or more coats on old work

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour:New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm

Renewal of old putty of glass panes (length)

Day to day maintenance of carpentry works by engaging one skilled carpenter and one unskilled Helper as per direction of EIC.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Making tribal art on pre painted wall and specified tree trunks with superior quality weather coat including one coat of background painting of different shae and pictorial figures/witing wh appropriate paint os prominent look including cost of paint,labour,materials ik paint,brush, tools and plants required for the works as per instruction of EIC.

Labour charges including tools and plants for day to day maintenance work like brick work, plastering, flooring and other petty jobs as and when required on daily basis by deploying masons. Beldar /coolie in residential quarters of Colony (Materials to be used in this item are to be paid separately) as per instruction of Engineer-in-charge. (2 Skilled and 2 unskilled worker per day)

Supplying of Portland Cement (Including Carriage)

Supply of Fly ash bricks conforming to I.S. 12894

Supply of river clean sand for miscellaneous works including royalty as per instruction of Engineer-in-charge.

Supplying of 20mm Agreegate for miscellaneous works including royalty as per instruction of Engineer-in-charge.

Supplying of 10mm Agreegate for miscellaneous works including royalty as per instruction of Engineer-in-charge.

Providing welding rod as per instruction of of Engineer-in-charge.

Providing of white cement

Labour charges for day to day maintenance works related with welding works like welding of hinges, welding of flats in window grills and other petty jobs related with welding works as and when required by deploying welder beldar/coolie in residential quarters of colony. (welding rod and electricity is to be provided by the department ) as per instruction of Engineer-in-charge. (1 Skilled and 1 unskilled worker per day)

Carriage of garbage or earth mixed other wastes by tractor trolley including manual loading and unloading and disposing at garbage dumps or at any other specified location as per the direction of Engineer-In-Charge.For a lead of 4.00km

Cleaning of Drains without siltation or sludge deposition: Open Surface drain up to 250 mm wide.(Agency has to clean the relavent drain twice a month)

Cleaning of Drains without siltation or sludge deposition: Open Surface drain above 250 mm width.(Agency has to clean the relavent drain twice a month)

Upkeeping of concrete pavement/ Black topped roads excluding coal transport road by brooming and disposal of collected debris/ waste at collection pit/ dustbins or at specified locations within a lead of 50 metres including all tools & plants like spade, basket,brooms with handle stick complete as per the direction of Engineer-In-Charge. (Agency has to clean the relavent area every altranate day)

Cleaning of non-biological waste such as polythenes, disposals etc from the entire colony and other misc. work as per direction of E.I.C (Agency has to deploy 02 nos unskilled man power daily for a period of 06 months.(Excluding sunday and holday)

Disposal of dead animals like cow,ox,buffalow etc. as an when required including digginhg of pits and buring the same as per instrution of engineer in charge.

Disposal of dead animals like street dog,pigs,cat etc. as an when required including digging of pits and buring the same as per instrution of engineer in charge.

Upkeeping of residential quarters in the township including cleaning of bathrooms, staircase, courtyard, garage, parking space, premises and surrounding areas including collection of garbage and disposal to the dustbins by engaging sufficient numbers of manpower including cost of all necessary tools and supervision charges etc. all complete as per the direction of EIC.D-Type Quarter.

Collection of domestic wastes from indivisiual qtrs on daily basis and loading it in to tractor trolly disposal of waste within a lead of 2 km engaging sufficient number manpower include cost of necessary tools and supervision charges etc all complete as per direction of EIC.(Scope of work : Agency has to deploy 09 nos labour daily & 01 no tractor trolly on daily basis in case of less number of unskilled labour engaged proportionate deduction will be made from R/A bill.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.:All kinds of soil

Clearing grass and removal of the rubbish upto a distance of 50m outside the periphery of the area cleared.

Cutting of grass with grass cutting machine (Operation based on petrol) to required shape as per instruction of the Engr.I/C.

Trimming of trees & cutting of dead part of trees in colony,near other structures etc and disposal of the same at an appropriate place as per instruction of Engg I/c.

Cleaning of roof top area,plucking of unwanted plants,collection of the garbage/algae etc, including disposal of sludge in near by dust bin complete with all tools & plants as per instruction of EIC. (Cost of repairing shall be paid separetly)The agency has to provide unskilled manpower 03(three) during the work to dispose the materials collected from roof to nearby garbage

Removal of chokage / blockage of inspection chambers by removing silt,sludge and other foreign materials and disposal of the same to the nearest dustbins etc. Complete as per the direction of engineer-In-Charge

Removal of chokage / blockage of manholes by removing silt, sludge and other foreign materials and disposal of the same to the nearest dustbins etc. Complete as per the direction of engineer-In-Charge.

Providing PVC SWR pipes conforming to IS : 13592 110 mm dia Type A.

Providing and fixing bolts including nuts and washers complete.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : Above 40 mm nominal bore

Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 150 mm diameter : Class I

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter : Class I

Polythelyne water storage tank with cover and suitable locking arrangement ISI-12701 marked as per instruction of EIC

Providing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid

Providing and fixing PTMT towel rail . 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Providing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing Gun metal gate valve with CI wheels 20 mm of approved quality.

Providing Gun metal gate valve with CI wheels 25 mm of approved quality.

Providing Gun metal gate valve with CI wheels 40 mm of approved quality.

Providing Chlorinated Polyvinyl-Chloride(CPVC)Pipes 20 mm Outer Dia of approved quality

Providing Chlorinated Polyvinyl-Chloride(CPVC)Pipes 25 mm Outer Dia of approved quality

Providing Chlorinated Polyvinyl-Chloride(CPVC)Pipes 40 mm Outer Dia of approved quality

Providing Brass bib cock 15mm of approved quality

Providing Brass stop cock 15mm of approved quality

Providing C.P. bib cock 15mm of approved quality

Providing C.P. stop cock 15mm of approved quality

Providing 15 mm CP brass pillar tap of approved quality by (PLAZA brand or equivalent) as per instruction of EIC.

Providing C.P. Shower of approved quality

Providing Semi Rigid PVC waste pipe for sink and wash basin 32mm dia with length not less than700mm i/c PVC waste fittings of approved quality.

Providing Semi Rigid PVC waste pipe for sink and wash basin 40mm dia with length not less than700mm i/c PVC waste fittings of approved quality.

Providing Unplasticised PVC connection pipe with brass union 30cm long(15mm ) of approved quality.

Providing polythelyne water storage tank cover as per instruction of EIC

Providing pvc washer suitable for brass bib cock and stopcock of approved make as perdirection of EIC.

Providing M.seal adhesive or equivalent (in packet of 100 gm) as per instruction of EIC.

Providing GI clamp of approved make as per instruction of EIC

Providing Brass full way valve with C.I. wheel (screwed end) 50 mm dia.

Providing C.I Sluice valve 80mm dia of approved quality

Providing G.I flange 50mm dia in accordance to confirming ISI specification

Providing G.I flange 80mm dia in accordance to confirming ISI specification

Providing CPVC PLAIN ELBOW- 20mm dia of approved quality as per instruction of Engineer-in-charge.

Providing CPVC TEE - 20mm dia of approved quality as per instruction of Engineer-in-charge.

Providing CPVC UNION - 20mm dia of approved quality as per instruction of Engineer-in-charge.

Providing cpvc brass MTA 20mm of approved make as per direction of EIC

Providing cpvc brass MTA 25 mm of approved make as per direction of EIC

Providing CPVC FTA brass of approved make as per direction of EIC 20 mm dia

Providing CPVC FTA brass of approved make as per direction of EIC 25 mm dia

Providing cpvc solvent of approved make as per instruction of EIC

Hyeginical cleaning of roof top storage tanks of different capacity(750ltr,1000ltr&2000ltr) in both residential and non residential units inside the colony by mixing bleaching powder using plastic brush,plastic brooms and other tool and plants.Cleaning adjacent surrounding area(200mm from periphery of tank),removal of vegetation,weeds if any disposal of wastes at all lift and lead up to 100m(in Dustbins) as per instruction of Engr-in-charge.

Repair and maintenance of all the pipe lines including providing gland packing in valves,replacement of difective pipe lines,changing of ring washer in stop cock,bib cock etc as per instruction of Engr-in-charge.(Excluding cost of pipes,fittings and valves etc)(Agency has to deploy one(01) skilled and 02 no unskilled man power daily for a period of 06 months.(excluding sunday and holiday)

Contractual assistance for deploying 01 (One) Skilled Plumber and 01 (One) unskilled helper for assisting in day to day maintenance works related to plumbing works as per instruction of Engineer-in-charge (On Sunday & Holidays).

Attending electrical maintenance, repairing & breakdown work of residential Quarters & Non- residential Establishments including street lights, underground cables as required and any other work as per instruction of Engineer-in-charge in three shifts(1st, 2nd & 3rd) under the administrative control of CWS(X),Talcher.

Providing of Sub-station attendant/Electrician at "A" and "C" Type colony substation under the administrative control of CWS(X),Talcher.

Providing of S.P. 5/6 amps, one way switch, piano type ISI marked

Providing of S.P. 5/6 amps, two way switch, piano type ISI marked

providing of S.P. 15/16 amps, one way switch, piano type ISI marked

Providing of 3 pin 5/6 amps socket outlet, piano type ISI marked

Providing of 6 pin 15/16 & 5/6 amps socket outlet, piano type ISI marked

Providing of Bell push, piano type

Providing of plug top,5amps,3pin,230Volts of reputed make ISI or Equivalent Mark

Providing of plug top,16amps,3pin,230Volts of reputed make ISI or Equivalent Mark

Providing of Angle Holder, 6amps, 230volts of reputed make ISI or Equivalent Mark

Providing of Stepped type Modular Fan regulator (2 module) ISI or Equivalent Mark

Providing of Ceiling rose, 3 pin, 5 amps ISI marked

Providing of ding dong bell ,230volt of reputed make

Providing of fan capacitor, 2.5mfd, 230volt of reputed make

Providing of 1.5 sq mm PVC insulated multi strand copper cable ,ISI marked, single core of reputed make

Providing of 2.5 sq mm PVC insulated multi strand copper cable ,ISI marked, single core of reputed make

Providing of 4.0 sq mm PVC insulated multi strand copper cable ,ISI marked, single core of reputed make

Providing of 6.0 sq mm PVC insulated multi strand copper cable ,ISI marked, single core of reputed make

Providing of 10 sq mm PVC insulated multi strand copper cable ,ISI marked, single core of reputed make

Providing of 2 core X 6 sqmm CTS aluminium wire, twin core of ISI or Equivalent Mark

Providing of MCB 32Amps, 10KA, C-curve,230volt single pole ISI or Equivalent Mark

Providing of MCB 20Amps, 10KA, C-curve,230volt single pole ISI or Equivalent Mark

Providing of MCB 16Amps, 10KA, C-curve,230volt single pole ISI or Equivalent Mark

Providing of MCB 10Amps, 10KA, C-curve,230volt single pole ISI or Equivalent Mark

Providing of MCB 6Amps, 10KA, C-curve,230volt single pole ISI or Equivalent Mark

Providing of MCB-DP 32Amps, 10KA, C-curve,230volt Double pole ISI or Equivalent Mark

Providing of MCB-DP 63Amps, 10KA, C-curve,230volt Double pole ISI or Equivalent Mark

Providing of 63 amps., 4 pole isolator

Providing of 100 amps., 4 pole isolator

Providing of LED Tube light fitting of 20 watt,230volt BEE 5 Star rating.

Providing of LED bulb pin type of 10 watt, 230volt BEE 5 Star rating.

Providing of PVC board of size 4"X4" With cutting

Providing of PVC board of size 7"X4" With cutting

Providing of PVC board of size 8"X6" With cutting

Providing of PVC board of size 8"X10" With cutting

Providing of PVC board of size 10"X12" With cutting

Providing of 3 mm thick phenolic laminated sheet

Providing of PVC insulated adhesive tape 3/4" ,10mtrs long ISI marked,

Providing of 25 mm dia. ISI marked, PVC conduit

Providing of 20 mm dia. ISI marked, PVC conduit

Providing of 25 mm PVC couplers

Providing of 20 mm PVC couplers

Providing of 20 mm PVC bends BIS confirmed

Providing of 25 mm PVC bends BIS confirmed

Providing of PVC casing caping 1/2" BIS confirmed

Providing of PVC casing caping 3/4" BIS confirmed

Providing of Aluminium lugs for 50 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 70 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 95 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 120 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 150 sq. mm cable

Providing of Aluminium lugs for 185 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 240 sq. mm cable BIS confirmed

Providing of Aluminium lugs for 400 sq. mm cable BIS confirmed

Providing of copper lug socket heavy duty 50 sq mm .BIS confirmed

Providing of copper lug socket heavy duty 70 sq mm .BIS confirmed

Providing of copper lug socket heavy duty 95 sq mm .BIS confirmed

Providing of copper lug socket heavy duty 120 sq mm .BIS confirmed

Providing of copper lug socket heavy duty 240 sq mm .BIS confirmed

Providing of copper lug socket heavy duty 400 sq mm .BIS confirmed

Providing of 4 pole MCCB, 125A, 36KA,ISI or Equvalent Mark

Providing of 4 pole MCCB,250A, 50KA ISI or Equvalent Mark

Providing of SFU 125 Amperes four pole, 440volt with three numbers 125 amperes HRC fuse set in open execution type ISI or Equvalent Mark

Providing of SFU 250 Amperes four pole, 440volt with three numbers 250 amperes HRC fuse set in open execution type ISI or Equvalent Mark

Providing of SFU 125 Amperes four pole, 440volt HRC fuse ISI or Equvalent Mark

Providing of SFU 250 Amperes four pole, 440volt with three numbers 250 amperes HRC fuse set in sheet steel enclosure type ISI or Equvalent Mark

Providing of 90 watt, 230volt LED street light fittings with front toughned glasses cover with IP66 protection ISI or Equvalent Mark

Providing of 180 watt, 230volt LED flood light fittings with front toughned glasses cover with IP66 protection ISI or Equvalent Mark

Providing of Contactor, 4Ploe, 40Amps 440V and (230AV Ac control) for Street light control with IS / IEC Marked

Providing 24 Hour Analog Time Switch (SST* - 15 min) with IS / IEC marked

Supplying of manpower for trimming of trees laying under HT and LT overhead lines of CWS(X) Feeder catering power from 33/11KV Balanda sub station to 2X1MVA main substation of CWS(X), Talcher.

Dismantling, Repairing, Rewinding of ceiling fan/exhaust fan/wall fan complete job as required.

Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil & disposal of surplus excavated soil as directed within a lead of 50 metres.14.2

Total impact of GST plus Labour Cess [@ 1 % (BOCW Cess to be deducted from the RA bill as per the value of the work progress)] for the purpose of CTC