Construction of Forest Protection/Anti-depredation Camp at Palamu

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 B Brick work in C.M. (1:6) in superstructure and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, scaffolding raking out joints to 15 mm depth, curing taxes and royalty all complete as per building specification and direction of E/I

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).LINTEL BAND

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Providing TMT steel reinforcement 8mm dia rods to dia as per approved design and drawing excluding carriage of M.S. roads (Straight or in coils) to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

8mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} @ 30%

10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} @ 30%

12mm TO 25MM (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} @ 30%

Supplying , fitting and fixing M.S. grill made of 20x6cmm M.S. flat as per approved designe and drawing , properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site , hoisting as per building speciffication and direction of E/I.

Providing and fixing fan hook of 16mm dia TMT M.S. bar I meter long bent to required size and shape placed in position and fixed in RCC slab/beam at the time of casting all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of Oil bound Distemper of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of plastic emulsion paint of approved shade and make over new steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I

Providing 150mm, wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of earth work involved with 75mm cement concrete (1:4:3) over one brick designation 75A, flat soiling in proper grade and slope at tile base the drain duly palster in C.M. (1:3) with punning over surface all complete as per building specification and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing pressed steel door frames conforming to IS: 351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges,jamb,lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by engineerin-charge. Profile B - Fixing with adjustable lugs with split end tail to each jamb

S/F 35mm thick solid core type non-decorative single leaf flush door and windows with black board core banded with high quality phenol formaldehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding door bolts tower bolts, handles or rings hooks and eyes, cleats sand block as per schedule taxes and royalty all complete as per building and direction of E/I.(one side teak)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length, ncluding cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :

New work (Two or more coats applied @ 1.43 ltr/ 10sqm over and including priming coat of exterior primerapplied @ 2.20 kg/ 10 sqm)

Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar (1: 4) laid and jointed with grey cement slurry including rubbing and polishing complete with :

Providing and laying Ceramic glazed floor tiles of size300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm

1 2 . 5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.

Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1 ) conforming to IS 1328 BWR Type

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

Carriage of matarials

Bricks - 8km (1k + 7p)

Sand - 10km

Chips - 22 km

Metal - 22 km

Local Sand - 3 km

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages(2 HP)

FR PVC insulated 3 core 4 sq.mm copper wire

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Supplying fittng and fixing 40 mm high viterous white glazed earthen ware E.W.C with "P" trap of perry Hindustan or any other IS make includin supplying and fixing 15 litres C.I mosquito proof low down flushing cistern of approved make with complete as per specification and direction of E/I

(a) 12.5 lit low level C.I Cistern

Supplying, fitting and fixing viterous white glazed earthn were wah hand basin of parry or Hindustan or any other I.S.S approved do do all complete job

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply. Includng all CPVC plain & brass threaded fitting, I/C fixing the pipe with clamps at 1.0m spacing as per dirction of E/I

15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply. Includng all CPVC plain & brass threaded fitting. This includes jointing of pipes & fitting with one step CPVC solvent cement trenching, refilling & testing og joints complet as per direction od E/I

25 mm nominal outer dia pipes

Providing and fixing 15 mm dia male ended C.I Body brass spindle valve and seat bib cock of approved quality (Wt not less than 400gms) with extra socket all complete as per specification and direction of E/I

Providing and fixing 15 mm dia male ended C.I Body brass spindle valve and seat bib cock of approved quality all complete as per specification and direction of E/I

(a) 15 mm dia

Providing an fixinf G.M non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I

(iii) 25 mm dia.

(B)Vertical-(iii) 25 mm dia

Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos at both ends etc. all complete as per direction of E/I

(ii) 15 mm dia and 45 cm long

Making holes in wall for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/I

(b) 250 mm thick wall

Supplying fittng and fixing flat back or angular, lipper front vitreous white glazed earthware urinal of "Hindustan" ,"perry" or any other approved I S S make with complete as per specification and direction of E/I

(b) Slanding corner (600mm X 350mm)

Providing and fixing 15 mm dia male ended 15 mm brass bib cock of approved quality (Wt not less than 350gms) with extra socket all complete as per specification and direction of E/I

Supplying ,fitting and fixing the following items complete with all materials as per specification and direction of E/I

(c) (ii) CP Brass dish container medium quality with screws and hings

(i) CP Brass towel rail 20mm X 600mm bracket container

(b) Mirror of 6mm thick plate glass bevelled edge mirror including CP brass revolving fitting 3m ply wood board and C.P hinges to fix with mirror

(i) 600mm X 450mm size

Providing and placing on terrace (at all floor levels) polyhelyne water storage tank, Isb 12701 marked with cover and suitable locking arrangementb and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank

Providing 15 ltr capacity pull &let go high level CI cistern complete with bsll cock & pair of bracket - do all complete job

Supplying 32 mm dia PVC waste pipe 750mm long with coupling all complete job

Supplying H.C.I fitting cowel all fitting

50 mm dia (wt without ear and socket 2.5 Kg)

80 mm dia (wt without ear and socket 3.25 Kg)

100 mm dia (wt without ear and socket 3.25 Kg)

S/F F angular stop cock all job complete

Wiring for light point/fan point/exhaust fan poinVcall bell point, with 1.5sq.mm FR PVC insulated copper conductor single core in surface/recessedPVC conduit, piano type switch,phenolic laminated sheet with suitable size MS box and earthing with point 1.5sq mm FR PVC insulated copperr conducter single core cable etc as required

Wiriug for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.nrm FR PVC insulated copper conductor single core cable for loop carthing etc as required.

Circuit/ submain wiring in steel conduit :- Wiring for circuit/ submain wiring along with earh wire with the followingsizes of FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit as required

2x1.5 sq.urm+ 1x 1.5 sq.mm earthwire

2 x2.5 sq.mm + I x2.5 sq.mm earth wire

2 x 4.0 sq.mm + I x 4.0 sq.mm earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, compiete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way single door

Supplying and fixing 6 amps b 32 amps rating; 240 volts, 10 KA, "8" curve miniature circuit breaker suitable for furductive load of following poles in the extsttng MCB DB complete with connection, testing and commissioning as required 6/32 amps, single Pole, "8" series

Supplying and fixing following rating double pole,240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(63 amps)

Supplying and fxing 2 pin 5 amp. Ceiling rose on the existing junction box/wooden block including connection etc. as required

Supplying and fixing brass batten / angle holder including connection etc as required.

Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with ISI markd HRC fuses, including drilling holes in metal board . making connections. etc. as required (63 amps)

Supplying and fixing of following sizes of PVC/G.I box on surface / recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

75 mm x 75mm x 50mm deep/ (4" x 4")

72 mm x l46mm x 48mm deep/ (4" x 7")

Supplyrng and fixing of following piano type switch / socket on the existing switch box / cover including connections etc. as requted.

5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

4 pin 5/6 amps, socket outlet

5 pin 5/6 amps, socket outlet

6 pin 5/6 amps, socket outlet

7 pin 5/6 amps, socket outlet

8 pin 5/6 amps, socket outlet

9 pin 5/6 amps, socket outlet

10 pin 5/6 amps, socket outlet

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

MOHAMMAD IMRAN (BID ID -643087)

M/S RADHYA ENTERPRISES (BID ID -643329)

M/S ADITYA RAJ ENTERPRISES (BID ID -643267)