Construction of Office Building and Residential Building for SIB unit at Car Nicobar.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Weather shed, Chajjas, corbels etc., including edges

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab over 0.50 sqm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed three layer or graded plain wood particle board medium density grade I, ISI marked and conforming to IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Providing and fixing bright finished brass handles with screws etc. complete:

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

30 mm thick plain PVC door shutters

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

Using R2 series with frame (70 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Casement window double panels with fixed mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles.

Using R3 series with frame (55 mm & above) x (45 mm & above) & sash (55 mm & above) x (65 mm & above) & mullion (55 mm & above) x (65 mm & above). (Height upto 1.8 metre).

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing M.S. fan clamp type I or ll of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing bolts including nuts and washers complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

G.I. pipes

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion.

Coupler

Single tee with door

75 mm bend

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Barge board (Upto 300 mm)

12 mm cement plaster of mix:

1:4(1 cement: 4 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix:

1:4(1 cement: 4 fine sand)

6 mm cement plaster of mix:

1:3(1 cement :3 fine sand)

Finishing walls with Acrylic Smooth exterior paint of required shade:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade:

Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete.

20 mm diameter.

Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board

510x1040 mm bowl depth 178 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe

32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

25 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm nominal bore

40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length

20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

100 mm diameter

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour.

Circular type

100 mm nominal dia

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Supplying and filling in plinth with pulverised sand under floors including, watering, ramming consolidating and dressing complete.

Providing and fixing bright finished brass sliding door bolts with necessary screws etc. complete

Providing and fixing soil, waste and vent pipes: with UPVC pipe coforming to IS:13592 type B including jointing of pipes and fitting with solvent cement etc complete as per direction of Engineer-in-charge. (i) Single socketed pipes.

75 mm dia pipe.

110 mm dia pipe.

Providing and laying hollow cement concrete blocks walling up to floor five level 200mm thick using hollow block of size 400mm x 200mm x 200mm of mix 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 12.50mm nominal size) having a crushing strength of 3.5 N/mm2 at 28 days as per I.S. 2185 (Part I) 1979 laid in cement mortar 1:6 (1 cement: 6 coarse sand) complete.

Providing and laying hollow cement concrete block walling upto floor five level 100mm thick consisting of using hollow block of size 400 mm x100mm x200mm having a cruching strength of 3.5N/sqmm at 28 days as per IS: 2185 (part-I) 1979 laid in cement mortar 1:6 complete.

Providing and Laying hollow cement concrete blocks walling upto floor five level 200 mm thick consisting of hollow block size 400x150x200 mm of mixed 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 10 mm nominal size) having a crushing sttrength of 3.5 N/Sqm at 28 days as per IS:2185 ( Part -I) 1979 laid in cement mortar 1:6 (1 cement:6 coarse sand upto floor five level).

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade

Two or more coats on new work.

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with aluminium Zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm).

Providing and fixing 20 cm wide, 60 cm overall semi-circular plain Aluminum sheet gutter with iron brackets 40x6mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete as per the direction of Eng-in- charge.

1 mm thick Aluminum sheet

Extra for providing and fixing wind ties of aluminium 40x 6 mm flat Aluminium section.

Providing and fixing PVC terminal guard etc. complete as per the direction of Eng-In-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (GI Pipe)

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing PVC bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete as per the direction of Eng-In-charge.

PVC door bend 100 mm dia

Providind and Fixing health faucet with fittings arrangement of approved quality as perthe direction of EIC

15 mm nominal bore

Providing and fixing CP brass two way bib cock of approved quality.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

First class teak wood /Padauk

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately)

First class teak wood /Padauk

35 mm thick shutters

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing cement concrete surface drain in given average size with 100 mm thick bed and 150 mm thick side walls concrete with 1:3:6 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 1i/c 12 mm cement plaster 1:4 (1 cement :4 coarse sand ) with floating coat of neat cement inside the drain, exposed sides and top of walls i/c earth work in excavation and disposal of surplus earth with in a lead of 50mtr.

Providing and fixing in position Aluminium Plate of required thick as per design for expansion joint.

30 mm wide

Providing and fixing C.I cover with frame (light duty) 455x610 mm internal dimesion total weight of cover and frame to be not less than 38 kg (weight of cover 23 Kg and weight of frames of 15 kg)

Constructing soak pit 1.20x1.20x1.20 m filled with brick bats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Constructing cement concrte 1:2:4(1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) thick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) .

Constructing of Septic tank with cement concrete was with 1:3:6 (1 cement, 3 coarse sand 6 graded stone aggregate 40 mm nominal size) including RCC precast top slab 10mm thick with 1:1:5:3(1 cement, 1.5 coarse sand, 3 graded stone aggregate 20mm nominal size) 20mm thick foundation concrete 1:4:8 (1 cement, 4 coarse sand, 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with water proof cement mofinished with floating coat of neat cement, 40mm thick C.C. Flooring 1:2:4(1 cement, 2 coarse sand 4 graded stone aggregate) including RCC buffle wall 10 cm with terminal guard and two manhole cover of size 455x610 mm rectangular C.I. Cover (light duty) fixed in RCC Slab M.S. Foot rest and 30 cm c/c etc complete as per design, drawing and direction of Enginee-in-charge.

50 users having Inside dimensions 3.70 x 1.50 x 1.85including 30 cm free board.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR LS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch,modular plate, suitable size G.I/PVC box and earthing the point with 1.5 sq.mm. FR LS PVC insulated copper conductor single core cable etc as required

Group C

Group A

Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit alongwith 1 No 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.

2x 2.5 sq.mm + 1x 2.5 sq.mm earth wire.

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 x 10 sq.mm + 2 x 6 sq.mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

(a). 5/6 amps switch.

(b). 3 pin 5/6 amps socket.

(c. Telephone Socket Outlet

(d) TV antenna Socket outlet

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing PVC batten/angle holder including connections etc as required

Installation, testing and commissioning of ceiling fan / wall mounting, i/c wiring the down rods of standard length (upto 30cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable etc as required.

Installation of exhuast fan in the existing opening, including making good the damage, connection, testing, commisioning etc as required

a) upto 450 mm sweep

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required - 02 pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC shetahed in the existing surface/recessed steel/PVC conduit as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way , Double door

12 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6-way (4+18) Double Door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commisioning etc as required

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600 mm x 600 mm x 3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangements and watering pipe of 2.7 meter long etc with charcoal/coke and salt as required

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Laying of one number PVC sheathed /XLPE power cable of 1.1 KV grade of following size in the existing DWC/Hume/Metal pipe as required.

above 35 sq.mm and upto 95 sqmm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Supplying and fixing cable route marker with 10 cm x 10 cm x 5cm thick GI plate with inscription there on, bolted/welded to 35mmx35mmx6mm angle iron, 60 cm long and fixing the same in ground

Erection of metallic pole of following length in cement concrete 1:3:6 ( 1 Cement:3 Coarse sand: 6 Graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc as required a)above 4.5mtrs and upto 6.5 mtrs

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying of Edge lit sleek surface square Luminarie 18 Watts with white powder coated die cast housing and diffuser for low glare illumination Make Bajaj Model Gint surface SQ BGSLO Sleek Surrface 18W WH SQ LED or its equivalent as per the specifications and Brand- Philips, Crompton, Havells approved by Engineer-in-charge

Supplying of LED Batten Luminaire 20 watts comprises of extruded aluminium housing,polycarbonate diffuser Make Philips Model BN170CLED20S-6500 PSUL120 or Equivalent Make- Crompton, Bajaj, Havells

Supplying of BEE- 5 star energy efficient BLDC Ceiling fan (1200mm sweep) without Remote for operation of 230v, i/c wiring down rod standard length (upto 30Cm) with all accessories etc as required. Make:- Crompton, Energion Riviera (w/o Remote) or Equivalent Make Havells, Usha, Bajaj

Supplying of Exhaust fan 250 mm sweep (PVC Body) Make Crompton Brisk Air Neo 250 mm sweep with all accessories as required or Equivalent Make Havells, Usha, Bajaj

Supplying of following LED lamps Make- Havells/Philips/ Crompton /Bajaj

09 watts

Supplying of LED mirror light 12 watts Make Luker Model LITA T5 or equivalent. Make:- Bajaj/ crompton/Philips.

Supplying of LED Post top lamp 40 watts Die cast aluminium -IP 65 protection Make Bajaj Model BCF IMG 40W LED NW PT ASYM or equivalent. Make:- Havells/ crompton/Philips.

Supplying of following size ISI marked PVC insulated and PVC sheathed/ XLPE (heavy duty) 1.1 KV grade ArmouredAluminium conductor cable conforming to IS:7098 (Part - I ).

95 sqmm x 3.5 Core

Supplying and Fixing Integrated All-in-one Solar Street Light 30 watts , efficacy more than 175 lumens/watt , Equiped IN sensor with Lithium ferro Phosphate battery, solar panel and charger built into the luminarie, Pressure die cast aluminium fitting Make Philips, Model Sunstay, BRP710LED30 CW MR S1 12 V LFP AIO Solar Equip IN-with sensor or equivalent Make- Bajaj, Crompton, Havells on the existing pole

Supplying of 06 mtr high hot dip galvanised octagonal poles with 130mm bottom A/F & 70mm top A/F made up of 3mm thick HR sheet alongwith base plate of size 200X200X12mm thick with 0.5mtr long hot dip galvanised standard single arm bracket made up of 40NB dia GI pipe suitable to mount on pole having top 70mm Make Bajaj Model BOP-6030 or equivalent Brand -Philips, Crompton, Havells.The pole shaft shall be made from hot rolled steel plate confirming to IS 2062/ BS EN 10025. All octagonal poleshafts shall be provided with the rigid base plate manufactured from MS steel confirming to IS:2062 of suitable thickness with provision for fixing foundation bolts.

Supplying and laying of one number double walled corrugated high density polyethlene pipe having corrugation on the outer wall and plain surface inner wall confirming to IS: 16205 ( PART-24-2018) Complete with necessary HDPE fittigs for protection of 1.1 KV grade under ground cable directly in ground at a depth of 50 cm i/c excavation and refilling the trench.

63 mm outer dia and 51 mm inner dia

Supplying and laying of one number double walled corrugated high density polyethlene pipe having corrugation on the outer wall and plain surface inner wall confirming to IS: 16205 (PART-24-2018) Complete with necessary HDPE fittigs for protection of 1.1 KV grade under ground cable directly of following size on wall surface as required

63 mm outer dia and 51 mm inner dia

Supplying and fixing Co2 Type fire Extinguisher of capacity 4.5 Kg Confirming to IS 15683 with all accessorries etc as reqd.

Supplying and fixing of Mechanical Foam Cartridge Operated (60 Gm as per IS 4947) Type Fire Extinguisher Filled with AFFF Foam 9 Ltr Capacity with ISI Mark conforming to IS: 15683 etc as reqd.

Supplying and fixing Fire Bucket made from 24 SWG GI Sheet similar to IS 2546

Supplying and fixing wall mounting bracket for fire buckets

Supplying, Installation, Testing and Commissioning of 1.5 Ton 5 star Inverter Split type Air Conditioner (1 phase 230 Volt) with rated cooling capacity of atleast 5000 Watts Make- Hitachi Model- RAS.E518PCCIBWB of equivalent cooling capacity in Vestar/ Blue Star/ IFB/ MITSUBISHI/ O GENERAL/ DAIKIN/ SHARP/LG with copper Condenser coil and rotary compressor with all accessories, cutting, drilling holes on the wall , cementing, painting to give an even look and smooth finish, wrapping PVC non adhessive white tape over insulation of gas pipe etc as required including 05 KVA voltage stablizer of Make V Guard Model VND 500 (Voltage Range 150V-285V,15Amps.) or equivalent & Pre-fabricated stand for keeping outdoor units of 1.5 Ton Capacity split type AC as required as per the direction of E-I-C

Supplying, Installation, Testing and Commissioning of 2.0 Ton 5 star Inverter Split type Air Conditioner (1 phase 230 Volt) with rated cooling capacity of atleast 6100 Watts Make- Hitachi Model- RAS.E522PCBIBWB of equivalent cooling capacity in Vestar/ Blue Star/ IFB/ MITSUBISHI/ O GENERAL/ DAIKIN/ SHARP/LG with copper Condenser coil and rotary compressor with all accessories, cutting, drilling holes on the wall , cementing, painting to give an even look and smooth finish, wrapping PVC non adhessive white tape over insulation of gas pipe etc as required including 05 KVA voltage stablizer of Make V Guard Model VND 500 (Voltage Range 150V-285V,15Amps.) or equivalent & Pre-fabricated stand for keeping outdoor units of 2.0 Ton Capacity split type AC as required as per the direction of E-I-C

Supplying, installation, testing & commissioning 16 channel NVR with recording/transfer rate of 160 Mbps, up to 08 MP resolution for Preview and Playback Make CP Plus Model CP-UNR-4K4162-V4 with (2x 10 TB SATA Surveillance HDD Make Toshiba Model HDWT31AUZSVA) or its equivalent

Supplying, installation, testing & commissioning IR Bullet outdoor Camera Resolution 20fps @ 5MP Lens 3.6 mm fixed lens (2.8 mm Optional) IR- 30 M Make CP Plus, Model CP-URC-TC51PL3C-L-0360 or its equivalent

Supplying, installation, testing & commissioning IR Dome indoor Camera Resolution 20fps @ 5MP Lens 3.6 mm fixed lens (2.8 mm Optional) IR- 30 M Make CP Plus, Model CP-URC-DC51PL3C-L-0360 or its equivalent

Supplying, Installation, testing and commissioning of 10/100 16 Port PoE with 2 10/100/1000 Mbps Uplink (Power Budget 200 W) Make - CP Plus Model CP-DNW-HPU16G2F1-20 or its equivalent

Supplying, Installation, testing and commissioning of 32” (80 cm) Smart TV with resolution 4K (1366 x 768) Connectivity- Bluetooth, HDMI, adapative AI sound with wall mounting stand. Make LG Model 32LR570B6LA

Supplying, Installation, testing and commissioning of 1 KVA/800 W online UPS ,DC Voltage System 24V DC, Phase-Single Phase with ground, Battery type SMF 12V/9AH x 2 Nos (in-Built Batteries), LED/LCD Display Indications, Make- Microtek, Model E2 1KVA 24V IB or its equivalent

Supplying and installation of Wall mount modular rack 2U Size with acrylic fiber glass door Lock n key (450 mm x 350 mm) Make CP Plus Model CP-HA-RK4535VM-2U or its equivalent

Supplying and drawing of CAT-6, 4 Pair UTP 23AWG Cable in the existing surface /recessed PVC conduit /casing caping etc as required.. Make:CP Plus Model CP-EUT-6TGL23-100 or its equivalent

Supplying and fixing of following size of ISI medium class PVC conduit/casing caping along with all accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying installation, testing and commissioning of Diesel Generator set Make Ashok Leyland, LEYPOWER, Model LP 100, Power rating 100 KVA/80 KW Engine Model H4G4DE100 rating 92 KW/122 HP @ 1500 RPM 4- cylinder, AC alternator, Three Phase, 415 Volts, 50 HZ 0.8 PF, with Acoustic enclosure (sound proof) as per central pollution control board (CPCB-IV) approved DG set (Manual) with complete accessories including battery as required or its equivalent model as per the above specifications.

Supplying, Installation, Testing and Commissioning of grid interactive roof top solar photo voltaic power generation system -15 Kwp with accessories mentioned below Make Tata Power Solar or any equivalent make as per the speciication and approved by EIC

Tata Power Solar - TOPCON – Solar Panel ( Non DCR)

Goodwe /Solis / Solax inverter - 1.00 Kw

Module Mounting Structure - 1.00 kw

DCDB - 1.00 kw

ACDB - 1.00 kw

MC4 Connectors - 1.00 kw

Lugs and Electrical Items & Accessories - 1.00 kw

Earthing Pit (Copper Bonded) - 1.00 Mtr

Lightening Arrestor – Conventional - 1.00 Mtr

DC Cable - 1C X 4 Sq.mm. Copper Cable -50 Mtr

AC Cable - 4 C - 50 Sqmm – Aluminium Cable - 50 Mtr

Earth Cable - 1C x 10 Sqmm Aluminium Cable - 100 Mtr

Installation and Transportation Charges - 1.00 Job