Short Term Maintenance Work 2025-2026 for Indapur - Wadpale ( NH No-66) from km 87.100 to km 91.600 and 99.600 to 110.750 and Short term Maintenance work 2025-26 for Maintenance of Savitri Bridge at 131.351 (RHS side) and Jagbudi Bridge 178.200 (LH

Trimming of grass, shurbs and weeds from the shoulders/berms and disposing off the same to suitable locations etc. complete (Item No. 8.17)

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete(Material obtained from Other sources) (Item No. 2.28)

Providing and laying filter material underneath pitching in slopes as per drawings and technical specifications etc. complete. (Item No. 14.74)

Providing dry rubble stone pitching 23cm(about 9) thick including all material, quarry spalls, labour etc. complete. (Item No. 2.34)

The maintenance of drains include erosion, repair, clearing, cleaning, reshaping, regrading, deepening of side drains as well as catch water drains etc. complete (Item No. 8.12)

Manualy clearing the chockes from under ground drainage line including Inspection chambers with the help of required tools for propre functioning line chamber to chamber etc. complete. (Item No. 46.54)

Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing etc. complete (Item No. 8.13)

Painting with synthetic enamel paint two coats to give an even and smooth surface for protection of exposed concrete/machinery portion of Bridge/CD works/parapet, kerb painting complete as per approval of Engineer. (Old existing surface). SDB Item No.14.16.B

Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking cement concrete paving blocks 80MM thick in M-40 grade of approved size and shape for City streets, small/medium market roads, low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658:2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of natural sand/crushed sand of 50mm thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete. (Item No. 5.20)

Repair to pot holes by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method filled with 75mm B.M, applying bitumen tack coat at the bottom and vertical sides as per as per MORTH specification clause 3004.1 and 3004.2 (Item No. 8.06)

Dismantling of cement concrete pavement by mechanical means using pneumatic tools, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately etc. complete. (Item No. 3.11)

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25mm, , cement content not to be less than 150kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor/by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.13)

Providing and laying 125 micron Low Density Polyethylene(LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete. (Item No. 5.19)

Providing and laying in-situ M40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate(natural sand/VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver, compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound/by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant(Pan mixer) etc. complete. (Item No. 5.03)

Providing and fixing in position TMT FE 500, 32mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60cms. Long and at 30.00cm. C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete. (Item No. 5.14)

Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12mm dia. 70cms.long and at 30.00cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening, supported by assembly of TMT FE 500, chairs with proper alignment etc. complete. (Item No. 5.16)

Cutting transverse contraction joints 3 to 4mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay/slab etc. complete including subsequent widening of the groove 8 to 10mm. wide at top having depth of 15mm. as directed by Engineer incharge. (Item No. 5.17)

Providing to contraction joints polysuphide sealent(Pouring grade) confirming to BS : 5212-1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter(appraox. 25% larger than the initial 3mm.to 4mm. joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet/air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer.(A) Contraction and longitudinal joints(15mm. deep x 8mm.wide) (Item No. 5.18)

Maintenance of road signs by way of cleaning and repainting of mandatory/requlatory/cautionary/informatory and place identifications sign board as per drawings etc. complete (Item No. 8.14)

Maintenance of Kilometer stones, and 200 metre by way of refiting of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200 metre km stone and 5th km stone etc. complete (Item No. 8.15)

Providing and fixing RCC 200 meter stones as per I.R.C. standard including fixing in standard size CC 1:4:8 block including curing, painting lettering etc. complete. (Item No. 6.02a)

Providing and fixing 1:2:4 ordinary km. stones as per I.R.C. standard including fixing in standard size C.C. 1:4:8 block including curing, painting lettering etc. complete. (Item No. 6.02b)

Providing and fixing R.C.C. 5th Km. stones as per I.R.C. standard including fixing in standard size C.C. 1:4:8 block including curing, painting lettering etc. complete. (Item No. 6.02c)

Metal Beam Crash Barrier -- Type-A, W : Metal Beam Crash Barrier(Providing and erecting a W metal beam crash barrier comprising of 3mm thick corrugated sheet metal beam rail, 70cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5mm spaced 2m centre to centre, 1.8m high, 1.1m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5mm, 330mm long complete as per clause 810)" (Item No. 7.30)

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 900mm made out of 2mm aluminum sheet bonded with white retro reflective sheeting of Class C(Type XI Micro prismatic grade sheeting) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65mm X 65mm X 6mm, 3.45m long, duly painted with with flat oil paint having alternate black and white bands of 25cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. ClassC(Type XI Micro prismatic grade sheeting) shall have 10 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.30e)

Providing and fixing of retro-reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 square metre made out of 4mm aluminum composite material sheet bonded with white retro reflective sheeting of Class B(Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75mm x 75mm x 6mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B(Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.33b)

Providing and fixing Mandatory/Regulatory sign boards in circular shape of 900mm dia made out of 2mm aluminum sheet bonded with white retro reflective sheeting of Class C(Type XI Micro prismatic grade sheeting) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65mm X 65mm X 6mm, 3.45m long, duly painted with with flat oil paint having alternate black and white bands of 25cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X

60cm X 75cm including transportation etc; complete. Class C(Type XI Micro prismatic grade sheeting) shall have 10 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.28e)

Supplying and Fixing of Molded Shank Raised Pavement Markers/Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50mm, 100mm and 102 +/-2mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/-2mm and height not less than 30+/-2mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer. (Item No. 6.09)

Road Delineators: Supplying and installation of delineators(Roadway Indicators, Hazard markers, Object markers) 80 to 100cm high above ground level, painted black and white in 15cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings (Item No. 6.15)

Providing and Laying hot applied thermoplastic road marking strip on Bituminous Surface of specified shade/colour of 2.5mm thick including 1.5 Refractive index reflectorizing glass beads @ 250gm/sqm .Thickness of 2.5mm is exclusive of surface applied glass beads as per IRC 35:2015. Initial Dry reflectivity RL shall be > 250 mcd/sqm/lux measured in the initial 7 days and sustained reflectivity RL of 100 mcd/sqm/lux and Qd of 100 mcd/sqm/lux measured at the end of 2 years by means of a Standard Reflectometer of Zehntner, Easylux, Delta make capable of measuring RL & QD both according to IRC 35:2015 clause 15.5. The finished surface to be level, uniform, and free from streaks and holes complete as per direction of Engineer-in-charge and in accordance with applicable specifications.(Refer MORTH Clause 803 for technical Specification and Performance for IRC 35:2015). (Item No. 6.12a)

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter(as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant (Item No. 7.01)

Repair of RCC railing to bring it to the original shape, cleaning and repainting as per drawings etc. complete (Item No. 8.20)

Electrcity Bill (Avg. per month)

Milling of existing bituminous surface to specified depth of bituminous layer including disposal of removed material with all lift and lead upto 1000m etc complete. Using machine like Writgen(W100) or equivalent (Item No. 51.134)

Replacement of existing damaged Expansion joints by providing and laying of Strip Seal Expansion Joint System, including removal of existing damaged exp joints by dismantling of deck slab, wearing coat etc. and back filling of the recess up to final finish level with conc of grade M-35, complete as per M.O.R. T&H specification. (Item No. 51.152)

Prime coat-Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying, primer at the rate of 0.60kg/sqm using mechanical means. (Item No. 3.29)

Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen with sprayer on Dry/Hungry B.T. surface 3kg/10sqm.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.31)

DENSE BITUMINOUS MACADAM: Proving and laying dense bituminous macadam using crushed aggregates of Grading 1, premixed with bituminous binder of specified grade of Bitumen @ 4.50 per cent by weight of total mix and filler, transported to site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired density for 76-100mm compacted thickness .USING Batch mix type hot mix plant with SCADA, Sensor Paver, Vibratory roller with Stone Dust filler.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.44)

Providing and applying tack coat on the prepared surface heating by fames in Boiler and spraying bitumen set footed in bitumen boller on B.T. surface 2.5kg/10sqm.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.30)

BITUMINOUS CONCRETE: -- Providing and laying bituminous concrete using crushed aggregate of grading 1, premixed with bituminous binder @5.40% by weight of total mix and filler, transported at site with VTS, laid over a previously prepared surface, finished to the required grade, level, alignment, and rolling to achieve the desired density for 50mm compacted thickness with drum mix plant with SCADA, Sensor paver and Vibratory roller excluding prime/Tack coat etc. complete -- Bitumen of specified grade with stone dust filler.(VG-30 bulk bitumen rates are considered to arrive at rates) (Item No. 3.50)

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter(as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant (Item No. 7.01)

Metal Beam Crash Barrier -- Type-A, W : Metal Beam Crash Barrier(Providing and erecting a W metal beam crash barrier comprising of 3mm thick corrugated sheet metal beam rail, 70cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5mm spaced 2m centre to centre, 1.8m high, 1.1m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5mm, 330mm long complete as per clause 810)" (Item No. 7.30)

Road Delineators: Supplying and installation of delineators(Roadway Indicators, Hazard markers, Object markers) 80 to 100cm high above ground level, painted black and white in 15cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings (Item No. 6.15)

60cm X 75cm including transportation etc; complete. Class C(Type XI Micro prismatic grade sheeting) shall have 10 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.28e)

Trimming of grass, shurbs and weeds from the shoulders/berms and disposing off the same to suitable locations etc. complete (Item No. 8.17)

Providing and laying 12mm thick mastic asphalt wearing course on top of deck slab excluding prime coat with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface including providing antiskid surface with bitumen precoated fine grained hard stone chipping of 4.75mm nominal size at the rate of 0.005 cum per 10 square metre and at an approximate spacing of 10cm center to center in both directions, pressed into surface when the temperature of surfaces not less than 100 deg C, protruding 1mm to 4mm over mastic surface as per clause 515 etc. complete. (Item No. 14.55a)

Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 900mm out of 2mm aluminum sheet bonded with white retro reflective sheeting of Class B(Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65mm X 65mm X 6mm, 3.45m long, duly painted with with flat oil paint having alternate black and white bands of 25cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B(Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.29e)

Providing and fixing Mandatory/Regulatory sign boards in circular shape of 900mm dia made out of 2mm aluminum sheet bonded with white retro reflective sheeting of Class B(Type IV High intensity micro-prismatic grade sheeting-HIP

) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65mm X 65mm X 6mm, 3.45m long, duly painted with with flat oil paint having alternate black and white bands of 25cm width including G.I. fixtures etc; fixing the boards in M25 grade concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Class B(Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. (Item No. 6.27e)

Providing and filling annular space around footing in rock by using concrete of M15 grade etc. complete. (Item No. 15.05)

Removal of Stacking material and cleaning of water way by engaging Excavator (Tata Hitachi Ex 100) (Departmental, #SSR Item Update Failed)

Engaging of Tipper -6 cum (20 Km/Hr) (Departmental, #SSR Item Update Failed)

Bearing cleaning and pier cap cleaning for the proper movement of bearing etc. complete including all tools and machineries scaffolding etc. complete as per the direction of Site in Charge. (Item No. 51.145)

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete. (Item No. 35.25)

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. (Item No. 35.25)