SPL REPAIR TO BDY WALL,PATH,DRAIN AND HARDSTANDING AT DRONACHAL BASE AND PROVN OF TOUGHENED GLASS DOOR PARTITIONS STEPS AND SHED WORKS AT DRONACHAL TOP UNDER GE DRONACHAL BHOPAL.

Amount

Demolition of brick work or stone /boulder masonry built in cement mortar including all quoins, arches, pillers etc. but excluding ashlar facings, dressed stone work and precast conc rete articles.

Demolition of PCC in ground floor and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed

Dismantling of plain or corrugated steel sheeting, any guage, thickness, including nainital or similar pattern roof coverings etc.

M&L for PCC 1:3:6 (type C2) (using 40 mm graded stone aggregate) as in foundation filling and mass concrete

M&L for Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete (Nominal mix) in type A-1, 1:1.5:3 (using 20 mm graded stone aggregate) for Walls, retaining walls, ballast walls, like any thickness; above top of fooitngs; including attached pilaster and buttreses complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing precast cement concrete Type B1 1:2:4 (20mm graded stone aggregate) as in cover slabs (for manholes, drains etc.) of any size and thickness as required Set in cement mortar 1:4 Note :- Reinforcement will be measured and paid saperately

M&L, for reinforced cement concrete (Nominal mix) in type A-1, 1:1.5:3 (using 20 mm graded stone aggregate) for Foundations, including rafts, footings, plinth beam, Columns, pillars, piers, post and struts and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to sharp required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) but less than 0.9 mm dia Securing with clips .

Supply & fixing 6 to 8mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed

M&L for formwork to sides of concrete Foundations, footings, bases of columns, raft and rft beams, plinth beam, vertical or batter etc. for rough finished surfaces of concrete surfaces all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm grade stone aggregate) as in coping complete all specified and as directed.

M&l for rendering 15mm thick cement plaster in CM 1:4 and even using integral waterproofing compound @ 3% by weight of cement on fair faces of brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed. Note:-Supply only of water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound

M&L for three coats of white wash including preparation of new concrete surfaces of drain and wall etc all as specified.

Preparation of newly plastered surfaces of walls priming plastered and other surfaces with alkali-resitant priming paint and applying two coats of cement base paint complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M&L for mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming to Fe410-S.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st -240 complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as sub base floor complete all as specified and directed by Engineer-in-Charge.

M & L for sand filling under floors or in fdn including watering and consolidation as in bedding layers for laying tiles.

M&L for factory made Machine pressed precast concrete interlocking paver blocks any shape and size confriming to IS 15658-2006 of 60mm thickness coloured chemically treated PCC (ISI Marked ) M-35 grade of desgin & pattern approved by GE as in footpath and filling of joints with Narmada fine sand complete all speciified and directed by Engineer-in-Charge.

M & L Machanic pressed precast concrete interlocking paver block any shape and 80mm thickness, jointed and pointed with grey cement and pigment in floor/ footpath.

Dismantling of interlocking tiles of any size or any description for floor/path laid dry and pointed in cement mortar complete all speciified and directed. Note:- Serviceable tiles shall be stacked and fixed under relevent items.

M&L for except tiles Machine pressed precast concrete interlocking paver blocks any shape and size of 60mm thickness coloured of desgin & pattern refixing in floor/footpath and led over Narmada fine sand complete all speciified and directed by Engineer-in-Charge.

M&L for forming construction (dummy) joints 65mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished even and smooth using with extra cement

Dismantling of existing RCC/ Steel /Wooden posts or struts (wood, steel or R.C.C.) any section,concrete ,brick work ,massonery etc . including taking out embedded portion and making good disturbed ground complete all speciified and directed

S&F, angle iron (Fe-310) as in posts, struts in fencing including cutting top to shape required, drilling holes, notching for wire etc (IS angle 60x60x5mm) complete all speciified and directed

S&F steel flat iron including necessary drilling hole bolting or reveting etc and similar work complete conforming to Fe -290 Gde E - 165 (40mm width 4mm thick) complete all speciified and directed

M&L for MS round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for fencing, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all speciified and directed

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed by Engineer-in-Charge.

Dismantling fencing wire mesh, any type.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F, galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire complete all as speciified and directed

M&L for reinforced concrete pipes, class NP2, 600mm bore with collar joint with 1:4 CM laid in tranches complete all as speciified and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 metre wide & not exc 1.5 mtr in depth: for foundationetc or for manholes, laying of pipe in any type of soil and getting out complete all as specified.

Returning filling in soil, including spreading, leveling watering & well rammng in layers not exc 25cm thick complete all as specified and directed.

Removing excavated material (Soil) to a distance not exc 50 mtr & depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified & diected.

Material and labour for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including cement screed of 15mm thick in CM 1:6 laid & jointed with gray cement slorry mixed with pigment to match the shade of the slab complete all as specified and as directed.

All as per item No 43 but in skirting, vertical surface dadoes and riser etc over and including 10mm thick rendring in CM (1:4) complete all as specified and directed.

Supply and fixing12mm thick toughned glass as in hinged doors, fixed partitions automatic doors and similar work includingcutting to shape, drilling holes required.

Supply and fixing12mm thick figured toughned glass as in hinged doors, fixed partitions automatic doors and similar work includingcutting to shape, drilling holes required

Supply only fancy type heavy duty stainless steel brackets for fixing of toughned glass partitions etc.

Supply only heavy duty hydraulic floor door spring fixed to floor for heavy toughned glass door including top SS bracket with pivot for for fixing of glass door with glass partition .

Supply & fix only fancy type lock for toughned glass door

Supply and fixing long fancy stainless steel handle made out of stainless steel pipe fixed to toughned glass door

Supply & fix steel work in tubular trusses round shape above MS stair including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in Soft/disintegrated rock and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface.

Material and labour plain cement concrete type D2 1:4:8 (40mm graded aggregate) as in foundation filling , ramp concrete under floor or in mass concrete in any thickness and slope as directed by Engineer-In-Charge .

Supply and fixing 304 grade stainless steel pipe 100mm dia of any thickness used as column for supporting mild steel tublar truss

Supply and fix 6mm thick hollow polycarbanate sheet of any colour fixed with railing / ms truss with self driving screws with washer rubber as required and joint of two seats will be filled with silicon weather proof sealant covered with 50mm x 7mm stainless steel channel on edges and fixed to wall / roof complete.

Supply and fixing plates,(plain or cheqered) channels,square cut or notched ( ordinary and counter sunk) forming holes,with riveted, bolted or welded attachment all as specified and directed by Engineer in charge.

Material and labour for preparation of new steel surfaces of any discripton not otherwise discribed not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spcified and as directed.

Material and labour for 75mm thick plain cement concrete type D2 (1:4:8)(40mm graded aggregate) as in sub base of floor, path etc,complete all as specified and directed.

M/s VIKAS TRADERS

RAJPATI CONSTRUCTION

deepak mehra & associates

CREATIVE CONSTRUCTION

SATHI ENTERPRISES