PROVN OF SMALL ANIMAL SURGICAL COMPLEX INCLUDING ICU COMPLEX AND PHYSIOTHERAPY ROOM AT 54 AFVH HAFT CHINAR UNDER GE 970 EWS

Amount

Notes :- (i) Please refer Schedule 'A' Notes given on serial page Nos 14 to 25 of CA.

Lumpsum price worked out by the contractor for BUILDINGS WORKS (DESIGN AND BUILD) as listed in Schedule 'A' Part-I brought forward from Serial Page No. 26 of CA.

Lumpsum price worked out by the contractor for INTERNAL ELECTRIFICATION as listed in Schedule 'A' Part-II (Section-I) brought forward from Serial Page Nos 27 to 32 of CA.

Lumpsum price worked out by the contractor for SEWAGE DISPOSAL as listed in Schedule 'A' Part-III (Section-I) brought forward from Serial Page Nos 34 to 36 of CA.

Lumpsum price worked out by the contractor for EXTERNAL ELECTRIC SUPPLY as listed in Schedule 'A' Part-IV (Section-I) brought forward from Serial Page Nos 37 to 39 of CA.

Lumpsum price worked out by the contractor for EXTERNAL WATER SUPPLY as listed in Schedule 'A' Part-V (Section-I) brought forward from Serial Page Nos 41 & 42 of CA.

Lumpsum price worked out by the contractor for HOT WATER SUPPLY as listed in Schedule 'A' Part-VI brought forward from Serial Page No. 44 of CA.

Lumpsum price worked out by the contractor for REF AND AC as listed in Schedule 'A' Part-VII brought forward from Serial Page No. 45 of CA.

Lumpsum price worked out by the contractor for EXCAVATION & EARTHWORK FOR SCH ‘A’ PART-III, PART-IV (Section-I & II) & PART-V (Section I & II) as listed in Schedule 'A' Part-VIII brought forward from Serial Page No. 46 of CA.

Schedule 'A' Part-II (Section-II) Internal Electrification)

S&F street light bracket made out of GI tubing 32/ 40mm dia light grade of approx length 1.2 mtr long bend to shape suitable for security light fittings with necessary MS clamps - 02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers etc., complete all as specified and directed.

Schedule 'A' Part-IV (Section-II) (External Electric Supply)

S&F LT control panel board, outdoor type, double door, cubical type, padestal mounted slopy roof front and back both side opening. CPRI approved size 650x600x350mm IP-54 having independent compartment for bus bar, incoming feeder and each outgoing feeders, dust and vermin proof and lockable factory made fabricated out of 3.15mm thick CRCA sheet suitable for 3 phase 415 volts 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 100 Amp rating for 3 phase and bus bar of half capacity for neutral 3 phase 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 set including necessary copper cable of suitable size for MCCBs/ MCBs/ changeover switch/ inter connections, common earth bus bar of GI strip 32x6mm at bottom with panel board at two earth terminals cable glands with independent plates at bottom for each outgoing and incoming cables in cable alley panel board and painted with powder coating in siemens grey colour and provision for the following incoming and outgoing accessories, complete all as specified and directed.

Excavation in trenches by cutting of road crossing/ OCC hard standing/ interlocking tiles under boundary wall for laying of pipe including making good of the existing surface with same finish (PCC/ bitumen) to match the original finish as required, complete all as specified and directed.

Schedule 'A' Part-V (Section-II) (External Water supply)

M&L for construction of brick masonry valve chamber of size 600x600x900mm (Internal dimension) with PCC 1:4:8 foundation 150mm thick brick work built in CM 1:6 PCC 1:3:6 coping 50mm thick plastering 15mm thick in CM 1:4 to all internal and exposed surfaces including excavation earthwork in hard/ dense soil MS sheet cover 4mm thick and MS equal angle iron 50mmx50mmx6mm frame as per existing size with locking arrangement embedded in PCC suitable for 32x40x50mm gate valve and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc including dismantling old/ damaged valve pits, complete all as specified and directed.

Cost for drilling of existing DI pipe line of 80mm dia for makiing branch connection of 40mm dia including excavation, welding, jointing with required fittings such as reducer, elbow, tee etc,. Complete all as specified and directed.

Excavation in trenches by cutting of road crossing/ OCC hard standing/ interlocking tiles under boundary wall for laying of pipe including making good of the existing surface with same finish (PCC/ bitumen) to match the original finish as required, complete all as specified and directed.

M/S B A Traders (BID ID -3200636)

M/S N A Enterprises (BID ID -3200655)

M/S SHOWKAT AHMAD WANI AND SONS (BID ID -3195252)

M/S LATIF AHMAD BABA CONSTRUCTION (BID ID -3195058)

rafiq trading co (BID ID -3200693)