Special Repair of Govt. Polytechnic at Lisana at Rewari in Rewari Distt. (Boys Hostel)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (b) in cement [HSR 8.5 (b)]

Dismatnling Roofing (g) demolishing mud phaska in tile terracing [HSR 8.8 (g)]

Stripping and stacking slates or tiles of a roof [HSR 8.10]

Scraping (c) cement plaster [HSR 8.32 (C )]

Dismantling white or coloured glazed tiles (to be carefully removed) [HSR 8.38]

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled [HSR 8.18] (a) doors

(b) windows

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. [HSR 16.60]

12 mm thick cement plaster 1:6 [HSR 15.7]

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. [HSR 13.13]

Providing two coats of exterior acrylic emulsion paint. 2nd Quality (HSR 16.79 (a))

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete: - (b) door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate [HSR 18.34 (b)]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in- charge.). HSR 17.93 (a) - Note 1 under 17.18] Note:- The Agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material. (ii) 35 mm thick

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash etc. (non-conferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete, fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). [HSR 17.90 b]

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick, exceeding 40 sq dm areas. [HSR 18.30 (b)]

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) size of ceramic Glazed tiles of Size 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used as approved by Engineer-in-charge. [HSR 14.92(b)]. Note:- The Agency to whom the work is alloted will have to produce original bill / voucher for all quantity in token of proof of purchase of material.

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. [HSR 16.25]

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/ primer of reputed make firm such as Goodlass- Nerolac, Berger, Garware, Jenson, Nicholson, Asain & Shalimar shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer -in- charge(HSR 16.2)

Preparation of ply wood surface for painting inlcuding sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as Goodlass- Nerolac, Berger, Garware, Jenson, Nicholson, Asain & Shalimar shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer -in- charge (HSR 16.3)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. [HSR 16.5]

Recovery items: The rates quoted against recovery items will not be included in the total amount rather is will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specification) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under:- Good Brick tile @ 4.50 Each

Brick tile bats @ 400 P.Cum

Old Chowkats @ 200 Each

Old Flush Door @ 100 Each

Glazed window @ 50 Each Note: - All quantities of the above materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

P.H. Estimate:- DISMANTLING H.C.I.SOIL PIPES (a) 100 mm internal diameter [HSR 30.96 (a)]

DISMANTLING H.C.I.SPECIALS (a) 100 mm internal diameter [HSR 30.97 (a)]

Providing and fixing PVC pipe completed in all respect. (NS)

FIXING GALVANISED MALLEABLE IRON HOLDER BATS HOLD FASTS to pipe lines fixed on walls and ceilings including all cutting to walls and making good to original condition. [HSR 28.28] (i) 15 mm internal diameter

(ii) 20 mm internal diameter

(iii) 25 mm internal diameter

FIXING AND JOINTING GUN METAL PEET VALUES (HEAVY PATTERN) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, INCLUDING CARTAGE from divisional stores or nearest railway station to site of works. [HSR 28.29] (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

CONSTRUCTION BRICK MASONRY INSPECTION CHAMBER SIZES AS GIVEN BELOW UPTO 0.60 METRE AVERAGE DEPTH in cement mortar 1:5 LIME CONCRETE with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 BENCHING 12mm THICK CEMENT PLASTER 1:2 with a floating coat of 1mm thick of neat cement R.C.C.1:2:4 SLAB 100mm THICK /C.C.TOPPING 50 mm THICK WITH 455 MMx 455MM/ 455MM x 610MM INSIDE LIGHT DUTY C.I.INSPECTION CHAMBER COVER AND FRAME weight as per I.S.I. specification painted WITH 3 COATS OF black bitumastic superior paint complete as per standard design. [HSR 29.84] (c) Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with R.C.C. slab)

(b) Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern I weighing 38 kg with C.C. topping)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (a) Size 580 mm (i) White [HSR 30.2 a(i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NONCONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above. [HSR 30.4]

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (i) White plastic seat (Solid) [HSR 30.13 (i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin- charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC. WHITE Size 630mm X 450 mm with one no. tap [HSR 30.41 (a) (iv)]

PROVIDING AND FIXING IN POSITION 32MM DIA.G.I.WASTE PIPE EMBEDDED IN WALL or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge) [HSR 30.48]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET. (a) VITREOUS CHINA WARE ROSE SHOWERS White (i) 175 mm diameter [HSR 30.66 a (i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with raw slugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (a) 25 MM DIA C.P.BRASS ADJUSTABLE 750 mm long [HSR 30.68 a(i)]

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the wells etc. (a) C.P.BRASS (i) Soap dish large [HSR 30.70 a(i)]

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHORMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC.] (a) INDIAN MAKE (i) 600mm X 450mm [HSR 30.71 a(i)]

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (c) Bib cock [HSR 30.75 (C )]

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer in- charge) (a) 15 MM STOP COCK (i) Stop cock male and female end [HSR 30.76]

(b) 20 MM STOP COCK (i) Stop cock male and female end

PROVIDING AND FIXINGIN POSITION M.S.OR HEAVY FLAT IRON CLAMPS made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. SOIL WASTE vent or anti pipes to walls COMPLETE IN ALL RESPECTS INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS ETC., AND PAINTING. [HSR 30.88] (a) 100 mm internal diameter

(b) 75 mm internal diameter

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, all respects to the satisfaction of Engineer-In-Charge. (Except civil work).(HSR 30.119)

Providing & fixing PVC Rain Water pipe of 6 Kg Pressure of ISI mark in cement mortar during masonary work. (HSR 13.89) 100MM dia PVC pipe 6 Kg Pressure

Providing & fixing PVC Bend ISI Mark. (HSR 13.90) 100mm dia PVC Bend.

EXTRA FOR PROVIDING AND FIXING VITREOUS automatic flushing CISTERN INCLUDING FITTINGS and brackets instead of C.I. flushing cistern COMPLETE (b) 10 Litres capacity cistern (i) White [HSR 30.37 (b) (i)]

PROVIDING AND FIXING IN POSITION 32MM DIA.G.I.WASTE PIPE EMBEDDED IN WALL or lead waste pipe (weighing 3.47kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge) [HSR 30.48]

PROVIDING AND FIXING IN POSITION AUTOMATIC BRASS BALL VALVES IN TANKS. (b) WITH PEASTIC BALL (iii) 25 mm internal diameter [HSR 30.110 (b) (iii)]

Providing & laying C.P.V.C pipe with specials Comp. in building . (NS) (ii) 20 mm internal diameter of pipeline

(iii) 25 mm internal diameter of pipeline Note :- In case of any difference in the unit and nomenclature of any of the HSR items of Civil & P.H. work depicted in this DNIT and the given in HSR, the unit nomenclature given in HSR shall be applicable.

Sandeep Yadav, Contractor

Krishan Kumar, Contractor

Surender Singh, Contractor, Rewari

Pawan

Vipin Kumar S/o Sh. Jagdish Singh, VPO Tiwala, Charkhi Dadri