SPECIAL REPAIRS AND STRUCTURAL REHABILITATION OF RCC SEPTIC TANKS NEAR P-34,P-27,P-90 AND P-80 AND PROVN OF DEFICIENT STORE ROOM FOR MES OFFICE AND PROVN OF TOILETS AT INS HAMLA UNDER GE(NW) BHANDUP

Amount

Surface exvcavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas n.exc 1.5m deep and getting out in hard / dense soil complete all as specifed and directed.

Excavation over areas exc 1.5m deep but n exc 3.00 m deep and getting out in hard / dense soil complete all as specifed and directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation, sewage line or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10sqm on plan and not exc. 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface in hard / dense soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25 cm in ant type of soil complete all as specifed and directed.

Removing excavated materials not exc 50m and depositing where directed at a level not exc 1.5m above the strating point complete all as specifed and directed.

M & L for Hard Core of broken stone guage not exceeding 63mm deposited, spread levelled in layers not exceeding 15 cm thick watered and rolled/rammed to a true surface using stone boulders of trap stone, all as specified .

M & L for Hardcore of broken stone guage exc 63mm but n.exc 100mm deposited spread and levelled in layers n exc 15cm thick, watered and rolled/rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L for sand filling under floor or in foundations including watering and cosolidation complete all as specified and directed.

M & L for RCC M 25 Design mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specifed and directed.

M&L RCC M-30 using 20 mm graded aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specifed and directed.

M&L RCC M-30 using 20 mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specifed and directed.

M&L RCC M-30 using 20 mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specifed and directed.

M&L RCC M-30 Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specifed and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in columns, pillars, piers, posts, struts and the likein foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified and directed.

M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed/broken stone aggregate as in foundation, filling and mass concrete, all as specified .

M&L for cement concrete type C-2 , 1 : 3 : 6 (using 40mm graded stone aggregate) in foundation and filling concrete for columns, fencing posts etc complete all as specified and directed.

M&L PCC 1:2:4 type B2 using 40mm graded crushed stone aggregates as in mass concrete in foundation concrete, sides and making fair round/ chamfering the edge all as specified and directed by Engr-in-Charge

M & L for Use and waste of form work to sides or faces of concrete walls, retaining walls, abutments, parapets and similar work uncluding attached pillasters for flat and rough surfaces complete all as specifed and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specifed and directed.

M&L Formwork to rough finished surfaces of sides and soffits of floor/plinth or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specifed and directed.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide ® complete all as specifed and directed.

M&L Formwork to rough finished surfaces of sides pillars, posts, struts, piers, columns, and stanchions etc. complete all as specifed and directed.

M & L for use and waste of form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

M & L TMT bars 10mm dia and over cut to length, bent to shape reqd, inculding cranking,bending spirally for hooping for Columns, hooking ends and binding with and incl MS wire(annealed) not less than .90mm dia complete all as specified and directed.

M & L TMT bars 6 to 8 mm dia, cut to length, bent to shape required inculding cranking,bending spirally for hooping for Columns, hooking ends and binding with and incl MS wire(annealed) not less than .90mm dia complete all as specified and directed.

All as per item above but TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specifed and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conformin g to I. S.1161- 1979 grade St.-240 complete all as specifed and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, post or flat sections) including distance pieces, cleats etc. Fe-410- W(Gde-E-250) quality-B including distance pieces, cleats plate etc incl required welding as per relevent IS complete all as specified and directed.

S& F Mild steel angle iron cut to shape as directed drilling holes notching for wire as in posts and struts in fencing etc including all necessary cutting and welding etc and for similar work complete all as specified and directed.

S&F for mild steel screw bolts (machine cut) with hexagonal or square heads at one end and srewed the other or screwed both ends each screwed end to be fitted wth washers and one hexagonal or square nut, not exceeding 5 cm long and diameter of neck 5 to 10mm complete all as specifed and directed.

S&F rolled mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and countersunk) forming holes, without any attachment, Fe 410-W (Gde-E-250) quality-B, complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided rainforced (rainforcement of cut as required to facilasite demolition etc) including removal of demolished materials out side of MD land complete all as specifed and directed.

Demolition and breaking up 150mm drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar including bed concrete and removal of debris including sludge if any and side MD land complete all as specifed and directed.

M&L salt glazed stone ware drain pipes of 150 mm internal dia laid in trenches and jointed in complete all as specifed and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes 150mm dia including packing under and haunching against the sides of pipes after they are laid and tested complete all as specifed and directed.

Demolition and breaking up 200mm drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar including bed concrete and removal of debris including sludge if any and side MD land complete all as specifed and directed.

M&L salt glazed stone ware drain pipes of 200 mm internal dia laid in trenches and jointed complete all as specifed and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in bed to drain pipes 200mm dia including packing under and haunching against the sides of pipes after they are laid and tested complete all as specifed and directed.

Cutting to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specifed and directed.

Cutting to existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for internal dia of pipe 200mm complete all as specifed and directed.

Demolition of brick work built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc.6 mtr radius built in cement mortar (1:6) complete all as specifed and directed.

M&L brickwork with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specifed and directed.

M & L for 10mm thick rendering in Cm 1:4 using WPC @ 2% by weight of cement on brick work or concrete surfaces; surfaces finished even and smooth with out using extra cement complete all as specified Note : Water proofing compound shall be measured & paid seperately.

M&L for rendering cement plaster, 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and directed.

M & L for rendering 20mm thick in (1:4) cm (in two coats (15+5mm) with both coats mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. ( Note : WPC will be measured separately).

M & L for rendering 15mm thick in (1:6) CM on fair faces of brick work or concrete surfaces of walls and finishing even and smooth without using extra cement complete all as specified and directed.

Supply only polymer based liquid water proofing compound complete all as specified and directed.

M&L for rendering cement plaster 5 mm thick in cement mortar 1:3 on fair faces of concrete in ceiling, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound.

M & L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B-2, (using 40 mm graded stone aggregate) as in floors and pavings etc finished rough surface complete all as specified and directed.

M&L 75 mm thick plain cement concrete 1:4:8 type D-2 ( using 20 mm graded stone aggregate) as in sub base, floors etc complete all as specifed and directed.

M&L 25 mm thick plain cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in floors finished even and fair,complete all as specifed and directed.

M&L 75mm thick cement concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection & paving, finished even & smooth without using extra cement complete all as specifed and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws complete all as specified and directed.

M&L PVC coated chain link fencing, size n exc 40mm x 40mm The dia of GI wire shall be 2.5mm to 3mm and thickness of PVC shall be 1mm to 1.5mm fixed to the posts complete all as specified and directed.

M& L for Preparation of new or previously untreated surface and applying two coats of synthetic enamel paint over a coat of red oxide on steel surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of new painted surface of ceiling and applying three coats of white wash complete all as specifed and directed.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash complete all as specifed and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV esistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. ® complete all as specifed and directed.

S&F extruded Powder coated aluminium section as in Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and all directed

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as specifed and directed.

S & F Factory made solid panel PVC moulded door shutter with particle board core 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face and 2 mm thick plain color PVC sheet on back face supply and fixing in frame at site as per specification and drawing complete all as specified and directed

S&F Extruded Aluminium anodised, barrel tower bolts of extruded section 100mm long complete all as specifed and directed.

S&F Aluminium alloy handles, fabricated type, anodised 75mm size complete all as specifed and directed.

S&F butt hinges medium weight 100 mm size complete all as specifed and directed.

M &L Aluminium alloy, anodised sliding door bolt,300mm long with hasp & staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy complete all as specifed and directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

M&L non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 10 mm thick in CM 1 : 6 complete all as specified and directed.

M&L Glazed colored ceramic colored tiles on vertical surfaces 300 x 450 x 7 mm thick such as skirting, dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match pattern and shade including 10 thick rendering in CM 1:4 on faces of brick/concrete work finished rough to receive tiles complete all as specified and directed.

S&F 60 mm machine pressed precast concrete interlocking paver blocks with white cement and color pigment, any shape and size conforming to IS 15658:2006 complete all as specified and directed.

S&F in repair Low density PVC connection commercial quality 450mm long including PTMT nuts at both sides of 15mm bore and fixed complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size 465 x 355 x 265mm, wgite, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) incl Low density PVC waste pipe 40mm bore, 600mm long complete all as specified and directed.

M&L 15mm bore steel tubing, medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm bore steel tubing, medium grade, galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest including trap, PVC flushing pipe and anti-syphonage pipe including PVC valveless, syphonic action, flushing cistern 10 ltr capacity, low level, white, with inlet ball valve, float and handle including brackets, UPVC traps 'P' or 'S' of 110mm dia. complete all as specified and directed.

S&F vitreous china wash basin (Padestal pattern), white, flat back, size 600 x 480 mm, including PVC LDPE pipe 600 mm long, chain & plug and porcelain stopper but including brackets, 32 mm bore waste coupling,wastpipe 15 mm dia fancy type CP pillar taps complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate size 160x160x90mm complete all as specified and directed.

S&F 15mm bore bib tap long nose/long body cast copper alloy CP fancy type with capstan head handle,screwed down, screwed for brass, weight n ot less than 450 gms ferrule and fixed complete all as specified and directed.

S & F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specifed and directed.

S&F 15mm bore stop/angle cock, cast copper alloy CP, fency type high presure with capstan head handle,wt n less than 450 gms screwed both ends for iron pipe of for unions complete all as specified and directed.

S&F 110mm UPVC, SWR pipes, single socketed in any length with rubber rign joint fixed with wall complete all as specified and directed

All as per item above but 75mm bore pipe complete all as specified and directed

S&F UPVC bends (any radius) of 110mm dia complete all as specified .

S&F UPVC bends (any radius) of 75mm dia complete all as specified .

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F PTMT grating doom with or without waste hole 75 mm dia.(Min.weight 25gms).complete all as specified and directed.

S&F Brass CP towel rail 20mm dia `D' type 60 cm long between flanges complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank (multilayer quality) cylindrical vertical with closed top of capacity 500 litres, hoisted and fixed in position with connecting ports (inlet, outlet and over flows) including 25 mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete, all as specified and as directed.

Deduct Credit for Demolished/ Dismantled material Rs. (-) 60575.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

Vishal Builders

M/S VISHRANTA CONSTRUCTION

M/s Mukesh Engineers