SPL REPAIR TO BLDG NO P-4A (OR MESS) OF HQ MBSC AND PROVN OF WATER PROOFING TREATMENT WITH ALLIED WORKS IN BLDG NO P-222/1 LANCER LINE AND PROVN OF INTERLOCKING TILE NEAR BLDG NO P-301 (IPC) BLDG NO P-276 OF WEU IN THE AREA OF AGE B/R-I UNDER GE AR

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in foundation , filling, sub base and mass concerete complete all as specified and as directed.

M&L 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any description, ( colour, design & pattern, & size/ shape, as approved by GE) as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

Demolition of brick / block or stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 8.00 here-in-above, but except stone.

M&L precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in solid block masonry, 10cm width and setting in cement mortar 1:4 including demolition complete all as specified and as directed .

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

Dismantling, stone slab, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as directed.

M&L sand filling under floor or in foundations including watering and consolidation complete all as specified and as directed.

M&L Spreading and levelling in layers n. exc 25 cm thick and well ramming including watering, complete all as specified and as directed.

M&L Hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L for joint free non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm (size & shape, shade and pattern as approved by GE), as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:3), (including Highlighter pattern), complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid dry or laid dry and pointed complete all as specified and directed.

M&L for machine cut kota stone slab 20 to 25mm thick in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20mm thick screed bed in CM 1:6 including dismantling of stone slabs of any description complete all as specified and as directed.

Machine cut kota stone slab flooring using 20 to 25mm thick slabs,as in shevles (single piece), the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including rounding to edges of kota stone fixed with mortar complete all as specified and as directed.

M&L for 18 to 20 mm thick (telephone black shade) granite stone, as in cooking plateform, oval type WHB counter, sink & etc. machine cut, (table rubbed and polished) best quality as per sample, including & over 20 mm thick screeding in CM1:3 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed.

M&L for 10 mm thick Rendering in CM 1:4 on fair faces of brick work or conc surfaces as in ceilings/chajja/facia & finished even & smooth w/o using extra cement, complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed.

Racking out joints/ pointing to random rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed

M&L keyed pointing in cement mortar (1:3) to squared rubble masonry coursed or un coursed complete all as specified & directed by Engineer-in-charge.

M&L preperartion of newly plastered surfaces on wall and applying two coat of wall putty with fair finished and even surface and applying two coat of oil bound distemper complete all as specified & directed.

M&L for applying 2 mm thick wall care putty on wall surfaces including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper paint on wall surfaces as per manufacturer’s instruction, complete all as specified and directed. Note -i)- Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. ii)- Paint shall be in one or more colours/ shades all as approved by GE.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying three coats of white wash on wall surfaces complete all as specified and as directed.

M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of white wash on wall, complete all as specified and directed.

All as per item No. 32.00 here-in-above, but as on ceiling

M&L preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over a coat of white cement as primer, complete all as specified & directed

M&L for preparation of old decorated wall surfaces plastered or unplastered, by brooming down or steel wire brushing, scrapping down moulds, moss and efflorescent salts and trading oil & greasy spots, including cornices etc and applying one coat of cement base paint on wall, complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over & including M&L single coat of pink primer complete all as specified and as directed .

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each, complete all as directed.

Taking down Shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as specified and as directed.

M&L for rolled mild steel sections like angle, channel, flat, square etc as in framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars ,barred iron doors; ladders ;framed balusters walk ways railings framed work of water tanks and similar work confirming to Fe-290Gde E-165 complete all as specified and as directed.

M & L for mild steel framed work as in brackets etc., for cooler stands /steps/stairs etc., supporting frame work to sunshade, with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel'), complete all as specified and as directed.

S&F mild steel frame work as in stairs ,hand rails half round or other stock section or section or core for wooden hand rail straidgt portion drilled and countershunk for balusters running bars for doors balusters nosing to steps including embeded in concrete and screwing etc hid ties for roof including securing bolts, post and struts in fencing including securing bolts post and struts in fencing including cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillet for necessary drilling boltinh or riveting etc and similar work confirming to Fe-290 Gde E-165, complete all as specified and as directed.

M &L in repairs for fabrication of pressed steel cupboard shutters, using 1.00 mm thick MS plain sheet & frame 1.25 MM thick, bent to shape, including applying two coats of synthetic enamel paint on tint surfaces over & including M&L for two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

M&L factory Made flush shutters, 35 mm thick solid core with block board core construction as per IS 2202(part-I, 1999), both side commercial type. The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 30mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per spec & drawing

M& L for solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

Taking down steel windows and ventilators ( glazed / fly proof) of any description complete all as specified and as directed.

M&L for factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified (with or without cooler opening as directed by engr-in-charge)

All as per item No. 50.00 here-in-above, but without glazing bar.

M&L for factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

All as per item No. 52.00 here-in-above, but without glazing bar.

S&F of aluminium anodised, tower bolt 200 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long, complete all as specified and directed.

S&F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long, complete all as specified and directed.

S &F of stainless steel butt hinges 100 mm size complete all as specified and directed.

S &F of mild steel butt hinges 100 mm size complete all as specified and directed.

S&F 100mm size single action door spring hinge complete all as specified and directed.

S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 140mm long, complete all as specified and directed.

S&F 4.00 mm thick figured glass,pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty/aluminium with rubber beading in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 by using 20 mm graded stone aggregate as in bed block for fixing of hold fast complete all as specified and as directed.

S&F Mild steel work as in hold fasts, clamps, bands, straps or stays, wall ties, hooks etc confirming to Fe - 290, Grade E-165 including prepartion of surfaces and treated with coal tar and sanded with clean sharp sand complete all as specified and as directed.

S&F in replacement decorative type curtain rod stainless steel finish of pipe 22 to 25mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end, complete all as specified and as directed.

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S & F in repairs stainless steel kitchen sink with drainage board, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in repairs white vitreous china squatting pan "Orissa pattern" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap including provision of cement concrete bedding 1:5:10 type E2 complete all as specified and as directed.

S & F in repairs vitreous china ware wash hand basin, white, flat back of size 580 mm X 450 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, complete all as specified and as directed.

Dismantling of cast iron/PVC SWR pipes of 100/110mm bore, including fittings, jointed in cement mortar complete all as specified and as directed.

All as per item No. 72.00 here-in-above, but 75 mm bore pipe

S & F sand cast, cast iron, soil / waste / vent pipes, 100mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

All as per item No. 74.00 here-in-above, but 75 mm bore pipe

All as per item No. 74.00 here-in-above, but fixed to wall with MS clamps

All as per item No. 76.00 here-in-above, but 75 mm bore pipe

S& F 100 mm bore cast iron branch piece, single (single Y) equal or unequal with access door complete all as specified and as directed.

All as per item No. 78.00 here-in-above, but 75 mm bore pipe

S&F100mm CI bends any radius complete all as specified and directed

S&F 75 mm dia CI bend with oval acess door fixed to pipe complete all as specified and directed.

S&F 100mm dia CI vent cowl fixed to pipe complete all as specified and directed.

S & F in repairs 75mm bore cast iron nahani trap with grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S&F in repairs Pillar taps, fancy type Cast copper alloy, with capstan heads chromium plated, screwed down high pressure, with or without lettered 'Hot" or Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15mm bore pipe complete all as specified and as directed.

S&F in repair stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends suitable for 25 mm bore iron pipe or for unions complete all as specified and as directed.

S&F in replacement angular stop cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S&F in replacement bib cock with wall flange, chromium plated brass, fancy type 15mm dia complete all as specified and as directed.

S & F in repair CP central hole basin mixer with regular spout with out popup waste system with 450mm long braided hose with connecting legs and wall flanges complete all as specified and as directed.

Disconnecting existing tanks setting aside [or lowering if required] for repairs,cleaning etc., and hoisting if required reconnecting and refixing in position of water tanks of capacity 500 litres, complete all as specified and as directed.

S&F 500 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

S& F in repair 750 X 1200 X 200 mm thick Stainless steel Plate Racks complete.

M&L 50mm thick PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate for plate form for water tank on roof complete all as specified & directed

Demolition of reinforced cement concrete such as roof, floor slab, beams, stair case, landing, chajjas and similar suspended work and removing rubbish to out side MD land complete all as specified and as directed.

Precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in landings, cover slabs (for man holes etc) chullah hoods,chajjas,water troughs,shelves and similar articles with plain faces complete all as specified and as directed .

S&F 5 cm thick sand stone slabs Jodhpur pattern/colour in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar (1:4) complete all as specified & directed

Taking up or down 25mm bore steel tubing and connections including cleaning for refixing or credited to contractor complete all as specified and directed.

All as per item No 96.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 96.00 here-in-above, but size of pipe 15 mm bore.

S&F GI water tubing medium grade, 25 mm bore size, galvanized, with all fittings fixed to wall, ceilings or laid in floors, complete all as specified and as directed.

All as per item No 99.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 99.00 here-in-above, but size of pipe 15 mm bore size, including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc., complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

M&L for rolled mild steel confirming Fe-290 (Gde E-165) in door or gates of angle other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclding of steel, sheeting or other covering ) rectangular hollow sections. Solid Sq Bars, Flat iron, MS Channel sections , or hollow structural tubes etc incl necessary cutting & bending to shape & welding together complete as in gates , cattle traps , overhead trusses , railings etc as per the design & patterns complete all as directed and hanging also fastening and fixing complete all as specified and as directed.

Dismantling of asbestos cement ( corrugated or semi corrugated etc., ) as in roof coverings complete all as specified and as directed .

M&L Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

Demolition of wall and ceiling boards/PVC wall lining (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work complete all as specified and as directed.

M&L GI frame work size of grid 605 x 605mm for seamless ceiling comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm c/c intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm c/c with GI cleat and steel expansion fasteners with and inccluding ceiling section (not exceeding 1.2M length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel at 457mm c/c and hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and including providing gypsum board 12mm thick in ceiling fixed with screws as per manufacturers instructions over the frame work and preparation of ceiling board and applying two coats of oil bound distemper over a coat of 'Birla' wall / ceiling care putty including dismantling of existing false ceiling of any thickness with cover fillets complete all as specified and as directed.

Demolition of cement concrete as removing existing roof treatment and preparing surfaces to the entire satisfaction of Engr-in Charge /GE including taking down existing plaster, padding,cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc . flushing at junction of parapets complete and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-0 (using 12.50mm graded crushed stone aggregate), as in roof padding over roof for making good depression / undulation to make the existing as filling in depression of roof slab, complete all as specified & directed.

M&L for neat cement slurry @ 3.00 kg/Sqm and screeding / bedding layer of 10 mm thick in CM 1:3 mixed with water proofing compound as per manufacturer instructions over the RCC roof slab for laying of water proofing treatment including providing the following as roof treatment complete all as specified and as directed : - (a) FIRST COURSE: Applying a coat of bituminous primer @ 0.4 litre / Sqm manufactured by the same agency that of APP with a density 0.87 to 0.89 Kg/litre at 25 degree celsius on prepared plastered surfaces. (b) SECOND COURSE: Applying one coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm (c) THIRD COURSE : Provide a layer of APP modified polymeric membrane centre core of 100mm micron HMHDPE, outer film 20 micron each, thickness 2.00mm having weight not less than 3.00 Kg/Sqm, mineral gravel finish on top, using torch application method with minimum 10cm side lap and 15cm end lap complete . (d) FOURTH COURSE : Applying one coat of bonding material using blown type bitumen conforming to IS- 702 grade 85/25 @ 1.20 Kg/Sqm. (e) FIFTH COURSE : 40 mm thick plain cement concrete 1:2:4 (using 20 mm stone crushed aggregate) as in roof padding, including WPC as per manufacturer instruction. NOTE :- 1. A Information Tablet will be put up in the front side wall of the buildings where this work will be done. All building/structure shall be provided with plaque (tablet) furnishing the information as per PS clause, in plaster engraving in and painted as directed by GE 2.WPC shall be measured and paid separately under respective item.

Refixing old GI water tubing of 25 mm bore, medium grade including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

All as per item No 111.00 here-in-above, but size of pipe 20 mm bore.

All as per item No 111.00 here-in-above, but size of pipe 15 mm bore including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc., complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in coping/ benching, DPC, pier caps, bed blocks, for hold fast etc., including mixing with WPC and necessary form work, complete all as specified and as directed. Note:- WPC shall be measured and paid separately.

Supply only integral water proofing compound ISI Marked all as specified.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I, including dismantling taking down old u/s water tank from existing position and credtit to contractor, complete all as specified and as directed.

S&F in repairs PTMT ball valve high pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210 gms, complete all as specified and as directed.

Taking down carefully cement conc /spalled out concrete from RCC roof projections, ceiling ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc, complete all as directed.

M&L for 10 mm thick Rendering in CM 1:3 on fair faces of brick work or conc surfaces as in ceilings/chajja/facia & finished even & smooth w/o using extra cement, complete all as specified and as directed.

S&F in repair GI chicken wire mesh of 0.71 mm dia wire & 12 mm mesh size fixed with nails & screws around RCC chajjaS&Fascias etc., complete all as specified and as directed.

M&L 15 mm thick rendering in cement mortar 1:4 on fair faces of stone or brick work or concrete surfaces mixed with water proofing compound as per manufacturer instructions and finished the surfaces fair and even with out using extra cement complete all as specified and as directed. Note :- WPC will be measured and paid seperately.

M&L for preparation of new plastered wall surfaces and applying two coats of plastic emulsion paint (First quality) over & including M&L for two coats of wall care putty complete all as specified and as directed.

M&L for preparation of new plastered wall surfaces and applying two coats of weather coat paint (First quality) over & including M&L single coat primer, complete all as specified and as directed.

M&L for complete removal of existing treatment of old painted wall surfaces and applying two coats of weather coat paint (First quality) over & including M&L single coat primer, complete all as specified and as directed.

M & L for preparation of old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint of any tint complete all as specified and as directed .

All as per item No. 125.00 here-in-above, but steel surfaces.

Excavating in post holes or similar holes each not n exc 0.50 cu.m,getting out any type of soil, returning,fillig in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete for fencing post complete all as specified and as directed .

M&L prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes confirming to IS:1161-1979 Grade St-240 complete all as specified and as directed.

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in any type of soil complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets,fittings etc., removing materials to store for keeping in safe custody or for taking credit and including cutting, chasing, pinning & making good disturbed surfaces of walls,floors, etc, complete all as specified and directed by Engineer-in-charge.

Taking down un-serviceable DB of any size and capacity including MCB etc, and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls,floors, etc, complete all as specified and directed by Engineer-in-charge.

Taking down unserviceable sub main wiring with copper/aluminium conductor,PVC insulated,unsheathed cable of any size drawn through and including rigid PVC or PVC casing caping including earth wire and making good disturbed surfaces of walls,floors, etc, complete all as specified and directed.

M&L Point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits), with multi stranded copper conductor, nominal cross-sectional area is 1.5 sq mm , single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No.in and including heavy duty drawn through and including in PVC rigid conduit with all accessories complete concealed in wall/roof/floor etc, ISI marked with1.6mm thick mild steel/prestressed steel sunken/concealed box (with earth dolly) duly painted two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for,one way switch One light/ fan/bell point controlled by one, one way switch complete all as specified and directed . Note:- surface conduit shall be laid in ceiling portion only.

All as per Serial Item No.136.00 here-in-above but for one 3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Serial Item No.136.00 here-in-above but for one 3 pin socket outlet 5/6 Amps on the independent board with other switches.

All as per serial Item No.136.00 here-in-above but for AC point on independent board with 4.00 Sqmm cable

S&F piano type Switch 1 way, 6 Amps, flush type, 230 Volts complete all as specified and as directed.

S&F piano type Switch 1 way, 16 Amps, flush type, 230 Volts complete all as specified and as directed.

S&F piano type Socket, 6 Amps, - 2/3 pin combined flush type, 230 Volts complete all as specified and as directed.

S&F piano type Socket, 6 /16 Amps, - 2/3 pin combined flush type, 230 Volts complete all as specified and as directed.

S&F piano type fan step regulator, 120 W - flush type complete all as specified and as directed.

S&F lamp holder, PVC / polycarbonate type with back plate suitable for batten fitting, INCLUDING 9W LED Lamp complete all as specified and as directed.

S&F piano type Ceiling rose, surface bakelite, 3 terminal, 3 phase / PVC / Polycarbonate, isolated body complete all as specified and as directed.

S & F Air circulator fan 450mm sweep, 230 volts, AC Supply and connected with twin core twisted flexible copper conductor cable from ceiling rose to fitting, including taking down 3ft air circulator fan from its position, complete all as specified and as directed.

Supply & replacement of LED light fitting 1X20 Watt (4 feet), decorative ultra slim type, with integral driver, complete with all accessories and making necessary electric connection including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F in replacement bldg security LED Light Luminaire of 35 Watts having IP 65/66 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 160-260 Volts with in built surge protectore, toughened glass with and including GI pipe 20/25mm dia bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.complete all as specified and directed.

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Taking down ceiling fan, any size and sweep from its position ,dismantling for including spray painting of ceiling fan, fan blades, down rod, canopy etc with two coat of synthetic enamel paint of approved colour and quality and marking MES No. etc with black paint, complete all as specified and as directed .

Taking down exhaust fan, any size and sweep from its position ,dismantling for including spray painting of fan, fan blades, down rod, canopy etc with two coat of synthetic enamel paint of approved colour and quality and marking MES No. etc with black paint, complete all as specified and as directed .

S&F Vertical Distribution Board, double Door, suitable for 'A' Frame, incorporating 4 Pole MCCB 100 A to 160A, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way, 415 volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, as in replacement, including taking down old u/s material, complete all as specified and as directed. Note:- MCCB's and MCB's measured and paid seperately.

S&F MCCB, 'A' Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 100 Amp, 4 Pole with over load and short circuit protection, suiatble for item No.124.00, (ISI marked), as in repairs, complete all as specified and as directed.

Supply, fixing, testing and commissioning SP 6 to 32 Amps 240V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

Supply, fixing, testing and commissioning SPN 63 Amps 240V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection, complete all as specified and as directed.

S&F factory made distribution board in sheet metal enclosure in double door with 200A rated bus bar, SPN 12 way, 240V, IP-43 Protection, duly fixed in concealed in wall including cutting chasing pinning, and making good, suitable for for fixing MCB's complete all as specified and as directed.

M&L submain wiring with two runs of 6 sqmm with one run of 6 Sqmm earth wire of 1100V grade FRLSH PVC insulated multi-stranded copper conductor, single core cable conforming to IS 694 drawn through and including cutting chasing in wall for concealed using machine cutting and making good and including M&L 25mm dia non mettalic PVC rigid conduit with wall thickness not less than 1.8 mm, accessories concealed on wall / ceiling with PVC saddles and cadmium plated steel screws and connected to common earth dolly complete all as specified and directed. Note :- Three runs of 6 sqmm and one run of PVC conduit shall be measured as one length for the purpose of measurement.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick burried directly in ground vertically at a depth not less than 2.25 metre deep below normal ground level with top edge of the plate not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and electrode connections by using galvanized iron earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanized iron or steel and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1: 2: 4 type C2 including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 5 of SSR Part I (1991)incl dismanteling of existing unserviceable earth pit all as specified and directed by Engr-in-Charge.

Supply, laying, testing & commissioing of cable XLPE insulated screened PVC beded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 3.50 core including taking out old unserviceable cable if required., complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil all as specified and directed.

Removal of excavated material soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and directed.

Supply and filling dry clean sand (tibba sand) in trenches for cushioning of underground cable and punning for cushioning to cable complete all as specified and directed . Note :- Punned thicknes only shall be measured for the purpose of payment.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type I, flat, size 300 mm x 180mm x 40mm complete laid over the cable perpendicular to the cable for protection, complete all as specified and as directed.

Supply and fix in replacement of GI tubing of size 40mm bore, medium grade for protection of cables on poles / under road crossing complete all as specified and as directed.

NOTE:- (a)- Quantities are clubbed in BOQ for different Jobs. Details as per Annexure-I on Sl. Page No. 41 to 43 of tender document. (b)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

M/S KAUTILYA GARG

Pawan Kumar Shrama Contractor