Formation of Scientific Park Near Bus Stand in Udhagamandalam Municipality

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shalesmurram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Earth work excavation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc., complete - Open Earth Work Excavation

Supplying and filling in foundation and basement with Crushed Stone Sand (M-Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.-

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc, which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification i) For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

ii) For plane surfaces such as RCC roof slab, roof beams, lintels, waist slab, landing slab etc.,

M-20 CONCRETE - Providing and laying in position, standarised design mix M-20 Grade using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350Kg/m3 and maximum water cement ratio of 0.55, including admixture(plasticiser/super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.70 cu.m.)940.50Kg of 20mm machine crushed stone jelly and with about (2.80 cu.m.)462.00Kg of 10-12mm machine crushed jelly and with about (4.25 cu.m.)701.25Kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor/roof slabs wherever neccessary without clambing extra, etc. complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requierments of IS 383-2016. (No separate payment will be made by the department for the exces usage of materials as per design mix.)

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Brick work in CM 1:5 (one cement& five sand) using II class ground moulded bricks of size 9"X43/8"X 2 3/4" including finishing, curing, etc... complete complying with standard specification.-

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Supplying and fixing inposition of best and approved colour corrugated sheets of best quality of 0.50mm thick with necessary bolts, nuts, bitumen washers and cutting the sheets to the required size with all labour charges including cost of all materials and conveyance charges etc., complete

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Cement concrete in 1:3:6 [one cement and three sand and six aggregate using 20mm and 40 mm size ISS grade machine crushed chips at 1/3 Part and 2/3 Part respectively including the cost of mixinglaying curing etc., complete complying with S.S.

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

Weathering course concrete using best quality broken brick jelly of size 20 mm uniform gauge in pure slaked lime in the proportion of brick jelly to lime being 32 to 12 1/2 by volume and laid over the RCC roof slab in a single layer and consolidated to the finished thickness by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling jaggery and lime water etc. complete complying with standard specification.

Finishing the top of roof with one course of approved first quality machine pressed tiles of size 230 mm x 230 mm x 20 mm thick of approved quality laid in cement mortar 1:3 (one cement and three sand) 12mm thick mixed with water proofing compound confirming to Indian standard specification as approved by the departmental officers at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same mortar mixed with the water proofing compound and red oxide etc. complete complying with standard specification.

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam to a required thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,..

Plastering with cement mortar (1:5) 12mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc.complete as per standard specifications (S.1,306)

Plastering with cement mortar (1:3) 10mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.1.309

Plastering in cement mortar 1:4 mix 12mm thick using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortar etc.complete complying with standard specification--10m2

White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting external wall with two coats of best approved quality of cement painting over a existing priming coat of cement primier over cement surface wall as dirceted by the depotment officers including cleaning preparing the surface etc,complete complying with standard specification.The cement paint should be got approved by the depotment officers before use on work

Paving the floor with design antiskid ceramic tiles (colour and shade as directed) of size 305mm x 305 mm x 6mm in all floor aver a base layer of cement mortar 1:3 (one cement and three sand) 20 mm thick laid in situ and pointed with same coloured cement.

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour I Set in cement mortar 1:2 (one cement,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail. Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter and should have provision to fix AL drops, tower bolt hinges and lock plates inclusive of cost of all materials etc. complete complying with thew standard specifications.

Providing and fixing louvered ventilator fabricated from roll formed sections made of galvanized steel colour coated or reported they still as per IS 513 D quality galvanized as per IS 277 with the zinc of 120 grams per sqm) with the total coated thickness of Paint specification: court at sections should be with primer court of epoxy primer of 5-7 microns thick, Finish painted with polyester paint of 12 16 microns thick, Dimensions of the sections: the section for external frame should be 57 mm x 33 mm Fixing details: the section should be cut to length joint with profile to profile component Accessories: glass holding planes made of glass filled nylon Glass: louveres to be provided with 4 mm pin headed glass Grill: ventilator should be provided with grill made of 10 mm square MS bar to 12 mm x 5mm flat at 4 inch intervals. Total grill unit should be powder coated and fix it to ventilator frame with screws. The frames should be fixed to brick or concrete / Masonry walls and floor by means of self expaning screws

Steel Door : Manufacturing and supplying and fixing of steel doors with the following specifications. MS angles of size 40x 40x 6mm at 3.5 Kg./m are used for the outer frame and MS angle of size 35x 35x 5mm at 2.6 Kg/m for the shutter frames. Stiffeners with 32x6mm at 1.5 Kg./m MS flat is provided as the lockroll of the door and welded intact of both ends to the shutter frame 18g CR sheets of best quality is laid as panel in the shutter frames 18x5mm at 0.7 Kg./m MS flat is welded over the 32x6mm at 1.50 Kg./m MS flat on the rear side of the door sandwitching the CR sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg./m MB flats are provided diagonally onthe rear side of the shutter 2 Nos. of hinges in case of single leaf and 4 nos. of hinges in case of double leaf shutters is provided. 6 Nos. of hold fasts 120mm length spilced at the ends are wolded to the outer frame of the door. Tower bolt 2 Nos. one at the top and the other at the bottom are provided.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un?plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug

Painting external wall with two coats of best approved quality of Synthetic Enamel Paint over a including One Coat of priming of Alkali Resistant Distemper Primer over cement surface wall as dirceted by the depotment officers including cleaning preparing the surface etc,complete complying with standard specification.The cement paint should be got approved by the depotment officers before use on work

Supply and Delivery of DWC Structured Wall Polyethylene Piping Systems (Pipe with online/offline coupler and elastomeric sealing ring) with required specials non-smooth external annular corrugated and smooth internal surface (Double wall) (SN 8 Class) for non-pressure underground sewerage, drainage application generally as per IS-16098 (Part-2) type B 150mm dia pipe

Supply and delivery and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc... 1000 lits

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve/Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work. 25mm Gun metal Gate Valve

32mm Gun metal Gate Valve

Supplying and fixing in position 15mm dia brass CP screw down tap/ Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works ) SD Tap

Pillar Tap

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works . 25mm dia

32mm dia Water delivery line

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges up to 4 meter height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. 32 mm dia

Supplying PVC Specials (with working pressure 10 kg./ sq.cm.)in water supply arrangements (both in internal and external water supply arrangements Coupler 25 mm Dia

32 mm Dia

Elbow 25 mm Dia

32 mm Dia

BEND 25 mm Dia

32 mm Dia

Tee 25 mm Dia

32 mm Dia

End Cap 25 mm Dia

32 mm Dia

Reducer 20 mm x 15 mm

25 mm x 20 mm

32 mm x 25 mm

Reducer Tee 20 mm x 15 mm

25 mm x 20 mm

32 mm x 25 mm

Reducer Elbow 20 mm x 15 mm

25 mm x 20 mm

32 mm x 25 mm

Jet Nipple 25 mm Dia

32 mm Dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). PVC Elbow 110mm dia

75mm dia

PVC Elbow with Door 110mm dia

75mm dia

PVC Tee 110mm dia

75mm dia

PVC Tee with Single Door 110mm dia

75mm dia

PVC "Y" with Single Door 110mm dia

90mm dia

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthenware wash hand basin of size 550 x 400mm (with pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class Gl waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylon connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position Indian Water Closet (Oriya type) of size 580 x 440mm White/Color glazed earthen ware of approved quality and brand with "P" or "S" trap conforming to BIS with Sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two Sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm diaCl pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof/floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works)

Supply and fixing in position of best Indian make white / colour glazed earthenware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with Gl pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masonry and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing position CI Nahani Trap/Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes, Bemds, other clamps, screws nails etc..complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe 14 Ka/SaCml

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 60W LED street light fitting with LED (Lower end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .SD-457 P.NO203 ELECTRICAL DATA

Supply and Run of 2 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 10 sq mm copper wire with painting of suitable colour.

Earthling as per ISI Specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm and with 20mm dia copper earth flat of size 125mm x50mmx6mm, with funneling arrangement using charcoal, common salt, G.I.reducer, check nuts etc., and masonry work and providing RCC cover slab 38mm thick for the Brick masonry including cost of steel and fabrication of reinforcement etc., complete in all respects as directed by the departmental officers. (SD 233)

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers.(SD 75)

Supplying and Fixing of 3 Phase DB with MCB 12 way TPMCB sheet steel distribution boards (flush type/surface type) fitted with bus bars and neutral links with three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pille incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB/RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and separate provisions for MCB/Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder etc.complete in all respects as directed by the departmental officers

Supply and run off 2 of 2.50sqm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continuous earth connection by means of 1.50 sqm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departmental officers. (derived from SD 55)

Supply and fixing of TNEB meter Board suitable for 32 A Three phase service connection with 32A fuse unit(500V)32A neutral link and earth link (1" x 1/8" Copper flat) on T.W plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1" thick oneither sider with painting withsuitable bolt and nuts for fixingthe TW plank on wall withearth connection and interconnection with 7/20 PVCinsulated copper wire from EBmeter to fuse unit. SD 127)

Supply and run of 4 core 16 Sq.mm PVC Armoured cable of 1100 V grade with ISI mark.(Part Er) V

Supply and run of 4 core 10 Sq.mm PVC Armoured cable of 1100 V grade with ISI mark.(Part E c) V

Wiring with 2 x 1.5 sqmm (22 0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). SD 23

Wiring with 2 x 1.5 sqmm (22 10.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

18 W LED Tubelight for T8 Fitting Single side (15-e)

Providing Double Seater arrangements with Ready made Granite benches 20mm thick Slab with 1500mm wide , 600mm height. The cost shall include all labour and materials and as directed by the departmental officers.

Supply fixing and errection of CCTV Camara including cost and Conveyance of all materials to site etc complete as per Specification internet Protocol Camera 2.4 MP 3.6 MM Lens Outdoor new instalaltion

Network Video Recorder (32 CHANNEL-2 SATA) PWD SOR (M-2198) VOL I

24 Port Patch Panel PWD SOR (M-2236) VOL I

Rack With Accesssories -9 U RACK PWD SOR (M-222) VOL I

Armoured LAN & CCTV Cable (CAT-6) PWD SOR (M-2184) VOL I

Led tv for display (Q) 24" LED TV

Designing, Supply & installation of ‘CONSERVATION OF ENERGY’ including fabrication,Painted with good quality PU coating with proper surfacepreparation , Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanationboard in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: Wonderful gadget with swinging balls proves the law of conservation of energy. Technical specification of the gadget:Product Size :4’*2.5’ Top Frame1 1/4" Gi Pipe Thickness 2 Mm 1 1/2" gi pipe 2mm thick,2”SS Ball, 4mmplastic coated steel Rope etc.

Designing, Supply & installation of ‘PASCAL LAW ‘including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Concept: The pressure given at one point of a liquid in a closed vessel is uniformly distributed to all points of the same fluid. This famous pascal’s law is explained here.Technical specification of the gadget: Dimension In : l x b x h: 2' * 1' * 3' 1" Gi pipe B class, semi hemisphere silver vessel, Piston hand pump, 1 1/4" GI pipe, 1 1/4 * 1/4 MS flatetc.

Designing, Supply & installation of ‘HYDRO ELECTRIC POWER PLANT’ gadget including fabrication, Painted with good quality PU coating with proper surfacepreparation , Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanationboard in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. The concept of hydel power used for electricty generation is demonstrated in this model. Length - 3' Width -1'. Height-18". Components - impeller, dynamao, led bulbs, frp water tank, acrylic cover, electric water pumping motor.

Designing, Supply & installation of ‘PLANETARY MOTION’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Concept:The Planets revolve at higher pace nearer to the sun and slower when its farther from the Sun. This concept can be visualized Technical specification of the gadget:Product size: 4'*4' height 3' Fibre reinforced polymer made curved surface of size 4’X4’ with a groove to allow a metal ball to roll, 1 1/2" GI pipe 2mm thick, 3/4" GI pipe B class, 1/2" GI pipe B class, 2 * 1/4 MS flat, 6mm MS round rod, 3/4 * 1/4 MS flat, 30mm Steel ball etc.

Designing, Supply & installation of‘AIR CUSHION’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: Thin air film is formed by jet of air columns coming out of thousands of pin holes on the table top. Near zero friction is felt with the gliding movement of the strikers above the sheet of air.TECHNICAL SPECIFICATION:Overall dimension: Height -5’ Width- 2'.Length -2'.Electric motor 1/4 HP for generating air cushion installed in a closed chamber.

Designing, Supply & installation of ‘KNOW YOUR WEIGHT’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: This play gadget is based on the first order lever principle. The children can note down their weight with the help of graduated platform on the top. The children's weight is balanced against the huge mass kept at one end.TECHNICAL SPECIFICATION:Overall dimension: Height -5’ etc. The concept of First order lever is applied to calculate the weight of person waling on top platform. Total length -8'. Height -2'. Width-18".

Designing, Supply & installation of ‘CIRCUS OF ENERGY’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: The massive structure with combination of paths explains about potential energy, kinetic energy , centrifugal force, transformation of energy from one form to another and work done by spending energy. Technical specification of the gadget: product size:20’*10’ height:10’6mm ms round rod¾*1/4 ms flat 1 ¼ gi pipe½ gi pipe skating wheel magnetic coil 1 set led bulp wire 6206z ball bearing 6 no 1 *1/4 ms angle

Designing, Supply & installation of ‘PERIODIC TABLE’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Concept:All elements are introduced with their symbol. Atomic weight, atomic number and crystalline structure of each element can be learnt. Technical specification of the gadget:Overall dimension – 5’ long: 5’ high. Main frame made up of 40 m.m galvanizediron pipe.

Designing, Supply & installation of ‘VOLUME TANK’ including fabrication, Painted with good quality PU coating with proper surfacepreparation , Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanationboard in two language (English & Tamil) Size - 3' X 3'. Height 30". FRP made tank suspended with various shapes solids. Cocept - The volume of various shape solids are derived from the displaced water with the help of measuring jar provided.

Supply & installation of ‘ELLIPSE TABLE’ including fabrication, Painted with good quality PU coating with proper surfacepreparation , Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanationboard in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Overall length - 5 feet. width - 30 ". Height - 30". The concepts of two centers for an ellipse is illustrated with two strikers kept at two centers ofthe ellipse.

Supply & installation of‘PARABOLIC DISHES’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: Sounds waves can behave light light rays. They reflect, converge & diverge. A set two identical parabolic dishes explains it well. TECHNICAL SPECIFICATION:FRP Dish Diameter – 54” – 2 Nos Height – 6’ Above G.L No of dishes – 2 2 Nos – Rods at focal point – 25mm GI ‘B’ class etc.

Supply & installation of‘SWING IS A PENDULUM’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: The frequency of a simple pendulum is inversely proportional to it's length. Here three swings with 3 different lengths are suspended to play. The longest swing has very less frequency while comparing the shortest swing having more frequency. TECHNICAL SPECIFICATION:Overall dimension: Height -10’ width -5'.length -10'.

Designing, Supply & installation of ‘AUTOMOBILE WORKING MODEL’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Concept: A real time working model of an automobile explains the functioning of internal combustion engine. Clutch, gearbox, hydraulic brake, steering and differential mechanisms. Technical specification of the gadget:product size:8’*5’ height :7’auto mobile engine,clutch ,gear box,hydraulic brake,steering movement ,propeller shaft with proper labelling. Colurfully fabricated FRP car shell is fitted on 25 m.m GI pipe to attract students.1 ½ gi pipe 1” gi pipe 1/2” gi pipe 1*1/8 ms flat

Supply & installation of ‘SEE BECK SIREN’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc.Length- 2'. Height-30". Width-12".

Supply & installation of ‘ANATOSAURUS’using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year. . The gadget to painted with quality PU coating after proper surface preparation.Concept: Anatosaurus lived in the late Cretaceous period, about 70-65 million years ago, toward the end of the Mesozoic Era.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension170" X 48" X 90"

Supply & installation of ‘TYRANNOSAURUS REX’ using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year. The gadget to painted with quality PU coating after proper surface preparation.Concept: It lived during the late Cretaceous period, about 85 million to 65 million years ago. T. rex lived in a humid, semi-tropical environment, in open forest with nearby rivers and in coastal forested swamps.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension 8'X4.5' etc.

Supply & installation of ‘ANKYLOSAURUS’using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year. . The gadget to painted with quality PU coating after proper surface preparation.Concept: Ankylosaurus was the last and the biggest of the armored dinosaurs (Ankylosaurids) to evolve. Ankylosaurus lived during the late Cretaceous period about 70-65 million years ago. Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat.Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension157" x 34" x 34"

Supply & installation of ‘GSLV’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Specification : complete 22 feet height ,16 inch dia.25X25X6 mm mild steel angle frame fabricated and installedfor holding the rocket upright.

Supply & installation of ‘CORYTHOSAURUS’using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year.. The gadget to painted with quality PU coating after proper surface preparation.Concept: Corythosaurus lived during the Cretaceous Period, roughly 80 to 65 million years ago, toward the end of the Mesozoic, the Age of Reptiles.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension180"x 48" x 80"

Supply & installation of ‘NEANDERTHAL WOMAN (MAN 3)’ using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year.. The gadget to painted with quality PU coating after proper surface preparation. Concept: Early Neanderthals lived in the Last Glacial age for a span of about 100,000 years. The fossils were found in Europe and parts of Western and Central Asia.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat.Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension42" X 30" X 27"

Supply & installation of ‘NEANDERTHAL MAN (MAN 1)’ using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size)comprehensive A.M.C for 1 Year.. The gadget to painted with quality PU coating after proper surface preparation.Concept: Early Neanderthals lived in the Last Glacial age for a span of about 100,000 years. The fossils were found in Europe and parts of Western and Central Asia. Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat.Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension76" X54" X 40"

Supply & installation of ‘PROCONSUL(Chimpanzee)’ using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year.. The gadget to painted with quality PU coating after proper surface preparation.Concept: Chimpanzees are one of the two species of the genus Pan, the other being the bonobo. Together with gorillas, they are the only exclusively African species of great ape that are currently extant.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension54" X 22" X 20"

Supply & installation of ‘UINTATHERIUM’ using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year.. The gadget to painted with quality PU coating after proper surface preparation.Concept: Uintatherium lived during the early to middle Eocene period, about 45-40 million years ago. It was the largest, most spectacular, and most bizarre animal discovered in the Eocene deposits near Fort Bridger, Wyoming, USA.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary. Dimension 11'X 5.5' etc.

Supply & installation of ‘PSLV’ including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete.Specification : 25 feet height ,23 inch Dia. 25x25X6m.m Mild steel angle frame is installed to hold the rocketupright.

Supply & installation of ‘MINIATURE SQUARE WHEEL’ including fabrication, Painted with good quality PU coating with proper surfacepreparation , Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Total length 10 feet. width 3feet. Height - 3 feet. The property of SQAURE WHEEL CURVE is explained with mini cart moving on square wheelpath.

Designing, Supply & installation of ‘TAUTOCHRONE EFFECT' including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Length 6' width 3'

Supply & installation of ‘CYNOGNATHUS’using PCC 1:4:8 with necessary explanation board in Tamil & English ( each plate of A4 size) comprehensive A.M.C for 1 Year. . The gadget to painted with quality PU coating after proper surface preparation.Concept: Cynognathus lived between the lower Triassic to middle Triassic periods, about 240 million years ago.Specification: Fibre reinforced polymer model made up of good quality ISO naphthalene resin & FRP Roving mat or chopped stranded mat. Proper mixture of gel coat, catalyst, pigment, PVA are used for good quality bonding & for all weather proof surface. Steel reinforcement to be given wherever necessary.Dimension75" X 21" X 32"

Designing, Supply & installation of ‘TAUTOCHRONE EFFECT' including fabrication, Painted with good quality PU coating with proper surface preparation, Packing loading unloading transportation to site fitting, Commissioning, demonstration with explanation board in two language (English & Tamil) comprehensive A.M.C with spare parts for 1 Year with proper planning site visit & Design etc. complete. Length 6' width 3'

Moorthy (BID ID -1234431)