Reconstruction of Community Hall at Baghwanpora Lal Bazar near Bilaliya

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge In cement mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) From brick work in cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead of area of 3 sqm. and below

Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge In cement mortar

Demolishing and dismentling of unserviceable bath fixtures including GI/PPR/PVC fittings complete job as per the directions of Engineer in charge

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge all kinds of soil.

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed all kinds of soil within a lead of 50M from edge of cutting.

Providing & laying stone soiling including compacting, watering including all carriages of material complete

Labour charges for providing and laying stone solling including compacting,watering,material available at site. Solling available at site recovered from dismentling of stone masonary in plinth (item No. 05)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement 1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns

Centring and shuttering including strutting, propping etc. and removal of form work for Columns, pillars, piers, abutments, posts and struts.

Centring and shuttering including strutting, propping etc. and removal of form work for Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form work for Suspended floors, roofs, landings, balconies and access platforms Shelves (cast-in-situ)

Centering and shuttering including strutting, propping etc. and removal of form for under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium tensile steel bars

Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing withwater and allowing it to dry, all complete as per direction of Engineer-In- Charge bars above 12 mm diameter

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Labour Charges for providing and laying available filling in plinth recovered from dismantling of RCC work. Filling available at site recovered from dismentling of RCC work in slab and beams (item No. 01) 75% of RCC dismentaled material

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Labour Charges for Providing of Bricks work with available (Non-Modular) bricks of class designation 7.5 in foundation and above plinth including curing in cement mortor 1 cement: 6 fine sand mortor. Available quantity recoved from dismantling of brick work (item No. 03)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete 40mm thick with 20 mm nominal size stone aggregate.

12mm Cement plaster of mix 1: 6 (1 cement: 6 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab over 0.5 sqm

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fateners of required dia and length (hold fast lugs or with dash fasteners shall be paid for sapertately) first class impoted silver wood

Providing and fixing of 40*5mm MS Hold Fast 40cm long including fixing to frames embedded in cment conrete blocks in 1:3:6 Mic including all charges.

Providing and fixing of 35mm thick panelled or panelled and glazed shutters for doors windows and clerestory windows fixing with butt hinges of required size with necessary screws including penelling for panelled or panelled and glazed shutters 25mm to 40mm thick all complete as per directions of Engineer in charge 2nd class kail wood including fixing of pannels in 2nd class kail wood

Providing and fixing glazed 35mm thick shutters for foors windows and clerestory windows using 4mm thick float glass panes including ISI Marked M.S pressed butt hinges bright finished of required size with necessary screws 2nd class kail wood

Providing and fixing 4MM thick float glass in glazed doors windows and clerestory window shutters including cost of wooden beading complete job as per directions of Engineer in charge

Providing and fixing of the following Alluminium Hardware fittings. (A) Brass coated Handle 12'' Long

Providing and fixing of the following Alluminium Hardware fittings. (B) Brass coated Handle 09'' Long

Providing and fixing of the following Alluminium Hardware fittings. (C) Aidrop 12'' long

Providing and fixing of the following Alluminium Hardware fittings. (D)Tower bolt Brass coated 9'' long

Providing and fixing of the following Alluminium Hardware fittings. (E)Tower bolt Brass coated 6'' long

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture

Construction of bricks masonary manhole in cement mortor 1:4 (1 cement:4 coarse sand) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortor 1:3 (1 cement:3 coarse sand) finished with floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size finished with a floating coat of neat cement complete size 45*45*45cm deep including PVC manholes cover with frame

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10-liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing of PVC pipe (Type B) in proper Gradient. (A) 150MM dia

Providing and fixing of PVC pipe (Type B) in proper Gradient. (B) 100MM dia

Providing and fixing of PVC pipe (Type B) in proper Gradient. (C) 75MM dia

Providing and fixing of PVC pipe (Type B) in proper Gradient. (D) 100MM dia Plain Bend

Providing and fixing of PVC pipe (Type B) in proper Gradient. (E) 100MM dia Plain Bend

Providing and fixing of PVC pipe (Type B) in proper Gradient. (F) 100MM dia Plain Tee

Providing and fixing of PVC pipe (Type B) in proper Gradient. (G) 100MM dia Door bend

Providing and fixing of PVC pipe (Type B) in proper Gradient. (H) reducer 100mm to 75mm

Providing and fixing of PVC pipe (Type B) in proper Gradient. (I) 75MM dia plain bend

Providing and fixing of PVC pipe (Type B) in proper Gradient. (J) 75MM dia floor trap

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. 20mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge 25mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge 32mm nominal outer dia pipes

Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

Providing and fixing of two in one angle valve of approved make including all accessories complete.

Providing and fixing of wall mixer of approved make including all accessories complete.

Providing and fixing of Health Fuacet with chain of approved make including all accessories complete.

Providing and fixing of CP Towel Rod 600mm long of approved make including all accessories complete.

Providing and fixing of CP soap case of approved make including all accessories complete.

Providing and fixing of CP connection 600mm-450mm long of approved make including all accessories complete.

Providing and fixing of CP grating of approved make including all accessories complete.

Providing and fixing of CP Brass extension nipple (Size 15mm*50mm) of approved make and quality as per directions of Engineer in charge

Providing and fixing of CP cups of approved make including all accessories complete.

Providing and fixing of Stain less steel paper holder with stand of approved make including all accessories complete.

Providing and fixing of Stain less steel paddle operated dustbin of approved make including all accessories complete.

Providing and fixing of the 300mm*300mm exhaust fan (Crompton make) as per approved specification complete.

Providing and fixing of 50ltr water heater (Geysers) of approved make including cost of dash fasteners with nuts and washers complete (Jakwar,Racolid, Hindware)

Providing and fixing 600x450 mm beveled edge mirror of superior glass(of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality. 20.15.1.1 Rectangular shape 600x450 internal dimensions

Providing and laying of 25mm dia PVC conduit Pip embedded in slab/walls or any other concrete structure complete job as per directions.

Providing and laying of conceal light box

Providing and laying of conceal fan box

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixingand erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry: 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self- healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakage for horizontal surface one coat @1.10 kg per sqm

Providing hoisting and fixing trusses/ Purlins /rafters /Posts/post plates or like components including cost of screws etc complete

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required 0.50 mm thick with zinc coating not less than 275 gram/m2 852.50

Charges for providing of consultancy service for architectural design and structural design including conducting of Geo Techenical investigation for the propossed building complete job

Carriages of Mechenical Transport for sand

Carriages of Mechenical Transport for Stone aggregate

Bricks (20 kmt lead)