Spl repair of pers cook house, indep bathroom/ toilet block of bldg No P-3 and P-12A, toilet block of surgical-I and II and toilet blocks of bldg No P-3 (SM Barracks) at Tibri Mil Stn under GE Gurdaspur.

Amount

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and fair complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:6. finishing even and smooth without using extra cement complete all as specified and directed

M&L for rendering 5mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3. finishing even and smooth without using extra cement complete all as specified and directed.

Dismantling of brick work, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

M&L for brick work with flyash bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

All as per Srl item No 6 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 5 shall be reused after necessary cleaning of mortar)

M&L for brick work with flyash bricks, straight or curved on plan to any radius in half brick thick wall built in cement morter 1:4 , all as specified and directed.

M&L for preparation of new plastered/ unplastered surfaces of wall and applying two coats of cement base paint of shade as approved complete all as specified and directed.

M&L for preparation of new surface and applying two coats of oil bound distemper on walls over a coat of primer complete all as specified and directed

M&L for prepration of new plastered surface and applying three coat of white wash as on ceiling.

M&L for preparation of old decorated brick/ concrete/ plastered or unplastered surfaces walls and removing all loose material and filling the holes/ patches and applying one coat of cement base paint complete all as specified and directed.

M&L for preparation/ complete removal of existing treatment of old decorated surfaces plastered or un plastered of walls and applying two coat of oil bound distemper over a coat of primer on wall complete all as specified and directed

M&L for preparation of existing treatment of old decorated surfaces plastered or un plastered of walls and applying one coat of oil bound distemper on wall complete all as specified and directed

M&L for preparation of existing treatment of old decorated surfaces plastered or un plastered of ceiling and applying one coat of white wash complete all as specified and directed.

Taking down chowkats or frames from the opening of size not exceeding 1.5Sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed.

All as per Srl item No 16 above but size of opening exceeding 1.5Sqm but not exceeding 4Sqm.

Taking down shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed

Taking down shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete and refixing in the same opening after easing and adjustment all as specified and directed

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, painting shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, painting shall be measured and paid for separately

S&F pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for hold fast and tarring to inner surface (surface in contact with concrete/ brick surface) of chowkats and hinges complete all as specified and directed.

S&F 35mm thick flush shutters , solid core construction , with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. ISI Marked.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S&F MS framed work as in chowkats, door or gates of angle or other section with gusset plates, rail, braces,etc and similar work conforming to Fe 410-0 complete all as specified and directed.

S&F in repairs GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F GI wire cloth, 0.56 mm nominal dia. of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Hacking out old broken glass panes of any thickness description from wooden frame or stone concrete or steel frame, or brick surrounds, glazed with putty or fixed with beads and prepared to received new glass panes complete all a specified and directed

S&F sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50Sqm in each pane including wooden beading fixed with nails/ oil putty complete all as specified and directed

All as per Srl item No 29 above but figured glass pin head type & glazing with oil putty.

S&F 100 mm long butt hinges, medium weight , cold rolled mild steel.

S&F 250mm long aluminium alloy anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 200 mm aluminium, anodised, barrel tower bolts of extruded section.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised.

S&F150 mm aluminium, anodised, barrel tower bolts of extruded section.

S&F 100 mm extruded aluminium alloy handles, fabricated type, anodised.

M&L two coats of synthetic enamel painting over a coat of red oxide primer on new steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces.

M&L two coats of synthetic enamel painting over a coat of pink primer on new wooden surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete in sunken floors exc 15cm thick (above ground level) and disposing the rubbish to low laying area complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in, including bitumen primer @ 0.40 kg /Sqm after cleaning surface complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4 with water proofing compound, finishing even and fair complete all as specified and directed. (Note: WPC shall be measured and paid separately under relevant item).

Supply only integral water proofing compound.

M&L for cement concrete 1:5:10 type E-2 (using 40mm graded brick aggregates) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregates) as in sunken portion complete all as specified and directed.

S&F non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 taking down of old existing treatment and plaster complete all as specified and directed. Note :- Tiling shall have combination of two or more shade to form pattern as directed.

S&F glazed ceramic dark coloured tiles 350x250x7mm/450x 350 x 7mm thick, etc. on vertical surfaces such as skirting, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surfaces and taking down of old existing treatment & plaster, complete all as specfied and directed. Note : Tiling shall have high lighter to form pattern as directed.

Supply and fixing vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC (SWR) P or S trap, integral foot rest including connection to trap and flushing pipe, etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC complete all as specified.

S&F in repairs vitreous china urinal half stall type with brass CP spreader, white with grating and union, waste pipe for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

Supply and fixing in repair vitreous china white under counter wash basin oval type of size 490mm x 360mm including brass CP waste coupling 32mm bore, PVC waste pipe of suitable size and length complete all as specified and directed.

S&F in repair 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float and handle and flush pipe of polythylene of low or high density or PVC, 32mm dia complete all as specified and directed

Dismantling water tanks exc 250 Ltr & not exceeding 500Ltr and S&F rotational moulded polythene, triple layers, water storage tank 500 Ltr capacity, closed top, cylindrical, hoisted and fixed in positioncomplete all as specified and directed.

Dismantling water tanks exc 500 Ltr & not exceeding 1000 Ltr and S&F rotational moulded polythene, triple layers, water storage tank 1000 Ltr capacity, closed top, cylindrical, hoisted and fixed in position complete all as specified and directed.

S&F 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod

Taking up or down 15mm dia steel tubing and connections all as specified and directed.

S&F 15mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed.

Fixing only 15mm dia steel tubing with new fittings and connection in new or old position (in wall ceiling floors etc) including cleaning all as specified and directed.

Taking up or down 20mm dia steel tubing and connections all as specified and directed.

S&F 20mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed.

Fixing only 20mm dia steel tubing with new fitting and connection in new or old position including cleaning all as specified and directed.

S&F in repair tubular, towel rail brass chromium plated 20mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repair 15mm bore stop valves, cast copper alloy, screwed down, high pressure , with crutch or butterfly handles, screwed both ends for iron pipe or for unions, fancy type chromium plated with long shank and cup (concealed type) and fixed.

S&F in repair 15mm bore stop valves, cast copper alloy, chromium plated fancy type screwed down, high pressure , with crutch or butterfly handles, screwed both ends for iron pipe or for unions,

S&F in repair 20mm bore stop valves, cast copper alloy, chromium plated fancy type screwed down, high pressure , with crutch or butterfly handles, screwed both ends for iron pipe or for unions,

S&F in repair angle stop valve 15mm dia cast copper alloy chromium plated with capastan head screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs brass chroumium plated shower rose 125mm size complete all as specified and directed.

S&F in repair 15 mm dia bib tap chromium plated fancy type long body with capstan head screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair pillar taps fancy type 15mm bore, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered "HOT" or "COLD"

S&F in repair 100mm dia stainless steel grating with or without hinge type or hole type complete all specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair for shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 gms) complete all as specified and directed.

S&F in repair sinks with drainage board made of stain less steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe overall size 915mmx460mm bowl size 410mm x 330mm x160mm complete all as specified and directed.

Taking down eaves gutters and rain water pipes ( any size or pattern) , including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories

S&F 110mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2m length including all fittings complete all as specified and directed.

S&F 110mm bore PVC(SWR) pipes single socketed in any length laid in trenchs or in floors including all fittings complete all as specified and directed.

S&F 75mm bore PVC(SWR) pipes single socketed in any length with rubber ring joint, fixed to walls (any size or pattern) including all fittings complete all as specified and directed

S&F 75mm bore PVC(SWR) pipes single socketed in any length laid in trenchs or in floors including all fittings complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius with access door.

S&F 75mm bore PVC (SWR) bends any radius with access door.

S&F 110 mm bore( SWR) vent cowl.

M&L 75mm bore PVC (SWR) floor trap, plain with stainless steel grating including jointing with solvent cement.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing the rubbish to low lying areas complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate as in floor finishing even and smooth without using extra cement complete all as specified and directed.

Material and labour 75mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection finishing the surface even and fair including cutting grooves 10mm x 30mm deep at every 3.0m interval and filled with mastic filling comprising 1 part of mastic bitumen and 3 parts of sand (all by weight) complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar

M&L for 20mm thick granite ( of any type) work (table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platform sand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 as in shelves etc including demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

S&F mild steel TMT bars 6 to 8mm dia, cut to length, vent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and includidng mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Material and labour for formwork to sides and soffits of lintels, cantilevers, shelves, bands, including supports, overhangs, etc. for fair finished flat surfaces of concrete complete all as specified and as directed.

S&F in repairs curtain rod of MS pipe 25mm bore, powder coated chromium plated with fixing brackets stops rollers including fancy type knobs two Nos to each curtain rod.

Dismantling brick tiles or terracing tiles, single layer on roofs.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof.

M&L for cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate with WPC as per manufacturer's instructions complete all as specified and directed . Note :- WPC shall be measured and paid separately.

M&L for 40mm thick brick tiles laid over 15mm thick screed bed in cement mortar 1:6 and jointed, grouted flush in cement mortar 1:3 mixed 5% of crude of by weight of cement on roof padding complete all as specified and directed.

All as per Srl item No 96 above but except tiles.

M&L for PCC type B-1, 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, water trought and the like including weathering slightly rounded and threating complete all as specified and directed.

Racking out joints/ pointing to brick tiles in cement mortar, laid flat in as in floors, roofs etc.

M&L for flush pointing in cement mortar 1:3 to brick tiles complete all as specified and directed.

Excavating in post holes (or similar holes) each n. exc 0.5cum, getting our, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm , watering and removing surplus soil to a distance n exc 50m and making good surface.

M&L for palin cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for palin cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S&F for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming Fe 410-W (Gde -E-250) quality-A complete all as specified and directed.

S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 MPs as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 0.50mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding fixed with self tapping screws specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

M&L for providing hardcore of brocken stone or boulder of gauge not exc 63mm , deposited , spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

M&L for providing 100mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate ) as in floor finished concrete surface even and fair complete all as specified and directed.

M&L for machine pressed precast cement concrete coloured interlocking paver block, glossy rubber moulded of triangular/ Zingza/ Haxagone/ any shape/ design and size as approved, 80mm thick, conforming to IS 15658-2006, M-40 with grey cement and pigments, in floor/ paths/ pavement laid over and including 25mm thick sand coushioning laid dry to the profile including filling the joints with sand complete all as specified and directed. Note :- (i) Manufacturers test certificate shall be submitted alongwith sample.

M &L Forming Construction joint 100mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed.

M&L preparation of new steel steel surfces of any description over 10cm in width or girth and applying two coats of anti-rust special quality paint over a coat of red oxide primer complete all as specified and directed.

Removing excavated material exc 250m but n exc 500 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell and socket point etc complete including all fittings such as switches, Ceiling roses, regulators, light fitting, pendents, regulator, socket etc and removing the materials from site complete all as specified and directed.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) using approved colour coding, 1100 volts grade, ISI marked, including PVC conduit heavy grade, 20 mm or higher dia. with fittings concealed in wall/ on surface for ceiling with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm (nominal area) 1100 volts grade, ISI marked and connecting to the common earth dolly including provn of 3mm thick plastic laminated sheet of appropriate size and sunken CI/pressed steel terminal boxes for mounting switches, sockets and regulators etc. including cutting chases and making good to the disturbed surfaces as per existing for One light point/fan point/ bell point controlled by one, one way switch complete all as specified and directed.

All as per Srl item No 116 above but One 5 pin socket outlet 5 amps on independent board.

All as per Srl item No 116 above but One 5 pin socket outlet 5 amps on same board

All as per serial item No.116 here-in-before but with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area), using approved colour coding, 1100 Volt grade ISI marked including PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 2.5 Sqmm (nominal area) 1100 Volt grade ISI marked as earth continuity conductor and connecting to the common earth dolly for 3 pin 15/16 Amps socket outlet on independent board.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt , FRLS cable of size 6 sqmm including 6 sqmm multistranded copper conductor FRLS cable PVC insulated for earthing duly connected with earth dolly, with approved colour coding including PVC conduit heavy grade, of appropriate dia. concealed in wall with accessories including cutting chases and making good to the disturbed surfaces as per existing and taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 6 amps.

S&F socket outlet 3 pin 6 amps flush type

S&F switch piano flush type 16 amps single pole one way

S&F socket outlet 3 pin 16 amps flush type

S&F surface mounting universal batten housing made of powder coated CRCA sheet suitable for upto 1 x 18/20 W LED tube and taking down existing old unserviceable housing complete all as specified and as directed.

S&F LED tube 18/20W ultra bright LED polycarbonate tube with efficacy minimum 2000 lumens, CCT > 6500K, PF > 0.90 suitable for fitting into exsting/ new batten housing and taking down existing old unserviceable tube complete all as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report form manufacturer to Engineer-in-Charge for approval before incorporating the items in work

Supply and fix for lamp holder, PVC/ polycarbonate type with back plate, brass terminals suitable for lamp holder base of and including 9 watt LED retrofit lamp complete all as specified and as directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate, isolated body

S&F sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with bus bar SPN double door complete all as specified and directed. Note :- All the connection of incoming and outgoing wire in MCB will be made with thimble with suitable size as directed.

S&F in repair MCB single pole 6 amps to 32 amps, 'C' series complete all as specified and directed.

S&F in repair MCB single pole 6 amps to 32 amps , 'B' series complete all as specified and directed.

S&F in repair MCB single pole and neutral 6 to 32 amps, C series comoplete all as specified and directed.

S&F in repair MCB single pole and neutral 40 Amps 'C' series complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismentling blades and removing fan and blades and kept in safe coustody/ store.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

S&F in replacement fan regulator electronic type 5 step and connecting all as specified and directed.

Taking out existing old unserviceable distribution box/ sheet metal enclosure off size and making good disturbed surfaces complete with same colour.

Material and labour distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way including fixing in the wall, cutting chases, grounting and making good to match with the existing including making connections all as directed containing the folowings:- (a) MCCB 4 Pole 100 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar factory made made out of Aluminium duly insulated with wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp: 4 Nos, MCB SP 10-32 Amp: 08 Nos (Out going). (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable capacity as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil complete including dismantling existing all as specified & directed by Engr-in-charge.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

GORAYA AND CO

M/S Harjinder Singh Contractor

KAILASH CONSTRUCTION CO

Harbhajan electric co

buta singh and sons

M/S GAGAN CONSTRUCTION CO

D.RAJ And CO.

JOGRAJ CONSTRUCTION COMPANY

M/s SODHI SALES CORPORATION