SPL REPAIR TO BLDG NO PV17 P53 AT NEW MIL STN UNDER GE GANGTOK

Amount

Dismantling old PGI/CGI sheeting of any gauge thickness, including Nainital. Sikkim or similar pattern roof/facia etc complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls incl raking out joints hacking for key, scrubing down with water etc. complete all as specified and as directed.

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of dismantled materials/rubbish from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm nut n.exc 4Sqm all as specified and as directed.

M&L for 75mm thick PCC type C2 (1:3:6) (using 40mm graded crushed stone agg) as in plinth protection/Path/hardstanding finished the concrete surfaces even and smooth without using extra cement etc complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor complete all as specified and as directed.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed by the Engr-in-Charge.

S&F for 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and directed.

M&L for pre cast cement concrete block masonry with solid blocks, exc. 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded crushed stone aggregate) as per IS 383 complete all as specified and as directed.

M & L for 20mm thick rendering in cement plaster in CM (1:4) in two layer and top layer 10mm thick shall be mixed with WPC @ 3% by weight of cement on fair faces of stone masonry wall incl finish the surface even and fair without using extra cement complete all as directed and specified (WPC shall be measured and paid separatly)

Supply only Integral waterproofing compound .

M&L for 15 mm thick rendering plaster on fair faces of conc faces/ brick wall faces of smooth without extra cement in CM (1:6) complete all as specified and as directed .

M&L for for applying two coat of exterior acrylic emulsion weather proof paint overa coat of primer on new /old plasterd surface including preparation of new/old plasterd surface etc complete all as specified and directed.

All as per items No 18.00 but one coat of exterior acrylic emulsion painting on old wall surfaces completed all as specified and directed.

M&L for preparation of new plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall suface on a coat wall care putty complete all as specified and directed.

M&L for preparation of coplete removal of existing treatement on old plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over old wall surface on a coat of 2mm thick wall care putty,complete all as specified and directed.

S&F 5 to 6mm thick PVC wall/ceiling panels of interlocking types, width 250/255 mm with lamination design and exc 60% of PVC content including necessary H-joints, internal/external corner trim, coner cove,F/J edge trims where required fixed with hidden screws to steel/wooden frame work complete all as specified and as directed.

All as per item No 23.00 above but openable/fix type window/ventilator complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed.

S&F in repairs Aluminium body Door closer hydraulically regulated,designation No. 3,universal type, suitable for door shutters of 851to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for door shutters complete all as speciofied and directed.

M & L for 2nd class hard wood timber scantling of any size or in any position such as truss,purlin etc and if in repairs, to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions to store

S & F in repair Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified & as directed incl taking down old scrap iron grill.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats synthetic enamal paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old or previously treated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamal paint over old steel surface complete all as specified and directed.

S&F as in repair stain less steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified

M&L preparation of old or previously treated wooden surfaces of any description over 10 cm width or grith and applying one coat of synthetic enamel paint over wooden surface complete.

S&F and in repair 2nd class hard wood Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps with nails etc complete all as spd and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in surface channels/drain including forming fair finished to drain channel.

Roughening surfaces of old concrete floor or wall surface by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

Material and labour for hardcore of gauge n.exc.63mm (using broken stone or boulders) deposited, spread and levelled in layers not exc.15cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed.

M & L for Plain Cement concrete 100mm thick type B- 2, (1:2:4) (using 40mm graded crushed stone aggregate) as in hard stand /path etc including finish the surface even and fair without using extra cement etc complete all as specified and directed.

M&L for lacquer coated precast chequered cement concrete tiles floor of size 200x200x25mm/300x300x25mm thick set and jointed in grey cement pigment to match over 15mm thick scteed in CM (1:6) complete all as specified and directed

Excavation in trenches inot exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out as in soft/loose soil for foundation etc complete all as directed.

M&L for PCC (1:3:6) type C2 (40 mm graded crushed stone aggregate ) as in foundation and mass concrete complete all as directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement moratar (1:6) complete all as directed.

M&L for PCC (1:3:6) type C1 (20 mm graded crushed stone aggregate ) as in coping, bed plates ,parepet,plinth course including weathering, slightly rounded or chamfered angles and throating, all as specified and as directed.

Returning, filling in soil/ Back filling of retaining walls using approved earth obtained from excavation incl watering, well ramming, etc complete all as directed.

Removing excavated soil to a dist n.exc.50m complete all as specified and as directed.

S&F Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer in CM(1:6) all as spd and directed.

All as per item No 48.00 above but on vertical surface of wall like skerting/dadoi etc on 15mm thick rendering complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7mm to 8 mm thick(square/rectangular) area of each tile exceeding 0.11Sqm, but not exceeding 0.36 Sqm , in floors over and including 15mm thick screed in CM (1:6) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as spfd & directed.

M&L for glazed coloured ( 350 x 450 mm/250 x 350mm) x 7 mm th as in skirting/dado over & including 10 mm th rendering in CM 1:4 set & jointed in neat cement sullry & pointed in white or coloured cement to match complete all as specified and as directed.

M & L for Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed in CM (1:6) etc complete all as specified and as directed.

M&L for RCC type B1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, cover slab, balconies, canopies, deck slabs and in shelves and the like complete all as specified & as directed.NOTE : Re-inforcement shall be measured and paid separately.

M&L mild steel bars 10 mm dia & over cut to length bent to shape required, including cracking, bending spirally to proper for columns, hooking end & binding with and inch mild steel wire not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as spfd and directed

M&L for MS bars 5 mm dia and over upto and including 10 mm dia in stirrups cut to length, bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire(annealed) not less than 0.9mm dia quality conforming to TMT bars complete all as specified and directed.

M & L for Formwork to sides and soffits of columns or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

M & L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick etc complete all as specified and as directed.

S&F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw as in cup boards ,shelves etc all as diercted by Engr In Charge.

S&F in repairs PVC (SWR) half round 150mm dia with round edges iuncl all accessories like bend,T etc complete all as specified and as directed

S&F 110mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls or fixed to steel gutter complete all as directed.

Supply and fix 110 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and as directed.

S&F 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed on walls with necessary clamps etc complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls complete all as specified and as directed.

Supply & fix in repair 110 mm bore PVC (SWR) vent cowl fixed in position complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as specified and as directed.

S&F 150mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.

Supply and fix 150 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls or fixed to steel gutter complete all as specified and as directed.

Taking down 15mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

Taking down 20mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

S&F galvanised steel water tubing 15 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed by the Engr-in-Charge.

S&F galvanised steel water tubing 20 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed by the Engr-in-Charge.

Refixing of old 15mm bore steel tubing and connections in new or old position (wall, ceiling or floor, etc) complete all as specified and as directed.

S&F in repair, 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed.

S&F white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 520 x 360 x 390 mm with ‘P’ or `S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminium anodised hinging device, making all necessary connections and making good the disturbed surfaces of floor complete all as specified and as directed.

S&F in repairs vitreous china, white colour, flat back, wash hand basin of size 55 x 40 x 79cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling and making all necessary connections complete all as specified and as directed.

S&F cromium plated central hole basin mixer Extended casted spout with 450mm long braided hoses complete all as specified and as directed.

S&F and in repair cromium plated wall mixer 15mm bore with 115mm long bend pipe for connection to over head shower (with Bush & piston diverter fittings) with aerator screwed down for 15mm bore GI Pipe or for brass ferrule complete all as specified and directed.

S&F in repair Bib tap , long body cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one complete all as specified and as directed.

S&F in repair two way Bib tap , long body cast copper alloy, chromium plated with crutch or butterfly handle with healthfuceset , screwed down for 15mm bore GI Pipe or for brass ferrule complete all as specified and as directed.

S&F in repair corner glass shelf 225x 225mm with CP steel frame complete all as specified and directed complete all as specified and as directed.

S&F in repair Angular Stop Cock with flang complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S &F CP tubular towel rail 20mm dia D tupe 60cm long complete all as specified and as directed.

Supply & fix in repair 75 mm dia PVC floor trap of outlet, with gratings, including jointing to waste pipe fixed in PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

S&F Rolled section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleat or other connecting plates confirming to Fe-410-W (Gde-E-250) complete all as specified and as directed.

S&F decorative type curtain rod ,chromium plated 25mm dia with fixing btackets ,stops and complete fittings including making good the surface were damaged complete all as specified and as directed.by Engr In charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F powder coated GI grid frame work for false ceiling comprising of the following sections for making partition of 600x600mm size fixed to walls with rawl plugs and screws and hanged to roof with and including 1.18 mm dia GI wire suspender of suitable length and buterfly clips, size of main tee shall be 23mmx 28mmx 0.30mm thick, cross tee shall be 24 x 23 x 0.30 mm thick and wall angle shall be 20mmx20mmx0.30mm thick complete all as specified and directed.

S&F for 4mm thick Non asbestos fibre cement building board (E-board) of approved texture for insulation and acoustic purpose of size 595x595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surface and applying one coats of oil emulsion distemper over a coat of primer including preparation of surfaces complete all as specified and directed.

All as per item No 92.00 here-in-above but openable/fix type window/ventilator complete all as specified and directed.

Taking down 25mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as specified and as directed.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified etc complete all as directed by the Engr-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S&F MS but hinges 75mm long complete all as specified and as directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section100mm long complete all as specified and as directed.

S&F 150mm long Aluminium handles, cast type, anodised complete all as specified and as directed.

S&F galvanised steel water tubing 25 mm bore, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as specified and as directed by the Engr-in-Charge.

M&L framed work such as grills, gratings, gate etc with ends of bars & plates souldered and/or riveted or forged into spikes, framed guard bars barred iron dors ladders framed balusters walkways, railing frame work of water tanks, portion framed and hung as gates including pintle hinges, stops hand-made sliding bolts and similar work conforming to Fe-290-0 or E-165, complete all as specified and directed.

S&F in repairs CP Toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in repairs soap dish cromium plated body and Polycarbonate brackets including wall flange and screws etc complete all as specified and as directed.

S&F in repairs stainless steel plate rack of 1mm thick and size 910x1000mmx250mm three tier complete all as specified and as directed.

S&F in repairs stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs stainless steel cloth hanger 300x50x32 mm complete all as specified and as directed.

M&L for Drilling holes in granite or trap stone for bolts, pipes, etc. n. exc 25mm dia complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

S&F in repairs Harrison rails, mild steel, chromium plated 25mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed.

E/M Portion: Taking down carefully copper/ aluminium point wiring for light, fan, socket or power point complete with fittings such as switches, fan regulators, light fittings, tube light fittings, bracket light fittings and ceilling rose, holders and including making good the disturbed surface on walls, complete all as specified and as directed.

M&L point wiring complete with 1.5 Sqm sincle core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) one light point controlled by one, one way switch, with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI) marked concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3mm thick bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc complete all as specified and as directed.

All as per srl item No 112.00 here-in-above but one 3 pin 5 amps switch socket outlet point on independent board complete all as specified and as directed.

All as per srl item No 112.00 here-in-above but one One bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and as directed.

All as per srl item No 112.00 here-in-above but wiring with 2.5 sq.mm multistranded cable and earth wire with copper conductor 2.5 Sqmm complete all as specified and as directed.

S&F modular switch 1 way 6 Amp, 1 module 230 volts, 50Hz, (ISI marked) complete all as specified and as directed.

S&F socket, 6A, 2/3 pin combined 2 module 230 volts, 50Hz, (ISI marked) complete all as specified and as directed.

S&F modular bell push 6A, 1 module 230 volts, 50Hz (ISI marked) complete all as specified and as directed.

S&F modular switch 1 way 16 Amp, 1 module 230 volts, 50Hz, (ISI marked) complete all as specified and as directed.

S&F socket, 6Amp/16Amp, 2/3 pin combined 2 module 230 volts, 50Hz, (ISI marked) complete all as specified and as directed.

M & L for point wiring with PVC insulated unsheathed multi stranded copper conductor cable, 1100 volt, FRLSH grade of size 1.5Sqmm drawn through and including surface PVC casing & caping (ISI Marked) with accessories including PVC Box or existing sunken box and hylem sheet/PVC Box including 1.5 sqmm copper conductor cable for earth continuty green in colour for one light point/fan point/Bell point controlled by one 5/6 Amps one way switch complete all as specified and as directed by Engr-in-charge. Note:-(i) All the disturbed surfaces of wall / ceiling shall be made good to match the existing wall / ceiling finishes and as directed by the Engineer-in-Charge.

All as per item No 121.00 here-in-above but, one socket outlet, three pin, 5/6 Amp on the same board with other switches complete all as specified and as directed.

Description all as per item No. 122.00 here-in-above but for 15/16Amp switch socket out let, independent with 2.5 sqmm copper cable of PVC insulated, unsheathed, multi stranded and 2.5 Sqmm for earth continuity conductor, complete all as specified and as directed.

Supply and fix switch socket combination 2 pin & 3 pin 5 Amp, 230 volt flush, multipurpose, flush, non shutter, non inter locking type, white/ivory finish with 2 screw fixing hole including suitable gang box fix on wall complete all as specified and as directed.

Supply and fix switch socket combination 5 in 1 type, 3 pin 5 / 16Amp, 230 volt, complete all as specified and as directed.

Supply and fixing of switch paino, flush type, single pole, one way, 5/6 Amp, (ISI marked) complete all as specified & as directed.

S&F in replacement of 1 x 18 W LED tubelight fitting with lamp, extruded aluminium, PC diffuser, efficiency > 125 lm/W, glare free, THD<10%, potted electronic driver connecting up with three core flexiable copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make:- Crompton Cat part No - CCS-100-20-65-HLL-OP-NWH/ Havells Cat part No ENDURALINEARPROBS20WLED 865SPCSSIND/ Philips cat part No BN170C LED20S-6500 PSU L120

Supply and fix LED wall light 1x20w 220 V AC holder with LED bulb suitable for 20 W LED retrofit lamp B22 base with connecting up with three core flexible copper conductor complete all as specified and as directed.

Supply & fixing LED lights fitting 1x9 /1x10 W 220 V, AC bulk head luminaries including , holder including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fixing LED Mirror lights light fitting with high out put diffuser 2 feet , 10 watt 220 v AC decorative type with driver holder and LED lamp including connecting up with driver three core flexible copper conductor cases suitable size complete all as specified and as directed.

S&F LED ceiling lights 15W pearl plus down light 220 v AC connecting up with driver two core flexible copper conductor cases suitable size complete all as specified and as directed.

S&F ceiling rose, 3 phase ,PVC polycarbonate ,insulated body (ISI Marked) complete all as specified and directed.

Supply & fix lamp holder angular/straight insulated body, with back plate suitable for batten fittings, white/ivory finish complete all as specified and as directed

Supply and fixing buzzer Ding Dong type, AC 230 volts single pole with suitable fixing arrangement complete all as specified and as directed.

Supply and fix exhaust fan, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V ,50 Hz RPM 1200 , copper winding of sweep 250mm sweep with making connections with 3 core flexible multistranded copper conductor of size 0.75 sqmm run through flexible pipe including cutting holes and making good the disturbed surfaces of walls in CM (1:4) and finishing the surface as per existing colour scheme complete all as specified and as directed.

Supply and fix of exhaust Fan, 300mm sweep MS body with anti dust painting 4 blade with heavy duty motor and double ball bearing 1320 RPM single phase 230/240 volts copper wounds, Air delivery-1600 CMH complete with all accessories as Bird guard/louvers shutters etc 3 core flexible multistranded copper conductor of size 0.75 sqmm run through flexible pipe including cutting holes and making good the disturbed surfaces of walls in CM (1:4) and finishing the surface as per existing colour scheme complete all as specified and as directed.

S&F singel pole & neutral enclosure with a two pin & earth plug & socket complete with one single pole MCB C curve of 20A rating complete all as specified and as directed.

M&L for concealed sub-main wiring along with earth wire of size e 2x10 sqmm with 1x6 sqmm earth wire ,ISI marked FRLS ,PVC insulated ,multi stranded , copper conductor ,single core cable drawn through and incl PVC rigid conduit (medium grade) size not less than 25 mm with all fittings and accessories (ISI marked) including cutting chases for conduit & sinking for sunken boxes & making good to walls, floors etc complete all as specified and as directed

M&L for concealed sub-main wiring along with earth wire of size 2x06 sqmm with 1x4 sqmm earth wire ,ISI marked FRLS ,PVC insulated ,multi stranded , copper conductor ,single core cable drawn through and incl PVC rigid conduit (medium grade) size not less than 25 mm with all fittings and accessories (ISI marked) including cutting chases for conduit & sinking for sunken boxes & making good to walls, floors etc complete all as specified and as directed

S&F for MCB DB SPN 8 ways Double Door 240 Volt with 200 Amp rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed

S&F for MCB DB SPN 12 ways Double Door 240 Volt with 200 Amp rated bus bar ,IP-42,IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall / other surface complete all as specified and as directed

S&F MCB single pole & neutral SPN 32 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed

S&F MCB single pole 6 to 32 Amps , 240 Volts , 10 KA rupturing capacity , C curve complete all as specified and as directed

Taking down and refixing of Geysers storage type after complition of civil works 25/50 ltrs capacity complete with grounding/drilling in wall and provn of Zinc coated fastner 12mm dia 150mm long x 04 Nos including replace hot & cold PVC pipe complete including nuts/bolt, painting and testing complete all as specified and as directed.

Supply ,laying ,jointing and testing in trenches or passing through pipe, 1100 Volts grade XLPE insulated, armoured heavy duty electric cable with aluminium conductor of cross sectional area 6 Sqmm 2 core with necessary fixing arrangements such as lugs, glands and terminal etc complete all as specified and as directed

Supply and fixing LED building light fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65 /66 protection and impact resistance of IK07 complete GI bracket 1.5m long made out of GI dia suitable for fixing street lights bend to suitable radius incl 2 sets of clamps nuts bolts washers incl painting with aluminium paint etc complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level connected with galvanised iron/steel earth wire of 4 mm dia by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I and earth wire protected by galvanized pipe light grade 15mm bore and connected to DBs including necessary earthwork and excavation in any type of soil, GI light grade 20mm bore watering pipe with funnel and wire mesh, PCC (1:2:4) type B1 chamber with 40mm thick RCC (1:2:4) type B1 design mix cover slab with 6mm dia MS bars at 100mm c/c both ways with MS Hook 6mm dia MS bars etc complete all as specified and directed by Engineer-in-Charge including testing on completion.

DHARMINDER SINGH (BID ID -3305774)

M/S S. S CHETTRI AND SONS (BID ID -3307621)

M/S ANIL KUMAR THAKUR (BID ID -3304835)

MAHENDRA KHAWAS (BID ID -3308918)

KAMLESH ENTERPRISE (BID ID -3308257)

SANJAY MITTAL (BID ID -3306517)

SANJAY KAUSHIK (BID ID -3306081)

KARMA TSETEN BHUTIA (BID ID -3307396)

RAAJ BANGAR (BID ID -3306089)

GEETA CONSTRUCTION (BID ID -3306156)