Balance MEP works at NRL Corporate Office Building Project, Guwahati

Amount

Interior Lighting, Panel & Inverter

VTPN : Supply, installation, testing & commissioning of double door 500V Distribution Boards as specified with i) Copper busbars together with tapped neutral bar for individual phases. ii) Copper earth strip with tapping for EECiii) Busbar mounting MCB's individually lockable in off position.' iv) Interconnections and earthing. v) Sheet steel enclosure suitable for recessed or surface mounting with hinged lockable doors interlocked with the incomer switch.vi) Phase to phase barriers in case of 3Ph boards.'vii) Necessary support frame & painting labelling etc complete.viii) circuit wiring Power coated MS connector trunking as required with cover for the complete perfect dressing, 6 way VTPN I/C of: 160 A , O/G circuits of 6 Nos.63 A TP MCB. Make:L&T, C&S, Schnieder. Note: Switchgeras and DB should be of same make.

Supply, installation, testing and commissioning of cubicle type panels as specified and shown on drawing. i) Main AL busbars with bar type feeder connections & all internal wiring and connections. ii) Earthing all components,frame etc. to a common internal earth bar. iii) Painting all sheet metal works. iv) All accessories & supporting structure,base etc., v)Double compression Brass glands and crimping lugs for sending and receiving ends. vi) All ammeters with C.T's and voltmeter and energy meters with necessary fuses. vii) All Load Managers to have parameters like KW, KVA, A, V, PF,KVAR, Active & Reactive component of power, RS-485 port to have BMS compatibility as required & desired to complete the system. vii) Panel components as specified and as required. viii) MS base frame. ix) All switch gear to have short circuit levels as specified in the drawing. Drg. No- AHU & FCU Panel-2. Make : CPRI approved panel manufacturer

Supply, Installation, testing & commissioning of Single phase-2 KVA inverter with:15 Min battery backup complete with battery rack and necessary accessories. Make : Consul Neowatt, Luminous

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted glare free round LED Downlight with pressure die cast Aluminium housing and high transmitive Polycarbonate diffuser, (15W- 18 W), 1500-1600 Lumens(minimum), IP-20, CCT/CRI- 4000K/80, Electronic ballast, similar to Wipro make - Mollis-LD06-221-XXX-40-XX or its equivalent item of Philips / ABBY Lighting/Jaquar Lighting/Lighting technology/Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture code: LF01, Location- in all cabins.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted glare free round LED Downlight with pressure die cast Aluminium housing and high transmitive Polycarbonate diffuser, 15W- 18 W, 1500-1600 Lumens(minimum), IP-20, CCT/CRI- 4000K/80, DALI Dimmable driver compatible with Crestron make dimmer(Din Dali-2),similar to Wipro make Mollis-LD06-221-XXX-40-XX or its equivalent item of Philips /Jaquar Lighting/ Abby Lighting /Havels/Crompton/Syska as per tender technical specification & Clients/EIC approval. Fixture code: LF01. Location- Board Room & Conference room.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted Round LED COB adjustable Downlight with pressure die cast Aluminium housing and reflector with power consumption (7W-9 W) having system lumen output of 700-900 Lumens, IP-20, CCT/CRI-3000K/80,.Electronic Balast, similar to Wipro-(LD98-131-038-40-XX) or its equivcalent item of Philips/ ABBY Lighting/ Jaquar Lighting/Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture Code: LF02. Location- In all cabins, Lobby etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted Round LED COB adjustable Downlight with pressure die cast Aluminium housing and reflector with power consumption (7W-9 W) having system lumen output of 700-900 Lumens, IP-20, CCT/CRI-3000K/80, DALI dimmable driver compatible with Cresteon make dimmer (Din Dali-2), similar to Wipro make- LD56-251-060-40-DA or its equivalent item of Philips/ ABBY Lighting/ Jaquar Lighting/Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture Code: LF02. Location- Board room & Conference Room.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recess mounted LED Panel Light (600mmX600mm) 30 W (Max), 3400 lumens(minimum) with white powder coated CRCA housing with Translucence diffuser,IP-20, CCT/CRI-4000K/80, .Electronic Balast similar to Wipro make-Elate or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting /Havels/ Crompton/Syska as per tender specification & clients/EIC approval. Fixture Code: LF03. Location- Store /Hub room.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling Suspended decorative hanging light with aluminium powder coated housing IP-20, 30 W(max), 2200 Lumens, CCT/CRI-3000K/80, Electronic Balast similar to Wipro make-Orbit 0r its equivalent item of Philips/ Abby Lighting/ Havels/ Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF04. Location- Lounge area/Library.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling Suspended decorative hanging light with aluminium powder coated housing IP-20, 35W(max)-2300 Lumens, CCT/CRI-3000K/80, ElecBalast, similar to Wipro make -Orbit ring or its equivalent item of Philips/ Abby Lighting/ Havels/Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF05. Location- Meeting rooms.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of ceiling Suspended decorative hanging light with aluminium powder coated housing dome shaped, IP-20, 40W(max)-2300 Lumens, CCT/CRI-3000K/80, Electronic Balast, similar to Wipro make-Picasso dome or its equivalent item of Philips/ Abby Lighting/ Havels/Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF06. Location- Cafeteria

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket . b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling recessed (Clip On Type) end to end connected linear light with high extruded aluminium housing and high transmitive PMMA diffuser, IP-20, (25-30W)/m (2200-3300)Lumens/m(minimum), CCT/CRI- 4000K/80, Length- 4200mm, Width-maximum upto 100 mm, Electronic Balast, similar to Wipro make-Lineos LED or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting/ Endo Lighting/ Havels/ Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF07. Location- Cubicle /storage area etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling recessed (Clip On Type) end to end connected linear light with high extruded aluminium housing and high transmitive PMMA diffuser, IP-20, (25-30W)/m (2200-3300)Lumens/m(minimum), CCT/CRI- 4000K/80, Length- 3600mm, Width maximum upto 100 mm, Electronic Balast, similar to Wipro make-Lineos LED or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting/ Endo Lighting/ Havels/ Crompton/Syska as per tender technical specification & clients/ EIC approval. Fixture Code: LF07. Location- Cubicle /storage area etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling recessed (Clip On Type) end to end connected linear light with high extruded aluminium housing and high transmitive PMMA diffuser, IP-20, (25-30W)/m (2200-3300)Lumens/m(minimum), CCT/CRI- 4000K/80, Length- 3000mm, Width maximum upto100mm, Electronic Balast, similar to Wipro make-Lineos LED or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting/ Endo Lighting/ Havels/ Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF07. Location- Cubicle /storage area etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling recessed (Clip On Type) end to end connected linear light with high extruded aluminium housing and high transmitive PMMA diffuser, IP-20, (25-30W)/m (2200-3300)Lumens/m(minimum), CCT/CRI- 4000K/80, Length- 2400mm, Widthmaximum upto 100 mm, Electronic Balast, similar to Wipro make-Lineos LED or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting/ Endo Lighting//Havels/Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF07. Location- Cubicle /storage area etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Ceiling recessed (Clip On Type) end to end connected linear light with high extruded aluminium housing and high transmitive PMMA diffuser, IP-20, (25-30W)/m (2200-3300)Lumens/m(minimum), CCT/CRI- 4000K/80, Length- 1800mm, Width maximum upto 100 mm, Electronic Balast, similar to Wipro make-Lineos LED or its equivalent item of Philips/ Abby Lighting/ Jaquar Lighting/ Endo Lighting /Havels/Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF07. Location- Cubicle /storage area etc.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of flexible LED strips 15W/m(maximum) IP33, Strip light system lumen output should be minimum 800lm /m , CCT/ CRI -3000K/80 , Electronic Balast, similar to Wipro make- or its equivalent product of Philips/ Jaquar Lighting/ Lighting technology/Havels/Crompton/Syska as per technical specification & clients/ EIC approval. Fixture Code: LF08. Location- As per layouts.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of anti glare deep recessed LED spot light with pressure die cast aluminium housing and reflector,. 2W having system lumen output of 90 lumen(minimum), IP-20, CCT/CRI -3000K/80, Electronic Balast,.similar to Wipro make- Garnet or its equivalent item of Philips/ Jaquar Lighting./ Abby lighting/Havels/Crompton/Syska as per tender specification & clients/ EIC approval. Fixture Code: LF09. Location- As per layouts.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of surface mounted LED Down Light, IP 25 or better, Color Temperature 3500-4000K, neutral White, 3500-4000 Lumens, 35-40 Watt with Electronic Balast. Ref. Model Philips make-Green Space(SM294CLED40/840 PSU WP WH GM) or its equivalent of Wipro/ Jaquar Lighting./ Abby lighting/Havels/Crompton/Syska, Fixture Code: LF10.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Surface mounted LED Down Light, IP- 25 or better, Color temperature 3500-4000K, Neutral White, 2500-3500 Lumens, 30-35 Watt, Body in Aluminium Die cast , .Electronic Balast, similar to Ref Model.Wipro- Vertica( LD30-301-36W-40SS) or its equivalent of Phiips/ Jaquar Lighting./ Abby lighting/ Havels/Crompton/Syska, Fixture Code: LF11.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of Recessed ceiling mounted Round LED COB adjustable Downlight with pressure die cast Aluminium housing and reflector with power consumption Maximum upto 35-41 W having system lumen output of Minimum 3540 Lumens, IP-20, CCT/CRI-3000-4000K/80,.Electronic Balast. similar to Ref Model Wipro- Gimball (LD56-501-060-40-XX) or its equivcalent item of Philips)/ ABBY Lighting/ Jaquar Lighting/ Lighting Technology/Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture Code: LF12.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of deep Recessed ceiling mounted Round LED COB adjustable Downlight with pressure die cast Aluminium housing and reflector with power consumption 15W -18W having system lumen output of 1500-1800 Lumens, IP-20, CCT/CRI-3000K/80,.Electronic Balast. similar to Ref Model Wipro LD 98-221-024-30-XX or its equivcalent item of Philips)/ ABBY Lighting/ Jaquar Lighting/ Lighting Technology/Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture Code: LF13.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with all necessary accessories of inground floor light with Alluminium die cast light with high purity lens and reflector with power consumption 6W-7W having system lumen output of 500-650 lumens, IP 65, CCT/CRI- 3000K/80, with electronic driver, similar to Ref. model- Arcus-Wipro( LI20-600-030-30-XX) or its equivcalent item of Philips)/ ABBY Lighting/ Jaquar Lighting/ Havels/Crompton/Syska as per tender specification & Clients/EIC approval. Fixture Code: LF14.

Supply, Installation, testing & commissioning of light Fixtures complete with: a) All fixing accessories & mounting bracket. b) Earthing of fittings. c) Connections from the ceiling rose or junction box to the light fixtures including the terminations with chain & all necessary accessories. All Light Fixures with Electronic Ballast THD <10%. 40W Ceiling mounted/suspended box type LED light fixture similar to Bajaj make LED CONNECT - BPTX 40W LED 4F or its equivcalent item of Philips/ ABBY Lighting/ Jaquar Lighting/ Havels/Crompton/Syska as per tender specification & Clients/EIC approval.Fixture Code: LF15

Other Electrical Jobs

Installation only: Conduit wiring for lights/ socket outlets consisting of: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c) Insulated or base protective earth. :Primary wiring of all power points using 2x4+ 1x2.5 PE Cu PVC Wires.

Installation only: Conduit wiring for lights/ socket outlets consisting of: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c) Insulated or base protective earth. :Primary wiring to various light/power points using 2x2.5 + 1x2.5PE Cu PVC Wires.

Installation only: Conduit wiring for lights/ socket outlets consisting of: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c) Insulated or base protective earth. : Secondary wiring points extending primary circuits to various light points using 2x1.5 + 1x1.5PE Cu PVC Wires.

Supply, Installation, Testing & Commissioning of Conduit wiring for lights/ socket outlets consisting of: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c) Insulated or base protective earth. : Secondary wiring points extending primary circuits to various light points using 2x1.5 + 1x1.5PE Cu PVC Wires.

Supply, Installation, Testing & Commissioning of Conduit wiring for lights/ socket outlets consisting of: a) Wiring in 25mm FRLS HMS PVC Conduit as required with all accessories, screws,spacers,clamps, z-sections etc., b) 1100V grade FRLS PVC insulated multistranded Cu wires. c) Insulated or base protective earth. : Secondary wiring points extending primary circuits to various light points using 2x2.5 + 1x2.5PE Cu PVC Wires.

Power Point Wiring : Conduit wiring for lights fan socket outlets as per the mode of measurements described in the specifications consisting of : a) Wiring in 25/32/40/50 mm Dia PVC FRLS conduit & FR FLEXIBLE Conduit using multiple circuits as per specification as required/raceway as required.b) 1100V grade PVC insulated Cu multi-stranded ZHFR required/raceway as required.b) 1100V grade PVC insulated Cu multi-stranded ZHFR wires/Cables.c) Lighting Point wiring Shall be done in Black colour Pvc FRLS wires/Cables.c) Lighting Point wiring Shall be done in Black colour Pvc FRLS wires.Point wiring for work station area Shall be done in Floor Truncking using flexible white black ZHFR cables, Insulated or base protective earth----Primary Circuit wiring for all COMPUTER points Area using 3x2.5 Cu FLEXIBLE PVC WHITE Colour cable.

Cable Tray : Supply & installation of Hot Dip Galvanised Bolted Ladder type G I cable trays with 75mm height with 2.0 mm thickness & necessary G I supporting frame etc. for Electrical & LV cables as specified & shown on drawings. 200mm wide single horizontal/vertical tier.

Cable Tray : Supply & installation of Hot Dip Galvanised Bolted Ladder type G I cable trays with 75mm height with 2.0 mm thickness & necessary G I supporting frame etc. for Electrical & LV cables as specified & shown on drawings. 450mm wide single horizontal/vertical tier.

Cable Tray : Supply & installation of Hot Dip Galvanised Bolted Ladder type G I cable trays with 75mm height with 2.0 mm thickness & necessary G I supporting frame etc. for Electrical & LV cables as specified & shown on drawings. 100mm wide single horizontal/vertical tier.

Raceway Installation : Supply & installation of single compartment hot dip galvanised G.I raceway/Trunking of 2mm thick with 100 microns for power & data/tel as shown in drg. At ceiling/Floor level complete with: a) Wall chasing/making good. b) Raceway including cover plate etc. as per details and as specified and shown on drawings. c) All bends, T joints junction boxes etc. as specified and shown complete. 100 X 40mm SingleCompartment Raceway With openable cover

Raceway Installation : Supply & installation of single compartment hot dip galvanised G.I raceway/Trunking of 2mm thick with 100 microns for power & data/tel as shown in drg. At ceiling/Floor level complete with: a) Wall chasing/making good. b) Raceway including cover plate etc. as per details and as specified and shown on drawings. c) All bends, T joints junction boxes etc. as specified and shown complete. 200 X 40mm SingleCompartment Raceway With openable cover

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35 sq. mm & upto 95 sq. mm(clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm & upto 185 sq. mm(clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 185 sq. mm & upto 400 sq. mm(clamped with 2mm thick saddle)

Misc. Works

Repair painting / New painting by Synthetic Enamel Paint of required RAL Shade ( 2 or more coats ) on MS Structural Steel works ( Old Surface ). Make : Berger, Asian Paints.

Repair painting / New painting by Epoxy Paint of require RAL Shade ( 2 or more coats ) on MS Structural Steel works ( Old Surface ). Make : Berger, Asian Paints.

MS Structural supports (U - type frame made from ISA-40x40x4mm ) to be provided below Hydrant Pipe /Sprinkler Pipe/CI pipe above 100mm dia including the cost of 4 nos HILTI Fastener (M10x100mm )

MS Structural works in built-up/welded sections ( ISA/ISMC/Plates , etc ) to be required for MS support frames, ladders, platforms, etc. including supply of materials ,etc. at all levels from ground floor to 9th floor

Supply and installation of M12x150mm HILTI Chemical fasteners, including Anchoring Chemical ( make: FOSROC, equiv)

Supply and installation of M10x100mm HILTI fasteners.

Core Cutting of Dia 150mm in RCC Wall & Slab including making and dismantling paltform & scaffolding , etc

Chipping of RCC Wall/Slab, Beam , etc. upto 25mm thick/depth by using grinding & cutting wheels and other tools including disposal of debris at all levels including making & dismantling of temporary scaffolding ,platform , etc

Mechanical and Plumbing Jobs

Supply, installation, testing, commissioning of Internal hydrants/landing 'valves generally as specified & shown on drg. complete with: i) Twin headed landing valve. ii) first aid hose reel with 20 dia control ball valve. (2# 15m length). iii) Non percolating Synthetic, Type B hoses iv) branch pipe & nozzle. v) painted Hot dip GI hose cabinet. vi) Supply, Fixing, testing & commissioning the orifice plate complete with flange. The inlet press. 5.50kg/sqcm. The outlet pressure shall be minimum 3.50 kg/sq cm ( Make : NEWAGE/SAFEX/MINIMAX )

Internal Piping (150 n.b.): Supply, laying, testing & commissioning of heavy duty galvanised steel piping supports, clamps, painting etc. (Wet riser). Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required,applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Supply, installation, testing, commissioning of butterfly valve as per IS: 13095, CI body, SS disc, PN 16 complete with bolts, nuts, supports etc as per technical specification & complete in all respects for fire fighting application (150 mm) . ( Make : AUDCO/KSB/ALFA LAVAL/L&T )

Supply, installation, testing, commissioning of butterfly valve as per IS: 13095, CI body, SS disc, PN 16 complete with bolts, nuts, supports etc as per technical specification & complete in all respects for fire fighting application (100 mm) . ( Make : AUDCO/KSB/ALFA LAVAL/L&T )

Supply, installation, testing, commissioning of butterfly valve as per IS: 13095, CI body, SS disc, PN 16 complete with bolts, nuts, supports etc as per technical specification & complete in all respects for fire fighting application (65mm). ( Make : AUDCO/KSB/ALFA LAVAL/L&T )

Supply, installation, testing & commissioning of sprinklers generally as specified complete as shown on drgs and as required. Pendant type 15mm/68 deg C. ( Make : GRINNEL/TYCO/GEM/CENTRAL )

Supply, installation, testing & commissioning of sprinklers generally as specified complete as shown on drgs and as required. Upright type 15mm/68 deg C. ( Make : GRINNEL/TYCO/GEM/CENTRAL )

Supply, installation, testing & commissioning of sprinklers generally as specified complete as shown on drgs and as required. Pendant type 15mm/93deg C(Kitchen area). ( Make : GRINNEL/TYCO/GEM/CENTRAL )

Supply, installation, testing & commissioning of sprinklers generally as specified complete as shown on drgs and as required. Side wall type 15mm/68deg C(Standard Coverage). ( Make : GRINNEL/TYCO/GEM/CENTRAL )

Supply & Installation of sprinklers Flexible Drops individually sealed in plastic bags. (1.5 mtr long)

Supply only of spare sprinklers Flexible Drops individually sealed in plastic bags. (1.5 mtr long)

Supply and installation of flow switches complete with i) flow switch & Press. Switch ii)isolation ball valve with tamper switch iii) Orifice plate with flange to maintain apressure of 2.2ksc at the tap-off as required. iv) Drain assembly includes drain valve,test valve, sight flow indicator as shown and complete with all necessary accessories. 150 dia. ( Make : System Sensor/Spray Safe/Pottar/Dunfoss/Switzer )

Internal Piping ( 150 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping ( 100 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping ( 80 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping (65 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping(50 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping( 40 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping (32 n.b. ): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Internal Piping (25 n.b.): Supply, laying, testing & commissioning of heavy duty (Class C) GI steel piping as per IS 1239 complete with all fittings, structural pipe supports, clamps, painting etc. Structural support for pipes using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. and all accessories as required by the Engineer-in-charge to complete the job. ( Make : Jindal / Tata Steel )

Priming one coat on G.I Pipes or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. Make : Berger, Asian Paints

Painting on G.I PIPES of Sprinkler/Hydrant system (2 coats of Red(Fire Shade 536 to IS:5-1978) with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. Make : Berger, Asian Paints

Painting on G.I PIPES of Sprinkler/Hydrant system (2 coats of Red(Fire Shade 536 to IS:5-1978) with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. Make : Berger, Asian Paints

Providing and fixing cast iron traps of self cleansing design with water seal not less than 50mm 'with or without vent, including setting the trap in 1:2:4 cement concrete etc. complete. The trap shall be `P' or `S' 'type as required. CI Trap 100 mm dia outlet.

Providing & laying Brass Clean out plugs in CI lines with GI coupling and lead joint etc complete. 150mm dia pipes

Providing & laying Brass Clean out plugs in CI lines with GI coupling and lead joint etc complete. 100 dia pipes

Supply, installation, testing & Commisioning of Oil / Grease Traps (above ground) with SS 303 Details required Size of oil trap shall be 2.0mx1.5mx1.5m or ready made HDPE NS-10 model with automatic skimmer pumping as per approval from consultant & directive of engineer-in-charge.

Supplying, laying, fixing 'jointing & testing Centrifugally cast 'iron spun soil pipes / sand cast pipes including 'all fittings with or without inspection doors, 'vents, cowls at top per 'specification and as directed by Engineer-in-charge.,etc. 'jointing with lead caulked joints, painting all as Including providing and fixing MS supports for pipes fabricated from MS flats angles and plates including fixing the brackets to walls, slab, beam etc.with anchor, fasteners 12mm 'U' or 'J' bolts for fixing the pipes to clamp painting with one coat of primer and two coats of approved paint etc. complete.(In shafts,celling susp,for Rainwater & Storm watert drain only). 150mm i/d

Supplying, laying, fixing, joining & testing of Centrifugally Cast Iron spun soil pipe / sand cast pipes fittings conforming to IS:1538 specifications , jointing with lead caulked joints, painting all as Including providing and fixing MS supports for pipes fabricated from MS flats angles and plates including fixing the brackets to walls, slab, beam etc.with anchor, fasteners 12mm 'U' or 'J' bolts for fixing the pipes to clamp painting with one coat of primer and two coats of approved paint etc. complete.(In shafts,celling susp,for Rainwater & Storm watert drain only). (i) 75 mm i/d CI FITTINGS :

Supplying, laying, fixing, joining & testing of Centrifugally Cast Iron spun soil pipe / sand cast pipes fittings conforming to IS:1538 specifications , jointing with lead caulked joints, painting all as Including providing and fixing MS supports for pipes fabricated from MS flats angles and plates including fixing the brackets to walls, slab, beam etc.with anchor, fasteners 12mm 'U' or 'J' bolts for fixing the pipes to clamp painting with one coat of primer and two coats of approved paint etc. complete.(In shafts,celling susp,for Rainwater & Storm watert drain only).(i)100 mm i/d CI FITTINGS :

Supplying, laying, fixing, joining & testing of Centrifugally Cast Iron spun soil pipe / sand cast pipes fittings conforming to IS:1538 specifications , jointing with lead caulked joints, painting all as Including providing and fixing MS supports for pipes fabricated from MS flats angles and plates including fixing the brackets to walls, slab, beam etc.with anchor, fasteners 12mm 'U' or 'J' bolts for fixing the pipes to clamp painting with one coat of primer and two coats of approved paint etc. complete.(In shafts,celling susp,for Rainwater & Storm watert drain only). (i)150mm i/d CI FITTINGS :

Providing, laying, fixing jointing CPVC SDR 11 Pipes including all fittings such as sockets, unions reducers, long or short bends, elbows, nipples, flanges,checknuts, clamps, z-pieces, male and female adapters ,including all support as per supplier specification and approved drawings etc all as per specifications For pipes Layed below the Ground Lvl or Chased Walls :- Including Providing Structural support for pipe lines using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. as required by the Engineer-in-charge. 40mm n.b.(For pipe in exposed condition) . ( Make : Prince/Supreme )

Providing, laying, fixing jointing CPVC SDR 11 Pipes including all fittings such as sockets, unions reducers, long or short bends, elbows, nipples, flanges,checknuts, clamps, z-pieces, male and female adapters ,including all support as per supplier specification and approved drawings etc all as per specifications For pipes Layed below the Ground Lvl or Chased Walls :- Including Providing Structural support for pipe lines using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. as required by the Engineer-in-charge. 32mm n.b.(For pipe in exposed condition). ( Make : Prince/Supreme )

Providing, laying, fixing jointing CPVC SDR 11 Pipes including all fittings such as sockets, unions reducers, long or short bends, elbows, nipples, flanges,checknuts, clamps, z-pieces, male and female adapters ,including all support as per supplier specification and approved drawings etc all as per specifications For pipes Layed below the Ground Lvl or Chased Walls :- Including Providing Structural support for pipe lines using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. as required by the Engineer-in-charge. 25mm n.b. ( Make : Prince/Supreme )

Providing, laying, fixing jointing CPVC SDR 11 Pipes including all fittings such as sockets, unions reducers, long or short bends, elbows, nipples, flanges,checknuts, clamps, z-pieces, male and female adapters ,including all support as per supplier specification and approved drawings etc all as per specifications For pipes Layed below the Ground Lvl or Chased Walls :- Including Providing Structural support for pipe lines using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. as required by the Engineer-in-charge. 20mm n.b. ( Make : Prince/Supreme )

Providing, laying, fixing jointing CPVC SDR 11 Pipes including all fittings such as sockets, unions reducers, long or short bends, elbows, nipples, flanges,checknuts, clamps, z-pieces, male and female adapters ,including all support as per supplier specification and approved drawings etc all as per specifications For pipes Layed below the Ground Lvl or Chased Walls :- Including Providing Structural support for pipe lines using channels, tees, angles, flats & plates fabrication by cutting threading & welding if required, applying one coat of red oxide primer and three coats of synthetic enamel paint, including necessary bolts nuts, washer etc. as required by the Engineer-in-charge. 15mm n.b. ( Make : Prince/Supreme )

Providing, fixing and testing heavy quality Gun metal or brass ball valve as per IS 778 with screwed ends 16 kgm class on GI/CPVC or copper pipe lines. 50mm. (Make : Zoloto/Leader/RB )

Providing, fixing and testing heavy quality Gun metal or brass ball valve as per IS 778 with screwed ends 16 kgm class on GI/CPVC or copper pipe lines. 40mm. (Make : Zoloto/Leader/RB )

Providing, fixing and testing heavy quality Gun metal or brass ball valve as per IS 778 with screwed ends 16 kgm class on GI/CPVC or copper pipe lines. 32mm. (Make : Zoloto/Leader/RB )

Providing, fixing and testing heavy quality Gun metal or brass ball valve as per IS 778 with screwed ends 16 kgm class on GI/CPVC or copper pipe lines. 25mm. (Make : Zoloto/Leader/RB )

Providing, fixing and testing heavy quality Gun metal or brass ball valve as per IS 778 with screwed ends 16 kgm class on GI/CPVC or copper pipe lines. 20mm. (Make : Zoloto/Leader/RB )

Providing and fixing in position Gun metal / brass heavy type online Pressure reducing valves with bye pass arrangement inluding necessary ball valves,connecting pipes, pressure gauges GI Fittings like elbows, tees, union including making connection to GI/CPVC or copper Water supply lines etc complete. Inlet pressure 3 bar Outlet pressure 1.8 bar Flow rate 1 LPS to 2 LPS- 32mm. (Make : Honeywell/Danfoss/RB/Varie)

Providing and fixing best Indian make CP brass Auto air release valves with isolation valve fixed on GI lines. 20mm n.b air valve with 20mm isolation valve. (Make : Honeywell/Danfoss/RB/Varie )

Providing and fixing best Indian make CP brass Auto air release valves with isolation valve fixed on GI lines. 25mm n.b air valve with 25mm isolation valve. (Make : Honeywell/Danfoss/RB/Varie )

Fixing Client's/ Architect's approved , make special coloured vitreous chinaware wall Mounted European water closet with in-built health faucets.The item shall be with a) Concealed Duel flush cistern (Low flow 6 liter/3liter per flush), b) CI chair supports for the water closet, c) Matching coloured solid plastic seat & cover very heavy quality with rubber buffers fixed to the closet with CP brass pillar hinges, d) Two way bip tap for operating the faucets.

Fixing Client's/ Architect's approved, vitreous chinaware wash hand basin suitable for mounting below counter comprising: a) vitreous chinaware oval shaped wash basin (flowrate @4 lit/min @ 3 bar pressure), size 550mm x 400mm with supporting MS or CI brackets, b) Including Long Neck Sensor Faucet for wash basins with all allied fittings complete, c) 1No 32mm CP cast brass bottle trap with extension piece to wall, wall flange with rubber adopter waste connection, d) 1 Nos heavy quality CP brass angular stop cock 15mm size with CP brass flexible connector pipe. The supporting bracket shall be provided with 3 coats of approved paint of approved shade

Fixing Client's/ Architect's approved, chinaware urinal (Low flow 0.6 liter per flush) comprising a) Large flat back wall hung urinal size 610 x 400 x 380mm b) 15mm CP brass battery operated automatic flush valve with infra-red sensor, c) CP brass chromium plated flush piping from flush valve to urinal terminated with a 15 mm screwed spreader, d) 32mm dome CP cast brass waste, e) 32mm n.b CP cast running trap with extension pipe to wall, wall flange, rubber adopter for waste connection.

Fixing 15mm size 2 way CP brass bib tap,(Low flow @4 lit/min @3 bar pressure) heavy quality on water lines

Fixing 15mm size CP brass long neck bib tap, (Low flow @4 lit/min @3 bar pressure) heavy quality on water lines for Pantry sinks

Fixing in position single blower type hand drier including all electrical connection etc complete

Fixing and installation of of best 'Indian make S.S sink with integral drain board(Low flow @4 lit/min @3 bar pressure), single pressing of size 930mm x 460mm with supporting brackets CP brass waste, bottle trap etc. complete with single lever sink mixture with swinging spout with 450 mm long copper pipes

Fixing and installation best Indian make CP brass liquid soap dispensers with CP brass bracket capacity 250 ml.

Planning, Design, Supply, Installation, testing, commissioning and operation & maintenance for 1 years (including one years free maintenance) of Drip irrigation system as per the approved vegetation layout by the Architect of the Building ,comprising thereof ISI Marked Disc filter, Sand filter,NRV, ARV, Header Assemlby, pp manifold, Ventury assembly, pvc pipe, Control valve, Flush valve,Plain lateral,Drip tubing, Hose adapter,Drip emitters,Tubing Holder stakes ,Poly jointer, PVC and G.I fitting ,Programmable Automatic Watering Timer, and accessories like gravel, cement brick platform, metallic pop up.

Supply & installation of Rosette plate for Tyco make fire sprinklers to improve the overall appearance of the sprinkler installation by concealing the clearance holes required for wall or ceiling installation, deep, two-piece, adjustable. Make : Tyco.

VRF System

Design, Supply, Installation, Testing & Commissioning of top/Side discharge type Full Inverter VRF air-conditioning outdoor system having total capacity of 88HP ( 1 Working unit of 44 HP and 1 Standby unit of 44 HP with R-410A based refrigerant) comprising of modular type high efficiency all inverter technology based ODU with hermetically sealed scroll / twin rotary compressors suitable for R-410A refrigerant for operating condition of 415V, 3phase, 4 wire, 50Hz Ac supply,with air cooled condenser having propeller type fan with BLDC motor & protective coated fins, interconnecting piping, suction line insulation etc, microprocessor control panel suitable for automatic operation, high speed inverter control mechanism incorporating all safety function including unit mounted starter panel complete with IP-55 / rain and dust protection consisting of power disconnecting switches (Inside/Outside), starters for compressor motors, under voltage/over voltage trip, single phase preventers, communication card etc. The COP at AHRI conditions shouldnot be less than 3.5. All components should be mounted on welded steel based frame. The VRF Outdoor/Indoor units as given in the BOQ and SLD will remain same in total capacity 88 HP( 1 Working system of 44HP / 1 Standby systemn of 44 HP) however assemby of Outdoor units can be of different combination as per site condition and Manufactures recommended specification (Make: Bluestar/Daikin/Voltas/LG)

Supply, installation, testing and commissioning of 4 TR nominal capacity flow VRF ductable split ceiling mounted indoor unit equipped with synthetic washable media pre- filter, fan section with dynamically balanced blower, multispeed motor, coilsection with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete as required. The cooling capacity of indoor unit will be at air in let conditions of 27 Degree C DB and 19 Degree C WB temperature.(Make: Bluestar/Daikin/Voltas/LG)

Supply, installation, testing and commissioning of 6 TR nominal capacity flow VRF ductable split ceiling mounted indoor unit equipped with synthetic washable media pre- filter, fan section with dynamically balanced blower, multispeed motor, coilsection with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete as required. The cooling capacity of indoor unit will be at air in let conditions of 27 Degree C DB and 19 Degree C WB temperature.(Make: Bluestar/Daikin/Voltas/LG)

Supply, installation, testing and commissioning of 8 TR nominal capacity flow VRF ductable split ceiling mounted indoor unit equipped with synthetic washable media pre- filter, fan section with dynamically balanced blower, multispeed motor, coilsection with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete as required. The cooling capacity of indoor unit will be at air in let conditions of 27 Degree C DB and 19 Degree C WB temperature.(Make: Bluestar/Daikin/Voltas/LG)

Supply. Installation, Testing & Commissioning of Refnet joints for Indoor Unit – Y Joints of minimum thickness as that of refrigerant piping including Pressure testing & Vacuum testing.

Supply. Installation, Testing & Commissioning of Refnet joints for Indoor Unit – Y Joints of minimum thickness as that of refrigerant piping including Pressure testing & Vacuum testing.

Supply, installation, testing and commissioning of corded controller for the Indoor Units

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 9.5 mm dia (OD) tube with 13 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 15.9 mm dia (OD) tube with 13 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 19.1 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 22.2 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 25.4 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 28.6 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 34.9 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supplying, Installation, testing and fixing of interconnecting refrigerant piping work having 41.9 mm dia (OD) tube with 19 mm thick insulation with hard drawn / soft drawn Cu. pipe of following outer diameter, insulated with 19/13 mm thick closed cellelastometric nitrile rubber/XLPEtubular insulation (between Each set of indoor & outdoor units) of suitable density, class ‘O’ insulation complete including repairing of damage to building etc. as per specifications and as required complete in all respect. All piping above the false ceiling/building shallbe properly suitable size of cable tray/ fixed supported rods (scope included) etc as required.

Supply, Installation, Testing & Commissioning of drain piping from hard drawn CPVC material as per following sizes and duly insulated with 10 mm nitrile rubber insulation etc. as required.

Supply, Installation, Testing & Commissioning of drain piping from hard drawn CPVC material as per following sizes and duly insulated with 10 mm nitrile rubber insulation etc. as required.

Supply, installation, testing & commissioning of 24 SWG site fabricated ducts with 120 GSM GI sheets complete with all the accessories.

Supply, installation, testing & commissioning of 24 SWG site fabricated ducts with 120 GSM GI sheets complete with all the accessories.

Supply, installation, testing & commissioning of Al powder quoted supply air grille with VCD

Supply, installation, testing & commissioning of Al powder quoted return air grille without VCD

Supply and charging of R410 Refrigerant

Supply & fixing of 13mm thick nitrile rubber thermal insulation over ducts

Supply & fixing of 10mm thick nitrile rubber acoustic insulation inside ducts

Supply & fixing of 2 core x 1.5 sqmm copper, Shielded control cum trans -mission wiring of copper between indoor and outdoor unit in suitable size of cable tray/ fixed supported rods etc., as required.

Supply & laying of 4 Core X 16 Sqmm size of XLPE insulated PVC sheathed, Copper conductor armoured, power cable of 1.1 KV grade conforming to relevent IS standard as required.

Supply, instalation, testing & commissioning of main MCC cum PDB panel with outgoing feeders for 4 nos. ODU with all accessories as required.

SITC of MS Stand for ODU

Brahmaputra Commerce and Trade

M/S AFCONS

BUILDRITE CONSTRUCTION