Spl repair to 04 x Cook Houses T-46 T-51 T-108 and T-109 Drains in North Camp and repair of Garbage Bin in South Camp and North Camp at 274 Transit Camp Khanpur under AGE BR_I South and AGE EM South of GE South Delhi Cantt_10

Amount

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge.

S&F pre-painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws etc. complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and removing rubbish out site the MoD land complete all as specified and directed by Engr-in-Charge.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for coloured glazed ceramic tiles 350x250x7mm/ 450x350x7mm thick in dado/skirting, set and jointed in neat cement slurry & pointed in coloured cement. to match over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removing the rubbish out side the defence land complete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class 'B' Bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L brickwork with sub class 'B' bricks, straight or curved on plan to any radius, as in half brick thick walls, built in cement mortar (1:4.) complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15cm thick (below or above ground level) and removing the rubbish out site the MoD land complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick cement concrete type BO 1:2:4 (using 12.5mm graded stone aggregate) as in floors complete all as specified and directed by Engr-in-Charge.

M&L for machine cut kota stone slab 20-25 mm thick in flooring over and including 20 mm thick cement screed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

All as per srl item No.12 above but vertical surface (such as skirting, dado etc) any height including 10mm thick bedding layer in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and any position not otherwise specifically provided including removing the rubbish out side the defence land complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

All as per srl item No 15 above but 20mm bore.

S&F 15mm bore galvanised iron tubes medium grade with all fittings (such as bend, elbow, tee, union etc) and fixed complete to walls & ceiling or laid in floors complete all as specified & directed by Engr-in-Charge.

All as per srl item No 17 above but 20mm bore.

Refixing old steel tubing 15mm bore and connections in new or old position (walls, ceiling, floor etc.) complete all as specified and directed by Engr-in-Charge.

All as per srl item No 19 above but 20mm bore.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc. and removing the rubbish out site the MoD land complete all as specified and directed by Engr-in-Charge.

M&L for 10 mm thick cement plaster with readymix plaster (as per manufaturer's instruction) on fair faces of brick wall or concrete surfaces finished even and smooth, (without using extra cement) complete all as specified and directed by Engr-in-Charge.

M&L for 15 mm thick cement plaster with readymix plaster (as per manufaturer's instruction) on fair faces of brick wall or concrete surfaces finished even and smooth, (without using extra cement) complete all as specified and directed by Enigneer-in-Charge. Note for item No. 22 & 23:- 1. Make of readymix plaster shall be Birla Aerocon/Ultratech readiplast/ACC Accoplast / Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE) 2. The readymix plaster shall be procured directly from the manufacturer or their authorised dealer. 3 The contractor shall produced original purchase voucher alongwith test certificate of readymix plaster while claiming RAR/ Final Bill.

M&L for preparing newly plastered surface of the wall and applying two coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L for preparing old plastered surface inclucing complete removal of existing treatment of internal wall surfaces and applying two coats of white wash complete all as specified and directed by Engr-in-Charge.

M&L for preparation of plastered or unplastered old extrernal wall surfaces including complete removal of existing treatment and applying two coats of cement base paint complete all as specified and directed by Engr-in-Charge.

S&F mild steel framed works as grills gratings, etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders framed blusters walk ways railings framework of water tanks and similar work conforming to Fe 290 Gde E-165 in chowkats of doors frame etc complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down shutters of any description exc.1 sqm and n exc 2 sqm each and removing to site complete all as specified and directed by Engr-in-Charge.

Taking down and refixing in same opening after any kind of alteration of shutters of any description of exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and directed by Engr-in-Charge.

S&F factory made 30 mm thick flush shutter, solid core consturction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick 2nd class HW plain framed, paneled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete all as specified and directed by Engr-in-Charge.

M&L for preparing newly or previously untreated wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engr-in-Charge.

M&L for preparing old previously old wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F for 300mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cost aluminium alloy complete all as specified and directed by Engr-in-Charge.

S&F for 100mm size of MS butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge.

S&F for 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-Charge.

S&F in repair 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-Charge.

S&F for aluminium, anodised barrel tower bolt of extruded section 200mm of size complete all as specified and directed by Engr-in-Charge.

S&F for aluminium, anodised 100mm size of hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length of cover plate 140mm complete all as specified and directed by Engr-in-Charge.

S&F for mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay with glazing bars, devetailed or welded complete all as specified and directed by Engr-in-Charge.

All as per srl item No 45 above but without glazing bars.

M&L for preparation of newly or previously un treated steel and iron surfaces over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer on steel surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old steel surface over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih SS wire staples complete all as specified and directed by Engr-in-Charge.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih SS wire staples complete all as specified and directed by Engr-in-Charge.

S&F of cast iron casement stays size 300 mm, with hinged joint and two plates with studs complete all as specified and directed by Engr-in-Charge.

Cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement 1:2:4 type B-1 complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and directed by Engr-in-Charge.

M&L for providing cement concrete type B-0, 1:2:4 (using 12.5mm graded aggregate) as in roof kerbs, mud stops, surface channel and drains bed block filling in frames and the like rounded or or chamfered on edges etc. complete all as specified and directed by Engr-in-Charge.

S&F in repairs 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screw to timber frame works including teak wood beading 20mm thick as in shutters of cupboards, shelves, etc complete all as specified and directed by Engr-in-Charge.

S&F for continuous (Piano) hinges, mild steel, bright finish or electro galvanised, width of flaps (when open) in 40mm complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15mm bore bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repairs stop valve 15 mm dia cast chromium plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repairs, CP waste coupling 32 mm dia suitable for wash hand basin or kitchen sink complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type C-2 1:3:6 using 40mm graded aggregate as plinth protection finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.5 mtr wide & n.exc 1.5 mtr in depth for foundation etc in hard/dense soil complete all as specified and directed by Engr-in-Charge.

Surface excavation in soft/loose soil n.exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed by Engr-in-Charge.

M&L for hard core of gauge of n.exc 63 mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified and directed by Engr-in-Charge.

S&F steel work in tublar trusses, posts raffers, purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161- 1979 Gde St-240 complete all as specified and directed by Engr-in-Charge.

S&F in repairs 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, including brackets for bottom support fixing with gitties embeded in wall with drilling machine etc. complete all as specified and directed by Engr-in-Charge.

S&F vitreous china squatting pan (Orissa pattern) long pan including provision of lime concrete bedding fixed in repair size 580x440mm white with intergral footrest with 'P' or 'S' trap (excluding flushing cistern and flush) complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in floors complete all as specified and directed by Engr-in-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, cills, steps, seismic, and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs for water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:4:8 type D-2 (Using 40mm grd agg) as in mass concrete as in foundation complete all as specified and directed by Engr-in-Charge.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, surface is to be finished even and smooth (with using extra cement including one coat of primer) complete all as specified and directed by Engr-in-Charge.

Taking down carefully the old u/s Aluminium point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete.

M&L for point wiring complete, standard copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in and including suitable concealed PVC conduit medium grade and sunk in pressed steel terminal boxes of required size with top cover 3 mm thick plastic/laminated sheet of required color with screwed and cup washer complete with all accessories including 1.5 Sqmm standard copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and directed by Engr-in-Charge. Note :- The Rate is inclusive cutting/chasing and making good distrubed surface with CM 1:3 and same surface finishes with the adjoining surface of distribed area with ODB/colour wash/white wash complete. (a) One light/Fan/Bell Point/Security light controlled by one way switch.

All as per above Srl item No.75 but one 3 pin socket outlet 5 Amps independent board.

All as per above Srl item No.75 but one 3 pin socket outlet 5 Amps point on same board.

All as per above Srl item No.75 but one 3 pin socket outlet, 15 Amps on independent board with cable 2.5 Sqmm for main current and 2.5 sqmm as earth wire for power point.

S&F switch piano, flush type 5 Amps single pole one way complete all as specified and directed by Engr-in-Charge.

S&F socket piano, flush type 5 Amps single pole one way complete all as specified and directed by Engr-in-Charge.

S&F switch piano, flush type 15 Amps single pole one way complete all as specified and directed by Engr-in-Charge.

S&F socket piano, flush type 15 Amps single pole one way complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose surface Bakelite 60x25 mm two to three terminals complete all as specified and directed by Engr-in-Charge.

S&F ceiling fan regulator electronic type complete all as specified and directed by Engr-in-Charge.

S&F in replacement of LED Batten T-5 fitting 20 watt LED White, indoor decorative aluminum extruded T-5 LED battern integrated type environmental friendly complete all as specified and directed by Engr-in-Charge.

S&F in replacement RUGBY Bulkhead suitable for LED 09 Watt of Base B22, Bulk head in die cast aluminium housing & frosted glass including all accessories connecting up twisted flexible copper conductor cable of suitable size of 230 V, 50 Hz complete all as specified and directed by Engr-in-Charge.

S&F in replacement for Batten holder with PVC body and back plate suitable for LED Bulb B-22 cap complete all as specified and directed by Engr-in-Charge.

S&F in replacement LED RETROFIT Lamp of 9 Watt for fixing in batten holder/wall mounting/bulkhead point complete all as specified and directed by Engr-in-Charge.

S&F in replacement LED Inverter based 45 Watt made street light fitting complete with accessories made of aluminium housing having minimum system efficiency 100 Lm/watt operating at full load at AC supply & minimum 20 watt during battery backup,power factor is equal to or greater than .95,CCT 6500K, CRI-80, IP-20, inbuilt Li-ion battery for backup, backup up to 4 hrs for complete tube light (partial backup not allowed), LM-80 certified complete all as specified and directed by Engr-in-Charge. Make : Cat Part No.HLSLD-ML04-45-CWL-INV of Halonix or its equivalent as specified make. Note : (i) Contractor should be provided minimum two year warranty from the date of supply of item.

Taking down of old serviceable ceiling fans, dismantling of blades, greasing, oiling and cleaning of blades, keeping in safe custody and refixing it back after completion of rewiring work complete all as specified and directed by Engr-in-Charge.

Taking down of old unserviceable ceiling fan/exhaust fan any type and size, dismantling the blades, transportation to civil work shop for rewinding and refixing it back after completion of rewiring complete all as specified and directed by Engr-in-Charge. Note : Rewinding will be measured and paid under respective item of this Schedule.

M&L for Rewinding of ceiling fan 1200/1400 mm sweep by dismantling of fan motor cutting and removing of burnt windings, cleaning, winding with supper enameled copper wire of superior quality, same gauge of wire, same Nos of turns, provn of insulation paper applying of varnish drying of varnish and assembling of fan including replacement gun metal bush and Shaft where ever required complete all as specified and directed by Engr-in-Charge.

M&L for Rewinding of exhaust fan 450 mm sweep by dismantling of fan motor cutting and removing of burnt windings, cleaning, winding with supper enameled copper wire of superior quality, same gauge of wire, same Nos of turns, provn of insulation paper applying of varnish drying of varnish and assembling of fan including replacement gun metal bush and Shaft where ever required complete all as specified and directed by Engr-in-Charge.

S&F in replacement sheet metal enclousure for DB's where MCB's to be used Single pole and Neutral 12 way, 240 volts, double door bus bar neutral link, earth bar and din rail complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCB SPN 63 Amps 'C' curve 240 volts complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCB SP 6 to 32 Amps, 'B' curve 240 volts complete all as specified and directed by Engr-in-Charge.

M&L in replacement of earthing complete with galvanised steel earth plate 600X600X6 mm thick buried directly in ground (earth pit not les than 2.25 M deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI earth lead wire 4.0 mm as earthing leads by means of bolts, nuts, check nuts and washers all joints as shown on drawings and including excavation, earth work. GI pipe light grade 15 mm bore for protection of GI earth wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt PCC (1:2:4) type B1chamber and MS angle iron frame of 40mmx40mm x3 mmand RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No 3 of SSR Part-I and conected to earth test point including testing complete all as specified and directed by Engr-in-Charge.

M&L for laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm x 2 core complete all as specified and directed by Engr-in-Charge.

Excavation in trenches of any type of soil n.exc 1.5 mtr in width and n.exc 1.5 mtr in depth and getting out soil for laying of cables, Foundation filling of poles or stays complete all as specified and directed by Engr-in-Charge.

Returning filling, in including spreading, leveling, watering and well ramming in layers not exc 25 cm each complete all as specified and directed by Engr-in-Charge.

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Supply and spreading fine sand (Jamuna sand) in trenches for cushioning of cable 8 cm thick below the cable and 15 cm thick above the cable complete all as specified and directed by Engineer-in-Charge. Note: After punning down 18 cm shall be measured for payment.

Supply and laying sub class ‘B’ bricks well burnt for cable protections laid flat with length equal to width of brick over cable perpendicular to length of cable complete all as specified and directed by Engr-in-Charge.

Supply and laying in replacement galvanised steel tube (GI) light grade of size 40 mm (1.5") bore fixed to walls and ceilings or laid in trenches complete all as specified and directed by Engr-in-Charge. Note:-The rate is inclusive of PCC work and making good the disturbed surface of ceiling ,wall, road etc.

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

JINDAL ENTERPRISES

M/S Sahil Infrastructures

Chaudhary Constructions

PD SHARMA AND SONS