Various sanctioned works of MCMM Jabalpur under GE (East) Jabalpur (As per tender documents)

Amount

Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, and getting out in any type of soil including removal complete all as specified and directed

M&L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundations, filling mass concrete complete all as specified and directed.

M&L PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in foundations filling mass concrete complete all as specified and directed.

S&F mild steel angle as in posts/ struts in fencing including cutting, bending drilling holes, notching for wire etc, flat iron fillets for securing wire mess etc welding including all necessary drilling bolts or reveting etc conforming to Fe- 290 Gde E-165 etc complete all as specified and directed

Fixing only MS galvanised chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, binding wire etc complete all as specified and directed.

Supply only MS galvanised chain link fencing any type and any gauge complete all as specified and directed. Note : Weight of chain link fencing shall be assessed by BOO conveyed by GE.

S&F round bars for fixing of chain link fencing, in available length cut to shape, bent to shape required, including cranking, bending spirally for hooping etc. complete and Fe-410 W (Gde E-250 ) quality-A or Fe 290 (Gde- E -165) complete all as specified and directed.

M&L preparing new steel surfaces and applying two coat of synthetic enameled paint over a coat of red oxide primer exc 10 cm width or girth complete all as specified and directed.

Excavation in trenches nexc 1.50 mtr wide and n exc 1.50 mtr depth, for foundation etc nexc 10Sqm on plan and getting out in any type of soil complete all as specified and directed.

M&L RCC M-25 (Design Mix) by using 20 mm graded stone aggregate as in foundation , raft, footing, plinth beam, base for column etc complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished concrete surfaces complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete complete all as specified and directed

M&L RCC M-25 (Design Mix) (20 mm graded stone aggregate) as in column complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and directed.

M&L RCC M-25 (Design Mix) by using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.50 m complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs,floors slabs,landings and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

M&L RCC M-25 (20 mm graded stone aggregate) as in slabs suppoorted on walls,beams and column in floors, roof, landings, balconies, canopies, deck slab and in shelves the like complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 18 above but 8 mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed

M&L 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick surfaces in CM (1:4), first coat 10 mm thick plaster in CM 1:4 and second coat 5 mm thick in CM 1:4 with using water proofing liquid finished surfaces even and smooth without using extra cement complete all as specified and directed. Note : WPL shall be measured and paid seperately.

M&L 5mm thick rendering in CM (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L forming embarkment including raising (or lowering) earth spreading in layer n.exc 30 cm thick watering, ramming/rolling and finishing to required size and slope etc n.exc 1.5 mtr high from base complete all as specified and directed.

M&L broken stone or boulder hardcore of gauge n.exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L PCC 1:4:8 type D2, 75mm thick using 40mm graded stone aggregate as in sub base complete all as specified and directed.

S&F Non Skid Ceramic Tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F Glazed ceramic tiles (300x450)x 8-10 mm thick, in dado/ skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding laid over 20 mm thick screed bed in CM 1:4 quoted rates shall be including moulding and rounding complete all as specified and directed.

M&L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F vitreous china water closet squatting pan 'orissa pattern, ivory coloured of size 580 x 440 mm, with integral foot rest and outlet for 'P' or 'S' trap , WC pan shall be set in lean concrete below level of rim of pan to receive the floor finish complete all as specified and directed.

S&F PVC valveless syphonic action type flushing cistern 10 ltrs capacity low level, white with inlet ball valve, float and handle including brackets flush pipe of polythene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed.

S&F vitreous china white counter oval shape wash hand basin of size 630x450mm incl brackets complete all as specified and directed.

S&F 15 mm bore long neck CP pillar taps, fancy type, cast copper alloy with capstan heads screwed down high pressure with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F tubular towel rail 20 mm dia 'D' type 600mm long of stainless steel complete all as specified and directed.

S&F angle stop valves 15mm bore, fancy type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore PVC connection with PTMT nuts of length 450mm complete all as specified and directed.

S&F brass chromium plated bottle trap for wash basin/sink with inlet and outlet screwed for pipe or connections including necessary packing, union and cap bore of trap 32mm fixed complete all as specified and directed.

S&F waste coupling brass CP for glazed ware sink, WHB etc with long screwed shanks and fly nuts complete of 32mm dia.etc. complete all as specified and directed.

S&F 15mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified and directed.

S&F 20 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified and directed.

S&F 500 Ltrs capacity rotational moulded polythene water storage tank ISI marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 20mm bore ball brass valve, high pressure with polythene float & fly nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 20mm bore Gun metal gate valve with iron wheel head screwed both end for iron pipe complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubberring joints fixed to walls 75mm bore complete all as specified and directed.

S&F 110mm bore PVC (S.W.R) bend with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece, single `Y’ equal or un equal with access door complete all as specified and directed.

S&F 75mm bore PVC (S.W.R) bend with access door complete all as specified and directed.

S&F 110mm bore PVC vent cowl complete all as specified and directed.

S&F PVC floor trap 75 mm dia with CP gratings complete all as specified and directed.

S&F PVC nahani trap 110 mm dia with CP gratings complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting n.exc 10 cm girth in brick wall complete all as specified and directed.

S&F Solid PVC Double door frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick particle board (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm butt hinges extruded aluminum alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F 150 mm long aluminum anodized barred tower bolts of extruded section complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and directed.

S&F powder coated aluminium ventilator shutters, partly fixed and partly louvered type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed.

M&L rendering 10 mm thick on fair faces of concrete surface in CM 1:3 for receive the roof finishes with water proofing liquid complete all as specified and directed. Note : WPL shall be measured and paid separately

M&L APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by torched application complete all as specified and directed. Note : Four course roof treatment consists of as under :- (a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm. (b) Laying of APP based membrane as specified thickness and weight. (c) Applying two coat of aluminium paint @ 100ml/sqm.

Supply only liquid water proofing compound complete all as specified and directed.

M&L 75 mm thick Cement concrete type C2, 1:3:6 by using 40mm graded stone aggregate as in finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L Preparing new surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of distmper oil emulsion over a coat of primer and avg 3 mm thick wall care putty complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Returning, filling in, including spreading levelling watering and well ramming in layers n.exc 25cm as in hard/dense soil complete all as specified and directed.

Removing excavated material exc. 250 m but n.exc. 500 m and depositing where directed in hard/dense soil complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out soft/loose soil complete all as specified and directed

M&L sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L 60 mm thick glossy finish machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of M-35 grade complete all as specified and directed.

Excavating over areas, exc 1.5 m deep but n exc 3.00 m deep and getting out soft/loose soil complete all as specified and directed.

M&L 150mm dia reinforced cement concrete pipe CL NP-2 laid and jointed complete with collars complete all as specified and directed.

M&L PCC 1:4:8 type D2, 40mm graded agg as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 150 mm bore complete all as specified and directed.

M&L for brick bat loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

M&L Precast RCC (1:2:4) type B1 by using 20mm graded stone aggregate as in cover slabs of manholes, open drains inclusive of form work set in CM (1:4) complete all as specified and directed. Note : Reinforcement shall be measured and paid separately

M&L RCC nominal mix 1:2:4 by using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like cpmplete all as specified and directed.

M&L brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L PCC 1:2:4 type B2 using 40mm graded stone aggregte as in surface channels & drain complete all as specified and directed.

M&L providing PCC (1:24) type B1 using 20 mm graded agg as in coping/Channel of drain etc complete all as specified and directed.

Removing excavated material to a distance n exc 50 mtr and depositing where directed at a level n.exc 1.50 mtr above the starting point complete all as specified and directed.

S&F cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, 75mm bore, confirming to IS 3989 complete all as specified and directed.

S&F 75 mm dia cast iron cowls complete all as specified and directed.

M&L anti-termite Treatment of soil under floors using emulsion @ one litre per litre per hole, 300mm apart incl drilling and plugging 12 mm dia holes with CM 1:2 to match the floors complete all as specified and directed.

M&L for anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @2.25 litres per linear meter incl drilling and plugging holes etc.in apron complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite rates are including rounding and moulding complete all as specified and directed.

S&F vitreous china water closet, wall hung pattern of size 515mm x 355mm x 365mm, white in colour with UF seat cover including slim concealed cistern with floor mounting frame, installation kit and drain pipe connection set and control plate Moon Design all chrome with all accessories complete all as specified and directed.

S&F vitreous china urinal, Half stall type white, with grating and union etc complete all as specified and directed.

S&F long neck chromium plated brass pressmatic pillar tap of suitable size with necessary fixing arrangements incl making hole over concrete surface as approved by Engr-in-Charge complete all as specified and directed.

S&F chromium plated brass pressmatic urinal push cock with necessary fixing arrangements incl urinal spreader of suitable size as approved by Engr-in-Charge complete all as specified and directed.

S&F brass chromium plated, 15 mm bore health faucet, (flexy type) min 1.00 mtr long complete all as specified and as directed.

S&F brass chromimum plated two way bib cock fancy type, 15mm bore complete all as specified and directed.

S&F 1000 Ltrs capacity rotational moulded polythene water storage tank ISI marks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F toilet paper holder fixed to walls with brass chromium plated (CP) brass screws complete all as specified and directed.

M&L RCC 1:2:4 nominal mix (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including provision of 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as above item No 20.00 as per item including provision of 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with lugs steel handles and steel peg stays, with glazing bars, devetailed or welded complete all as specified and directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with lugs steel handles and steel peg stays, without glazing bars, devetailed or welded complete all as specified and directed.

M&L framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L Sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5 sqm in each pane 3 mm thick complete all as specified and directed.

S&F 125X60 mm size of Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

M&L plain cement concrete Type C1, 1:3:6 (using 20 mm graded stone aggregate) for filling of hollow pressed steel frame complete all as specified and directed.

M&L plain cement concrete Type B-0 1:2:4 (using 12.5 mm graded stone aggregates) for fixing hold fast including repairing of disturbed plaster (while taking down door/window,ventilator frame) and matching the repaired surface with existing one complete all as specified and directed.

S&F 25 x 3mm FI hold fast conforming to Fe 290, Gde -E-165 complete all as specified and directed.

S&F 35mm thick second class hardwood factory made flush door shutters, solid, core construction with black board core and plywood face panals commercial type on both sides complete all as specified and directed.

S&F 35 mm thick second class hardwood factory made glazed and skelton shutters open rebated and prepared to receive glass gauge etc. wihout sash bars sizes of the members of the shutters as specified in SSR Part-I section 8 , clause 8.24 (a) complete all as specified and directed.

S&F Aluminium door stopper of size 150 mm long double legged fixed to bottom rail of door shutter provided with rubber bushing at one end to stop the door at floor and other end provided with aluminium plate base fixed with door shutter with screws at appropriate height complete all as specified and directed.

S&F MS 300mm helical door springs including roller and roller plate complete all as specified and directed.

M&L for Preparation of new or previously un treated wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and directed for the following :-

One light point/ Exhaust Point controlled by one switch.

One 3 pin switch socket outlet point 5 Amps on independent board.

One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item No 116 above but with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed.

S&F modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

S&F modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

S&F modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

S&F modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite, three terminal complete all as specified and directed.

S&F LED light fitting 1 x 20Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrangenment complete all as specified and directed. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 10 watts 220 volts AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fix energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed.

S&F sheet metal enclosure distribution board SPN 4 way 240 volts with IP 43 protection and double door, bus bar rating 100 Amps, suitable for mounting MCBs complete all as specified and directed..

S&F MCB, single pole & neutral, 240 volts, 32 to 63 Amps, complete all as specified and directed.

S&F MCB, single pole, 240 volts, 6 to 32 Amps, complete all as specified and directed.

S&F exhaust fan, steel body AC single phase. 230 V of size 300 mm sweep with, blades, frame and louvers and including making of holes in wall, floor etc complete all as specified and directed..

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length fo drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 2 core cable complete all as specified and directed.

M&L for cutting of bituminous road / floor / culvert / PCC hard standing for laying of pipe / cables not exceeding 1.5 meter wide and not exceeding 1.5 meter deep including refilling / with material and , watering well ramming / compacting and making good with PCC 1;2;4,type B-1, 100 mm thick complete all as specified and directed.

Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specified and directed. Note : Thickness after punning shall be measured.

M&L unreinforced precasted concrete cable cover class LV, type 1,flat , size 250mm x 150mm x 40mm complete all as specified and directed.

M&L GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specified and directed.

M & L cutting of existing cast iron / GI pipe in position for insetion of CI specials or GI Fittings viz Tee, collar, bend or tail piece etc 80 to 200 mm bore pipe including removing of blockege, cleaning of pipe line complete all as specified and directed.

S&F steel tubing galvanized medium grade with all fitting laid in trenches /Walls/Ceiling/ Floor of size 25 mm dia complete all as specified and directed.

S&F Gun metal globe or gate valves of size 25 mm with iron wheel head , screwed both ends for iron pipe and fixed complete all as specified and directed.

Schedule of credit amount of Rs. NIL to be deducted during AOC.

RAM ASSOCIATES (BID ID -3355416)

ANAMIKA CONSTRUCTION (BID ID -3363629)