Improvement for Black Spot and Left Turn Nehru Nagar Square Road under M-3 Sub Dn, New Bhopal Division, PWD Bhopal.

Improvement for Black Spot and Left Turn Nehru Nagar Square Road under M-3 Sub Dn, New Bhopal Division, PWD Bhopal.

Bill of Quantities (BOQ)

Probable Amount of contract :

(Rs. in Figures) : Rs. 36.14 Lacs

(Rs in words) : Rupees

Time Alloved : 3 months

Excavation in Soil using Hydraulic Excavator and Tippers with disposal up to 1000 meters. Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting suitable earth to the embankment location and disposing off unsuitable earth with all lifts and lead up to 1000m as per relevant clauses of section-300 of specification.

(SOR I.No. 3.3)

Providing and laying Plain/Reinforced cement concrete in open foundation including form work shuttering etc. complete as per drawing and technical specifications and as per relevant clauses of sections 1500, 1700 & 2100 with.

(i) Concrete with plant (Drum Type) and placing

B PCC Grade M20

(SOR I.No 12.6 (ii)

Dry Lean Cement Concrete Sub- base

Construction of dry lean cement concrete Sub- base over a prepared sub-grade or drainage layer with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver finisher with electronic sensor, compacting with 8- 10 tonnes vibratory roller, finishing and curing as per clause 601 of specification complete in all respect

(SOR I.No. 6.1)

Deduct from Item No.6.1 above if paver finisher with electronic sensor is not used and laying, (The acceptance criteria regarding level, thickness, surface regularity, texture finish, strength of concrete and all other quality control measures shall be the same as in case of machine laid work.)

(SOR I.No. 6.2)

Cement Concrete Pavement

Construction of un-reinforced, dowel jointed, plain cement concrete pavement with M-30 grade concrete over a prepared sub base with cement , coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with electronic sensor slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, admixtures as approved, curing compound, finishing to lines and grades as per drawing as per IRC-15-2011 and as per relevant clauses of section 602 of specifications complete but excluding cost of steel in dowel bars and tie rods etc. including groove cutting for width of 4 mm- 6mm and 1/3rd depth of PQC within 8-10 hrs of placing/ finishing of PQC including cost of cutting including cleaning of groove and providing approved sealant filling etc. as per clause 602.2.10 and 600.10 and IRC-57-2006 as per drawing and as per specification.

(SOR I.No. 6.4)

Deduct from Item No.6.3 & 6.4 above if slip form paver with electronic sensor is not used and laying, compaction is done by fix form paver having 60 mm vibratory needle @ 2 Nos. per metre. (The acceptance criteria regarding level, thickness, surface regularity, texture finish, strength of concrete and all other quality control measures shall be the same as in case of machine laid work.)

(SOR I.No. 6.5)

Road Delineators

Supplying and installation road delineators (road way indicators). as per MORT&H Clause 806. The structure shall be made in roll forming process having height of 800-900 mm above the ground level, width not less than 100 mm and shall extend not more than 200-300mm below the ground while being installed, buried or pressed in to the ground in confirmation with IRC:79: 2019, are as directed by the Engineer-in-Charge. The guide post with pure polyester powder coating with minimum 40 microns thickness for protection against corrosion, on top of which Type XI retro reflective sheeting confirming to IRC-67 and ASTMD-4956 shall be pasted on both sides complying to IRC:79:2019. The delineator should consist of minimum retro reflective unit exposed area of 330 cm2 white color, full cube corner micro prismatic non-metallic retro reflective sheeting on each side conforming with IRC 67:2022 and meeting the coefficient of retro reflection values as per ASTM D 4956 Type XI label specification. The delineator shall have grooves across the- length to make the reflective sheets vandal-proof.

(SOR I.No 8.21)

Road Markers/Road Stud with Lense Reflector

Providing and fixing single mound twin shanked molded Road Markers/Road Stud made of poly carbonate or ABS body and shall support a load of 13635 Kg tested in accordance to ASTM D 4280 and complying lo specifications of Section-5 of IRC:35-2015 and clause 804.2.2 of MORT&H and Section-5 of IRC:35-2015. he reflecting panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entering the lens face. The slope or retro-reflecting surface should be 35 + 5 degree to base. The reflective marker shall be fixed to the road surface using the epoxy/ adhesives and the procedure recommended by the manufacturer. No nails shall be used to affix the markers so Cubes capable of that they do not pose safety hazard on the road. The contractor shall submit a two-year replacement warranty. for satisfactory field performance including stipulated retro-reflectance of the reflecting panel. (Make- 3M /AVERY DENNISON/ ORAFOL / ALCOLITEA / AUTOMARK)

(SOR I.No 8.23)

Retro- reflectorised Traffic signs Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2012 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide IRC: 67:2012 clause 6.7.3.2 and clause 801.3.3 of MoRT&H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2012 and Table 800-1 of MoRT&H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2012 and Table 800-3 of MoRT&H specification of in the clause IRC 6.8 of the IRC 67-2012 and clause 801.3.7 of MoRT&H message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on MS sign post of size 80 x80 x 3mm Square pipe of 3 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back support frame of 25x50x1.25mm tubular frame with the help of suitable sizes pop rivettes of 6mm or by the help of G I / Nickle Chome plated nut & bolts to be hammered after tightening. 7 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture brand like 3M/Avery Dennison/ Orafol make as per clause 6.9 of IRC: 67:2012 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2012 for the product offered shall be submitted by the contractor.

Note:- Manufacture name and date of manufacture is to be printed (Embossed) at the backside of the board

(v) 60cm x 45 cm rentangular

(SOR I.No 8.12 (v))

Direction and Place Identification signs more than 0.9 sqm size board.

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2022 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide IRC: 67:2022 clause 6.7.3.2 and clause 801.3.3 of MoRT&H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2022 and Table 800-1 of MoRT&H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2022 and Table 800-3 of MoRT&H specification of in the clause 6.8 of the IRC 67-2022 and clause 801.3.7 of MoRT&H message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on 2 nos. of MS sign post of size 75mm x75mm x 6mm of 3.60 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back-support frame of 25mmx25mmx3mm angle. 7 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture brand like 3M/Avery Dennison/ Orafol Make as per clause 6.9 of IRC: 67:2022 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2022 for the product offered shall be submitted by the contractor.

(SOR I.No 8.7)

Providing and Laying of 2 or more sets (6 Nos. each set) Dual Ribs Pattern Rumble Markings on roads with vehicular speeds of more than 50 Km/hr laid as per the spacing recommended for each set under Table 11.1 and Fig. 11.2 of IRC 35:2015 using Plastirib 2K, or equivalent 2 component cold plastic profiled material Each Dual Rib pattern rumble marking shall have width of 500 mm. Each dual rib pattern rumble marking shall have 2 ribs each of Width of 100 mm and height 20 mm. Gap between two ribs shall be 300 mm. Each rumble marking shall be made complete with drop on Soild Plus reflective glass beads @ 300 gm / One Square Metre spread throughout the surface of marking. The finished surface to be levelled, uniform and free from streaks and holes, including surface cleaning and cost of all materials etc. complete.

(SOR I.No 8.32 )

Road Delineators

Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings.

(SOR I.No 8.22)

Providing and fixing of Rumble Strip made up of TPU polyurethane (PU) Material size 500L x 100W x 15H mm and fixing of Rumble Strip in Bituminous grout/ Epoxy and Screwing the same with M.S Screw 15 x100mm etc. i/c removing asphalt at the site, Material, labour for fixing grouting and for controlling traffic during fixing etc. complete.

(SOR I.No 8.56)

Total Rs.

Say Rs.

Sub Engineer Sub Divisional Officer Executive Engineer M-3 Sub Division New Bhopal Division P.W.D. Bhopal PWD Bhopal