RENOVATION OF VELOCITY TUNNEL BUILDING NO 238 AND 239 AT ARDE PASHAN, PUNE

Amount

Dismantling floor, hearth or wall tiling 10mm to 25mm thick including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Demolishing cement concrete of any description and any position not otherwise specially provided for including disposal of material within 50 metres lead complete all as specified and directed.

M&L for Cement concrete 1:2:4 as in sub base of floor and in pavements, laid to required slope and camber in panels as required including consolidation finishing, tamping and necessary formwork complete all as specified and directed.

Providing and laying double charged Vitrified tiles of size 600mm x 600mm in floor (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid over and including 20 mm thick screed bed in cement mortar 1:4 jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.complete all as specified and directed.

Providing and laying double charged vitrified tiles of size 600x600mm in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, laid over and including 12 mm thick rendering in cement mortar 1:3 (1 cement: 3 manufactured sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete all as specified and directed.

Taking out doors, windows and clerestory window shutters of area 3 sq. metres and below (steel or wood) including stacking within 50 metres lead complete all as specified and directed.

Providing and fixing aluminium frame work for doors, windows (three track), ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be Powder coated (minimum thickness of powder coating 50 micron) smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)

Providing and fixing for aluminium shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required aluminium sections shall be Powder coated (minimum thickness of powder coating 50 micron) including the cost of EPDM rubber / neoprene gasket required (including all necessary fittings) complete all as specified and directed.

S & F Pressed steel door frames (mild steel sheet 1.60 mm) Profile "B" of size 105X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed.

M&L for plain cement concrete Type C1, 1:3:6 ( using 20 mm graded aggregate) for filling of hollow pressed steel frame complete all as specified and directed.

Providing and fixing ISI marked flush door shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and directed.

M & L for Painting new wooden surfaces with two coats of synthetic enamel paint of approved brand and manufacture of required colour to give an even shade over a coat of pink primer of suitable shade with ordinary paint of approved brand and manufacture complete all as specified and directed.

S & F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed, complete all as specified and directed.

S&F 150 mm long aluminum anodized barrel tower bolts of extruded section complete all as specified and directed.

S & F 125 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

Providing and fixing aluminium hanging floor door stopper, (Twin rubber stopper ) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete all as specified and directed.

Demolishing cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed.

Material and labour for PCC 1:2:4 (Type B0 using 12.5 mm graded aggregate) levelling course average thick 40 mm, to match the undulations of roof complete all as specified and directed.

Material and labour for rendering 10 mm thick on fair faces of concrete surface in cement mortar 1:3 for receive the roof finishes with water proofing liquid complete all as specified and directed. Note. WPL Shall be measured and paid separately

Material and labour for applying water based polyurethane modified dispersion (single component, cold applied, non toxic, VOC complaint) in 03 coats including 01 coat of epoxy primer @ 0.15 Kg per Sqm followed by two coats of polyurethane coating with 1.5 Kg per sqm in two coats etc complete per manufacturer specification and as directed by Garrison Engineer Notes:- (a) Properties of Polyurethane based chemical shall confirm to following Technical Parameters:- (i) Highly Elastic and shall have crack bridging ability of upto 3mm as per AS NZ 4548. (ii) UV Resistance. (iii) Adhesion to concrete and shall resist 7 bars of hydrostatic pressure. (iv) Tensile strength should not less than 2.0 N/sq.mm for free film & 60 % solid content as per ASTM C 1250. (v) Elongation should not less than 300% as per ASTM D2370. (vi) Solid content by weight should not less than 60%. (vii) Air/water permeability BSEN 12390 AT 5 bar -72 hours should be NIL and minimum dry film thickness of water proofing membrane must be 1.0mm. (viii) Accelerated weathering (ASTM453) should Pass 1000 hours. (ix) Reaction to fire – non inflammable.

(b) The work shall be executed through authorised applicator of manufacturer only. Contractor has to provide manufacturer test certificates for the above mentioned technical parameters and PVs (c) The contractor has to submit the guarantee for 10 Years against the water proofing treatment.

Supply only Liquid water proofing compound as per approved make, complete all as specified and as directed.

Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and as directed.

Material and labour for Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in cement mortar 1:6 complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead completeall as specified and directed.

Material and labour for 12mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces complete all as specified and directed.

Material and labour for 18 mm thick cement plaster in two coats under layer 12 mm thick cement plaster 1:4 finished with a top layer 6 mm thick cement plaster 1:6 including mixed with water proofing compound @3% by weight of cement complete all as specified and directed.

Material and labour for Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

Material and labour for Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on new work (three coats) over and including water thinnable priming coat with cement primer complete all as specified and directed.

Material and labour for preparation of newly plastered wall surface and applying two coat (Two coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology , Excellent Dirt Pick up resistance of over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed.

Material and labour for White washing three coats with lime to give an even shade complete all as specified and directed.

Material and labour for complete removal of existing treatment including fascias,cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by crack fill paste of Asian Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Asian Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio

as per manufacture's instruction and all coats including primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed. Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Notes :- (a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer andmanufacturer of paints and their authorized applicator before quoting the bids and submit the same alongwith performance security of tender. (c) Cost of scaffolding at any height shall be included in thequoted rate. (d) Preparation of plastered or unplastered surface or removal of existing treatment by scrapping of walls, chajjas, ceilings, fins, fascias, parapets etc shall be done by using mechanial sander with internal dust extraction system for clean environment

certified by the manufacturer. After the prepartion of surface written approval shall be obtained from GE before applying primer and further treatment/coats. Bldg wise stage passing register shall be maintained. (e) Finishes ie cement based paint, acrylic water based exterior grade primer,premium acrylic smooth exterior emulsion etc to walls, ceiling, chajjas, fins, fascias, prapets etc shall be applied using airlessspray technology and capable of operating single spray gun with a suitable hose length. the spray machine should be of areputed manufacturer with pro-guard technology and capability of tracking pressur as well as paint and primer usage (f) This equipment shall be certified by approved manufacturer. (g) The accessories for applying the finishes shall be spray in hard to reach areas and penetration of finishes on the surface so asto achieve uniform application and quality surface finish. (h) The contractor shall submit approved company generated 05 yrs warranty card at the time of submission of RAR and Final bill.

M&L for complete removal of existing treatment on wall and applying two coats distmper oil emulsion over a coat of alkali resistent primer complete all as specified and directed.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

M&L for Kota stone slab flooring over and including 25 mm (average) thick screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with screed bed of cement mortar 1 : 4 (1 cement : 4 manufactured sand) complete all as specified and directed.

M&L for Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid over and including 12 mm (average) thick cement mortar 1:3 (1 cement: 3 manufactured sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete all as specified and directed.

M&L for machine cut Cudappah stone slab 20 to 25mm thick in single piece as in platform of WHB or similar work bedded and jointed in cement slury complete all as specified and directed.

Providing and laying 18mm thick polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings laid over and including 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 manufactured sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing, moulding and polishing etc. complete all as specified and as directed .

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc fixed to steel window including priming coat with approved steel primer all complete all as specified and directed.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level complete all as specified and directed.

M & L for Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete all as specified and directed.

Dismantling G.I. pipes 15 mm to 40 mm nominal bore including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead complete all as specified and directed.

M & L for providing and fixing 15mm bore medium grade galvanished tube with and including all fitting & fixed complete to walls or ceiling & laid in floors including cutting and making good the walls complete all as specified and directed.

M & L for providing and fixing 15 mm nominal bore C.P. brass stop cock of standard design and of approved make conforming to IS:8931complete all as specified and directed.

M & L for providing and fixing white vitreous china pedestal type water closet ISI marked (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete all as specified and directed.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as specified and directed.

M & L for Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete all as speciied and directed.

M & L for Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 manactured sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete all as specified and directed.

Providing and fixing PTMT towel rail 600 mm long with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour complete all as specified and directed.

Providing and fixing health faucet of CP with 8mm dia, 1.2mtr long flexible tube with wall hook ore of approved quality conforming to IS:8931 complete all as specified and directed.

Providing and fixing two way bib cock C.P. brass 15mm bore of approved quality conforming to IS:8931 complete all as specified and directed.

Providing and fixing white Vitreous China Wash basin of size 630x450 mm with a single 15 mm C.P. brass pillar tap with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete all as specified and directed.

Providing and fixing toilet C.P. brass paper holder complete all as specified and directed.

Taking out doors, windows and clerestory window shutters of area Of area beyond 3 sq. metres (steel or wood) including stacking within 50 metres lead complete all as specified and directed.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead complete all as specified and directed.

M & L for Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete all as specified and directed.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners using M.S. angels 40x40x6 mm for diagonal braces, all necessary fittings complete, including applying a priming coat of approved steel primer complete all as specified and directed.

M & L for Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 manufactured sand derived from recycled concrete aggregates (RCA) : 6 graded stone aggregate 20 mm derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete all as specified and directed.

M & L for Painting with synthetic enamel paint two coats on new steel work over a coat of red oxide primer of approved brand and manufacture to give an even shade complete all as specified and directed.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 550 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during ransportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. complete all as specified and directed.

Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge.

S & F Factory made solid panel PVC door shutter 35 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed

S&F 100x75mm butt hinges extruded aluminum alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed.

S & F 100x10 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S& F extruded Aluminium alloy handles, fabricated type anodised size 100 mm complete all as specified and directed.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931complete all as specified and directed.

Supply and fix Unplasticised P.V.C. connection pipe 15 mm bore with brass union 45 cm long complete all as specified and directed.

Providing and fixing C.P. brass angle valve for basin, flush tank of approved quality conforming to IS:8931 complete all as specified and directed.

M&L Cast iron floor trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively including coupling and waste pipe complete all as specified and directed.

S&F CP Urinal spreader for urinal fixing with 15 mm dia pipe. complete all as specified and directed.

M & L for Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation, traverse etc. complete all as specified and directed.

S&F Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50mm dia wire for fixing of window, ventilator etc. complete all as specified and directed.

Providing and fixing plane tinted/frosted glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings as per directions of engineer-in-charge .

S&F Rough cast wired glass, 6.4mm thick area exc 0.50 Sqm and n.exc 0.75 Sqm glazing with packing rubber for window door etc. complete all as specified and directed.

Surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out all kind of soil and disposal of excavated earth upto 50 m and lift upto 1.5 m, complete all as specified and directed.

M & L for Providing of stone aggregate (Single size) : 63 mm nominal size including laying and rolling by mechinical complete all as specified and directed.

M & L for Providing and laying in position cement concrete 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) as a sub base complete all as specified and directed.

Providing and laying 80 mm thick C.C. paver block of M-40 grade with approved color design and pattern laid over and including 50mm thick compacted bed of manufactured sand, filling the joints with line sand etc. complete all as specified and directed.

Demolishing cement concrete 1:4:8 or leaner mix (i/c equivalent design mix) manually/ by mechanical means including disposal of material within 50 metres lead complete all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed. Note. Thickness of concrete slab is 100mm.

M & L for Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) getting out all kinds of soil and including returning, filling, disposal of excavated earth lead upto 50 m and lift upto 1.5 m, complete all as specified and directed.

Demolishing stone rubble masonry in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed.

M & L for Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 manufactured sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 complete all as specified and directed.

M & L for Providing and laying cement concrete 1:1½:3 (1 cement : 1½ Natural sand or crushed stone sand or crushed gravel sand as per IS1542 : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in coping (any thickness) up to floor five level, including centering, shuttering and finishing complete all as specified and directed.

M & L for Flush pointing on stone work with cement mortar 1:3 (1 cement : 3 Natural sand or crushed stone sand or crushed gravel sand as per IS1542) complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down sub main wiring of any size including ERW/PVC conduit/casing caping complete and making good the disturbed surfaces all as specified and as directed.

M & L for Point Wiring for light point/ fan point/exhaust fan point/call bell point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. as required complete all as specified and directed for the following :- (i) One light point controlled by one; one way switch

All as per item No 90.00 here-in-before but for One ceiling/Exhaust/ Wall fan point controlled by one; one way switch.

All as per item No 90.00 above but for One 3 pin 5 Amp socket out let controlled by one switch on independent board.

M & L for Wiring for circuit. Submain wiring along with earth wire with the 2 x 2.5 sq mm + 1 x 2.5 sq mm eath wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required for Power Point wiring complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

supplying and fixing 3 module (100 mm x 75 mm) size/modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required complete all as specified and directed.

Supply and fixing following modular switch/socket 15/16 Amp switch, 1 module on the existing modualar plate & switch box including connections but excluding modular plat etc. as required complete all as specified and directed.

All as per item No 95.00 above but for 6 Pin 15/16 A socket outlet.

All as per item No 95.00 here-in-before but for 3 Pin 5/6A Socket outlet.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required complete all as specified and directed.

Supply and fixing ceiling rose 3 terminal 240 volts, 5 Amps on wall/ceiling/roof surfaces complete all as specified and directed

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Taking down ceilling fan/exhaust fan of any sweep for servicing / repairing /maintenance, opening up, identifying and replacing the defecctive parts, cleaning, greasing, etc, reassembling and hanging up/fixing back at its original position, connecting up and testing complete all as specified and directed. Note : Cost of spares such as capacitors, bearings, etc will be measured and paid for separately under respective item of Schedule 'A' as supply only.

Supply only capacitor of 2.5 mfd for ceiling fan/exhaust fan complete all as specified and directed.

Supply only capacitor of 4 mfd for air circulator/exhaust fan complete all as specified and directed.

Supply only bearing No.6201/6202/6203/6204 or any other No matching to the existing size and suitable for ceiling fan/exhaust fan/wall mounted fan complete all as specified and directed.

M & L for Disconnecting electric connection and taking down carefully fan of any type and size/sweep as described below, removing the burntwinding of fan motor and cleaning the fan stator completely removing theburnt sludges from the slots and rewinding with super enameled copper winding wire of suitable guage or of matching size to the existing wires with same turns ratio including all insulating material such as insulation paper sleeve, sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and refixing to orginal position complete all as specified and directed. (i) Ceiling Fan of size 1200/1400mmsweep.

All as per item No 106.00 above but for Exhaust Fan 350/450 mm sweep.

M & L for Preparation of old surface of exhaust fan of any sweep by removing old paint using paint remover or by burning off using blow lamp and cleaning with cloth and spray painting complete exhaust fan with superior quality synthetic enamel paint (Smoke grey) after applying single coat of primer complete all as specified and directed.

M & L for Painting with superior quality enamel paint (Half White) on ceilling fan of size 1200/1400 mm complete all as specified and directed.

Material and labour for sub main wiring complete with 2 single core cable 4 sq mm PVC insulated FRLS stranded copper conductor cable 1100 volts grade drawn through and including PVC conduit and conduit accessories in surface/concealed with one run of PVC insulated FRLS cable 4 sqmm copper conductor cable ( green in colour ) for earth continuity conductor connected to main earth dolly complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

Material and labour for sub main wiring complete with 2 single core cable 6 sq mm PVC insulated FRLS stranded copper conductor cable 1100 volts grade drawn through and including PVC conduit and conduit accessories in surface/concealed with one run of PVC insulated FRLS cable 6 sqmm copper conductor cable ( green in colour ) for earth continuity conductor connected to main earth dolly complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

Supply and fix in replacement MCB DB 12 way SPN (double door) sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete as required at site as specified and directed.

S&F in replacement of MCB SPN 32-40 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve complete all as specified and directed.

Supply and fix inreplacement of MCB single pole 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve complete all as specified and directed.

Supply and fix in replacement MCB TPN DB 04 way (double door) sheet metal enclosure factory made suitable for MCB TPN incomer and MCBs as outgoing with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete as required at site as specified and directed.

S&F in replacement of MCB TPN 63 Amps working on 415 volts, 50 HZ AC, 10 KA ,'C' curve complete all as specified and directed.

S&F Copper plate 600 x 600 x 3 mm thick fixed to floor by means of brass nut/bolt and duly connected to ESDS (Electrostatic Static Discharge System) system complete all as specified and directed.

Supply and fixing copper plate 150 x 150 x 3 mm thick with 1 round solid copper bar 20 mm dia & 150 mm long brazed or threaded & fixed in the centre of the plate for manual electrostatic discharge & fixed on existing wall at a height of 1.5 metre and connected with copper strip 25 x 5 mm complete all as specified and directed.

Supply and fixing FAST Electrode earthing with Pure Copper Single Pipe, the pipe 3 metre long, dia is of 76 mm Pipe & wall thickness of pipe is 2.0 mm & the cavity is filled with highly conductive, non- corrosive material along with Supply of Fast Electrode Earth Enhancing Compound 2 Bag of 25 Kgs. The Earth Enhancing Compound should have Test certification from NABL accredited Lab.It should be tested as per IS 1350/ AHPA guideline’s. The pH value of Compound should be 7.59, Moisture % by mass should be 8.91 & Solubility in 1:1 HCL should be 32.29 %. The Compound should have test certification ELV Test as per protocol IEC 62321/111/54 /CDV /ICP-OES for contains of Lead (23.0 ppm), Cadmium (15.0ppm),Mercury (Below Detection Level) & Hexa-chromium(Below Detection Level). The manufacture of Earthing should be registered under Udyam registration and certified for ISO 9001:2015 including FRP Pit cover as required complete all as specified and directed. Note: Earth resistance should be less than 1 ohms. If the desired result of the earth resistance not comes under 01 ohms the contractor should fill extra earth compound with out extra payment to the Govt.

Supply and fixing Copper strip of 25 x 5 mm on surface or in recess for connections, laying in wall, floor etc. as required complete all as specified and directed.

Supply and fixing of modular type ,suitable for telephone socket outlet including GI box alongwith modular base &cover plates as required complete all as specified and directed.

Supplying and fixing of 20 mm size of steel conduit along with accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required for LAN / Telephone complete all as specified and directed.

Supplying and fixing 5 to 32A, 240V, SPN Industrial type socket outlet, with 2 Pole and earth, metal enclosed plug top along with 5 to 32A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the sokcket out let and complete with connections, testing and commissioning etc. as required for Air Conditioners complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 1.5 TR including remmoving &transporting unsv item to MES store yard complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 2 TR including remmoving &transporting unsv item to MES store yard complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and directed.

Taking down / dismantling existing perished aluminium strip of size 25x3 mm from wall/roof /burried in ground of conventional type lightening protection network system complete all as specified and as directed.

M & L for Refixing/Repair of serviceable aluminium strip of size 25x3.15mm obtained as per item No 128.00 above , at any type of building at any height including jointing system of conventional lightening protection network and making good the distrubed surfaces of wall/roof top match with existing surface complete all as specified and as directed.

Material and labour for Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

Supply and fix Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw including dismantling taking out old inspection box complete all as specified and directed.

Material and labour for Air termination, single pointed aluminium rod 12mm dia and 300mm long complete all as specified and directed.

Material and labour for PCC block of size 150 x 150 x 150mm in PCC (1:3:6) type C-1 with 20mm stone graded aggregate for fixing on roof conductor / air termination rod / GI strip etc. complete all as specified and directed including dismantling taking out old PCC block.

M & L for epoxy base insulator of suitable size, 35mm height fixed on PCC blocks / wall / MS angle / Pipe / channel/ on towers / on Galvalume sheet with and including bolt size 8 mm dia, 19 mm length, nuts and washers etc complete all as specified and directed including dismantling taking out old insulator complete all as specified and directed.

M & L for Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less' than 1.5meters below normal ground level, earth plate connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate connected to earth test point all as specified or indicated including testing on completion, including necessary excavation and earth work in any type of soil and edequate quantity of common salt & charcoal for alternate layer around the earth plate, including PCC (1:2:4) pit and 10mm thick C.I. cover with arrangement of hinge to 40x40x6mm C.I. angle iron frame, including 20mm dia G.I. pipe for watering purpose with the arrangement of funel and wire mess, including GI pipe of 15 dia for earth lead protection. complete all as specified and directed.

M & L for Providing and laying G.I.strip 32 mm X 6 mm from earth electrode directly in ground as required complete all as specified and directed.

Supply and fixing Mild steel with powder coated simens gray inspection boxes / test point boxes 250 x 200 x 100 mm made out of 16 gauge with top cover including provision of fixing of 2 Nos epoxy insulator with and including insulating PVC sheet for incoming and outgoing copper strip for proper insulation etc complete all as specified and directed.

S & F earth pit indicator made out of MS sheet of 16 SWG of size 30 x 20 cm welded to angle iron of size 25 x 25 x 3 mm at a height 1 M above ground including dismantling taking out old earth pit indicator complete all as specified and directed.

Taking down copper/aluminium normal / flame proof submain wiring in Steel conduit pipe any type/Size complete, including etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surface of walls, floors, etc. complete all as specified and directed.

M & L for Wiring for circuit/ submain wiring along with earth wire with the 2 x 1.5 sq mm + 1 x 1.5 s qmm eath wire of FRLS PVC insulated multi stranded copper conductor, single core cable in surface/ recessed steel conduit as required for One light point controlled by one rotary switch complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

All as per item No 140.00 above but for 3 pin 16 Amp socket out let controlled by 2 X 2.5 Sqmm + 1 x 2.5 sqmm earth wire complete all as specified and directedl. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

All as per item No 140.00 here-in-before but for 5 pin 16 Amp socket out let controlled by 2 X 4 Sqmm + 1 x 4 sqmm earth wire complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

Material and labour for sub main wiring complete with 2 single core cable 6 sqmm PVC insulated FRLS stranded copper conductor cable 1100 volts grade drawn through and including ERW conduit and conduit accessories in concealed with one run of PVC insulated FRLS 6 sqmm copper conductor cable ( green in colour ) for earth continuity conductor connected to main earth dolly complete all as specified and directed. Note : 3 runs of cable and one run of conduit shall be measured as one unit.

Material and labour for sub main wiring complete with 4 runs of single core cable 16 sqmm PVC insulated FRLS stranded copper conductor cable 1100 volts grade drawn through and including ERW conduit and conduit accessories in surface with two run of PVC insulated FRLS 16 sqmm copper conductor cable ( green in colour ) for earth continuity conductor connected to main earth dolly complete all as specified and directed. Note : 6 runs of cable and one run of conduit shall be measured as one unit.

S&F Flameproof / Weather proof LED 1 x 20 W Tube light fitting with lumen out put not less than 2000 Lumens, body made out of cast alluminium alloy LM6 Construction certified by CIMFR and PESO , ISI marked including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed.

S&F Flameproof / Weather proof LED 2 x 20 W Tube light fitting with lumen out put not less than 8000 Lumens, body made out of cast alluminium alloy LM6 Construction certified by CIMFR and PESO , ISI marked including suitable electronic including necessary fixing arrangments and connecting up complete all as specified and directed.

Supply and fixing Flame proof/Weather proof LED Flood light 1 X 150 watts with lumen out put not less than 15000 Lumens fittings, body made out of aluminium alloy LM -6 body epoxy painted along with suitable integrated electronic drivers; including necessary fixing arrangments CMRI approved and connecting up complete all as specified and directed .

Supply and fixingSwitch flame proof rotary type with termination box in LM6, 16A, single pole 250V size complete all as specified and directed.

Supply and fixing Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth, ISI marked complete all as specified and directed .

S&F flameproof switch socket combination 4P+E (5 Pin) suitable for 32 Amps, 415 volts including plug and top, LM-6 body, certified by CIMFR and PESO , ISI marked complete all as specified and directed .

Supply and fixing Flameproof wall mounting fan 610 mm (24") sweep, single phase, 230V, rated RPM 1440 complete all as specified and directed

Material and labour for Flameproof Exhaust fan of size 15'' sweep suitable for single phase 240 vlots, 0.25 Hp including louvers, LM-6 body epoxy painted CMRI certified, ISI marked complete all as specified and directed .

Supply and fix Flameproof pedestal fan of size 450 mm with louvers single phase 240 volt , 0.5 HP, 1414 RPM complete all as specified and directed.

M & L for Providing and laying 25 x5 mm copper strip on surface or in recess for connections etc. as required complete all as specified and directed.

Supply and fix Flame proof weather proof bend 3/4" (20 mm dia bore ) complete all as specified and directed.

Supply and fix Flame proof weather proof bend 1"(25 mm dia bore ) complete all as specified and directed.

Supply and fix Flame proof weather proof inspection elbow 3/4" complete all as specified and directed.

Supply and fix Flame proof weather proof inspection elbow 1" complete all as specified and directed.

Supply and fix Flame proof junction boxes LM-6 with plain cover suitable for 3 Way, 100 mm dia suitable for 20 mm dia conduit pipe complete all as specified and directed.

S&F Flame proof junction boxes LM-6 with plain cover suitable for 4 Way suitable for 20 mm to 25 mm dia conduit complete all as specified and directed.

Supply and Fix flameproof/Weatherproof distribution board LM6 enclousure material including copper busbar-04 Nos, busbar terminals (35 sq mm) -04 Nos, terminals 16 sq mm - 12 Nos, terminals 6 sq mm - 04 Nos, terminals 2.5 sq mm-20 Nos, internal wiring with, labels, cable entries bottom side as per cable schedule, construction material: Al die cast LM6, ingress protection: IP 65, Gas group: IIB+H2, certified by CIMFR Dhanbad & PESO Nagpur complete all as specified and directed by Engineer-in-charge. The distribution board comprising of the following:- Incoming: MCCB 160 Amps 4 pole 18 KA - 01 No Outgoing : a) MCB 63 Amp, 4P 10 KA - 03 Nos, b) MCB, SP, 6 to 32 amp, 10 KA, - 10 Nos, c) MCB, DP, 40 Amp, 10 KA-01 Nos

Taking down old unserviceable LT cables 3.5 Core 150 sq mm size from trenches including disconnecting cables and stacking of cables within 50 metres lead complete all as specified and directed.

Supplying and fixing of light class G.I. pipe of 100 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required complete all as specified and directed.

M & L for Cutting bajri paths and making good the same including supply of extra quantities of brick aggregate, moorum and red bajri required complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 Core 150 sqmm complete all as specified and directed. Note. Earth work, excavation RFR and removed of surplus rock/soil shall be measured and paid separately.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out/laying of HT/ LT under ground cable and getting out in soft soil earth strata complete all as specified and as directed:-

All as per item No 166.00 above, but in Hard soil.

All as per item No 166.00 here-in-before, but in Disintegrated rock.

All as per item No 166.00 above, but in Hard rock.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soils complete all as specified and directed.

Removing surplus excavated soil/rock to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Material and labour for dry crushed stone sand filling in trenches to required width at bottom and top of cable as cushioning including spreading leveling and consolidation all as specified and directed Note:punned thickness shall only be measured and paid.

and shall be consisting the following :- Incoming: MCCB thermal magnetic release, 4 pole, 250 amps, 25 KA breaking capacity-01No Outgoing: MCCB thermal magnetic release, 4 pole, 200 amps, 25 KA breaking capacity -01 No, MCCB thermal magnetic release, 4 pole100 amps 25 KA breaking capacity - 02 No, Basic digital multifunction meter - 01 No, Surface mounted LED (R,Y,B) indication lamp 22.5 mm dia suitable for 415V AC - 01 Set,

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm ISI marked complete all as specified and directed.

sanjay m. suryawanshi (BID ID -3381196)

DARSHAN ENTERPRISES (BID ID -3383235)

S.K.HARAL (BID ID -3381248)

VIRENDRA FABRICATORS (BID ID -3383605)

M/S.J.V.Datar (BID ID -3383597)