Balance Work of upgradation of Radiation Oncology Block (Raising of 2nd floor at SMHS Hospital Srinagar).

Amount

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar

Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo Wood

19mm thick commercial ply board work for covering top & sides of wooden stage.

AC3 8mm thick wooden floor planks in two colour combinations incl. cost of beedings & packings complete.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

20mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand)

Providing and fixing ISI marked flush door shutters 35mm thick conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.22.1 With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class deodar wood

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm

Providing & fixing Mica lamination of desired shade /colour (2 colour combination lam archard Mica Brand or equivalent as per approved shade using Heatex Adhesive complete job as directed . Thickness of Mica not less than 1mm.

Providing & fixing of angle iron framed built up steel tubular sections duly welded & jointed as desired incl. locking arrangements as asked for /as directed complete incl. providing & erection of MS Pipe with Holdfasts etc. incl. priming coat of Red Oxide.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Providing/manufacturing kitchen cabinets making necesdsary opening for SS Sink made out of WPC material duly fixed flush to wall incl. making necessary partitions inside with openable drawers as directed by the Engineer at site complete job. Incl all other accesories. work top shall not be less than 600mm wide & not less than 2100mm in length (WPC-Wood PLastic Composite Board) shall be 18mm thick with work top of Jet Black Granite 15mm thick with double moulding complete job

Providing & fixing of following hardware fittings incl. cost of screws, nuts & bolts:-

Rod Lock (Link Quality) 200mm

Rod Lock (Link Quality) 300mm

Tower Bolt (Heavy Duty) Aliminum 230mm

Tower Bolt (Heavy Duty) Aliminum 150mm

Handle Heavy Duty Aliminum 150mm

Hydraulic Door Closer

SS Hinges Heavy Duty 100mm

Providing & fixing of Square Mesh (Welded Mesh) 25x25mm complete job for closing of all openings in gables etc. under truss work incl. fixing with MS Flats 50mm wide incl. priming coat of Red Oxide

Steel Work with MS Flats welded to Iron Mesh Bolted to Eaves Boarding MS Flat 3x50mm

MS welded Mesh 25x25mm

Providing & fixing of Gyp Board false ceiling excluding GI Grid Work replacing damaged ceiling complete job incl. finishing with jointing tap & wall putty as directed.

Providing & fixing of lead vinyle linning to door shutter specially ordered complete job for radiation effect incl. all costs.

M/s Shan Constructions

ABDUL SALAM DAR

abdul rashid malik