8125/SAR-T-66/2025-26 SPECIAL REPAIR OF ALERT STORE BUILDING NO T-2 AT SG, WORKS SERVICES FOR SETTING-UP OF HYDRAULIC LAB, REPAIR/RENOVATION OF RUNWAY TAXI EDGE SYSTEM AT AIRWING AT ARC AND PROVN OF WASHROOM AT LGS SECTION AT AF STN SARSAWA UNDER GE

Amount

Excavating in trenches, not exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed. Note :- Soil obtained from excavation under item 2.00 here-in-before shall be used for filling.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25cm in soft / loose soil complete all as specified and directed.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in concrete in ground floor pavings n. exc 15 cm thickness (below or above ground level) and removal of rubbish materials complete all as specified and directed.

M & L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified and directed.

M & L for 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), as in levelling coarse for tiles complete all as specified and directed.

M & L for reinforced concrete M-25(Nominal Mix) (using 20mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slab and in shelves and the like complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar works n. exc 200mm thick of flat surface, finished surfaces etc complete all as specified and directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed by Engr-in-Charge.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed.

M & L for brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar (1:4) complete all as specified and directed.

M & L for rendring 10mm thick on fair faces of brick work or concrete surfaces on wall in cement mortar (1:6) complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces on ceiling in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces and distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gsm/ltr of approved manufacturer of required shade and colour complete all as per manufacturer's instructions two or more coats on new work complete all as specified and directed.

M & L for preparation of new plastered surfaces and applying two coat exterior emulsion paint over a coat of primer paint complete all as specified and as directed any tint complete all as specified and directed.

M & L Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to TMT bar complete all as specified and directed.

S & F mild steel TMT bars 5 mm dia & over upto 10 mm as in stirrups, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & screwed complete all as specified and directed.

S & F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S & F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified and directed.

S&F anodized aluminium Powder coated door shutters, aluminium section weighing 0.55 kg/m, with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc complete all as specified and directed.

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement complete all as specified and directed.

S&F door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) suitable for door shutters of 701 to 850mm in width aand weight between 36 to 60 Kg and fixed complete all as specified directed.

S & F brass mortice lock, verticle type, size 100mm, 4 levers with escutheon plates & two keys in aluminum frame complete all as specified and directed.

S & F 140mm floor door stopper aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor but of brass body and tongue with hard drawn steel spring complete all as specified and directed.

M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed.

M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on verticle surfaces such as dado. skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and over 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M & L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cement mortar (1:4) complete all as specified and directed.

S&F 5mm thick frosted glass with rubber bedding in square n exc 0.5 sq.m in each pane complete all as specified and directed.

S & F prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws but prelaminated both side with decorative choice lamination complete all as specified and directed.

S & F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed.

S & F steel tubing medium grade 20mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed.

M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L for false ceiling made out of E-board classic of size 600 x 600 x 4 mm thick, GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 26.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with Gl wire 3 mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scaltings 40 Sq. cm and over in section in any position for unframed works complete all as specified and directed.

Demolition of roofs, floors (other than ground floor) beams, staircases, landings, chajjas and similar suspended works complete all as specified and directed.

M & L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S & F steel tubular trusses including special shaped washer framed work such as in doors or gate of angle or other section with gusset plates, braces etc. with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars , barred iron dooetc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

M & L for painting to new or previously untreated steel & iron surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint (any colour) over a coat of zinc chromic primer including preparation of surfaces complete all as specified and directed.

M & L for 25mm thick PCC (1:2:4) type B-1 (using 20mm graded mechanically crushed stone aggregate), as in sub base for tiling work complete all as specified and directed.

M & L coloured non skid ceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed.

M & L brick work sub class 'B' bricks (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L rendering 15mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed.

M & L for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces incl 1mm thick wall care putty complete all as specified and directed.

M & L for 75mm thick cement concrete type C- 2, 1:3:6 (using 40mm graded stone aggregate) as in plinth protection complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 10 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Taking down chowkhats or frames not exceeding 1.5 sqm each with shutters (without taking off shutters from the frame) and removing from site including cutting holes required for taking out existing hold fast complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 sqm but not exceeding 4.00 Sqm with shutters (without taking off shutters from the frame) and removing from site including cutting holes required for taking out existing hold fast etc complete all as specified and directed.

S & F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified supplied and fixed complete all as specified and directed.

S & F 40mm thk Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 35mm thick second class, hard wood(hollock), glazed and skeleton shutter, open rebated and prepared to receive glass/guage etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as sepcified and directed.

S & F cold rolled mild steel butt hinges 100mm long medium weight to pressed steel/angle iron frames by welding/screwes complete all as specified & directed.

S & F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 150mm Extruded aluminium alloy handles, fabricated type, anodised complete all as speicfied and directed.

S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S & F anodized aluminium window and ventilator shutters side hung type/sliding type without sash bars, aluminium section weighing not less than 0.55 kg/m with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminum snap beading screws anodized aluminium fittings such as peg stays 150mm long (01 No.) hinges type B-21 100mm long (02 Nos.) suitable handle (01 No.) complete all as specified and directed.

M & L 4.8/5mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm each pane complete all as specified and directed.

M & L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for reinforced cement concrete M-25 (Nominal mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams,plinth beams, bases for columns, mass concrete and the like complete all as specified and directed. Note: Reinforcement & formwork shall be measured and paid for separately.

M & L for Reinforced cement concrete (nominal mix) in Type B1 (1:2:4) (using 20 mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M & L formwork to sides of concrete foundations, footings bases of columns, plinth beams etc complete all as specified and directed.

M & L formwork to sides & soffits of beams, bands, archs, flat, curved, noising, cornices in step manners as directed & the like of concrete complete all as specified and directed.

S & F 150mm x 150 mm salt glazed stone ware gully traps, square or round mounted, type 'P' including dismantaling old trap complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1mm thick wall care putty of approved tint complete all as specified and directed.

M & L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed.

S & F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/laid in trenches including removing the old pipes and making good the disturbed surface as per existing complete all as specified and directed.

All as per Item No 76.00 here-in-above but for floors complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified and directed.

S & F in repair 75mm bore PVC (SWR) bends any radius complete all as specified.

All as per Item No 79.00 here-in-above but for floors complete all as specified and directed.

S & F in repair 110mm bore PVC (SWR) bends any radius complete all as specified.

S & F in repair 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified and directed.

S & F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 20 mm dia complete all as specified and directed.

S & F fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F angle valves, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified and directed.

S & F Stop valves, 15mm bore cast copper alloy,screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F Vitreous China Squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rests connection to trap and to flushing pipe, etc complete including making food to floor complete all as specified and directed.

S & F chromium plated Brass health faucet for EWC with including PVC Connection 1m long suitable for 15mm bore with all connected fittings complete all as specified and directed.

S & F PVC valveless, syphonic action type, flushing cistern of 10 ltrs capacity low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed.

S & F vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F VITREOUS ladies urinal for bathroom size of 45x35.5x10cm including connection complete all as specified and directed.

S & F Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified and directed.

S & F PVC connection of 15mm bore with 2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe complete all as specified and directed.

M & L for clamps , hold fasts; wall ties, plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts plate washers and similar small articles conforming to Fe-290 Gde-E-165 (R) complete all as specified and directed.

S & F MS grating CP 100 mm dia, and including floor trap with hole/without for waste pipe of approved make including fixing with CM to floor/nahani traps and including dismentling old unsv grating/traps complete all as specified and directed.

S & F vitreous china Counter top wash basin white, flat back, size 550x400mm including fancy type pillar tap brass CP 15mm bore with long screwed shanks and fly nuts waste coupling brass CP 32mm bore, flange end bedded in red lead cement and other end fixed and PVC connection 450mm long 15mm bore with 2 Nos nuts and washes CI brackets complete all as specified and directed.

S & F Brass CP Soap Dispenser with Glass Bottle complete all as specified and directed.

S & F 18/19mm thick High Density High Moisture Resistant board (HDHMR) Prelaminated both sides as in Controller's Desk ,palmed boxes, showcase, shutters of Cup Boards, drawer fixed with MS heavy duty telescopic slide channel of any size etc including 6mm designing teak wood beading on edges complete all as specified and directed.

S & F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to wall complete all as specified and directed.

M & L for providing and laying prepolished cement concrete Chequered tiles 30cm x 30cm x 25mm thick, with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape heavy duty , set,jointed and pointed in neat cement slurry in floors over screed bed 15mm thick (1:6) cement mortar complete all as specified and directed.

S & F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment AFe- 290(Gde E-165) on any hight complete all as specified and directed.

M & L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified and directed.

M & L for flame proof wiring with single core PVC insulated and unsheathed 1100 volt grade FRLS electric cable with multi stranded copper conductor of size 2.5 Sqmm phase and neutral drawn in and including ERW rigid steel stove enameled black conduit heavy duty ISI marked of size 20mm dia on surface/wall/ceiling including all flame proof conduct fittings and accessories such as tees junction boxes, bends duly tested by CMRI Dhanbad suitable for one light /fan point controlled by one flame proof rotary switch SP one way and including drawing continuous earth wire FRLS PVC insulated unsheathed 1100v grade cable with stranded copper conductor of size 2.5 Sqmm and connected to earth dolly complete all as specified and directed.

S & F flame proof/weather proof direct entry type rotary switch single pole on & OFF rotary motion switch in cast aluminum alloy LM-6 enclosure epoxy powder coated single pole 230Volts 10 Amps, AC ON/OFF switch operated externally by Knob having 02 Nos of M-20 cable entries, earthing terminals suitable for mounting on Wall/Steel structure etc complete all as specified and directed.

S & F in replacement of LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver,holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. Note: (a) All fittings shall be ISI marked and shall have approval of CMRI Dhanbad . (b) Original Test certificate of Manufacturer shall be produced by Contractor .

S & F flame proof switch /socket and plug combined in LM6 cable termination box in LM6, 25A, 230V, 2P + earth complete all as specified and directed.

S & F flame proof exhaust fan 300mm sweep single phase including frame motor blade and all accessories and making of hole in brick work, wooden/ aluminum window complete all as specified and directed.

Supply, install, testing and commissioning of flame proof totally enclosed TPN DB 4 way complete with CMRI certified and flame proof, weather proof complete with emergency off switch with LED indicator as per incomming and outgoing circuits complete all as specified and directed. Incomming: (a) MCB TPN 63 Amps-01 No, 4 pole complete with 10 KA breaking capacity and B curve-01 No. Outgoing: (a) MCB SP 6 Amps with 10 KA breaking capacity and B curve-02 No (light points). (b) MCB SP 10 Amps with 10 KA breaking capacity and B curve-10 No (flood light).

Supply, laying and testing of XLPE cable insulated screened, PVC bedded, galvanised steel strip or wire armoured electic power cable (heavy duty) 1100 Volts grade with standard aluminum conductor of size 10 Sqmm 4 core complete all as specified and directed.

M & L for boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 25mm dia suitable for 0.4 mps working pressure complete all as specified and directed.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified and directed.

M & L for common burnt clay bricks, sub class 'B' grade laid in trenches for protection of UG cables perpendicular to the direction of the cables complete all as specified and directed.

M & L for dry sand cushioning with layer of dry, clean & fine sand 8cm thick before laying of cable and 15 cm thick after laying of cable in trenches complete all as specified and directed.

S & F in eplacement of GI pipe light grade of size 40 mm bore with all fittings such as socket, union etc laid in trenches/pole/ wall for protection of cables complete all as specified and directed.

Supply, installation, testing and commissioning of split type AC with indoor/oudoor unit complete with cordless remote control unit indl all accessories and within built air inoiser and plasma filter for better indoor air quality of capacity 1.5TR minium 3 star rating and EER 3.2 complete all as specified and directed.

S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and directed. Note: (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F in replacement of single pole and neutral enclosure with 2 pin and metal earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

S & F automatic voltage stablizer 4 KVA, ISI marked digital wall mount, input voltage 160-260V, rated output volatge stablizer 195-245, rated current 14.5 amp, insulation class B suitable for 1.5 ton air conditioner with inbuilt electric overlad trip, protection against high /low volatge & timer for 10 secong including effiecincy more than 97% complete all as specified and directed.

Taking down carefully copper / aluminium point wiring light / fan, socket or power point complete including fittings such as switches, sockets, ceiling rose, bell push bell buzzer lamp holder bracket etc. removing from site and making good disturbed surface of wall, floor etc complete all as specified and directed.

M & L for concealed point wiring (in replacement, if needed) complete with PVC insulated and unsheathed FRLS cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia, with MS stove enamelled sunken boxes (normal and modular type as required) including earth dolly with plastic laminated sheet top cover (cover plate with frame in case of modular) of approved make and colour including 1.5 sqmm multi stranded FRLS copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified and directed for the followings :- One light / fan point controlled by one way switch

All as per Item No 121.00 here-in-above but for one 5 Amp socket outlet on independent board complete all as specified and directed.

All as per Item No 121.00 here-in-above but for one 5 Amp socket outlet on same board complete all as specified and directed.

All as per Item No 121.00 here-in-above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, FRLS cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified and directed.

S & F socket outlet 6A-2/3 Pin combined 2 module modular type complete all as specified and directed.

S & F socket outlet 6A/16A-2/3 pin combined 2 module modular type complete all as specified and directed.

S & F switch 6 amps modular type one one way complete all as specified and directed.

S & F switch 16 amps modular type one one way complete all as specified and directed.

S & F in replacement of Lamp holder bakalite type with back plate suitable for batten fittings complete all as specified and directed.

S & F in replacement/new ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and directed.

S & F MCB SP 5 to 32 Amps, 240 volts curve 'B', breaking capacity 10KA complete all as specified and directed.

S & F MCB SPN 16 to 32 Amps, 240 volts curve 'B', breaking capacity 10KA complete all as specified and directed.

S & F modular Fan Regulator fan step regulator,120W- single module ISI Marked complete all as specified and directed.

S & F modular blanking plate, 1 module ISI Marked complete all as specified and directed.

S & F in repair of Earthing to DBs with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth lead 4.0 sqmm galvanised iron wire by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead shall be protected by GI pipe 15 mm dia medium grade and connected to distribution board including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and directed.

S & F in repair for Earth continuity conductor or main earthing lead of 4.0 Sqmm galvanized iron wire, buried in ground or fixed to wall in and including 15 mm bore GI pipe medium grade for protection of earth wire complete all as specified and directed.

S & F in replacement enviroment friendly,ultra modern,energy saving surface mounted decorative 10 Watt LED bulkhead fitting modular type with polycarbonate housing ,high efficient LEDs with opal diffuser and IP65 protectio, lumen efficacy 85 lm/watt with colour temerature 6500K, THD≤ 20 CRI>80,2.5 kV surge protection complete all as specified and directed.

S & F in replacement enviroment friendly recess/surface mounting 36 watt LED flat panel 2'x2' fabricated CRCA sheet steel duly powder coated housing cool white with high efficient LEDs & glare free opal diffuser PF>0.95 , lumen efficacy>100 lm/W, THD<10% operating range 220v to 240V,CRI>80 including connection with existing wire and all accessories complete all as specified and directed.

S & F in replacement enviroment friendly recess/surface mounting 20 watt LED flat panel 1'x1' fabricated CRCA sheet steel duly powder coated housing cool white with high efficient LEDs & glare free opal diffuser PF>0.95 , lumen efficacy>100 lm/W, THD<10% operating range 220v to 240V,CRI>80 including connection with existing wire and all accessories complete all as specified and directed.

S & F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S & F plastic body ventilation exhaust fan 250 mm, 50 Hz, 240 volt 1250 RPM with copper wound motor including all fixing accessories complete all as specified and directed.

Supply, and Installation of meeting ICAO Annex - 14 Requirement of elevated type taxiway edge light LED Based fitting inncluding 2 pin secondary lead plug 2.5 sqmm copper with breakable coupling, mounting flange assembly, gasket, with 6 nos. stainless steel bolts, spring & plain washer etc confirming to particular specification complete all as required with 2 Years warranty on material Quality complete all as specified and directed.

Supply and Installation of meeting ICAO Annex - 14 Requirement 5 kV grade 50 Hz isolating transformers, series type encapsulated in neoprene tube rubber with primaryand secondary leads as specified in particular specifications etc as required complete all as specified and directed. (a) Supply only Taxiway edge light fitting 45 Watt, 6.6 Amps with LED amp and breakable coupling complete as per ICAO standard.

Supply and Installation of 5 kV grade plug and receptacle of type-I Class B connector and suitable for field attachment with 5 kVgrade PVC insulated, PVC sheathed single core copper conductor of following sizes cable conforming to the particular specifications as required complete all as specified and directed.

Installation, commissioning and testing including taking down of above items (Item No 143.00 to 145.00) as dierected including necessary digging, PCC and earth work complete all as specified and directed.

Supply & install, testing and commissioning in replacement of outdoor type floor mounted LT panel suitable for 415 volts, 3 Phase 4 wire, 50 Hz AC supply sysytem conforming to IS : 8623/93, floor mounted, factory made, weather and vermin proof, fully ventilated and fabricated out of angle iron 40mm X 40mm X 6mm thick frame work and CRCA sheet 3mm thick having Aluminum bus bar of rating 600 Amps,three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeves. The size of the outer shell should not less than 1000mm X 750mmX 500mm, mounted on angle iron stand made out of size 40mm X 40mm X 6mm grouted of digital volt meter & Amps meter with CTs including taking down of old existing panel complete all as specified and directed. Note: (a) Bus bar chamber of 3 phase and 1 neutral 4 strip 415 volts with 600 Amps aluminium strip - 1 Set (b) MCCB 400 Amp 35 KA 4 pole - 01 No ( Incoming) (c) MCCB 100 Amp 35 KA 4 pole - 02 No (Outgoing) (d) MCCB 63 Amp 25 KA 4 pole - 05 Nos(Outgoing) (e) Volt meter digital 0-500 volt =01 (f) Amp meter digital 0-300 Amp = 01 (g) Indicator lamp Yellow, Red, Blue - 01 Set

Supply and Laying XLPE insulated galvanised steel strip or wire armoured elctric power cable with stranded aluminium conductor 1100 Volts grade of size 95 sqmm 3.5 core complete all as specified and directed.

S & F switch piano type 5 Amps one way ISI marked complete all as specified and directed.

S & F socket outlet 5 pin, 5 Amps flush type complete all as specified and directed.

S & F of enviroment friendly, ultra modern, energy saving sindoor decorative 20 Watt LED polycarbonate batten with opal diffuser, operating voltage range 140 V to 270 V, driver efficiency 88%, lumen efficiancy =100 lm/watt with colour temerature 6500K, THD≤ 20 CRI>80,2.5 kV surge protection with zero mercury content including all accessories complete all as specified and directed.

S & F LED light fitting mirror type high output diffuser 2 feet, 10 watt, 220 V AC decorative type with driver holder and LED lamps suitable complete all as specifed and directed.

S & F exhaust fan, steel body AC single phase 230 V of size 300 mm sweep with 1400 RPM, double bearing blades and frame and louvers complete with making arrangments for fixing of exhaust fan on steel/ aluminum frame window/ making opening in brick wall as per site requirement and also making good to disturbed surfaces as per matching to existing one complete all as specified and directed.

S & F wall mounting fan 230V, single phase 400mm sweep in size with complete accessories complete all as specified and directed.

Supplying and laying of GI pipes medium class of size 25 mm dia including fittings complete all as specified and directed.

S & F 25mm dia gun metal gate valve screwed complete all as specified and directed.

BRIJ CONSTRUCTIONS (BID ID -3485957)