SPL REPAIR TO B/R AND E/M WORKS IN CERTAIN BLDGS ALONGWITH PROVN OF OTHER REV/MINOR IN VARIOUS UNITS AT SUNDERBANI UNDER GE (N) AKHNOOR

Amount

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified and directed.

Rendering 15mm thick cement plaster with cement mortar(1:4) on fair faces of brickwork or concrete surfaces and finished even and smooth without using extra cement using water proofing compound.(WPC shall be measured and paid seperately) complete all as specified and directed.

Rendering 15mm thick cement plaster with cement mortar (1:6) on other than fair faces of brick work or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick cement plaster with cement mortar (1:6) on fair faces of brickwork or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Supply only Integral water proofing compound.

Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including chalk whiting primer, complete as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of approved primer (alkali resistant priming complete, all as specified and directed.

Preparation of old distempered/painted surfaces of wall including washing, rubbing down, stopping of surfaces and applying two coats of oil emulsion distemper, complete as specified and directed.

Preparation of plastered or unplastered surfaces of wall by washing, rubbing down and stopping of distempered and painted surfaces and applying two coats of cement based paint all as specified and directed.

50mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finishing the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section, as in any position, complete all as specified and directed.

Dismantling timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc , complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets all as specified and directed.

4mm thick fibre cement E-board designer pattern (classic) ISI Marked IS-14862-2000 of size 600x600mm as in false ceiling fixed with GI frame work grid of comprising of main runner size as GI Tee of size 24x32x3mm as main runner, 28x24x3mm thick GI Tee as cross runner and GI angle of size 24x24x4mm as the wall perimeter including GI adjustable suspenser 4mm wire of required length hange with ceiling with accessories like butterfly clips etc all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling of asbestos, cement (corrugated, semicorrugated, etc.) sheets in roof coverings , complelet all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter, ridge & similar works fixed with self tapping screws complete all as specified.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

Mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-250 Gde E-165, complete all as specified and directed.

Rolled mild steel sections as in gusset plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk foring holes, without any attachement conforming to Fe 410-W(Gde E- 250)quality A , complete all as specified and directed..

Rolled mild steel Joist,channel angle or tee sections fixed independently without connecting plates etc (cut to ordinary lengths i.e with in 20mm of the length indicated) confirming FE 410 W Gde E 250 quality A complete all as specified and directed.

Mild steel screw bolts 5-10mm dia at neck, machine made, with hexagonal or square heads at one end and screwed the other, or screwed both ends; each screwed and to be fitted with washers and one hexagonal or square nut not exceeding 5cm long, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

Walling of random rubble stone masonry uncoursed , well bonded, bedded and solidly hearted, built in cement mortar (1:4), complete all as specified and directed.

All as per ser Item No 27 above but except stone, complete all specified and directed

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base to floor & finishing surfaces even and rough, complete all as specified and directed.

Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

Glazed ceramic coloured tiles (450x300mm)/(600x300mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified.

Factory made Pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc.complete including bottom of each chowkat to be welded with 01 No 25x3mm thick flat iron projecting 10cm on either side & tarring back of chowkats and holdfasts with & including PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified & directed.

35mm thick 2nd class hard wood factory made plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board with commercial face veneers fitted to chowkats of size as IS-1003 Part-I, kiln seasoned and chemically pressure treated, complete all as specified and directed.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer,complete, all as specified and directed.

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( gauzed & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item

Description all as per Item No.40 above, but only fixed glass pane shutter without glazing bars.

Description all as per Item No 40 here-in-before, but only glass pane shutter without glazing bars hinged at top for ventilator.

Mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, and similar works,complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe-290 (Gde E 165), complete all as specified and directed.

Preparation of new or previous un-treated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples,complete all as specified and directed.

Factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplied & fixing in opening as per specification & drawing complete all as specified and directed.

Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

300mm long aluminium alloy anodized sliding door (bolt type) and fixing clips of sheets, cast of extrusted sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy all as specified and directed.

150mm long aluminium alloy anodized sliding door (bolt type) and fixing clips of sheets, cast of extrusted sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

MS chromium plated tubular curtain rod fancy type of 25mm dia with and including fixing brackets, stops, corners & end cap etc fixed in repair complete all as spcified and directed.

GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste in repairs in patches n exc 5 sq. m each, including taking down old and jointing new to old as required.

Forming letters, figures etc. by cutting 'V grooves in new lime, cement-lime or cement plaster (per cm of height), complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described complete all as directed.

RCC (nominal mix) 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in slab supported on walls, columns in floors, roofs, landings, balconies and in shelves, complete all as specified and directed.

Mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified and directed.

Mild steel TMT bars 6-8mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces of concrete, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, finishing even & rough to receive wearing surface complete all as specified and directed.

Chequered cement concrete tiles 300x300x 25mm thick, set & jointed in neat cement slurry and pointed with equal proportion of white and grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete, brick work, masonry etc and making good disturbed ground, complete all as specified and directed. Notes : - This item shall also include the demolition of foundation concrete/hard core and taking out the posts and struts carefully and removing the same from site.

Excavation in post holes each not exceeding 0.5 cum getting out in any type of soil, returning, filling in, including spreading, leveling, watering and well ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, complete all as specified and directed.

Removing excavated material (earth) to a distance exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.50m above the starting point, all as specified and directed.

Mild steel work as in posts and struts in fencing including cuttings, tops to shapes, as directed, drilling, holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. fixed and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in post holes, complete all as specified and directed.

Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Supply only 4mm dia Chain link MS galvanised (zinc coating 60gram) fencing, any size or type, complete all as specified and directed. Note:-Type / size of fencing holes / dia of chain link fenching shall be as approved by GE. The weight of chain link fencing shall be calculated for payment as per actual weight or standard weight as per SSR which ever is less as approved by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified and directed.

Mild steel screw bolts 11-15mm dia at neck, machine made, with hexagonal or square heads at one end and screwed the other, or screwed both ends; each screwed and to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long, complete all as specified and directed.

Galvanised, 2 strand steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing and tying at crossings with and provision of galvanized mild steel wire, staple or steel pins, etc fixed in repairs complete all as specified and directed. Note;-Each line of wire shall be measured for record of measurement..

Vitreous china wash down water closet pan pedestal pattern in white colour with 'P' or 'S' traps excluding seat cover, flushing cistern and flush pipe fixed in repairs complete all as specified and directed. Cat Part No-20011 (SLICK) of Hindware or equivalent cat part of make specified in list make as approved by GE.

Vitreous china wash basin, white, flat back, size 550x400mm including CP mixer for mixing hot and cold water for pipe of bore 15mm, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets and waste pipe etc., fixed in repairs complete all as specified and directed. Cat Part No. 10036 of Hindware (Model-Windsor) or its equivalent in Neycer, Cera & Parryware.

PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets, fixed in repairs, complete all as specified and directed.

Dismantling PVC water tanks and removing to store of capacity exc 500 ltr but not exceeding 1000 ltr complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs including 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

Taking down existing water tubing and S&F Steel water tubing 15mm bore medium grade galvanized with all fittings like socket,union elbow ,tees short pieces, connectors, diminishing pieces, caps plug etc jointed and laid in trenches or fixed to wall, complete all as specified and directed.

Taking down existing water tubing and S&F Steel water tubing 20mm bore medium grade galvanized with all fittings like socket,union elbow ,tees short pieces, connectors, diminishing pieces, caps plug etc jointed and laid in trenches or fixed to wall, complete all as specified and directed.

20mm bore Stop valve cast copper alloy screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified and directed.

15mm bore Stop valve cast copper alloy screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified and directed.

15mm bore Stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified and directed.

Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and directed.

15mm bore Stop valve cast copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union fixed in repair, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm fixed, complete all as specified and directed.

Brass CP mixer 15mm bore dia of pipe for mixing hot or cold water, screwed for iron pipe and fixed in repairs, complete all as specified and directed.

Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth as in foundation etc. and getting out in any type of soil, complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete,complete all as specified and directed.

Form work to fair faces of walls, retaining walls, abudments, parapits and staircase railings and similar work including attached pillasters,buttresses etc vertical or to better with fair finished surface of concrete complete all as specified & directed.

RCC M-25(design mix) using (20mm graded crushed stone aggregate) as in wall, retaining wall, basement wall, blast walls and the like, any thickness above top of footings including attached pilasters and buttresses, complete all as specified and directed.

RCC M-25(design mix) using (20mm graded crushed stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed .

Removing excavated material (earth) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point, all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopper ends etccomplete all as specified and directed. (Note- Inner girth only measured.)

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint laid in trenches/floors, complete all as specified and directed.

PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate), for fixing of hold fast, copings, plinth bands bed blocks kerb or mud stops,rounded or chamfered angles and edges, including necessary form work complete all as specified and directed.

Aluminium door air tight of anodised frame made of size 100mmx45mm of section thickness 1.50mm thick with one or ore rebates including jointing cleats etc for fixing aluminium anodised door shutter fully panelled (two Nos of panels on each shutter) with 5.5mm thick tinted glass shutter rail made of 80mmx45mm of sheet thickness 1.50mm thick (Top, bottom, middle and side rail) single/double leaf side hinge type including necessary jointing /aluminium fillets/glazing bars with rubber gasket with aluminium fillets such as bottom door hydraulic door closer-01 No, aluminium tower bolt 150mm long 01No , aluminium anodised bow handles 300m 02 Nos fancy type on each shutter mortice locks 6 lever Make-harrison, one on each door, bottom and floor stoppers, all fitting shall be of ISI marked except cleats) sizes of each door shall be as per site requirement complete all as specified and directed.

Aluminium window air tight with glazing bar, with aluminium grills (oranmental type) window shutter style shall be 40mmx19mm, sheet thickness 1.5mm sliding channel 3mm thick of width as required and as directed by Engr-in-Charge of anodised frame made of size 75mmx40mm of section thickness 1.50mm thick, with or without rebate with toughned glass 5mm thick, including rubber beading and gasket and aluminium glazing clips, locking arrangement, aluminium anodised bow handles 75mm 01 No complete all as specified. Note :- All fitting shall be of ISI marked) sizes of each shutter shall be as per site requirement all as directed and specified.

Mild steel, plain, black sheet 1.00mm thick in wall cladding,steel gates/doors and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

Green Marble work 18mm to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) inclduing pointing in white cment (1:2) using marble dust with admixture of pigment to match with marble shade of Green marble with including 20mm thick screed bed/base layer in CM 1:4, complete all as specified and directed.

Cast iron pipes (spun pipe) with spigot and socket ends centrifugally cast in any length, laid in trenches or in floor of bore 100mm including lead joint fixed in repairs, complete all as specified and directed.

Cast iron pipes (spun pipe) with spigot and socket ends centrifugally cast. in any length, laid in trenches or in floor of bore 75mm including lead joint fixed in repairs complete all as specified and directed.

Cast iron pipes(spun pipe) with spigot and socket ends centrifugally cast. in any ength, fixed to wall of bore 75mm including lead joint fixed in repairs complete all as specified and directed

Cast iron pipes(spun pipe) with spigot and socket ends centrifugally cast. in any ength, fixed to wall of bore 50mm including lead joint fixed in repairs complete all as specified and directed

Cast iron bends (any redius) diminishing pieces or tapers (larger bore measured) for 100mm bore all as specified and directed.

Cast iron bends (any redius) with duck foot or heel rest for 100mm bore all as specified and directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches) for 100mm bore all as specified and directed.

Cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches) for 75mm bore all as specified and directed.

Cast iron cowl suitable for 50mm bore all as specified and directed.

Extra over only pipe fitting if fitted with oval access door for 100mm bore all as specified and directed.

Salt glazed stone water ware gully traps square moulthed type 'P' 150mmx150mm with excavation and earth work se in PCC M-10 (Nominal Mix) block measuring 45cmx45cm and cast iron grating incl jointing in cement mortar (1:1) fixed in repairs complete all as specified and directed

Concrete bed to drain pipes of 150mm dia including packing under and haunching against the sides of pipe after they are laid in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Plain cement concrete work in pavement/hard-standing of flexure strength 40 kg/per square centimeter in field using 400 kg of cement per cubic meter, thickness of concrete 25 cm or less including use and waste of necessary formwork all as specified and directed.

PCC 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in coping, benching, levelling course including rounded or chamfered angle as directed including necessary form work etc., complete all as specified and directed.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint for weep holes complete all as specified and directed.

Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in any type of soil, complete all as specified and directed.

Hard core filling under floor, of broken stone or boulder gauge exceeding 63mm and not exceeding 100mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rolled rammed to a true surface , complete all as specified and directed.

Plain cement concrete 1:5:10 type E-2 (using 20mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified and directed.

Brushing neat cemenr slurry with 3.0 kg of cement per sqm all as specified

18-20mm thick Machine cut Kota stone slab flooring, bedded and jointed with grey cement slurry and pointed with grey cement mixed with admixture or pigment to match the shade of Kota stone slab as approved by GE, laid over and including screed bed or bedding layer of mortar 20mm thick in Cement Mortar (1:4) including cutting, grinding and mirror polishing complete, all as specified and directed.

Mild steel work in tubular trusses, purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 including notching, drilling, fitting, riveting and or welding or connecting with bolts and nuts including rivets or nuts and bolts, providing and fixing cleats, fish plates, gusset plates etc also for wedging, plumbing, turning up & fixing complete all as specified and directed.

Construction of elevated sentry post with permanent specification complete all as specified and shown on drg GE/WD-02/23 Sheet 1/3, 2/3 & 3/3.

LLDPE conventional type septic tank designed to carry sewage and sludge water for 10 users incliding excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete all as specified and as directed. Make-Sintex, Rajshree, Polycon and Star

Soakage well of size 1.2 M dia X 3.0 M deep including excavation in any type of soil, foundation in PCC 1:3:6, wall of honey combed built in brick work in CM 1:4. and RCC cover M-25 concrete, filling with brick bats, complete all as specified & shown on Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

LLDPE conventional type septic tank designed to carry sewage and sludge water for 25 users incliding excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc., complete all as specified and as directed. Make-Sintex, Rajshree, Polycon and Star

Soakage well of size 1.8 M dia X 4.5 M deep including excavation in any type of soil, foundation in PCC 1:3:6, wall of honey combed built in brick work in CM 1:4. and RCC cover M-25 concrete, filling with brick bats, complete all as specified & shown on Drg No CE/TD-1202/03 sheet 1/2 & 2/2.

Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed.

Form work to sides of concrete foundations, footings, basis of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified and directed.

Reinforced concrete pipes150mm dia, class NP3, laid and jointed complete with collars all as specified and directed.

Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in reapir, complete all as specified and as directed.

Boom Barrier, boom length 06 Mtr (ISI Marked as approved by GE) High speed best quality, opening and closing time 6 second, electronic boom barriers, 90% duty cycle and very smooth movement, operated by radio receiver with remote control and push button including installation charges and photocell sensor complete all as specified & directed.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed.

Point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved colours and including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

One light point/fan /bell point controlled by one switch.

One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

One 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

Description all as per item No. 142 here-in-before but for 3 Pin socket outlet 16 Amps point on independent board controlled by other switches with 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables as main & neutral and 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables as earthwire complete all as specified and directed.

Modular type switch 6 Amps, single pole,1way,1 module, 240V, ISI Marked Complete all as specified and directed. “Cat part No ACVSXXWO61 of Crabtree (Havells) or its equivalent in Anchor, Legrand, Seimens as approved”.

Modular type switch 16 Amps, single pole,1way,1 module, 240V, ISI Marked Complete all as specified and directed. “Cat part No ACVSXXW161of Crabtree (Havells) or its equivalent in Anchor, Legrand, Seimens as approved”.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed. “Cat part No ACVKSWW063 of Crabtree (Havells) or its equivalent in Anchor, Legrand, Seimens as approved”.

Modular type socket 6 A/16 Amps, 6 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI Marked Complete all as specified and directed . “Cat part No ACVKCWW163 of Crabtree (Havells) or its equivalent in Anchor, Legrand, Seimens as approved”.

Fan regulator modular type electronic compatible with BLDC fan, stepped type 100 Watts, 2 module 240Volts, AC ISI marked complete all as specified and directed. “Cat part No ACVRFHW008 of Crabtree (Havells) or its equivalent cat part of make Anchor, Legrand, Seimens as approved by GE”.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Energy saving LED lamps 13 watt, 230 volts, 50 HZ ,base holder B22 type, complete all as specified and directed. Make-Havells Cat Part No- LHLDDDBEBI2R007 or equivalent of Make-Phillips, Crompton, wipro, bajaj as approved.

LED light fitting 1x10W bulk head luminaries IP 65 complete with all accessories including LED lamp 10 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed. Cat part No RUGBYGENXFTS10WLED865SSYMBOPC Make Havells or Bajaj/Philips/Crompton Greaves or its equivalent)..

Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed.

LED light luminaire 600mm x 600mm 35/36 watt, 220 AV recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, Holder & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete incl testing after fixing all as specified and directed.

LED light fitting 1x20W, 220V, AC decorative box type with driver, Holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delivery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES all as specified and directed. Cat Part No Zinger of Havells or its equivalent in Orient, Bajaj, Crompton as approved.

Taking down old unserviceable Exhaust fan of any type/size from existing location and depositing the same in MES store yard and Supply and fix Exhaust fan single phase metal body, AC 230 Volt, 50 Hz of size 300mm sweep with louvers shutters complete with all accessories including connecting up from ceiling rose to motor all as specified and directed. "Cat part No refresh air SPS of Havells standard or its equivalent, Bajaj, Orient, Crompton as approved".

Electric water heater storage type, capacity 25 litres and heating element 2KW, BEE 5 Star rated complete with all accessories such as a safety valve, thermostate, NRV, connection pipes of GI/PVC and necessary electric connections etc including taking down existing and depositing in MES. Make : Crompton/Havells/Bajaj as approved.

Sheet metal enclosure double door type for DBs single pole and neutral 12 way 240 V with 200 Amp bus bar including blanking plates where required including fixed flush in wall chases wall for fixing DB and making good surfaces to match with existing surface in repairs all as specified and directed. “Cat part No DHDMSHODDW12 of Havells, or is equivalent in Siemens, L&T, Legrand as approved."

MCB TPN 415 Volts 16 KA, 63 Amp suitable for TPN vertical loadline including taking down existing one. Make : Indoasian, Legrand, Schiender, Havells etc.

Sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade,FRLS type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLS type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface including cutting and cheasing including taking down existing and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

MCB single pole and neutral 63 amps 240 volts 10 KA 'C' series, complete all as specified and directed. Make:- Make:-Havells cat part No-DHMGCSNF063 or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE

MCB single pole & neutral 6 to 32 amps 240 volts 10 KA 'C' series fixed in repair, complete all as specified and directed. Make:-Havells cat part No-DHMGCSNF006-032 or its equivalent cat part of make-Legrand / ABB / L&T as approved by GE

Supply, laying & testing of XLPE insulated, armoured, heavy duty electric under ground cable with stranded aluminium conductor of size 25 Sqmm nominal cross section x 4 core., 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs, including taking down old unsv cable, complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45cm x 45cm x 45 cm,RCC cover 1:2:4 type B1 of size 45x45x6 cm, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed.Note:- The required resistance of Earthing shall be less than 3 ohm, If not found to the required resisstance, the contractor has to re earthing for required resistance and the cost for the same included in the quoted rate and no extra shall be paid on failure of getting required resistance.

Sand cushioning to under ground cable, 8 cms thick before laying the cable and 15 cms thick after laying and stretching the cable in trenches including hand punning and consolidating, punned to 18cm thickness, complete all as specified and directed. Note : For payment purpose, only punned thickness shall be measured.

Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat, complete all as specified and directed.

M/s Mool Raj Ramesh Chander