REPAIR REPLACEMENT OF CERTAIN B/R ITEMS AND INTERNAL ELECTRIFICATION WORKS IN CETRAIN BLDGS OF AGE BR- I UNDER GE SAUGOR

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water and removal of debris out of MD land complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all qoins arches , pillars etc built in cement mortar and removal of debris out of MD land complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straright or corved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item No 03 as above but except bricks Note:- Serviceable bricks obtained from Srl item No.2 above shall be re-used in this item

M&L for rendering 15mm thick cement plaster on wall in cement mortar 1:6 on brick wall / concrete surfaces of finishing the surfaces even and smooth complete all as specified and directed.

M&L for rendering 10mm thick on other than fair face of brickwork or concrete surfaces in cement mortar 1:4 complete all as specified

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed.

M&L for applying three coats of white wash on new plastered surface of ceiling including preparation of surface complete all as specified and directed.

M&L for preparing the new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces on wall and applying two coats of oil emulsion distemper over a coat of wall primer complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm below or above ground floor and removal of debris out of MD land complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding and rubbish off the premises complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-1 (using 20 mm graged stone aggregates) as in floors finished rough to receive the tiles or kota stone complete all as specified & directed..

M&L for non-skid coloured ceremic tiles (Endura) 7 to 8 mm thick (Square/ rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

All as per Srl item No. 14 above but as in dado / skirting etc over and including 10mm thick rendering in CM 1:4

M&L for coloured glazed ceramic tiles premium quality of size 600mm x 300mm x 7mm thick, joint free (rectified)) coloured, on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white/ coloured cement to match the colour of tiles laid over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed. .

M&L for coloured glazed ceramic tiles premium quality of size 450mm x 300mm x7mm to 8mm thick, coloured, on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white/ coloured cement to match the colour of tiles laid over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 600mm x 600mm x 8mm to 10 mm thick coloured premium quality vitrified tiles in floors set & jointed in neat cement slurry and pointed in white /coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

All as per item No. 18 above but in dado / skirting etc over and including 10mm thick rendering in CM 1:4

M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment laid over and including 40mm thick uniformly levelled surface of stone dust cushioning complete all as specified and directed.

M&L for 20 mm thick black granite stone slab with table rubbed and polished fixed horizontial or vertical set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite slab complete all as specified and directed.

Dismantling false ceiling of any description or in any thickness, including cover fillets complete all as directed by Engr-in-Charge.

M&L for 600x600x7mm thick vinyl face, cinyl covered edges and washable metallized polyster foil backing, weight @ 5.6Kg/m2 suspended false ceilling comprising of non asbestos fibre cement bulding boards fixed or laid/inserted to GI frame work with screws over GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to sourrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to centre including hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long complete all as specified. Make : ArmGyp-FB Ceilings (Armstrong) Model : Sleet (Alpha Lite)

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridge etc complete all as specified and directed.

S&F pre- coated galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ150) as in roof covering/ clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre- coated galvalume aluminum zinc coating GI based profile ridge steel sheet of 0.50 mm thick of any colour having tensile strength of 550 mpa (AZ150) as in ridges, roof covering/ clading to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs Fixed with L-type or J-type or cranked hook bolts complete all as specified and directed

All as per Srl item No. 27 above but except sheets - ditto - Note:- Serviceable AC sheets obtained from Srl item No.24 above shall be re-used in this item.

S&F in repair 2mm thick fibre glass reinforced traslucent corrugated sheeting with two corrugation side lap fixed with 'L' type or 'J' type hooks or cranked bolts in roof, walls etc complete all as specified and directed

S&F Asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with J / L bolts complete all as specified and directed

M&L for providing cement concrete 1:2:4 type B0 ( using 12.5 mm graded stone aggregates ) as in coping , apex stone , bed plate , kerbs including weathering , slightly rounded or chamferred angles and throating and incl. necessary form work complete all as specified and directed.

Dismantling unframed timber scantlings 40 Sqcm & over in section, in any position complete all as specified and directed.

M&L for mild Steel Rolled tubular sections as in main and cross beams, hip and jack rafters; purlins Posts where connected to common rafters and angle cleats or other connecting plates incl wind ties etc Fe410 Gde E-250) Quality A complete all as specified and directed

S&F mild steel rolled section conforming to Fe-290 (Gde E-165), as in main and cross beams, hip and jack rafters, purlins where connected to common rafters fixed with angle cleats and other connecting plates etc. complete all as specified and directed.

S&F Stainless Steel framed work such as grills, railings fixed with nut bolts incl, cutting drilling holes etc., with ends of bars shouldered and/ or riveted, similar work conforming to Fe 290 Gde E 165 complete all as specified and directed.

S&F Mild steel bolts, purpose made, with hexagonal / square head one end & screwed the other/ screwed both ends; each screwed end to be fitted with washers & one hexagonal or square nut, exc 30cm long dia of neck n exc 12 mm complete all as specified and directed.

M&L applying two coats of systhetic enamel paint over a coal of red oxide / zinc chrome primer on surfaces of any description, over 10cm width or girth, not otherwise described on new steel surfaces including preparation of new steel surfaces complete all as specified and directed

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) n exc 1.5 sqm each etc complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each complete all as specified and directed.

S&F for Winpire 3 track pre painted steel sliding window 3-track, 2glass panel and 1 mesh panel ,sliding window fabricated from roll formed section made of galvanized steel colour coated/powder coated (base steel as per IS 513 D quality galvanized as per IS 277 with Zinc of 120gm/sqm ) with total coated thickness of 0.58mm primer coat with epoxy primer of 5-7 micron thick ,finish painted with a polyester paint of 12-16 micron thick and back coated with alkyd backer of 5-7 micron or powder coated with pure polyester up to 50-60 micron thick. section for external frame should be off 107X44 mm, section of shutter should be of 35 x 49 mm. section of mesh should be 35 x 49 mm . the window should be paneled with 5mm thick plain flot glass and stainless steel wire cloth with 0.36mm nominal dia of wire and average width of aperture 1.18mm. Corner bracket for internal and external frame made of glass filled nylon. Gaskets are to be made of Ethyl Propylene Diamine Monomer (EPDM) . The sections are to be cut to length, join and assembled by mean of corner bracket . The above frames should be fixed to the concrete/ masonary wall by means of self expanding screws. all as specified and directed by Engr-in-Charge (Make: NCL ALLTEK & SECCOLOR LTD or equivalent make as approved by GE)

S&F glazed 12mm thick toughened glass with frosted film and aluminium partition powder coated consists of top frame size 65x40mm any No of panels with incl. necessary joining cleats, glazing clips etc complete (Al. section thickness 2mm). conforming to IS. Glass Make : Modiguard, Saint Gobian etc, Aluminium Make- Jindal Aluminium/ Man Industries or equivalent as approved by GE complete all as specified and directed.

S&F glazed 12mm thick toughened glass with frosted film as in door, including SS handles not less than 200mm long-02 Nos and suitable locking arrangement, heavy type floor spring, locks and all necessary fittings complete allspecified and as directed

S& F glazed aluminum door powder coated of any colour consisting of frame of 63mm x 38 mm size with shutter fixed on frame both side openable on pivotal arrangement with including necessary cutting holes in wall & floor Door shutter consists of top rail size is 83 x 44 mm , bottom rail & lock rail size is 110 x 44 mm & style of door shutter is 83mmx 44 mm glazed with 5mm thick tinted /colour glassof approved make with handles 2 Nos in each door , hinges has fitted on frame as required fixed with rubber gasket & aluminum beading any No of panels with aluminum handle , locking arrangemen,floor spring and floor door stopper incl. necessary joining cleats , glazing clips etc complete (Al. section thickness 2 mm } ) confirming to IS complete all as specified and directed.. Make - Jindal Aluminum / Man Industries or equivalent as approved by GE.

S&F aluminium windows and ventilators sliding type three track powder coated consisting of frame 91.80 mm x 45 mm shutters 39 mm x 18 mm with rollers and locking arrangements with 4 mm thick plain glass with rubber gasket and aluminium beading , Al. handle, stainless steel wire mess 0.30mm nominal dia of wire and average width of aperture 1.40mm etc including necessary cutting holes on wall and floor and confirming to IS complete all as directed by Engr-in- Charge (Al. section thickness 1.50 mm }

S&F steel window with side hung shutter incl. box type hinges with steel handle, and steel peg stay, 100mm long MS tower bolt , 25mmx3mm mild steel flat iron 200 mm long hold fasts complete with glazing bar and MS grill/guard bars dovetailed or welded etc complete all as specified and directed..

S & F steel window with side hung shutter incl. box type hinges with steel handle and steel peg stay, 100mm long MS tower bolt , 25mmx3mm mild steel flat 200 mm long hold fast complete without glazing bar and MS grill/guard bars dovetailed or welded etc complete all as specified and directed.

S&F Mild steel door consisting of MS angle iron frame of 40x40x5mm with MS shutter with MS angle iron shutters frame 35 mm X 35 mm X 5 mm in two panel covered with 1.25 mm thick MS plain black sheet,sheet welded with 14X 3 mm thick flat all around of panel,30X30X5 mm tee fixed in between shutter partition, welded to with 2 Nos sliding door bolt of 16 mm dia 300 mm long with locking arrangement, 2 Nos of tower bolt of 200 mm long including MS angle iron frame 40mm x40mmx5 mm as in chowkhat with 6 Nos hold fast of flat iron 30mm X5 mm ,200 mm long with bottom flat iron of size 30mmx5mm and 100 mm size 4 Nos butt hinges including necessary cutting, welding, binding as required with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces complete all as specified and as directed. [Single shutters of approx width0.8 to 1.2 m and ht 1.9 to 2.10 M.]

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in foundation filling, sub base and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) as in plinth protection 75mm thick finishing cement concrete surfaces even & smooth without using extra cement including forming construction joint of size 10mm x 20mm filled with sealing compound grade A. complete all as specified and directed.

M&L for preparation of old AC roof sheet surfaces of any description over 10 cm width or girth and applying two coat of teracota weather proof paint over a coat of primer complete as specified and as directed.

S&F in repair 300mm long brass sliding door bolt with with sand or die cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed.

S&F in repair 150 mm size brass handles, cast type, polished bright complete all as specified and directed.

M&L for removal of synthetic enamel paint from old wooden surface of door or window of any description, width or girth including cleaning and preparation of surfaces including a coat of wood filler and applying two coats of French polishing on prepared wooden surfaces complete all as specified and directed.

S&F 1000 ltr capacity of rotational moulded polyethyline water storage tank three layered wall construction (cylindrical vertical with closed top) hoisted & fixed in position incl S&F 20mm dia GI Pipe medium grade washout pipe 450mm long with plug & 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittings including 01 Nos 20/25mm float valve complete all as specified & as directed including dismantling water tanks complete all as specified and directed.

S&F 500 ltr capacity of rotational moulded polyethyline water storage tank three layered wall construction (cylindrical vertical with closed top) hoisted & fixed in position incl S&F 20mm dia GI Pipe medium grade washout pipe 450mm long with plug & 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittings 01 Nos 15/20mm float valve complete all as specified & as directed including dismantling water tanks complete all as specified and directed.

M&L for one coat of oil emulsion distemper on old decorated surface of walls with synthetic distemper incl preparation of surfaces by removing of nails, making good holes /craks with cement mortor etc and washing floors, cleaning glass, joinery , electric fitting washing rubbing down and stopping of distempered and painted surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed.

M&L for complete removal of existing treatment from wall by scrapping etc and applying two coats of exterior emulsion weather proof paint over one coat of exterior wall primer incl. preparation of surfaces of old decorated walls etc, properly making of v shape crakes and filling of all crakes with crakes seal of walls complete all as specified and directed by Engr-in-charge. Make:- Asian ACE or equivalent make as approved by GE

M&L for water proofing treatment over roof surface including roughening surface and removing /taking down old treatment any type of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed as under:-

M&L for 10mm thick plaster in CM 1:4 mixed with and including water proofing compound @ 3% by weight of cement applied over roof slab complete all as specified and directed.

The surface of roof, parapet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut .

Oil based Bitumen primer conforming to IS-3384-1986 @ 0.3 kg per sqm to be applied on prepared surface till the surface is properly impregnated.

Applying one coat of hot blown bitumen of 85/25 grade @ 1.20 kg/Sqm.

Laying of water proofing APP modified polymeric water proofing membrane of weight not less than 3 Kg / sqm composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is sandwitched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc.

Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces, complete all as specified and directed at site .

Dismantling of posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good distrurbed ground in concrete complete all as specified and directed.

Dismantling of fencing wire mesh, any type complete all as directed

Supply only chain link fencing with 4mm dia GI wire, with 75x75mm mesh weight not less than 1.75 Kg per sqm fixed to fencing post of any type complete all as specified and directed. Make:- TATA/SAIL/JINDAL

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provission of binding wire complete all as specified and directed.

S&F in repairs galvanised, 2 strand , steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails staining bolts, incl securing or tying at crossings with and provn of galvanised mild steel wire, staples or steel pins, etc complete all as specicifed and directed. ( each line wire to be measured.

S&F MS framed work as in doors or gates designer type of any section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering confirming to Fe 290 (Gde E 165) . Door, etc to be prepared for hanging or sliding with and including, either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as specicifed and directed.

Excavating hard/dense soil in post holes (or similar holes) each n.exc 0.5 Cu.m getting out and removing surplus soil to a distance in exc 50m and making good surface complete all as specified and directed.

S&F MS angle as in fencing post, strut cutting tops in shape incl all necessary drilling, notching and reveting etc and similar work conforming to Fe 410-0 complete all as specified and directed.

S&F wind ties format including securing bolts posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessay drilling bolting or riveting etc, and similar work confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for mild steel round bar/TMT 8 mm and over as in tightening of chain link fencing including cutting to shape, necessary drilling, bolting etc Fe-410-W (Gde E-250) quality -A or Fe 290 (Gde-E-165) complete all as specicifed and directed.

Taking down carefully copper/aluminum pt wiring (light fan, socket or power) complete including fittings such as switches, sockets, c/roses, lamp holders, tube light fittings, sketch fittings, wooden boards, bell push, call bell, MCBs, & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall/floor complete all as specified and directed

Taking down main switches/DBs/ VTPN/AC box of any capacity complete all as specified and directed

M&L for concealed point wiring for one light/ fan point controlled by one switch with 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, , including of junction and terminal boxes, all fittings such as tees, bends, elbows, etc.all as per site requirements including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed Make of wire– Havells/polycab/Finolex

All as per Srl item No.72 above but for one call bell point controlled by one push button switch

All as per Srl item No.72 above but for one 5 Amp independent socket point using sunken box controlled by one switch.

All as per Srl item No.72 above but for one socket point controlled by one switch on same board

All as per item No 72 here-in-before but for concealed power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead. Make–Havells/polycabFinolex .

M&L for point wiring for one light point or fan point controlled by one switch with 1.5 Sqmm PVC insulated FRLS, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC trunking of size not less than 20mm ISI marked ivory white with all accessories such as tee, bend, joint cover including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed. Make of wire – Havells/polycab/Finolex

All as per Srl item No.77 above but for one Call Bell point controlled by one push button switch

All as per Srl item No.77 above but for 5Amp independent socket point controlled by one switch

All as per Srl item No.77 above but for one 3 pin ,5 Amp socket point with other switch on the same board

All as per item No. 77 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

M&L for concealed point wiring for one light point or fan point controlled by one switch with 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate of suitable module with frame as per site requirement all fittings such as tees, bends, elbows, etc. all as per site requirements PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed. Make of wire – Havells/polycab/Finolex .

All as per Srl item No.82 above but for one Call Bell point controlled by one push button switch

All as per Srl item No.82 above but for 5Amp independent socket point controlled by one switch

All as per Srl item No.82 above but for one 3 pin ,5 Amp socket point with other switch on the same board

All as per Srl item No. 82 here in before but for power point wiring using with 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as con complete all as specified and directd. Make– Havells/PolycabFinolex

S&F modular switch, one way,6 Amp 230, 1 module complete all as specified and directed. Make- Havells /Plaza/L&T

S&F modular socket 6 Amp-2/3 pin combined 2 module complete all as specified and directed. Make- Havells /Plaza/L&T

S&F modular switch, one way,6 A/16 Amp 230, 1 module complete all as specified and directed. Make-Havells /Plaza/L&T

S&F modular socket 6 A/16-2/3 pin combined 2 module complete all as specified and directed. Make-Havells /Plaza/L&T

S&F modular fan step regulator 120 Watt -2 module complete all as specified and directed. Make-Havells /Plaza/L&T

S&F modular bell push 6A one module complete all as specified and directed. Make- Havells /Plaza/L&T

S&F switch piano type flush, single pole, one way 5 A 230 V complete all as specified and directed. Make-Havells Reo series/ L&T/Plaza

S&F socket outlet, 5 pin, 5 Amp, flush type, 230 V complete all as specified and directed. Make-Havells Reo series/ L&T/Plaza.

S&F switch piano type flush, single pole, one way 15 A 230 V complete all as specified and directed. Make-Havells Reo series/L&T/Plaza.

S&F socket outlet 2 in 1,6 pin, 5/15 A, flush piano type 240 V complete all as specified and directed. Make-Havells Reo series/L&T/plaza.

S&F ceiling rose, surface backlite, three terminal complete all as specified and directed. Make-Havells Reo series/L&T/Plaza

S&F lamp holder insulated with back plate suitable for Angle/Batten fitting complete all as specified and directed. Make- Havells Reo series/L&T/Plaza

S&F call bell ding dong type 230 volt including T.W. board closed recessed type covered with mica sheet complete all as specified and directed. Make-Havells Reo series/L&T/Plaza.

S&F bell push flush type one way 5Amp 240 Volt complete all as specified and directed. Make-Havells Reo series/ L&T/Plaza.

M&L concealed sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit conduit less than 20mm dia ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed. Make of wire– Havells/Polycab/Finolex

M&L surface conduit sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit conduit PVC trunking of suitable size . ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as directed by Engineer-in-Charge Make of wire – Havells/Polycab/Finolex

M&L sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 4 sqmm (for main current) drawn in & incl PVC Casing-n-caping of suitable size ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 4 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed Make– Havells/polycabFinolex

M&L sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 2.5 sqmm (for main current) drawn in & incl PVC Casing-n-caping of suitable size ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 2.5 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as directed by Engineer-in-Charge Make– Havells/polycabFinolex

S&F testing and commissioning of MCB SP 240 volt 6 Amp to 32 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. (Make- Legrand/C&S/ABB)

S&F testing and commissioning of MCB SPN 240 volt 16 Amp to 32 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. ((Make-Legrand/havells/ABB)

S&F testing and commissioning of MCB SPN 240 volt 40 Amp to 63 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. ((Make- Legrand/havells/ABB)

S&F testing and commissioning of MCB SP 240 volt 40 Amp to 63Amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. (Make- Legrand/havells/ABB)

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar incl TW board of suitable size complete all as specified and directed. (Make- Legrand/havells/ABB)

S&F double door metallic sheet metal enclosure for DB double door(IP-42/43) When MCBs to be used SPN 4 ways, 240 V with 200Amps rated bus bar complete all as specified and directed. (Make- Legrand/ havells/ABB)

S&F electronic double space rotary 5 speed type regulator 120-280 V complete all as specified and directed. Make-Havells Reo series/L&T/plaza

S&F FLEXION LED DIGITAL RGB STRIP flexible LED strip uses high brightness SMD LED as the light source for indoor application only including LED driver, with wide viewing angle for good light distribution, easy to install complete all as specified and directed by engir-in-charge. Make-Havells cat part no LHEHDNPNUN4F024 /CG/ Wipro all as specified and directed.

S&F post top energy saving, environment friendly long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LED as light source all as specified and directed by Engr -in -Charge . Make - Havells Cat part No CORALPT35WLED757PSYMTOPC or equivalent in Bajaj/CG

S&F 2 X 2 ultra modern recess mounting luminaire with high brightness 36 Watt LED package and Unique pattern acrylic de-glaring diffuser sheet for glare-free uniform light distribution suitable for armstrong/grid ceiling with electronic driver complete all as specified and directed . Make-Havells cat part no PLANO2X2PLR36WLED857S /BAJAJ cat part no BZRSQL 36W GZi WH LED/CG

S&FLED Bulk head designed for modern homes availave in PIR as well as non PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer complete all as specified and directed. Make-Havells cat part No. LHEXCGP7UN5W013 /BAJAJ /CG.

Supply and fixing 9 watt LED bulb complete all as specified and directed. Make - Havells/Bajaj/Crompton/Wipro

Supply and fixing LED TUBE ROD 20W with single side connection for fitting with PC body complete all as specified and directed. Make - Havells cat part no LHLDEFXD5L8R020 or eqvt /Bajaj/Crompton

M&L LED TL fitting 20 watt for surface and wall mounted LED batten with ultra slim polycarbonate LED lighting fixture with high lumen output environmental friendly energy efficient complete all as specified and directed. Make-Havells Cat Part N0 LHEXACP7IN1W020 LED 6500K 4 feet or eqvt in Phillips/CG.

S&F double door metallic sheet metal enclosure for DB double door(DPX-125 ) VTPN 4 Way 415 Volts with 200 Amps rated bus bars IP 43- "IK 09 complete all as specified and directed. Make-Havells/ L&T/Legrand

S&F MCCB 63 Amps 4 pole, 415 V 16 KA complete all as specified and directed. Make- Havells / L&T/Legrand

S&F box type LED optic fitting 1x9 Watt 2 feet box type complete all as specified and directed .Make:Havellls /Wipro/CG

M&L for provn of earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate no 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. .Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs.

S&F or layng in ground 1100 Volts grade heavyduty 2 Run x single core cable PVC insulated aluminium conductor ,served with inner sheathing of PVC tape and overall PVC sheathed 2 Run x single core cable 10 Sqmm in garden light ,lawn etc including PVC rigid pipe complete all as specified and directed with (Make– HAVELLS/POLYCAB / PLAZA /ANCHOR) all as per directed .(Note:- The quoted rate shall be deemed to included the earthwork if required in garden or lawn )

v k builder

S Balwinder Singh

M K Construction

M/s JAYPEE ENTERPRISES

maharaja construction and suppliers