SPECIAL REPAIR TO PERIMETER SECURITY WALL BETWEEN MAIN GATE AND DELTA 18 AT AFA, HYDERABAD

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Demolition of Brick/stone masonry built in cement mortar of any description, etc complete all as specified and as directed

Dismantling existing barbed wire/plain wire/ chain link fencing any type from RCC/Steel/Wdn posts complete etc all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for RCC Chajjas/Roof projections etc complete all as specified and as directed. (Reinforcement cut as required to facilitate demolition)

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for foundation,Plinth protection, filling and mass concrete complete and including removing rubbish off the permises complete all as directed.

Removal of debris (aggreates of any description) obtained from demolition including loading and unloading to a distance not less than 5 KM from the starting piont and deposited where directed etc, complete all as specified and as directed.

Excavating over areas, not exceeding 1.50 m deep and getting out in soft / loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick of excavated soil complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

M & L cement concrete in foundation, filling and mass concrete type D-2, 1:4:8 mix using 40 mm graded stone aggregate, completed all as specified and directed.

Formwork to sides of concrete foundations, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical ot to batter, of rough finished flat surface of concrete, complete all as specified and directed.

M & L Providing Reinforced cement (Design mix M-30) ( using 20 mm graded stone aggregate ), as in foundation Beams,plinth beams,bases for columns, etc, basement slabs, under-reamed piles and mass concrete and similar works etc completed all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical ot to batter, of rough finished flat surface of concrete, complete all as specified and directed.

M & L Providing Reinforced cement concrete (Design mix M-30), in type B1, 1:2:4 mix ( using 20 mm graded stone aggregate ) and as in walls, retaining walls, basement walls, ballast wall, and the like, any thickness, above top of, completed all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions and similar work, of rough finished surface (Square, rectangular or polygonal) of concrete, complete all as specified and directed.

M & L Providing Reinforced cement concrete (Design mix M-30) ( using 20 mm graded stone aggregate ) and as in Columns, pillars, piers, posts and struts, completed all as specified and directed.

Formwork to sides and soffits of floors or roof beams, beam haunchings, gerders, bressummers, lintels, cantilevers, shalves including supports etc. and similar work, of rough finished flat surface of concrete, complete all as specified and directed.

M & L Providing Reinforced cement concrete (Design mix M-30) ( using 20 mm graded stone aggregate ) and as in Beams, cantilevers, bressummers, lintels over 1.50m span, completed all as specified and directed.

M & L for reinforced cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in copings, benching, Kerb, etc all as directed by Engr-in-Charge

M&L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90 mm dia complete all as specified and as directed.

S&F mild steel TMT bar 6 mm to 8 mm dia. and over, cut to length , bent to shape as required, hooking ends and bining with and including mild steel wire (annealed) not less than 0.9 mm dia. Used in stirrups, spacers and binders, complete all as specified and directed.

M&L for pre-cast cement concrete block masonry of type B1 1:2:4 (using 20mm graded stone aggregate) with solid blocks exc 10cm in width and setting in cement mortar 1:4 etc complete all as specified and as directed.

S&F PVC (SWR) pipes 110 mm bore single socketted in any length with rubber ring joints laid in trenches or floors etc complete all as specified and as directed

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:4, including finished even and smooth without using extra cement, complete all as specified and directed.

S&F Framed brackets of angles or tee with web and flanges cut to shape ,drilled and countersunk for screw , incuding bending and welding angles, as necessary gusset plates ,rivetting , etc. not exc. 10 Kg each brackets, conforming to Fe-290 Gde E-165, complete all as specified and directed.

M&L Concertina coil super barb - bladed profile of dia 610 mm of weight not less dan 8.50 kgs per coil of 7.5m of length fixed to angle iron brackets or masonry surfaces with necessary accessories like straining wires, fixing clips etc complete all as specified and as directed. Note :- Concertina coil shall be measured linearly of fencing length. The number of spirals shall not be less than 51 in 7.5 m length of each coil.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, ladders, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

M & L Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary tint ) over a coat of red oxide, zinc chrome, complete all as specified and directed.

M & L for two coats of cement base paint on new plastered surfaces on wall over a coat of cement primer including preparation of surfaces, completed all as specified and directed.

M&L Loose filling of Broken stone or aggregates of gauge 40 to 80mm size as in filter media complete all as specified and shown on drg.

M&L Broken glass coping on top of compound walls in Cement mortar 1:3 complete all as specified and as directed.

S J REDDY

M/s Amit Associates

M/s RAMA LAKSHMI CONSTRUCTIONS