Loading
Loading…
Loading…
Tender Value
₹2.7 Cr
EMD Value
₹5.4 L
Closing Date
7 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SSE/DRG
17 conditions · 5 needing a document upload
Financial Eligibility Criteria:The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderers shall submit requisite information of contractual receipts as per Annexure- VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant with valid UDIN, duly supported by Audited Balance Sheet.
The tenderer shall possess a valid Electrical Contractor License, issued by any State Government or Union Territory Administration, authorizing execution of electrical works up to 11 kV. The contractor shall have in his employment or shall engage a person holding a valid certificate of competency issued by any State Government or Union Territory Administration for supervision of electrical works up to 11 kV. Offers not accompanied by a valid Electrical Contractor License and requisite Supervisor competency for works up to 11 kV shall be summarily rejected.
SIMILAR NATURE OF WORK: Works of wiring/cabling or installation and commissioning of electrical items (other than on coaches) such as lights, fans, pumps, charging arrangements, earthing etc. (with or without supply of items/equipments) for 230V, 1phase or 415V, 3phase system or higher voltages. A copy of similar nature of work should be uploaded through IREPS with their offer, failing which the tender will be rejected.
TECHNICAL ELIGIBILITY CRITERIA: The tenderer must have successfully completed or substantially completed any of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Note for Technical Eligibility criteria: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
58 conditions · 17 needing a document upload
IN CASE OF SINGLE PACKET TENDERS; CONSORTIUM AGREEMENTS, JOINT VENTURE FIRMS AND MOUS SHALL NOT BE CONSIDERED
IN CASE OF TWO PACKET TENDERS CONSORTIUM AGREEMENTS AND MOUS SHALL NOT BE CONSIDERED . BUT JOINT VENTURE FIRMS ARE CONSIDERED FOR ELIGIBILITY.
CONDITIONS FOR PARTICIPATION OF PROPRIETARY FIRM /PARTNERSHIP FIRM /PRIVATE LIMITED COMPANY / LIMITED COMPANY/ JV FIRMS:
In case the tenderer is an individual / proprietary concern, the experience and turnover shall be in the name and style of the Individual / Proprietary concern only.
In case the tenderer is a Partnership Firm, the experience and received contractual payments shall be in the name and style of the firm only. The other guidelines at Clause 18 of Part I of 3.1.1 IRSGCC shall be applicable . Note: The partner of a Partnership Firm cannot claim the credentials of Partnership firm to the extent of his share either during the subsistence of the Partnership firm or after its dissolution.
FOLLOWING DOCUMENTS SHALL BE ENCLOSED:
In case the Tenderer is a Partnership Firm: [i] Partnership deed . [ii]Power of Attorney (duly registered as per prevailing law) in favour of an individual to sign the tender documents and create 3.2.1 liability against the Firm. [iii] PAN / TAN number of Partnership firm (PAN / TAN number in the name of any of the constituent partners shall not be considered).
In case the Tenderer is a Company registered under Companies Act-2013:(i) the copies of MOA (Memorandum of Association) and AOA (Articles of Association) of the company; and (ii) A copy of Authorization/Power of Attorney issued by the Company 3.2.2 (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iii) copy of PAN number of the Company.
In case of JOINT VENTURE (JV) FIRMS: Clause No.17 of Part-I of IRSGCC with upto date correction slip shall be applicable in all aspects for Participation of Joint Venture[JV] firms in works tenders. JV firm should submit Memorandum of 3.2.3 Understanding[MOU] as per the format attached as annexure to the tender in DOCUMENTS. Submission of all other documents by JV firm / Members of JV should also be as per Cl.No.17.14 of Part-I of IRSGCC.
In case the Tenderer is a LLP Firm registered under LLP Act-2008 (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation; and (iii) a copy of Power of Attorney/Authorisation 3.2.4 issued by the LLP Firm in favour of the individual to sign the tender on behalf of the LLP Firm and create liability against the Firm. (iv) copy of PAN number of the LLP Firm
In case the Tenderer is a Registered Society & Registered Trust: (i) a copy of the Certificate of Registration, (ii) Deed of Formation; and (iii) a copy of Power of Attorney in favour of the 3.2.5 individual to sign the tender documents and create liability against the Society/Trust. (iv) copy of PAN number of the Society/Trust.
Uploading of other relevant documents connected to the tender;such as Declaration regarding employment of Retired Engineer/Retired Railway officer, NEFT Form, List of Personnel/Organization, List of Plant/machinery, Particulars of works on hand and completed (As per the formats attached in the list of Documents)etc.
The tenderer shall fill up proforma and sign and submit scanned (PDF) copy along with the offer. ( Click here to download Format)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The General Conditions of Contract governing the performance of the works covered by this tender are the Indian Railway Standard General Conditions of Contract as amended from time to time up to date. A soft copy of the Indian Railway Standard General conditions of Contract is uploaded in the annexed documents to the tender. Hard copy may be perused in the office of the Deputy C h i e f Electrical E n g i n e e r / S/ LGD,Secunderabad - 500025. In submitting his tender it would be deemed that the tenderer has kept himself fully Informed of the provision of the IRS General conditions of Contract including all corrections and Amendments issued up to date and claim that he is not aware of any amendment or correction slip to the IRS GCC shall not be entertained
The tenderer shall thoroughly go through the entire tender documents and strictly adhere the instructions and directions given at different pages.
Unreleased Bid security, if any, held with the Railway Administration, shall not be adjusted towards the Bid security to be remitted.
All terms and conditions in the tender documents are binding on the Tenderers
Railways reserves the right to accept or reject any or all the tenders and to award the work in whole or in part without assigning the reason for any such action.
The Tenderers are advised to visit the site of work in their own interest and acquaint themselves with the site conditions and expected quantum of work and assess all the site specific difficulties to be experienced while executing the same and the rate shall be arrived duly considering all the facts above and quoted in the tender. Any representation at a later date specifying the site difficulties shall not be consider.
Contractors are allowed to make payments against this tender towards Bid security in respect of e-tendering, shall be deposited either in cash through e payment gateway modes available ON IREPS portal LIKE net banking, debit card, credit card etc. or submitted as Bank Guarantee bond from a scheduled commercial bank of India. The Bank Guarantee bond shall be as per Annexure-VIA and shall be valid for a period of 90 days beyond the bid validity period. Manual payments through Demand draft, Banker cheque, Deposit receipts, FDR etc. are not allowed
In case the date of closing mentioned in the Notice Inviting Tender is declared a holiday/bandh/strike etc. on any account, the date of closing tender online will not be changed as the application in the website of IREPS does not permit submission of any offer after closing date and time of the tender. However, opening of tenders online will be on any convenient day after the closing date/time of tender
Should the Railway decide to negotiate with a view to bring down the rates, the tenderer called for negotiations should furnish the following form of declaration before commencement of the negotiations.
Railway Board vide their letter No. 2022/CE-I/CT/GCC-2022/Policy dated 27.04.2022 has issued Standard General Conditions of Contract (works contracts) is applicable to this contract.
CORRIGENDUM NOTICE ON IREPS: [I]Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
Applicable for the tenders with eligibility criteria: The offer of Tenderer(s) who do not enclose Experience Certificate & Turnover Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted /received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railway reserves the right to verify the authenticity of the documents/information furnished.
TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A of Part-II of IRSGCC and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works contract is decreased or any tax/cess on Works Contract is decreased /removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
Replacement of overaged Electrical assets & Rewiring works at S&T Workshop, Mettuguda
LGD-L-07-2026-27-OT
LGD-L-07-2026-27-OT
Open
Works - General
12 Months
Hyderabad, Telangana
₹0
₹5.4 L
7 Jul 2026
11 Jun 2026
23 Jun 2026
129 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 2,68,62,032 | ||
| — | 500.00 | — | — | ||
| Supply, erection, laying and commissioning of perforated GI cable tray, 100 mm (W) x 300 mm (D) x 2.5 mm thickness, made from 12 SWG galvanized iron, including all supporting fixtures, clamps, fasteners, and accessories, along with curve joints, L-bends, T-joints, cross joints, reducers, couplers, and all necessary hardware for a complete cable tray system, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 4,79,000 | |
| — | 2900.00 | — | — | ||
| Supply and laying of 4-core x 6 sq.mm, 1.1 kV PVC insulated and PVC sheathed cable with bare annealed copper conductor, as per IS 694:2010, including all required connecting accessories such as glands, lugs, ferrules, clamps, saddles, identification markers, and all incidental materials necessary for proper installation, termination, and commissioning, complete as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 14,35,500 | |
| — | 2450.00 | — | — | ||
| Supply and laying of 4-core x 4 sq.mm, 1.1 kV PVC insulated and PVC sheathed cable with bare annealed copper conductor, as per IS 694:2010, including all required connecting and termination accessories such as glands, lugs, ferrules, clamps, saddles, identification markers, and all incidental materials necessary for proper installation, testing, and commissioning, complete as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 9,33,450 | |
| — | 81000.00 | — | — | ||
| Supply of single core 1.5sq.mm multistranded FRLS copper wire for point wiring of lights and fans through SCH 80 PVC conduit pipes or PVC casing/capping as per site conditions, using Red (Phase), Black (Neutral), Green (Earth) color coding, including all bends, clamps, saddles, terminations, testing, and commissioning. Wires shall conform to IS 694 / IEC standards. | — | — | — | 20,25,000 | |
| — | 39000.00 | — | — | ||
| Supply, laying, and testing of single core 2.5sq.mm multistranded FRLS copper wire for circuit mains and 5-pin, 6A power sockets through SCH 80 PVC conduit pipes or PVC casing/capping as per site conditions, using Red (Phase), Black (Neutral), Green (Earth) color coding, including all bends, clamps, saddles, terminations, testing, and commissioning. Wires shall conform to IS 694 / IEC standards. | — | — | — | 18,72,000 | |
| — | 34300.00 | — | — | ||
| Supply, laying, and testing of single core 4sq.mm multistranded FRLSH industrial copper wire for 6A/16A/20A power sockets and power circuit mains through SCH 80 PVC conduit pipes or PVC casing/capping as per site conditions, using Red (Phase), Black (Neutral), Green (Earth) color coding, including all bends, clamps, saddles, terminations, testing, and commissioning. Wires shall conform to IS 694 / IEC standards. | — | — | — | 24,69,600 | |
| — | 29400.00 | — | — | ||
| Supply, laying, and testing of single core 6sq.mm multistranded FRLSH PVC insulated industrial copper cable for power sockets and power circuit mains through SCH 80 PVC conduit pipes or PVC casing/capping as per site conditions, using Red (Phase), Black (Neutral), Green (Earth) color coding, including all bends, clamps, saddles, terminations, testing, and commissioning. Wires shall conform to IS 694 / IEC standards. | — | — | — | 26,46,000 | |
| — | 3748.00 | — | — | ||
| Supply, laying and Testing of single core 10 sq.mm multistranded copper cable HRFR PVC type for power supply arrangement RYB (Red, Yellow and Blue colour and neutral Green) run through SCH 80 PVC conduit pipes/PVC casing capping as per the requirement of site condition. | — | — | — | 6,55,900 | |
| — | 245.00 | — | — | ||
| Supply of 8-way modular boxes with top plates, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 1,11,230 | |
| — | 245.00 | — | — | ||
| Supply, erection, testing, and commissioning of 20A double-pole MCB (B curve), including all connected accessories as per site conditions. | — | — | — | 1,65,865 | |
| — | 25.00 | — | — | ||
| Supply, erection, testing, and commissioning of 63A 4-pole MCB (B curve), including all connected accessories as per site conditions. | — | — | — | 78,725 | |
| — | 196.00 | — | — | ||
| Supply, erection, testing, and commissioning of 32A double-pole MCB (B curve), including all connected accessories as per site conditions. | — | — | — | 1,43,864 | |
| — | 392.00 | — | — | ||
| Supply, erection, testing, and commissioning of 6A single-pole MCB (B curve), including all connected accessories as per site conditions. | — | — | — | 71,736 | |
| — | 98.00 | — | — | ||
| SSupply, erection, testing, and commissioning of 16A single-pole MCB (B curve), including all connected accessories as per site conditions. | — | — | — | 20,776 | |
| — | 200.00 | — | — | ||
| Supply, erection, testing, and commissioning of 10A single-pole MCB (B curve), including all connected accessories as per site conditions | — | — | — | 36,600 | |
| — | 784.00 | — | — | ||
| Supply of 10A single-pole, 1-way modular switches, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with commissioning. | — | — | — | 37,632 | |
| — | 294.00 | — | — | ||
| Supply of 5-pin 6A/16A modular plug sockets with shutter type and 20A modular switches, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 1,98,450 | |
| — | 650.00 | — | — | ||
| Point wiring with single core 1.5sq.mm multistranded FRLS copper wire for lights and fans etc., through SCH 80 PVC conduit pipes or PVC casing/capping as per site conditions, including all connected accessories, bends, clamps, saddles, terminations, testing, and commissioning. Wires shall conform to IS 694 / IEC standards | — | — | — | 1,49,500 | |
| — | 400.00 | — | — | ||
| Wall cutting, chipping, erection, and laying of SCH 80 PVC conduit pipes, including plastering after laying, masonry works, and wherever not possible, laying PVC casing/capping as per site conditions, including all related hardware, accessories, clamps, bends, joints, and complete with testing and commissioning. | — | — | — | 43,200 | |
| — | 588.00 | — | — | ||
| Supply of PVC junction boxes (4-way, 3-way, 2-way, and single-way) with suitable top round plates as per site conditions, including all related hardware, accessories, clamps, screws, and complete with testing and commissioning. | — | — | — | 14,700 | |
| — | 550.00 | — | — | ||
| Supply of 3-pin ceiling roses with PVC round plates, including all required hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 13,750 | |
| — | 180.00 | — | — | ||
| Supply, erection, testing and commissioning of FOS LED High Bay Light, 50 W, with IP65 protection (dust-tight and water-jet resistant), suitable for harsh, dusty, and industrial workshop environments, having minimum 5000 lumens light output, complete with robust die-cast aluminium housing, integrated LED driver, mounting brackets / chains, connectors, wiring, and all associated hardware and accessories, including fixing, alignment, testing, and commissioning, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 5,58,000 | |
| — | 50.00 | — | — | ||
| Supply of 6 Feets /2 Meters Ceiling Fan Down Rod/Iron Rod 1.4mm thickness with all connected accessories | — | — | — | 20,550 | |
| — | 3000.00 | — | — | ||
| Supply of 20/25mm dia. SCH 80 PVC conduit pipes conforming to IS 9537 Part 3 or latest / PVC casing and capping BIS certified conforming to IS 14927 Part 2 or latest, as per site conditions, including all related hardware and accessories, bends, clamps, saddles, and terminations, complete with testing and commissioning. | — | — | — | 75,000 | |
| — | 800.00 | — | — | ||
| Supply of 32mm dia PVC conduit pipes / PVC casing and capping, including straight joints, L bends, T bends, and all related hardware and accessories as per site conditions, complete with bends, clamps, saddles, terminations, testing, and commissioning. | — | — | — | 31,200 | |
| — | 2.00 | — | — | ||
| Supply, erection, testing and commissioning of 500 kVA, 11 kV/0.433 kV, 3-phase, copper-wound, outdoor type energy-efficient distribution transformer (Level 3 or latest), complete with all required accessories including bushings, tap changer, terminals, earthing connections, mounting hardware, radiators, and other connected accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 25,62,544 | |
| — | 2.00 | — | — | ||
| Construction of pit for transformer plinths for outdoor transformers, size 1.5 m x 1.5 m x 1.5 m, including excavation, stone/brick masonry, plastering, and all connected accessories, complete in all respects as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 11,576 | |
| — | 1.00 | — | — | ||
| Dismantling and removal of existing 500 kVA transformer with all connected accessories, including disconnection, lifting, loading, transportation, unloading, and handing over to SSE/EM/S&T/MFT stores, as per site conditions and directions of the SSE/EM/S&T/MFT | — | — | — | 9,708 | |
| — | 3.00 | — | — | ||
| Dismantling and removing of existing 250 KVA transformer with all connected accessories and handing over to SSE/EM/S&T/MFT at his stores including loading unloading and transportation of the same as per the direction of the SSE/EM/S&T/MFT. | — | — | — | 29,124 | |
| — | 295.00 | — | — | ||
| Supply of 4-way modular boxes with top plates, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 19,470 | |
| — | 295.00 | — | — | ||
| Supply of 6-way modular boxes with top plates, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 36,875 | |
| — | 295.00 | — | — | ||
| Supply of 12-way modular boxes with top plates, including all connected hardware, screws, clamps, and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 58,705 | |
| — | 6.00 | — | — | ||
| Supply, erection, testing and commissioning of inverter-type split air-conditioning units, 1.5 TR capacity, 5-Star BEE rated, complete with indoor and outdoor units, insulated copper refrigerant piping, drain piping, interconnecting control and power cables, outdoor unit mounting brackets / stands, vibration pads, fasteners, and all associated hardware and accessories, including fixing, vacuuming, gas charging (if required), testing, and commissioning, as per site conditions and directions of the Engineer-in-Charge, complete in all respects. | — | — | — | 2,57,466 | |
| — | 50.00 | — | — | ||
| Supply, erection, and commissioning of 12 way SPN double door SDBs, including all connected accessories as per site conditions. | — | — | — | 98,700 | |
| — | 50.00 | — | — | ||
| Supply, erection, and commissioning of 8-way single-door SDBs, including all connected accessories as per site conditions. | — | — | — | 64,600 | |
| — | 35.00 | — | — | ||
| Supply, erection, and commissioning of 18-way single-door SDBs, including all connected accessories as per site conditions. | — | — | — | 73,815 | |
| — | 40.00 | — | — | ||
| Supply & fixing of 360° Slim PIR Ceiling mounted Occupancy (Presence) Sensor Similar to Legrand make as per the direction of Engineer at site | — | — | — | 1,43,600 | |
| — | 85.00 | — | — | ||
| Supply, erection, testing, and commissioning of 20W, 1200mm LED tube light fittings with LED lamps and inbuilt driver including all wiring connections and accessories as per site conditions, complete with testing and commissioning. | — | — | — | 49,470 | |
| — | 100.00 | — | — | ||
| Supply, erection, testing and commissioning of 1200 mm sweep energy-efficient BLDC ceiling fans, conforming to latest specifications No. SCR/CEE/SPC/BLDC.02/2022 or latest amendment, complete with BLDC motor, down rod, canopy, shackle assembly, remote control / regulator (wherever applicable), wiring connections, fixing clamps, fasteners, and all connected accessories, including mounting, alignment, testing, and commissioning, as per site requirements, drawings, and directions of the Engineer-in-Charge. | — | — | — | 2,75,600 | |
| — | 1.00 | Lumpsum | — | ||
| Dismantling and disconnecting of all connected accessories of existing over-aged electrical wiring, all types of electrical light fittings, fans, switches, sockets, MDBs, SDBs, and switchboards, from existing service buildings, workshop sheds, and SSE chambers at S&T Workshop, MFT area. Segregation of released materials and handing over to SSE/EM/S&T Workshop/MFT Stores, complete as per site conditions and directions of Engineer-in-Charge | — | — | — | 12,000 | |
| — | 1.00 | Lumpsum | — | ||
| Dismantling and disconnecting of all connected power supply accessories, including copper bus bars and associated hardware of existing over-aged LT panels in shop floor areas inside the S & T Workshop, with all released materials segregated and handed over to SSE/EM stores / MFT, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 18,000 | |
| — | 1.00 | Lumpsum | — | ||
| Releasing of HT underground cable, 3-core x 185 sq.mm aluminium, from transformers to HT VCB, including careful handling, pulling, laying in trench or route, and making it ready for termination, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 2,000 | |
| — | 1.00 | Lumpsum | — | ||
| Excavation of HT underground cable trench for 3-core x 185 sq.mm aluminium cable in the substation, from HT VCB to transformers, including excavation to required depth and width, removal of surplus soil, leveling, dressing of sides and bottom, and disposal of excavated material as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 4,000 | |
| — | 1.00 | Lumpsum | — | ||
| Releasing of existing LT underground cable from transformers to substation panels, including careful handling, pulling, laying in trench or route, and making it ready for termination, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 3,800 | |
| — | 125.00 | — | — | ||
| Supply, erection, laying, fixing, connecting and commissioning of 4 runs of 3-core x 185 sq.mm HT XLPE underground cable, 11 kV grade, as per IS 7098 (Part 2):1985 or latest, between 500 kVA transformer plinth to HT VCB, including cable glands, lugs, jointing, terminations, supports, trenches or ducts, and all required connected accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 1,21,875 | |
| — | 8.00 | — | — | ||
| Supply, fixing, connecting, testing and commissioning of 11 kV HT heat-shrinkable straight-through jointing kits, suitable for 3-core x 185 sq.mm XLPE HT cable, complete with all required accessories including aluminium crimping lugs, SS nuts & bolts, insulation materials, sealing compounds, and other connected accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 89,112 | |
| — | 630.00 | — | — | ||
| Excavation of cable trench in all types of soil for LT/HT cables, including excavation to required depth and width, removal of surplus soil, levelling and dressing of sides and bottom, and disposal of excavated material as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 84,420 | |
| — | 175.00 | — | — | ||
| Supply, erection, laying, connecting, testing and commissioning of 4 runs of 4-core x 400 sq.mm LT XLPE aluminium underground cable, 1.1 kV grade, as per IS 7098 (Part 1):1988 or latest, between new 500 kVA transformer plinth to substation MDB panel board, including suitable crimping lugs at both ends, terminations, supports, glands, ferrules, and all required connected accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 3,23,050 | |
| — | 580.00 | — | — | ||
| Supply, laying, erection, connecting, testing and commissioning of 4-core x 240 sq.mm LT XLPE aluminium underground cable, 1.1 kV grade, as per IS 7098 (Part 1):1988 or latest, including all required accessories such as crimping lugs, suitable nuts & bolts, glands, clamps, supports, and other connected hardware, as per site conditions and directions of the Engineer-in- Charge. | — | — | — | 7,37,180 | |
| — | 580.00 | — | — | ||
| Supply, laying, erection, connecting, testing and commissioning of 4-core x 120 sq.mm LT XLPE aluminium underground cable, 1.1 kV grade, as per IS 7098 (Part 1):1988 or latest, including all required accessories such as crimping lugs, suitable nuts & bolts, glands, clamps, supports, and other connected hardware, as per site conditions and directions of the Engineer-in- Charge. | — | — | — | 3,39,880 | |
| — | 190.00 | — | — | ||
| Supply, laying, erection, connecting, testing and commissioning of 4-core x 150 sq.mm LT XLPE aluminium underground cable, 1.1 kV grade, as per IS 7098 (Part 1):1988 or latest, including all required accessories such as crimping lugs, suitable nuts & bolts, glands, clamps, supports, and other connected hardware, as per site conditions and directions of the Engineer-in- Charge. | — | — | — | 2,32,940 | |
| — | 25.00 | — | — | ||
| Supply, erection, testing, and commissioning of earth pits, including all materials and construction as per IS 3043:1987 (or latest revision), comprising CI pipe electrode (100 mm ID, 13 mm wall thickness, 3000 mm length) painted with two coats of bitumen, fabrication, laying, and fixing of GI strips for earthing connections with all required bolts, nuts, double washers, clamps, and accessories to ensure proper electrical continuity. The excavated pit shall be backfilled with a mixture of charcoal/coke, salt, and sand (approx. 2.5 CMT of charcoal and salt) up to ground level. Provision of a brick masonry inspection chamber (650 mm x 650 mm x 1000 mm deep) with light- duty CI cover and frame, 12 mm cement plaster in 1:3 cement mortar on inside surfaces and exposed faces up to 300 mm below foundation, including curing, finishing, and making good. The item also includes all incidental materials such as CI pipe cover with frame, bricks, cement, sand, charcoal, salt, gravel, identification number plates, and any other items necessary for complete execution as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 2,16,525 | |
| — | 290.00 | — | — | ||
| Supply, erection, and connecting of 25 mm x 3 mm PVC insulated GI strip, including all required supporting hardware, clamps, saddles, fasteners, joints, bends, connectors, and accessories necessary for proper installation and continuity, complete in all respects as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 12,180 | |
| — | 32.00 | — | — | ||
| Supply, installation, testing and commissioning of 6 m single-arm hot-dip galvanized GI terminal pole complete with arm, having top dia 90 mm, bottom dia 155 mm, thickness 3.5 mm, base plate 260x260x12 mm, PCD 250 mm, M20x600 mm foundation bolts (4 Nos.), and access door 90x400 mm, including RCC concrete foundation with excavation, backfilling, curing, grouting, erection, alignment, earthing provision, and all connected hardware and accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 3,37,632 | |
| — | 32.00 | — | — | ||
| Supply, erection, testing and commissioning of 70 W outdoor LED street light fitting, with IP65 / IP66 protection (waterproof and dustproof), complete with LED driver, mounting brackets, wiring, connectors, fasteners, and all required connected accessories, including fixing, aiming, testing, and commissioning, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 2,35,776 | |
| — | 580.00 | — | — | ||
| Supply, laying, erection and testing of 4-core x 16 sq.mm LT XLPE underground cable, 1.1 kV grade, conforming to IS:7098 (Part-1):1988 or latest amendment, including excavation, sand bedding, protective covering, laying, jointing, termination with glands and lugs, backfilling and route marking, along with all connected accessories, complete in all respects, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 84,100 | |
| — | 190.00 | — | — | ||
| Supply, laying, connecting and erection of 3-core x 1.5 sq.mm multistranded FRLSH copper conductor, including connections to light fittings and 6 m pole junction boxes, complete with lugs, connectors, clips, saddles, and all required accessories, as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 6,650 | |
| — | 1.00 | — | — | ||
| Design, fabrication, supply of Cubicle-Type LT Main Distribution Board (MDB), IP65 weatherproof or above, fabricated from 14 SWG CRCA sheet steel with powder-coated or epoxy finish, comprising double bus bar arrangement of electrolytic copper for RYBN phases rated 1200 A, fully sectionalized. Switchgear: Microprocessor-based MCCBs (>125 A) conforming to IS 8623 / IS 2516 with lockable safety arrangements. Meters & Indications: Advanced bidirectional meters for each incoming/outgoing feeder, 0.2 S class CTs, RYB LED indicators, Ammeters, Voltmeters, PF meter, Frequency meter, selector switches, and digital 3-phase KWH meters with RS485 port. Incoming Feeders: 2 x 800 A ACBs, 1 x 600 A ACB with Auto Changeover Switch; Outgoing Feeders: 4 x 400 A TPN MCCBs, 3 x 320 A TPN MCCBs, 3 x 200 A TPN MCCBs, 3 x 165 A TPN MCCBs, 3 x 125 A TPN MCCBs, 4 x 63 A TPN C-Curve 10 kA MCBs, 4 x 40 A TPN C-Curve 10 kA MCBs, 3 x 32 A TPN C- Curve 10 kA MCBs. All MCCBs shall have ICs = 100% Icu² and be microprocessor-based. The MDB shall include all CTs, wiring, lugs, ferrules, cable entries, gland plates, name/danger plates, earthing, and shall be suitable for indoor installation, dust, moisture, and vermin resistant, fully compliant with IS 8623 / IS 2516 / IEC standards. Scope includes design, fabrication, supply, erection on suitable foundation/structure, testing, commissioning, and all connected accessories required for a complete and operational LT MDB installation as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 28,89,234 | |
| — | 1.00 | — | — | ||
| Design, fabrication, supply of LT Power Distribution Panel, double-door, outdoor type, weatherproof and waterproof, with suitable copper bus bars, microprocessor-based MCCBs with adjustable current settings, 3-phase RYB LED indications, and multifunction meters with RS485 port for incoming and outgoing feeders, comprising: Incoming: 1 x 400 A MCCB, 36 kA; Outgoing: 2 x 200 A TPN MCCBs, 35 kA; 3 x 125 A TPN MCCBs, 35 kA; 4 x 63 A TPN MCCBs, 35 kA. The panel shall include all cable entries, glands, lugs, ferrules, earthing, name/danger plates, and connected accessories, erected on masonry foundation/bed, tested and commissioned in accordance with IS standards and site conditions. All MCCBs shall be microprocessor-based with adjustable current settings, and the panel shall include 3-phase RYB LED indications and multifunction meters with RS485 communication port. Scope includes all accessories, cable glands, lugs, ferrules, earthing, name/danger plates, testing, and commissioning as per directions of the Engineer-in-Charge. | — | — | — | 7,00,339 | |
| — | 3.00 | — | — | ||
| Design, fabrication, supply of LT Double-Door Sheet Steel Distribution Board (SDB), floor / wall mounted as specified, fabricated from CRCA sheet steel with powder-coated finish, IP- rated enclosure, complete with microprocessor-based MCCB having adjustable current settings, suitable rated copper bus bars (phase, neutral & earth) with adequate supports and shrouding, and comprising the following switchgear: * RYB LED phase indication lamps * Multifunction energy meter with RS-485 communication port for monitoring of electrical parameters. Incoming: * 125 A, 4-Pole MCCB - 01 No. Outgoing: • 63 A, 4-Pole RCBO - 02 Nos. * 32 A, 4-Pole RCBO - 04 Nos. * 40 A, Double- Pole RCBO - 06 Nos. The panel shall include internal control wiring, cable terminations, glands, lugs, ferruling, earthing terminals, nameplates, danger labels, testing of protections, and commissioning, complete in all respects, in accordance with relevant IS / IEC standards and site requirements, to the satisfaction of the Engineer-in-Charge. | — | — | — | 7,69,866 | |
| — | 3.00 | — | — | ||
| Design, fabrication, supply of LT Double-Door Sheet Steel Sub Distribution Board (SDB), floor / wall mounted as specified, fabricated out of CRCA sheet steel with powder-coated finish and suitable IP rating, complete with microprocessor-based MCCB having adjustable current settings, and adequately rated copper bus bars (Phase, Neutral & Earth) with proper supports and shrouding, comprising the following switchgear and accessories: Accessories & Indications: * RYB LED phase indication lamps * Multifunction energy meter with RS-485 communication port for incoming and outgoing monitoring Incoming: * 150 A, 4-Pole MCCB - 01 No. Outgoing: * 63 A, 4-Pole MCCB - 03 Nos. * 40 A, 4-Pole RCBO - 04 Nos. * 32 A, 4-Pole RCBO - 04 Nos. * 32 A, Double-Pole RCBO - 04 Nos. The panel shall include internal wiring, control wiring, cable glands, lugs, ferruling, earthing terminals, danger and circuit identification labels, hardware, fasteners, complete in all respects, and shall be installed, tested, and commissioned as per relevant IS/IEC standards, approved drawings, and site conditions, to the satisfaction of the Engineer-in-Charge. | — | — | — | 12,07,233 | |
| — | 1.00 | — | — | ||
| Installation & Commissioning Charges for the LT Main Distribution Board (MDB)-Qty.1 Set, LT Double-Door Sheet Steel Sub Distribution Board (SDB) -Qty 3 Sets, LT Double-Door Sheet Steel Distribution Board (SDB)- Qty. 3 Sets, LT Power Distribution Panel- Qty.1 Set with all connected MCCBs, RCBOs, RS 485,bus bars, energy meters and all its connected accessories | — | — | — | 67,129 | |
| — | 50.00 | — | — | ||
| Supply, installation, testing and commissioning of 2 ft x 2 ft commercial LED recessed-mounted luminaires, 43 W, complete with all required drivers, connectors, wiring, fixing accessories, and mounting hardware, as per site conditions and drawings, including making good the surfaces after installation, to the satisfaction of the Engineer-in-Charge. | — | — | — | 69,850 | |
| — | 60.00 | — | — | ||
| Supply, erection, testing, and commissioning of 450 mm sweep energy-efficient BLDC wall-mounted fans, conforming to the latest applicable standards and specifications (e.g., IS 374: Part 2 or latest), including all mounting brackets, hardware, fasteners, electrical connections, and accessories required for proper installation and operation, complete as per site conditions and directions of the Engineer-in-Charge. | — | — | — | 3,18,780 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC2022 ACS11 merged
ATTACHMENT
Tender document
ATTACHMENT
GCC2022-ACS11merged_compressed_1.pdf
ATTACHMENT
TenderDocument-07-2026-27_2.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .