RENEWAL/REPLACEMENT OF FURNITURE AGAINST CONDEMNATION FOR THE QE MAR AND JUN 2019 GE JAIPUR AT JAIPUR MIL STN

Amount

Bench workshop (FD-1024) (a) All as shown on drawing. (b) Overall size shall be 1500mm long, 900mm wide and 760mm high, four legs shall be of 32mm squar mild steel tube of wall thickness 1.6mm. Size of steel frame shall be 1400mmx800mmx720mm. Leg shall be of 720mm high. Top of legs shall be joint together in long sides and short side with 32mm squar mild steel tube of wall thickness 1.6mm as top rail in long and short sides. Two shorts stiffners joining legs in short side at 100mm from bottom of legs shall be provided with 32mm squar mild steel tube of wall thickness 1.6mm. One long stiffner joining short stiffner in middle at 100mm from bottom shall be provided with 32mm squar mil steel tube of wall thickness 1.6mm. A drwaer shall be provided at right hand side of table with locking arrangement. All steel surfaces exposed to view when placed in position shall be given two coats of enamelled paints over a coat of primer with sprey macine after preparation of surfaces. All wood surfaces exposed to view when placed in position shall be given two coats of oil paints over a coat of primer with sprey macinea fter preparation of surfaces.

Chair Dining (FD/MAP-II/04) (a) TIMBER:- All wood work shall be of first grade kiln (plant) seasoned teak wood free from knots & cracks. (b) CUSHION:- Seat & back shall be 50mm thick synthetic foam of 20 density fixed over wooden frame and it shall be covered with leatherised rexine of approved, texture and quality. (c) POLISH:- All wood work and teak veneered surfaces shall be French polished except where painting is indicated in drawings.

Chair easy (FD-229) (a) TIMBER : All wood work shall be of first class hard wood (MP teak). (b) CANE : Caning shall be with 2.0 mm wide and 0.4 mm thick plastic cane half round of superior quality white or cream colour woven to the pattern all as shown on drawing and as approved by the Engineer-in-Charge (Godrej pattern). Strengthening band shall be of 3.5mm wide plastic cane. (c) RING : Hard PVC rings shall be screwed to legs. (d) POLISH: All exposed surfaces of timber shall be french polished. (e) REST : All as shown on drawings.

Chair Computer (FD/06/MAP/01) Specification shall be all as per shown in drawings and as directed by Engineer-in-charge. Make : Model No. MMPL/70011/HB/A of Durian or equivalent as approved by GE

Receptacle Large (FD-1044) THIS DRAWING SUPERSEDES DRAWING NO FD-226(M) SHEET 1/1 All as shown on drawing. Overall size shall be 330mm dia and 405mm high. The body of receptacles small shall be of 1mm dia galvanized iron circular sheet of 300mm dia. Bottom of circular sheet body shall have 19mmx4mm flat iron band welded to 1mm thick GI circular sheet. 75mmx40mm made to shape of 3mm thick flat iron welded to 25mmx4mm flat iron lever, hinged at other end with 3mm dia pin to hold 25mmx4mm flat iron vertical lever. The fulcrum of bottom lever shall be in the center of circular bin and supported by 6mm dia loose rivet fixed in the center of 25mmx3mm flat iron welded to circular GI sheet in center. The top of vertical lever shall support the mild steel reinforcement sheet made out of 150mmx75mm3mm thick welded to cover with 3mm dia pin to enable the cover to open upwards when the pressure shall be applied at foot rest. The top cover shall be of 1mm thick GI sheet cover 330mm dia ends bent inside over 3mm dia wire al-round the cover. Two numbers bracket made to shape out of 3mm thick mild steel sheet shall be provided to GI sheet of receptacle at top for holding 6mm dia pin over which mild steel reinforcement sheet welded to cover enables the cover to open. Bin shall be cylindrical closed at bottom and of 290mm dia and 315mm high made of 1mm thick GI sheet. Two brackets of 50mmx65mmx3mm thick shall be provided to bin for holding 10mm dia mild steel bar handle. 40mmx3mm mild steel flat iron ring shall be provided at the bottom of bin. 10mm dia mild steel bar handle shall be provided to bucket which shall be made of 1mm thick GI sheet and size all as per drawing. All steel surfaces, except galvanized iron surfaces, shall be given two coats of aluminium paint over a coat of primer after preparation of surface.

Table 900x600x760mm wooden (FD-227) (a) TIMBER : All wood work shall be of first class hard wood (Teak). (b) PARTICLE BOARD : Table top shall be 18/19mm thick three layered flat pressed, pre-laminated particle board one side decorated teak finish & other side plain lamination white, exterior grade (ISI marked). (c) DRAWER : 6mm thick ply commercial face both side shall be provided at bottom of drawer and all as shown on drawings and directed by E-I-C. (d) POLISH : All wood work and teak veneered surfaces shall be french polished. (e) EDGING : 4mm thick teak wood edging alround table top shall be provided. (f) RING : Hard rubber rings shall be screwed to the legs. (g) REST : All as per drawings

Rack side with tray (a) SHEET : 1.00 mm (nominal) thick MS sheet shall be provided. (b) ANGLE IRON : 40 X 40 X 3mm angle iron shall be provided for leg. (c) PAINT : All welded construction and steel work shall be painted with two coats of synthetic enamel of approved shads over a coat of red oxide primer. (d) REST : All as per drawings.

Chair Writing (MAP) (a) FRAME: Frame shall be made out of 25mm x 10mm section MS tubular frame cantilever type powder coated. (b) HAND RESTS : One piece arm rest made of black integral skin polyurethane with 75-85 shore ‘A’ hardness and reinforced with MS insert. It shall be scratch & weather resistant. Both hand-rest sections shall have slope towards front. (c) FOAM: Polyurethane foam shall be 50mm thick and shall be moulded with density 50-55 Kg per cubic metre and hardness 20 ± 2 Kg on hampden machine. Back foam shall be designed with contoured lumber support for extra comfort and 12mm hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVS lipping all around. (d) FABRIC : Fabric shall be contained the following material in various colours Arcylic, Polyester, Poly Propylene and shall be as approved by GE. (e) STOPPER: Four numbers of rubber stoppers shall be provided at bottom of the chair. (f) REST : All other items / fittings shall be as shown on drawing and provided as per relevant IS and trade engineering norms / pattern.

Classis Sofa Set 3 Seater : (TP) Supply classic sofa set of 3 seater leatherette of approved colour. The sofa stands firm on solid PVC legs with thick armrests, slightly curved on the front face of the sofa complete all as specified and directed. Make : Model No. BERRY/ 55003 /A/3 of Durian or Model No. ELITE SOFA 3 Seater of Godrej or equivalent as approved by GE

Peg Table (FD-277) (a) TIMBER:- All wood work shall be of first class hard wood (teak). (b) EDGING: Irrespective of what is shown on drawings, 4mm thick teak wood edging all round to table top shall be provided. (c) TOP: :- Table top shall be 18/19 mm thick three layered flat pressed teak wood pre-laminated particle board exterior grade (ISI marked). (d) REST: All as shown on drawings.

Sofa Set 2 Seater (FD-281) (a) TIMBER : All wood work shall be of first class hard wood (Teak). (b) PLY : 6mm thick commercial plywood, BWR quality shall be provided in seat & back of sofa above bottom wooden bearers though the same is not shown on drawings (c) CUSHION : 100mm thick cushion foam for seat & back cushion shall be provided. Irrespective of what is shown /specified else where in the tender documents, foam with 40 density, ISI marked shall be used in the work. (d) TAPESTRY CLOTH : Seat and back foam shall be covered with approved standard tapestry cloth rate not less than Rs. 300 per running metre (e) POLISH : All wood work surfaces shall be french polished. (f) REST : All as shown on drawings.

Table bed side (FD/E6/MAP/15) (a) FRAME : Frame shall be as shown on drawing. Tube shall be of 18mm Square MS pipe having wall thickness of 18 gauge. (b) TOP/SIDES/BACK: Top, side and upper part of back shall be 18/19 mm thick melamine faced pre-laminated particle board bonded with phenol formaldehyde as per IS- 3087-1985 exterior grade BWR type and shall be ISI marking on the edges. Exposed edges of board shall be covered with 4mm thick teak wood beading all-round as directed by GE. (c) DRAWERS : Bottom of drawers & back of table shall be 6mm commercial plywood which shall act as bottom of table. Sides and back of drawers shall be made with 12mm thick BWR grade commercial ply wood. Drawer shall be provided with telescopic channel and stainless steel handle as approved by GE in writing. (d) FINISHES : All exposed wooden surfaces of timber and teak veneered surfaces shall be French polished. Steel surface shall be black powder coated. (e) REST : As shown on drawing and provided as per relevant IS and trade engineering norms/pattern.

Charpoy IP with Hard Top w/o MNF set (FD/MAP-II/01) (a) MS TUBE LEGS: MS tube legs shall be 32mm x 32mm rectangular MS pipe (16 gauge). (b) TOP : Top shall be 12 mm thick BWR phenol bonded Ply (unpolished) placed on top of 25 x 25mm MS pipe (16 gauge) supports equal distance in line with bottom of 25mm x 65mm section. (c) STIFFENERS & SUPPORTS : Stiffeners & supports shall be 25mm x 25mm (16 gauge) all as shown on drgs. (d) FRAME : Frame work (long & short rails) of 25mm x 65mm MS rectangular pipe (16 gauge). (d) Bending, welting, riveting, welding, lapping, turning and other items / fittings as required shall be done / provided as specified in relevant IS and as per trade norms and pattern and as directed by the GE. (e) TOE : MS plate 32x32x5mm shall be welded at bottom of legs and under which 3mm thick rubber sheet shall be fixed with adhesive. (f) FINISHES: The steel members shall be powder coated. (g) REST: All as shown on drawing and provided as per relevant IS and trade engineering norms / pattern.

Chair school with hand rest (FD/E6MAP/05) a) TIMBER. All wood works shall be of first class hoar wood (teak) (b) TUBE. Frame shall be 25mm dia MS conduit pipe of wall thickness 1.6mm thick. (c) CANE : Caning shall be with 2.0 mm wide and 0.4 mm thick plastic cane half round of superior quality white or cream colour woven to the pattern all as shown on drawing and as approved by the Engineer-in-Charge (Godrej pattern). Strengthening band shall be of 3.5mm wide plastic cane. (d) ARMS. Arms shall be of MS tube as of frame bent to shape covered with teak wood Hand Rest all as shown on drg and directed. (e) RING : Hard PVC rings shall be screwed to legs. (f) POLISH/PAINTING : All wooden surfaces shall be painted with three coats of black polish and all steel work shall be painted with two coat of synthetic enamel paint spray olive green paint over a coat of red oxide primer. (g) TOES. Hard PVC toes shall be provided at bottom of legs and two Nos PVC caps shall be provided to tube frame. (h) REST : All as per drawings.

Chair Dining in lieu of Chair WB (FD-279) (a) TIMBER:- All wood work shall be of first grade kiln (plant) seasoned teak wood free from knots & cracks. (b) CUSHION:- Seat & back shall be 50mm thick synthetic foam of 20 density fixed over wooden frame and it shall be covered with leatherised rexine of approved, texture and quality. (c) POLISH:- All wood work and teak veneered surfaces shall be French polished except where painting is indicated in drawings.

Receptacle PVC (FD/E6/MAP/13) (a) RECEPTACLE : Plastic container with lid shall be of thick polymer plastic of best quality. Colour of container shall be bright i.e red / green / blue as approved by GE. Handles of container shall be of best quality. Capacity of the receptacle shall be 20 Litrs. (b) All other details shall be as shown on drawing. Make – Blowplast / Supreme / Cello / Polyset / Bright or equivalnet as approved by GE

Rack Pigen Hole (FD-1037) (a) Angle Iron Frame: 40 x40x4 mm angle iron shall be provided for frame of rack. (b) Sheet: 1.00mm nominal tick MS sheet shall be provided for back, side, top, bottom and shelves. (c) Paint: Two coats of synthetic enamel olive green paint over a coat of red oxide primer shall be provided to all external & internal steel surfaces. (d) Rest: All as per drawing

Box Kit Steel (FD-98M) (FD-98M) Supply steel Box kit of overall size shall be 760mm long, 405mm wide and 312mm high comprises of following specification: (a) SHEET: Plain black iron sheet of 22 gauge shall be provided at top bottom sides, shelf and stiffeners and for base, angles and corners 16 gauge plain black iron sheet shall be used. (b) HANDLE: Drawer shall be provided with standard PVC recessed handle and locking arrangement as shown on drawing. (c) HASP AND STAPLE: Mild steel safely type, stove enamelled 100mm size one number shall be provided as decided by Engineer-in-Charge. (d) FINISHES: Painting to steel surface with two coat of synthetic enamel black paint over a coat of red oxide. Zinc chrome primer. (e) Rest all as per drawings as directed by Engineer-in-charge.

Hot food trolly (FD-133 M) All as shown on drawing. Overall size shall be 1385mm long, 740mm wide and (aporox) 940mm high (approx) All sheet, tubular handles etc shall be of anodized aluminium sheet body. Tubular of 1250 volts, 230/AC/DC wattage shall be provided as shown on drawing and as directed by Engineer-in-charge. Two lower compartments with receding doors and moveable refrigerator type racks shall be provided as shown on drawing and as directed by Engineer-in-charge. Multi-stage rotary switch for heat control shall be provided as directed by Engineer-in-charge. Heating chamber shall be insulated with glass wool. Stainless steel food vessel of 200mm dia wide and 200mm deep with dud setting lids shall be provided. Heavy-duty ball bearing type 200mm dia rubber wheel collapsible front counter shall be 390mm long and 500mm wide as shown on drawing.

Table Writing (FD275) (a)TIMBER: - All wood work shall be of first class hard wood (MP Teak). (b) Teak wood stiffener of size 50 x 25mm shall be provided to strengthen the joints at corners of legs with other members. (c)TOP: - :- Table top shall be 18/19 mm thick three layered flat pressed teak wood pre-laminated particle board exterior grade (ISI marked). (d) RING: - Hard rubber / PVC toes 25mm dia & 25mm high shall be screwed to legs. (e) POLISH: - All wooden surfaces exposed to view where placed in position shall be French polished with high gloss finish. (f) FITTINGS : (i) Brass piano type hinges shall be fixed with wood (brass) screws for fixing shutter. (ii) KNOBS: Knobs shall be of aluminum anodized (dark brown) fixed with brass screws of suitable size. (iii) LOCKS : Locks shall 50mm long of brass Godrej/Haraison (iv) BALL CATCHER: Ball catcher shall be fixed on top and bottom of the shutter. (g) REST: - All as shown on drawings.

Stool Steel 305x305x510 (FD-81M) a) Sheet : 1.6 mm thick MS sheet shall be provided as shown on drawings and as directed by Engineer-in-Charge (b) Painting : 2 coat of synthetic enamel paint of approved colour over one coat of red oxide primer shall be provided on steel surfaces. (c) Rest : All as shown on drawing.

Stool Dressing CB with Cushion (FD/E6/MAP/14) a) TIMBER : All wood work shall be of first class hard wood (Teak). (b) PLY : 12mm thick commercial plywood, BWR quality shall be provided in seat & back of sofa above bottom wooden bearers though the same is not shown on drawings (c) CUSHION : 75mm thick cushion foam for seat cushion shall be provided. Irrespective of what is shown /specified else where in the tender documents, foam with 40 density, ISI marked shall be used in the work. (d) LETHERITE CLOTH : Seat foam shall be covered with approved standard Letherite cloth rate not less than Rs. 350 per running metre (e) POLISH : All wood work surfaces shall be french polished. (f) REST : All as shown on drawings.

Peg Table (FD-277) (a) TIMBER:- All wood work shall be of first class hard wood (teak). (b) EDGING: Irrespective of what is shown on drawings, 4mm thick teak wood edging all round to table top shall be provided.

Table Dinning 8 Per (FD-376) (a) TIMBER:- All wood work shall be of first class hard wood (Teak). (b) EDGING :-irrespective of what is shown on drawings, 4mm thick teak wood edging around to table top shall be provided. (c) TOP:- Table top shall be 18/19 mm thick three layered flat pressed teak wood pre-laminated particle board exterior grade (ISI marked). (d) RING:- Hard PVC rings shall be screwed to legs. (e) POLISH:- All exposed surfaces of timber shall be French polished. (f) REST:- All as per drawings.

M/S Shri Balaji Enterprises

B.S Constructions

C.P.Computers

Apsara Industries