COMPLETE RENOVATION OF CSD DEPOT ADM BLOCK UNDER GE GUWAHATI

Amount

Dismantling plain or corrugated steel sheeting/galvalume sheet any guage, thickness including Nainital or similar pattern roof covering,complete all as specified and directed

Dismantling of boarding, any description and fixed in any position with nails complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floor), beams, staircase, landing, chhajjas and similar suspended work including removing rubbish off the premises complete all as specified and directed.

Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material complete all as specified and directed.

Taking down cement or cement lime plaster any description on any wall / ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down existing roof tretment of any size comlete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia complete all as specified and directed.

Demolition of cement concrete in roofs, floors (other than ground floor), beams, staircase, landing, chhajjas and similar suspended work including removing rubbish off the premises complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Supply and fix of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for weather boarding of 2nd class soft wood clean sawn, plain 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and directed.

Supply and fix of rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantry, rails, fastening, heavy bracket framing (Beam, tee, angle, channel or flat section), including distance pieces, cleats etc. confirming to Fe – 410 – S including cutting, welding etc. complete all as specified and directed.

Material and labour for preparation of steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer complete all as specified and directed

Material and labour for 25 mm thick Cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregates) in levelling coarse of floors surface even and fair using extra cement all as specified and directed.

Material and labour for 20 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

Material and labour for pavement floor vitrified tiles of sizes exeeding 0.09 sqm but not exceeding 0.36 sqm 10 mm thick ( endura tiles of Johnson or equivalent makes listed in list of makes) set & jointed in neat cement slurry and pointed with grey cement and pigment to match the colour of tiles in floor complete all as specified and directed.

Material and labour for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

Material and labour for 18-20 mm thick Pre polished machine cut Kota stone slab

(a) in single piece as in treads (including making 3 parallel grooves on kota stone Treads), including moulding/rounding the edges of the slab, over and including 15 mm thick backing layer in cement mortar (1:3) with cement slurry @3.00 kg/sqm laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and as directed.

(b) in single piece as in riser including moulding/rounding the edges of the slab, over and including 10 mm thick backing layer in cement mortar (1:3) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and as directed.

Material and labour for vitrified ceramic light shade coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile exc. 0.42 Sqm but not exc. 1.00 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

All as per item No.26.00 here-in-before but as in skirting complete all as specified and directed

Material and labour for 20 mm thick cement concrete pre-polished Chequered paver tiles 305x305x20mm thick, of approved design and approved colour set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of the tile as in floor complete all as specified and directed

Material and labour for rendering 10 mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado/skirting complete all as specified and directed.

Material and labour for glazed ceramic tiles as in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile complete all as specified and directed.

Material and labour for premium elevation / digital ceramic wall tiles as in vertical surface 300 x 600 x 7mm / 300 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile complete all as specified and directed.

Supply and fix 16-18 mm thick black granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like, set in over and including 15 mm thick cement screed in cement mortar 1:3 with cement slurry @3.0 kg/sqm and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling the old one complete all as specified and directed.

Material and labour for rounding to edges of stone slabs on edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Supply and fix hangers 6mm dia GI (upto 1200 mm length ) adjusting level fixed to roof slabs or steel framed structure or truss by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40mm long complete all as specified and directed

Supply and fix of anodised aluminium snap grid frame work for false ceiling complete all as specified and directed

Supply and fix Mineral Fiber acoustical suspended Ceiling system with Optra Microlook edge (600X600X15 mm) tiles with and including Silhoutte 15mm exposed grid complete all as specified and directed

Providing and fixing 12mm thick frameless toughened glass door shutter of providing and fixing hydraulic floor door closer (Dorma or equivalent) incl top & bottom pivot and making necessary holes and all hardware, decorative handle and patch lock etc. for door complete all as specified and directed

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-2 (using 40 mm graded stone aggregates) Cement concrete in foundations, filling and mass-concrete complete all as specified and directed.

Supply and fix Rolled mild steel Fe410 -W (Gde-E- 250) quality-A in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets etc. complete all as specified and directed.

Material and labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and labour for flat formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for RCC Type B1 1:1.5:3 (using 20 mm graded stone aggregates) in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs, shelves and the like complete all as specified and directed.

Material and labour for rendering 10 mm thick on faces of brick work or concrete surface in CM (1:6), finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 5 mm thick on fair faces of brick work or concrete surface in CM (1:3) as in ceiling, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:4) in two layers (10mm+5mm), top layer with liquid WPC as per manufacturer's instruction, finished even and fair complete all as specified and directed. NOTE : Water proofing compound shall be measured & paid separately

Supply only liquid water proofing compound complete all as specified and directed.

Material and labour for 2 mm thick wall care putty on newly plastered surfaces of wall for smooth finished surfaces complete all as specified and directed.

Material and labour for preparing new plastered surface. and applying two coats of plastic emulsion paint (interior emulsion) white or tinted over a coat of primer complete all as specified and directed.

Material and labour for preparation of newly plastered surface and applying two coats of exterior emulsion paint over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for preparation of old decorated wall surfaces by scrapping (any No of layers) rubbing down, washing etc as directed and apply a uniform layer of 2 mm thick wall care putty as approved after that the surface dry then apply two coats of plastic emulsion paint (interior emulsion) white or tinted over a coat of primer all as specified and directed."

Material and labour for preparation of old painted concrete /plastered wall surfaces including cleaning the surfaces by wire brushes and washing and appying one coat of acrylic antifungal exterior emulsion paint on walls over a coat of primer including errection of scaffolding complete all as specified and directed,

Material and labour for applying neat cement slurry over existing roof surface @ 3.0kg of cement per sq. metre complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-0 (using 10/12.5 mm graded stone aggregates) laid over roof slab after applying cement slurry as specified here-in-before under item No. 54.00 for filling undulations finsished even and fair without using extra cement complete all as specified and directed.

Material and labour for 15 mm thick rendering in CM (1:3) mixed with liquid water proofing compound as per manufacturers instructions over RCC roof slabs for laying water proofing treatment and surface finished even and fair complete all as specified and directed. Note : WPC will be measured and paid separately

Supply and fix APP polymeric water proofing membrane,minimum 3mm thick and weighing not less than 3.5 kg/sqm,black finish reinforced with non-woven polyster reinforcement matt with a thermo fusable finish laid over compatible cold emulsion bituminous primer applied at the rate of 0.40 kg/sqm by torching with a propane or a butane gas force with a overlap of 75 mm on a longitudinal direction and 100 mm on transverse direction including sealing all as per manufacturer's instruction complete all as specified and directed. Note : (i) Cover fillets in PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregates) of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of grade 30/40 conforming to IS-73,applied @1.2 kg/sqm over a coat of bituminous primer conforming to IS-3384 appled @0.40 kg/sqm (ii) Polymeric membrane shall be taken to a height of 45 cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing (iii) The water proofing treatment shall be got carried out by the manufacturer or their authorized applicators (iv) In case of stone masonry parapet wall etc a groove of size 25mm x 25mm (minimum) shall be made in cover fillet at the junction of roof and parapet wall / mumpty/ other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 100gms/sqm

Material and labour for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnections and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres all as specified and directed.

Supply and fix 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Material and labour for writing letter, figures, index arrows etc not exc 30 cm in height on PS / PVC Tank complete all as specified and directed.

Supply and fix in repair 20 mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

Material and labour for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregates) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished cement concrete surface even and smooth without using extra cement and providing joints throughout thickness of plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and two parts of sand by weight complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar 1:4 on concrete surfaces finished fair and even mixed with WPC as per manufacturer's instructions complete all as specified but excluding water proofing compound NOTE: Water proofing compound will be measured & paid separately.

Material and labour for treating sunken floor surfaces with two coats of chemical ( one priming coat and one subsiquent coat) as per manufacturer's instructions complete all as specified and directed.

Material and labour for cement concrete type E2, 1:5:10 (using 40mm graded stone aggregates) as in mass concrete in sunken floors complete all as specified and directed.

Material and labour for providing 25mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregates) as in flooring, and the like finished fair and even without using extra cement complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including cutting through walls together with all tube fittings (such as bends, elbows, tees, short pieces, connectors, backnuts,diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, complete all as specified and directed.

(a) Outer diameter of pipes :20mm

(b) Outer diameter of pipes :32 mm

Supply and fix coloured vitreous china half stall urinal with grating and union for discharge pipe including, waste pipe and PVC connection, bedding urinal against wall in cement mortar 1:2 securing urinal to wall all as per manufacturer instructions complete all as specified and directed.

Supply and fix curved shaped urinal partition with frosted glass 8mm/10mm thickness chrome finish fixing by cutting chase in wall and making good disturbed surfaces complete all as specified and directed.

Supply and fix vitreous china table top wash basin with granite counter area (including cutting for and pinning in ends for bracket,and waste fittings 32 mm including waste pipe, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

Supply and fixing in repair 15 mm bore Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

Supply and fix vitreous china squatting pan, orissa pattern size 580 X440 mm white/colour with integral foot rest (excluding flushing cistern and flush pipe) including provison of lime concrete complete all as specified and directed.

Supply and fix PVC valveless, syphonic action type, wall hung 10 litres flushing cistern, low level, white with inlet ball valve foat and handle including brackets complete all as specified and directed.

Supply and fix rimless single piece water closet WC, white, china ware wash down water closet pan with and including vitreous china flushigng cistern, plastic water closet seat white closed pattern with flat bottom and cover including fixing the same as per manufacturer instruction, jointing the water pipe etc by making hole in stone masonry wall and making good disturbed portion etc complete all as specified and directed.

Supply and fixing in repair 15mm bore brass chromium plated fancy type bib cock with wall flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fixing in repair Hand Shower (Health Faucet) with 58mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed.

Supply and fixing in repair chromium plated toilet paper holder with cover complete all as specified and directed.

Supply and fixing in repair 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing in repair sink made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or fixing on kitchen platform and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including CP 32/40 mm dia waste coupling and waste pipe complete all as specified and directed.

Supply and fix in repair 15 mm bore CP sink cock with regular swinging spout (wall mounted) with wall flange screwed down for iron pipe and fixed complete all as specified and directed. (Minimum weight 15mm-1200 gms)

Supply and fix 125mm dia PTMT grating doom with waste hole for waste pipe (minimum weight 40 gram) complete all as specified and directed.

Supply and fix in repair 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall with stack clamp complete all as specified and directed.

Supply and fix in repair of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix in repair of 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

Supply and fix in repair of 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

Supply and fix in PVC (SWR) floor trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Material and labour for 18 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and around covered with 6 mm thick teak wood beading/lipping fixed to timber frame work including dismantling old boarding complete all as specified and directed.

Supply and fix 25 mm thick second class hardwood boarding plane both side fixed in shelves; Partitions and shelves of built-in cupboards, almirahs, book cases,toilet boxes, racks, pelmets and similar work complete all as specified and directed.

Supply and fix 75mm hasp and staple mild steel wire type, stove enamelled black including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fix 30 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

Providing and fixing factory made uPVC white colour two track sliding window frame (60mm X 62mm ), made of extruded profiles. Profiles of frames and sash will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware, EPDM gasket, 1.2+0.2 mm thick galvanized steel profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, all complete and as directed, Note: (i) Glazing, hardware hinges and fitting, EPDM rubber gasket etc. to be paid separately. (ii) Each member of window to be measured separately with clear length.

Supply and fix 5mm thick tinted glass, ordinary quality and glazing in uPVC windows in square/rectangle n.exc 0.5 sqm in each complete all as specified and directed.

Supply and fix PVC honeycomb window venetian blind mounted outside using necessary brackets and screws complete all as specified and directed

Supply and fixing of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply and fixing of Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded prelam colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the M.S frame welded/sealed to the stiles, & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Material and labour for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and fix 30mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and both faces is covered with decorative face veneer with lipping/frame to match etc complete and size of member of shutters as specified in SSR Part-I (2009) section 8 complete all as specified and directed.

Supply and fix of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

Supply and fix of 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Supply and fix of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed.

Supply and fix of 150 mm long extruded brass handles, fabricated type polished complete all as specified and directed.

Supply and fix of 150 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

Supply and fix of 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

Supply and fix aluminum (extruded section) door closer hydraulically regulated designation No-1 universal type suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

Material and labour for preparation of new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing ,louvers for ventilators and powder coated (minimum thickness of powder coating 50 micron)etc. complete all as specified and directed

Material and labour for anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading, screws and powder coated (minimum thickness of powder coating 50 micron) etc. complete all as specified and directed

Material and labour for 6mm thick sheet glass, ordinary quality and glazing fixed in aluminium frames in square/rectangle exc 0.5 sq. m in each pane complete all as specified and directed

Material and labour for 3 mm thick figured glass, ordinary quality and glazing fixed in louvers frames in square/rectangle n exc 0.5 sq. m in each pane complete all as specified and directed

Material and labour for 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to aluminium frame work complete all as specified and directed

Material and labour for 100 mm aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply and fix of 75 mm aluminium 4 lever vertical type mortice lock complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified and directed..

Material and labour for cement concrete in foundation filling and mass concrete type C2, 1:3:6 (using 40 mm graded stone aggregates) complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 as in wall of drain all as specified and directed.

Material and labour for rendering 15 mm thick in cement mortar (1:4) & finished the surface even & fair without using extra cement complete all as specified and directed.

Material and labour for PCC type B1 1:2:4 (using 20mm graded stone aggregates) as in coping on brick work including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-2 (using 40mm graded stone aggregates) as in benching or surface channel all as specified and directed.

Material and labour for precast RCC manhole cover slab 1:2:4 type B-1 (using 20mm graded stone aggregates) set in CM 1:4 of thickness complete all as specified and directed.

Material and labour for TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed.

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Taking down carefully copper / Aluminium point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls, roofs etc all as specified and directed.

Taking down carefully unservicable main switch and DB's including MCBs of any size make, type and capacity and depositing at site as specified and directed.

Material and labour for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLSH cable 1100 volts grade drawn through and including non metallic rigid PVC Concealed conduit,medium grade minimum 20 mm dia ISI marked and conduit accessories fixed on recesses of wall/ceiling/roof etc with sunken type pressed steel/welded MS terminal boxes made out of 1.2 mm MS sheet, 3mm thick Modular top cover for mounting of modular fittings,switches,sockets outlets,regulators etc complete including provisining of 1.5 sqmm PVC insulated unsheathed FRLSH cable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly for the following :- Note: Cutting chases and making good shall be measured & paid separately under relevant item.

One light/Fan point controlled by one, one way switch.

One light point controlled by two 2 way switches.

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size

One 3 pin 5 Amps socket outlet on same board with other switch.

One 3 pin 5 Amps socket outlet on independent board with cable of 1.5 sqmm size.

All as per item No.128.00 here-in- above but wiring with 4 sqmm multistranded copper conductor unsheathed and 4 sqmm copper conductor unsheathed cable as earth continuity conductor for one 3 pin 15 Amps socket outlet point on independent board complete all as specified and directed.

Material and labour for Concealed sub main wiring using two single core 10 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade (FRLSH) ISI marked drawing in and including 20mm dia rigid non metalic PVC conduit & accessories like bends, tee, etc fixed on recess of wall and ceiling and connecting to earth dolly and including 6 Sqmm earth wire, PVC insulated & unsheathed complete all as specified and directed. NOTE: (i) 2 runs of 10 Sqmm wire + 1 run of 6 Sqmm earth wire + 1 run of PVC conduit with accessories shall be measured as one unit. (ii) Cutting chases and making good shall be measured & paid separately under relevant item.

Material and labour for Concealed sub main wiring using two single core 6 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade (FRLSH) ISI marked drawing in and including 20mm dia rigid non metalic PVC conduit & accessories like bends, tee, etc fixed on recess of wall and ceiling and connecting to earth dolly and including 6 Sqmm earth wire, PVC insulated & unsheathed complete. NOTE: (i) 2 runs of 6 Sqmm wire + 1 run of 6 Sqmm earth wire + 1 run of PVC conduit with accessories shall be measured as one unit. (ii) Cutting chases and making good shall be measured & paid separately under relevant item.

Supply and fixing LED Tubelight lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED tubelight fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix 10W LED Bulkhead light,pressure die cast housing LED bulkhead with IP65 Protection and IK09 Impact resistance suitable for surface/wall mounted,complete with all accessories pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm,36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for false ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders ,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing Call bell, Ding Dong AC. 230 volts,single pole complete all as specified and directed.

Supply and fixing Modular switch one way 5/6 Amp ,1 module,240 Volts complete all as specified and directed.

Supply and fixing Modular switch two way 5/6 Amp,1 module, 240 Volts complete all as specified and directed.

Supply and fixing Modular Bell push 6 Amp,1 module, 240 Volts complete all as specified and directed.

Supply and fixing Modular socket 2/3 pin, 6 Amps,2 module 240 Volts complete all as specified and directed.

Supply and fixing Modular switch one way, 16 Amp,1 module, 240 Volts complete all as specified and directed.

Supply and fixing Modular socket 16A, 6 pin, 3 module 240 volts complete all as specified and directed.

Supply and fixing ceiling rose surface bakelite two to three terminal 65 x 50 mm three terminal 250/230 volts ISI marked complete all as specified and directed.

Supply and fixing fan step regulator,120W,2 Module A/C 240 Volts complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Supply and fixing Factory made distribution board in sheet steel enclosure VTPN DB 4 WAY double door glazed with 200 Amps rated bus bar,, 415 Volts suitable for housing MCCBs as incomer and MCB as outgoing. Complete including sinking of DB on wall and making surface good.complete all as specified and as directed.

Supply and fixing Factory made distribution board in sheet steel enclosure double door glazed with 200 Amps rated bus bar, SPN, 12 ways, 240 Volts suitable for housing MCBs.complete all as specified and as directed.

Supply and fixing MCCB 125 Amps, 415 volts, 4 pole , 16 KA complete all as specified and as directed.

Supply and fixing MCB, TPN, 415 volts, B Curve , 63 Amps, 10 KA,4P complete all as specified and as directed.

Supply and fixing MCB, SPN, 240 volts, C Curve , 63 Amps 10 KA complete all as specified and as directed.

Supply and fixing MCB, SP, 240 volts, 20-32 Amps 10 KA ,C Curve, complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES Part I all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note:- Rate quoted by tenderers shall be deemed to include for following provisions-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 m. [ii].PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m complete all as specified and as directed.

Supply and fixing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hexagonal head screw complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Material and labour for 32 mm bore light grade GI pipe fixed as bracket, on wall any type, not less than 1.5 m long and bent to shape as required complete with sutiable clamp made out of 25x4mm Flat iron duly fixed 12mm dia nuts, bolts, washers etc. complete all as specified and directed.

Supply and fixing power unit with 20A MCB & Plug 240 volts complete for ACs & Geyser complete all as specified and directed.

Supply and fixing Motor Starter 25A 240 volts complete for ACs & Geyser complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louver complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed.

Supply and fixing of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95 sq.mm, 3.5 core complete all as specified and directed.

M/s JK Jangid and Company