85912 SPECIAL REPAIR TO BLDG NO T-14 WORKSHOP B WING AT ALC UNDER GE SOUTH PUNE

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of unrenforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregates) as in floor levelling complete all as specified and directed.

M & L for Machine cut kota stone slab flooring of size 595x595x20-25mm thick laid over and including 20 mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

Ditto all as per item no 04 above but in riser of steps, skirting, dado and pillar , set and jointed in neat cement slurry and pointed in white or colour cement to match with and over 10 mm thick backing coat in CM (1:4) including triangular filleting in CM (1:4) including taking down plaster complete all as specified and directed.

M & L for Glazed coloured ceramic tiles in vertical surface 300 x 450 x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and over 10 mm thick backing coat in CM (1:4) including triangular filleting in CM (1:4) including taking down plaster complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded stone aggregate), surface finish even and smooth without using extra cement, as in plinth protection complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position unframed work as in rafter / purlin complete all as specified and directed.

S & F Mild steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-290 (Gde E 165) complete all as specified and directed.

M & L for Providing, cement concrete 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in filleting, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

S & F 2 mm thick Fibre glass reinforced translucent corrugated / semi corrugated sheeting with two corrugations side lap, fixed with L-type of J-type or cranked hook bolts to steel / wooden members complete all as specified and directed. (Note :- Colour and pattern of sheet shall be as approved by GE)

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated / semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with L-type of J-type or cranked hook bolts to steel / wooden members complete all as specified and directed. (Note :- Colour and pattern of Galvalume sheet shall be as approved by GE)

S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with L-type of J-type or cranked hook bolts to steel / wooden members complete all as specified and directed. (Note :- Colour and pattern of Galvalume sheet shall be as per approved by GE)

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 20 mm thick rendering in CM 1:6 over Stone /brick / concrete wall surfaces as in setting coat trowelled to even & smooth w/o using extra cement for includng sagol finish for internal wall surfaces complete all as specified and as directed.

M&L for 20 mm thick rendering in CM 1:4 over Stone /brick / concrete wall surfaces as in setting coat trowelled to even & smooth w/o using extra cement for external wall surfaces complete all as specified and as directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over and including 3 mm thick wall care putty complete all as specified and directed.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Complete removal of existing treatment on walls and applying two coats of oil bound distemper over and including 3 mm thick wall care putty complete all as specified and directed.

S & F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 290 Gd E165 complete all as specified and as directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L for Gypsum ceiling board for ceiling prepainted, perforated finish, 600mm x 600mm x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600mm x 600mm, made out of 0.5mm thick G.I. tee 32 x 24 mm for main, 25x24mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle. hung from ceiling using 2 mm thick G.I. Suspension wires spaced at 1200 mm on main runners including making niches for fans/light all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons , dado etc laid bedded pointed in any mortar complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat?forms and like in cement mortar (1:4) including point?ing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) n. Exc. 1.5 Sqm each including making good distrubed portion with cement mortar 1:3 complete all as specified and as directed.

Taking down angle iron/ wooden chowkats or frames with shutters (without taking off shutters from the frame) exc. 1.5 sq. m but n. exc.4sq m each including making good distrubed portion with cement mortar 1:3 complete all as specified and as directed

Dismantling wrought iron or mild steel work in rolling shutter complete all as specified and as directed.

S&F three track sliding window with two or more shutter witth 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S&F ventiltors/ louvers with parttially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP 20048 (b) Glazing clips 19352

S & F aluminium single leaf door on pivots alongwith hydraulic door closer (Aluminiium extruded section), door lock, handles, 5 mm thick plain glass in top and 12 mm thick prelaminated partical board of exterior grade (both side laminated) in bottom panel, fixed with rubber beading and glazing clips and using aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Rectangular tube 14005 (b) Shutter Verrtical 18501 (c) Shutter top rail 19503 (d) Shutter middle rail 20060 (e) Shutter bottom rail 19511 (f) Glazing Clip 19352

S & F mild steel framed work such as grills, framed guard bars with ornamental design etc and similar work confirming to Fe-290, grade E-165 complete all as specified and as directed.

S & F Steel rolling shutters, 1.00 mm thickness of laths, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete gear operated type with chain wheel and hand chain complete all as specified and as directed.

M & L for applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer over surfaces of steel or iron of any description exc 10 cm width or girth including preperation of new or old or previously untreated surfaces complete all as specified and as directed.

S & F in repairs wash hand basins, vitreous china of size 550mm X 400mm ( flat back or angle back type) including 15 mm dia CP fancy type pillar tap & cutting for and pinning in ends of brackets or erecting stand inclusive of supply & 32 mm bore waste fittings brass chromium plated with long screwed shanks and fly nuts,screwed for iron pipe and fixing waste pipe etc. complete all as specified and as directed.

S & F in repairs 15 mm bore, 600 mm long PVC connections with PTMT nuts complete fixed to iron pipe at both ends complete all as specified and directed.

S & F in repairs 15 mm stop valves / angular stop cock, fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed both ends for iron pipe or for union complete all as specified and directed.

S & F 75 mm dia PVC (SWR) floor trap, plain with stainless steel grating including jointing with solvent cement complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades,shelves , lintels, etc.and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth in brick walls complete all as specified and as directed.

Taking up or down carefully 15mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

S&F GI tubing tubes "medium grade" galvanized with all fittings and fixed complete to walls and ceiling or laid in floors etc. 15mm bore complete all as specified and as directed.

S & F in repairs 15 mm bore bib taps,fancy type cast copper alloy chromium plated with crutch or butterfly handle, screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed.

Taking down aluminium point wiring( light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants holder,regulators sockets, light fitting etc removing materials deposited to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down old unserviceable / worn out aluminium sub main wiring of any type and size complete all as specified and as directed.

Taking down old unserviceable Main switch/DBs of any make incl teakwood board etc complete and make good the disturbed surfaces to match with existing finishes complete all as specified and as directed.

M&L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 1.5 Sqmm (Nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade, ISI - 694 marked in and including heavy duty, PVC casing caping including all accessories etc., heavy duty ISI marked, mild steel concealed sunken boxes, 1.6 mm thick and 60 mm depth with earth dolly duly painted with two coat of black bituminious paint over a coat of red oxide primer with laminated bakelite sheet of min. thickness of 3mm suitable for switches / sockets etc, including PVC insulated stranded copper conductor 1.5 Sq.mm (nominal area) single core green PVC insulated FRLS cable as earth and connecting to earth dolly complete and including cutting and chases in the wall for box and all as specified for the following:- (Note:- Making good of disturbed surfaces will be done by contractor without any claims)

(a) One light/fan/ point controlled by one switch.

(b) One 5 Amps Socket outlet point controlled by one switch on independent board.

(c) One 5 amps socket outlet point on same board with other switches

(d) One bell/buzer point controlled by one bell push

M & L for submain wiring complete with two single core 4 Sqmm PVC insulated, unsheathed multi stranded copper conductor FRLS cable, 1100 volts, FRLS grade in PVC casing caping of suitable size, including continuous PVC insulated copper earth wire 4.0Sqmm complete all as directed. (Note :- (i) 2 runs of 4 Sqmm conductor and earth wire shall be measured as one unit length. (ii) Making good of disturbed surfaces will be done by contractor without any claims. (iii) PVC casing & caping with accessories shall be ISI marked with CML number)

M & L for submain wiring complete with four single core 4x6 Sqmm, 1100 volts grade, PVC insulated, unsheathed multi stranded copper conductor FRLS cable, 1100 volts, FRLS grade in PVC casing caping of suitable size, including continuous PVC insulated copper earth wire 2x6 Sqmm complete all as specified and directed. (Note :- (i) 4 runs of 6 Sqmm conductor and two run of 6Sqmm earth wire shall be measured as one unit length.) (ii) Making good of disturbed surfaces will be done by contractor without any claims. (iii) PVC casing & caping with accessories shall be ISI marked with CML number)

M & L for submain wiring complete with four single core 4x2.5 Sqmm,1100 volts grade, PVC insulated, unsheathed multi stranded copper conductor FRLS cable, 1100 volts, FRLS grade in PVC casing caping of suitable size, including continuous PVC insulated copper earth wire 2x 2.5 Sqmm complete all as directed. (Note :- (i) 4 runs of 2.5 Sqmm conductor and two run of 2.5 Sqmm earth wire shall be measured as one unit length.) (ii) Making good of disturbed surfaces will be done by contractor without any claims. (iii) PVC casing & caping with accessories shall be ISI marked with CML number)

M & L for submain wiring complete with two single core 2.5 Sqmm PVC insulated, unsheathed multi stranded copper conductor FRLS cable, 1100 volts, FRLS grade in PVC casing caping of suitable size, including continuous PVC insulated copper earth wire 2.5 Sqmm complete all as specified and directed. (Note :- (i) 2 runs of 2.5 Sqmm conductor and earth wire shall be measured as one unit length. (ii) Making good of disturbed surfaces will be done by contractor without any claims. (iii) PVC casing & caping with accessories shall be ISI marked with CML number)

M&L for point wiring of any length using approved colour coding as per IS,with stranded copper conductor 2.5 Sq.mm(Nominal area),single core,,PVC insulated and unsheathed stranded FRLS cable 1100 volts grade,ISI - 694 marked in and including heavy duty,PVC casing caping including all accessories etc.,heavy duty ISI marked,with mild steel concealed sunken boxes 1.6 mm thick & 60 mm depth with earth dolly duly painted with two coats of anti corrosive paint over of red oxide primer,internally,covered with laminated bakelite sheet of min. thickness of 3mm sheet suitable for switches,including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core green PVC insulated cable as earth and connecting to earth dolly complete and including cutting and chases in the wall for box and all as specified for 15 amps socket outlet point on independent board complete all as specified and as directed. (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) PVC casing & caping with accessories shall be ISI marked with CML number)

S & F sheet metal enclosure with a triple pole and neutral enclosure with a three pin and earth plug and socket complete with one triple pole MCB 32 Amps incl metal clad plug top AC 415 volts and making good the disturbed area to match with existing wall finishes complete all as specified & directed.

S&F piano type switch 5 amps single pole, 240 volts complete all as specified and as directed.

S&F bell push, flush type, 5 amp, 240 volts complete all as specified and as directed.

S&F in repairs bell electrical ding dong AC 230 Volts single phase complete all as specified and as directed.

S&F ceiling rose surface type three terminals, 240 volts complete all as specified and as directed.

S&F socket outlet 5 amps 5 pin 230 volts flush type on same board complete all as specified and as directed.

S&F socket outlet multipurpose 2 in 1, 5/15 amps, 230 volts flush type complete all as specified and as directed.

S&F piano type switch 15 amps single pole,240 volts complete all as specified and as directed.

S&F lamp holder (Angle/bracket) insulated body, with back plate for batten fittings complete all as specified and as directed.

S&F in replacement of ceiling fan regulator, electronic step type delux two module, suitable for fan 48"/56" sweep complete all as specified and as directed.

M & L for Sub main wiring complete with two single core 6 sqmm, 1100volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 4 sqmm in and including PVC conduit heavy duty complete all as directed by Engineer-in-Charge (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 2 runs of 6 Sqmm conductor and one run of 4 Sqmm earth wire shall be measured as one unit length.)

M&L for cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc .. and cutting chases for concealed water tubing or concealed conduit wiring etc.. and making good, cutting not exc 10 cm girth all as specified and directed by Engineer in Charge. (Note : Making good of disturbed surfaces shall be done by the contractor without any claims)

S&F vertical 8 way TPN double door,recess mounted/wall mounted DB incl one number, MCCB as incomer 100 Amps 4 Pole 415 Volts, rated capacity & 25KA breaking capacity and outgoing MCB SP/TP,MCCB is pre-fitted at factory and including price of MCCB, complete all as specified and directed by Engineer in charge.

S&F MCB DB SPN 8 way, double door, with 200 Amp rated busbar 240 V,recess mounted all as specified and directed by Engineer in Charge.

S&F vertical 4 way TPN double door,recess mounted/wall mounted DB incl one number,MCCB as incomer 100 Amps 4 Pole 415 Volts, rated capacity & 25KA breaking capacity,and outgoing MCB SP/TP,MCCB is pre-fitted at factory and including price of MCCB complete all as specified and directed by Engineer in charge.

S&F MCB DB SPN 4 way double door with 200 amp rated busbar, 240V recess mounted with common earth dolly complete all as specified and as directed.

S&F MCB DB SPN 2 way double door with 200 amp rated busbar, 240V recess mounted with common earth dolly complete all as specified and directed by Engineer in Charge.

S&F MCB DB TPN 4 way double door with 200 amp rated busbar, 415V recess mounted with common earth dolly complete all as specified and as directed.

S&F MCB SP 6-32 Amps, 10KA, 'C' series 240Volts complete all as specified and as directed.

S&F MCB SPN 40-63 Amps,10KA, 240V,'C' series complete all as specified and as directed.

S&F MCB TPN 60A-100A ,10KA,415 V,'C' series complete all as specified and as directed.

S&F MCB TPN 16-32 Amps ,10KA,415 V,'C' series complete all as specified and as directed.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to a depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete all as specified and as directed. (NOTE:-GI earth wire and protection pipe beyond 7.5m will be measured and paid separately)

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to a depth of not less than 1.5 m below ground level connected to and incl GI strip 32x6mm and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete all as specified and as directed. (NOTE:-GI earth strip and protection pipe beyond 7.5m will be measured and paid separately)

Supply and Fix wall mounted fan 400mm sweep, oscilating type, single phase with speed regulator step type complete all as specified and as directed.

M & L for cutting and making a hole into or through cement concrete or stone masonary wall of thickness upto 45 Cm and in grith n.exc. 45 cm for fixing exhaust fan of size 300 mm sweep and providing fastners grouted in wall four nos inside for fixing of Exhaust fan and four nos outside for louvers and redressing the surface and making good with cement plaster 1:4 to match with existing surface incl lime white wash complete all as specified and directed.

S & F LED light fitting, 1 x 20 Watt, 230 Volt, surface mounting white powder coated CRCA sheet steel housing with crescent light opening in a perforated metallic frame complete with 20 W LED lamp complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed by Engr-in-charge.

Supply and fixing Integral LED Security Light Luminaire 35 W comprising of epoxy powder coated aluminium housing, enclosed with glass cover in frame suitable for 50/40 mm GI Pipe (including GI pipe) complete with accessories all as specified here-in-after including taking down old fitting complete all as specified and as directed.

S&F in replacement down rod made out of GI pipe medium grade 15mm dia with fan clamps incl drilling cutting threading etc all as directed for ceiling fan 1200/1400 sweep of following sizes:-

(a) 4 ft long

(b) 6 ft long

(c) 8 ft long

(d) 10 ft long

Supply,installing,testing and commissioning of factory made wind driven ventilator ( Mill Finish ) of througt size 600 mm with FRP base to match roofing sheet and variable angle elbow complete all as per following specification and directed by Engr-in-charge :- (i) Thickness of vanes - 0.5mm (ii) MOC of Vanes - ALuminium H-14 8011 grade (iii) MOC of Top Plate - SS 304 (0.5mm thick) (iv) MOC of Bottom of ring - SS-304 (0.5mm thick) (v) No. of Vanes - 42"

Supply, installing, testing and commissioning factory made LT feeder pillar box (KIOSK) in door type plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated copper bus bars of rating 400 amps rating installed on porcelain insulator. The panel shall be cubical and fully compartmentlised construction with double door with bus bar chamber and cable alloy, dust and vermin proof. IP-65 class protection and made of 2 mm CRCA MS sheet and 40x40x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front & back side opening type, with apron for cable entry with double door setter and locking arrangement (including provn of 65mm Godrej lock with two keys) internal wiring with PVC insulated stranded, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 Sqmm) and comprising of the following :- ( ALC )

Supply, installing, testing and commissioning factory made LT feeder pillar box (KIOSK) in door type plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 HZ AC supply system having bus bar chamber with insulated copper bus bars of rating 400 amps rating installed on porcelain insulator. The panel shall be cubical and fully compartmentlised construction with double door with bus bar chamber and cable alloy, dust and vermin proof. IP-65 class protection and made of 2 mm CRCA MS sheet and 40x40x6mm thick MS angle iron frame work, powder coated finish over one coat of red oxide primer on outside surface and painted inside with two coats of red oxide primer, front & back side opening type, with apron for cable entry with double door setter and locking arrangement (including provn of 65mm Godrej lock with two keys) internal wiring with PVC insulated stranded, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size (but not less than 2.5 Sqmm) and comprising of the following :-( ALC )

M&L in replacement sheet metal enclosure including MCCB 63 Amps, 16KA, TPN 415Volts with thimbles, glands and fixing arrangements such as fastener, nuts, bolts complete all as specified and as directed by Engineer-in-Charge.

M&L for on load change over switch of rating 200 Amps,4 pole 415 volts with side handle assembly type,having door interlock complete as per the direction of Engineer-in-Charge.

Supply, lay, test connecting and commissioning underground cable LT 1100 volt grade heavy duty XLPE insulated with aluminum stranded conductor armoured complete laid in trenches/fixed to poles /drawn through pipes/floor with suitable size cable glands criping type cable lugs etc including taking down all as specified and directed of the following sizes :-

(a) 25 Sqmm 3.5 core

(b) 10 Sqmm 4 core

(c) 16 Sqmm 4 core

S&F in replacement of smart glow recess mounting LED 2'x2' luminaries of 36 Watt with an inbuilt sensor thus avoids unwanted hassle of creating space for sensors.White acrylic drop light dissipator white powder coated CRCA housing with LEDS.Plane front frame fixed to housing.Concave acrylic diffuser enables lighting complete all as specified and as directed.

S&F in replacement of smart glow slim surface mounted round LED panel 20 Watt Polycarbonate body with premium diffuser to ensure glare free & even distribution of light complete all as specified and as directed.

Disconnecting and taking down the existing ceiling fan of any size, and depositing to MES E/M store for safe custody complete all as directed by Engr-in-Charge.

M & L for cleaning ,overhauling, lubricating , spray painting,wih one coat of synthetic enamel paint , writing MES No., after overhauling and refixing the fan complete all as directed by Eng-in-charge.

S&F LED highbay 100 watt luminaire a fine ventilation technology for better thermal management and its cuuting edge technology with LED 100 Watt and with flat white high transmission acrylic diffuser white/neutral white colour temperature etc, prewired and all accessories complete all as specified and as directed.

S&F in replacement of smart glow recess mounted,compact vertical,square shaped downlighter with removable driver suitable for low ceiling heights and 18W LED complete all as specified and as directed.

Anand Trading Co (BID ID -3114909)

M/s.BAJRANG CONSTRUCTION (BID ID -3106276)

UNIQUE ENGINEERS (BID ID -3115742)

V.R.PRAJAPATI AND CO. (BID ID -3126919)

Suma Construction (BID ID -3126344)

L.K.R.TIWARI CONSTRUCTION (BID ID -3122696)

Manak landmarks (BID ID -3126471)