PROVN OF SHED FOR HEAVY MACHINERY OF 508 ABW AT CHHEOKI

Amount

Surface dressing n.exc 15cm deep in soft/loose soil complete all as specified and directed

Excavting in trenches, n.exc 1.5m wide and n.exc 1.5m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc., n.exc 10sqm on plan and n.exc 1.5m in depth and gtting in hard/dense soil complete all as specified and directed

Excavation over area n.exc 1.5mtr deep and getting out in soft/loose soil all as specified and directed

Form work to sites of concrete foundation, footing, bases of column, rfts and rafts beams, sites and sofits of foundation and plinth beam and similar work rough finished surface complete all as specified and directed

M&L for RCC M-25 design mix using 20mm graded stone agg for as in foundation, including rafts, footings, foundation beams, plinth beam, bases of column and basements, under reamed pilies and mass concrete complete all as specified and directed

M&L for RCC M-25 as in slab supported on walls, beams, coln in floors, roofs, landing balconies deck slab and in shelves and the like complete all as specified and directed.

All as per Ser item No 6 here-in-above but in column, pillars, piers, post and struts complete all as specified and directed.

M&L for 20mm thick waterproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metalic hardner) complete all as specified and directed.

Supply only metallic floor hardner complete all as specified and directed

M&L for 15mm thick rendering on other than fair faces of brick work in CM 1:6 finished even and smoom without using extra cement complete all as specified and directed

M&L for preparation of new plaster surface in and applying three coat of white wash complete all as specified and directed.

M&L for Treating the bottom and sides of excavation at the rate of 5 liters of emulsion per square meter of surface area complete all as specified and directed

M&L for treating the backfill in contact with foundation at the rate of 7.5 ltrs of emulsion per sqm of vertical surface (Area of the sub structure in contact with backfill to be measured). complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed

M&L for pressed steel frames for doors of size 125mm 60mm with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified and directed

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

Use and waste of Formwork to sides of pillars, posts, struts, piers, columns, and stanchions for rectangular , square or polygun fair finished surfaces of concrete complete all as specified and directed

M&L for RCC M-25 design mix using 20mm graded stone aggregate for columns, pillars, piers, posts and struts complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm as in hard/dense soil complete all as specified and directed

Removing excavated material (soil) to a deistance n.exc 50 m and deposited where directed at a level n.exc 1.5m above the starting point complete all as specified and directed

M&L for Hard core of gauge not exc 63 mm deposited,spread and levelled in layers not exc 15 cm thick watered rammed to a true surface with broken stone / boulders complete all as specified and directed

M&L for sand filling under floors or in fdn incl watering and consolidation complete all as specified and directed

M&L PCC 1:4:8 type D2, using (40 mm graded agg) ,150 mm thick as in sub base of flooring all as specified & directed

M&L PCC 1:2:4 type B1, using (20 mm graded agg) ,100 mm thick as in floors & pavings laid in alternate panels all as specified & directed

M&L for forming construction joint 30mm deep 10mm wide filled with sealing compond Gde-A complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length , bent to shape required including cranking bending etc and binding with mild steel wire (annealed ) not less than 0.90 mm dia as in reinforcement complete all as specified and directed.

All as per Ser item No 26 here-in-above but 5mm dia and over up to and incl 10mm dia in stirrups, spacer and binder complete all as specified and directed

S&F for Plates (plain or chequered) channels, square cut or notched (ordinary & counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde. E-250) quality 'A' all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to Fe 410-W (Gde-E-250 quality A) complete all as specified and as directed by the Engineer-in-Charge

M&L for plate girder or single stanchions, built up of one beam of channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections Fe 410-W(Gde E-250) quality - 'A' complete all as specified and directed.

S & F of Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 22.5cm long,16mm to 20mm dia complete all as specified & directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tenstile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of an colour having tenstile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed

S&F M S flat iron wind ties for roof including securing bolts & & all necessary drilling ,bolting or riveting etc and similar work conforming to FE-290 Gde E-165 complete all as specified and directed.

M&L for preparation of steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6. complete all as specified and directed

M&L for 15mm thick rendering on fair faces of brick work in CM 1:4 finished even and smooth with out using extra cement complete all as specified and directed.

M&L for cement concrete 1:2:4 type B0 (12.5mm graded aggregate) as lintel, cills, steps sesmic and other similar bends coping and similar items etc.complete all as specified and directed

S&F MS rolled section as in framing for clading,glazing and like fix with and connecting plates etc. (Fe-410-w Gde-E quality-A) complete all as specified and directed

S&F framed work in doors or gates of angle or other section with gusset plates, rails braces etc, of grade Fe 410-0 or Fe-10-0 cpmplete drill for fixing of steel sheeting or other covering . Doors etc to be prepared by hanging and sliding with and including either hooks and hinges por steel hanging door fittings (exclusive of steel sheeting or other covering , running, rails & guide) and hanging also fastening and fixing complete all as specified and directed.

M & L PCC 1:3:6, type C2 (using 40 mm graded agg) 75 mm thick as in plinth protection without using extra cement complete all as specified and directed.

S&F 1.2mm thick MS sheet in wall clading, steel gates and similar work, cut to size,holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.`complete all as specified and directed

M&L for preparation of new plastered surface of any description applying two coats of cement base paint over a coat of primer on surfaces of wall complete all as spd and directed

S&F 125mm dia CI roller with 40mm thick CI bush assembly all as specified and directed

S&F rail 50R complete all as specified and directed.

S&F 150mm dia 50mm thick CI wheel complete all as specified and directed.

S&F welded steel wire fabric n.exc 4 Kg complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft losse soil

M & L for Soling (or sub base) of well broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated to requied gradient and camber complete all as specified and as directed by the Engineer-in-Charge.

M & L for PCC 1:5:10 Type E2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L cement concrete work in pavement/hard standing of flexural strength 40 kg/per square centimeter in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all as specified and as directed by the Engineer-in-Charge.

M&L for forming 12mm thick expansion joints fied with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade-A. complete all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring (Steel Conduit type) complete with FRLS PVC insulated, unsheathed stranded copper conductor of nominal area 1.5 Sqmm( 22/0.30 or 30/0.25), 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly in and including cutting/chasing on brick wall not exc. 10 cm girth (excluding ceiling surface) and supply and fixing PVC conduit pipe medium grade of nominal size 20 mm dia along with connected fittings/junction boxes using new MS sunk terminal boxes of thickness not less 1.22 mm, new 3 mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good complete all as specified and directed and suitable for the following: -

(i) One light point or one fan point controlled by one, 1- way switch

(ii) One 3/5 pin socket outlet, 6 Amp on “independent board”

(iii) One 3/5 pin socket outlet, 6 Amp on the same board with other switches

All as per Ser item No. 53 here in before but point wiring using 2.5 sq mm suitable for 16 amps “ independent board”.

Supply & fixing ISI marked switch piano flush button type, single pole, one way, 6 Amps, 240 volts for point wiring complete all as specified and directed .

Supply & fixing socket out let 6 pin, 6 Amps flush type for point wiring complete all as specified and directed . .

Supply & Fixing switch socket combination multipurpose 2 in 1, 6 pin, 6 and 16 Amp, and flush type universal for power point wiring complete all as specified and directed .

Supply & fixing ceiling rose 3 pin/PVC/ polycarbonate, isolated body with colour ring for fan point wiring all as specified and directed .

Supply and fixing Exhaust fan , steel body AC single phase 230 V of size 450mm sweep with , blade and frames and lovers with making hole, ISI marked complete all as specified and directed.

Supply & fixing industrial wall mounted plug socket of 32 amps three phase one neutral and earthing suitable for IP 67 complete all as specified and directed .

Supply, fixing, connecting & testing T8 TLED with suspended mounted waterproof luminiare suitable for twin LED tube light of 19 Watt having IP 65 protection with complete suspension system complete all as specified and directed. Make: TCW450 P 2XTLED 19W P3397 of Philips/Havells/CG or as approved

Supply and fixing 1100 volts grade heavy duty cable PVC insulated copper conductor for submain wiring alongwith earth wire with 4x10 sqmm+2x6 sqmm earth wire sizes of FRLS is pvc insulated copper conductor , single core cable insurface /recessed as required complete all as specified and directed.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated copper conductor for submain wiring alongwith earth wire with 4x16sqmm+2x10 sqmm earth wire sizes of FRLS is pvc insulated copper conductor , single core cable insurface /recessed as required complete all as specified and directed.

Supply & fixing TPN MCB Distribution Box of 12 Way, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar confirming to IS 13032 & 8623 complete all as specified and directed. Cat Part no - DHDPSHODPW04 of make - Havells or its equivalent model in Standard/Schneider Electric/L&T/ HPL/ Indo asian/Hager

Supply & fixing DB with single phase & neutral MCB Distribution Box of 8 Way, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar confirming to IS 13032 & 8623 complete all as specified and directed. Cat Part no - DHDPSHODPW04 of make - Havells or its equivalent model in Standard/Schneider Electric/L&T/ HPL/ Indo asian/Hager

Supply & fixing MCB with MCB SP, 06 to 32 Amps 240 volts AC , 'C' Series, conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply & fixing MCB with MCB SPN, 63 Amps 240 volts AC , 'C' Series, conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply & fixing MCB with MCB TPN,100 Amps 440 volts AC , 'C' Series, conforming to IS 8828/IEC 60898-1 including making connections with copper lugs, testing as required complete all as specified and directed.

Supply & fixing Air Circulator fans 230 volts single phase oscillating 450mm sweep suitable for wall mounting complete all as specified and directed.

M&L for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.5 metres deep below ground level) with top edge of the plate not less than 1.25 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe medium grade 40 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade compete all as specified as shown in electrical plate no. 2 of SSR Part-I and testing of earth resistance as required.

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth for laying of pipe, and getting out in soft/loose soil All as specified and directed

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 Cms in soft/loose soil All as specified and directed

Supply and Fixing and testing of galvanized steel tubing of following sizes, medium grade with all fittings and fixed to walls and ceilings or laid in floors,trenches complete all as specified and directed.

(b) 20mm bore

(c) 25mm bore

(d) 40 mm bore

S&F and testing in replacement stop valves, cast iron, screwed down, high pressure, with crutch or butterfly handle, screwed both ends, for iron pipe or for unions of following sizes, complete all as specified and directed.

(b) 20mm bore

(c) 25mm bore

S & F in replacement Gun Metal Globe or gate valve with iron wheel head , screwed both ends for iron pipe or for unions of following sizes, complete all as specified and directed.

(a) 40 mm bore

MOHAMMAD RIZWAN CONTRACTOR

PERFECT ENTERPRIOSES

YASH ENTERPRISES

M/S VIVEK DUBEY

M/s VIJAY TRADERS

Raghvendra Enterprises

M/S PRAGATEE ENTERPRISES

Channa Brothers and Co.

SUNIL ENTERPRISES