GEK-66/2021-22

Amount

Schedule 'A' Section - I

Demolition of cement concrete (unreinforced)Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engr-In- Charge.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engr-In- Charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position framed work complete all as spd. complete all as specified and as directed by Engr-In- Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed by Engr-In- Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling of cast iron 100mm or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed by Engr-In- Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed by Engr-In- Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-In- Charge.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as spd and as directed by Engr-In- Charge.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as spd and as directed by Engr-In- Charge.

Taking down chowkats or frames with shutters (without taking off shutters) exceeding 1.5sq.m and not exc 4.00sq.m each of any description incl making good the disturbed surfaces complete all as specified & directed by Engr-In- Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified & directed by Engr-In- Charge.

Material & Labour brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified & directed.

M & L 2nd class HW clean Sawn timber framed and fixed scantling/posts complete all as specified & directed by Engr-In- Charge.

M & L for 20mm thick boarding / planks of 2nd class hard wood planed both sides fixed with nails in any situation and treating with creosote complete all as specified.

Material and labour for false ceiling with one layer of 'LaGyp' standard boards manufactures by M/S Lafarge Board Gypsum India Pvt Ltd, at all height and levels. Standard boards of size 1220x1830x12.5mm, standard board to be laid on 'LaGyp' universal channel (web 45 mm premanunfacturers specifications metal comprising of "LaGyp" universal channel (web 45 mm and flange 27mm base metal thickness (BMT) 0.55 mm and length 3660 mm to be used as main channel as well as ceiling channel. "LaGyp" connecting clips, perimeter channel ( Size of web 28 mm, flange 18/30 mm and length 3660 mm, MBT 0.55 mm) and "L" angle (Lenght 3050 mm BMT 0.55 mm) with finally the board are to be Jinded and finished so as to have a flush look with which includes filling and finishing the tepered and square edges of the board with "LaGyp" easy joint Gypsum based jointing compound, "LaGyp" paper tape. The rate should include providing and laying two or more coats of oil bound distemper to give a neat and even finish including preparing the base with primor and scaffolding etc complete in all respect complete all as specified and as directed by Engr-In-Charge

M&L for Anti termite treatment at point of contact of wood work by chemical emulsion (in oil or kerosene based solution) @0.5 ltrs/hole by drilling 6 mm dia holes at a downward angle 45 degree at 150 mm centre to centre and sealing the same complete all as specified.

Material & labour for 15mm thick rendering in cement mortar 1:4 over fair faces of brick masonry surfaces or concrete surfaces finished even and smooth without using extra cement complete all as specified.

M&L rendeing 10mm thick other then fair faces surfaces in CM 1:6 finished even and smooth with out using extra cement (Internal surfaces)

M & L RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified.

PCC (1:3:6) type C2 using 40mm graded agg as in surface channel / drains.

Extra for forming fair finished drain or channel 60 cm inner girth in forms, moulds/stopped ends etc.

M & L MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F strudctural steel MS angle, channel, flat iron etc, as in roof trusses, purlins , posts etc. including distance pieces etc conforming to Fe-410-W (Gde-E-250)Quality -B complete all as spd.

Preparation new steel and iron surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified.

Supply and fixing Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Supply and fixing Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (squre/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointted in white or coloured cement to match with screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

M&L for coloured glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm /450 x 350 x 7 mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendring in 1:4 cement mortar complete all as specified & as directed

M & L Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

M & L Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in scarting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendring in 1:4 cement mortar complete all as specified & as directed

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including 15mm thick Screadbed in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Material and labour for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 32 above and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

Grinding and Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed.

Pressed steel frames for doors of size 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed

Pressed steel frames for doors of size 105 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed

S&F steel windows with side hung shutters including projecting type hinges with steel handle , and steel peg stay , complete with glazing bars , dovetailed or welded complete all as specified & diretced

-Ditto- all as per Srl Item No. 37.00 but without glazing bars

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings , framework of water tanks and similar work conforming to Fe 290 Gde E-165

Supply only galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specifeid

Supply only sheet glass , ordinary quality & glazing 3mm thick, with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as diretced

Supply only figured glass 4mm thick, pin head type and glazing with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as diretced

Supply and fixing Factory made plain, framed, panelled shutters , 35mm thick of 2nd class hard wood (Hollock) with lock rail and panels of 9mm thick commercial ply or 12mm thick vaneered particle board with commercial veneered on both sides, incl priming coat, duly hammer marked. The size of rail & style shall be as per IS 1003 part-1 kiln seasoned and chemically pressure treated incl one coat of pink primer complete all as specified & directed.

Supply and fixing glazed and gauged skeleton shutters (factory made) 30mm thick, 2nd class hard wood 'Hollock' open rebated and prepared to receive glass, gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc incl priming coat. The size of member of shutters as spfd in SSR Part-1 Section 8 clause 8.20 (a) incl kiln seasoned and chemically pressure treated, complete all as specified & directed. Note :- (i) Wooden beading/glazing clip shall be supplied alongwith the shutters. (ii) Glass and wire mesh shall be measured and paid for separately as 'Supplied only' rate under respective item of this schedule.

Mild Steel works as in bends straps, hold fasts etc, conforming to IS-2062 (Fe-165), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with mS square tube etc complete all specified.

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2.4 (or) 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethen painted on the front face and 2mm plain colur PVC sheet on back face with particle board core etc complete all specified & as directed .

S & F in repairs curtain rails anodised aluminium alloy with fixing brackets etc complete all as specified

Supply and fixing 2nd class hard wood small fittings such as brackets of any type latch and hinges blocks shaped door and windows stops and the like, including all necessary labour, articles n.exc. 200 cucm each complete all as specified & directed.

Supply and fixing Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 200 mm complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 150 mm complete all as specified & directed.

Supply and fixing aluminium fabricated type extruded handles of size 125 mm complete all as specified & directed.

Supply and fixing 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

M&L for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl washing, rubbing down and stoping the connected previously treated surfaces and applying two coats of oil emulsion distemper (tint as approved by GE) complete all as specified & directed.

M&L for preparation of plastered or unplastered new surfaces of walls and applying two coat of oil emulsion distemper (tint as approved by GE) including one coat of primer complete all as specified.

M&L for preparation of plastered or unplastered old decorated surfaces of walls incl cornices, chajjas, sun shades etc. and applying two coat of cement base paint (1st quality) with and incl curing the surfaces and curing the same after application of cement base paint (tint as approved by GE) including complete removal of existing surface with sand paper or iron patti / flat complete all as specified.

Material & labour for preparation of old painted wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified & directed.

M & L including preparing old painted NTP/CGI/PGI or other steel roof surfaces of any type of treatment surfaces incl washing and cleaning etc. to steel and iron surfaces and applying one coats of synthetic enamel roof paint complete all as specified.

Material & labour for preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint (1st quality) complete all as specified & directed.

Supply & fixing in repairs pre-laminated particle board 19mm thick, interior grade pre laminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed as in repairs complete all as specified and directed by Engineer-in-Charge.

Material & labour piano hings, mild steel bright finish width of flap 30mm fixed in repair including taking out the existing complete all as specified and directed by Engineer-in-Charge.

Supply & fixing magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed as in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 40mm dia cupboard knob of brass, polished, fixed with nut screw and washer, fixed as in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fixing aluminium hook and eye anodised 150mm size fixed as in repairs complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm dia steel tubing and connection and removal from site

- Ditto- all as per Srl Item No. 67.00 but 20mm dia

S&F steel water tubing medium grade galvanized with all fittings and fixed complete to walls andceiling or laid into floor or 15mm bore complete all as spd.

-ditto- all as per Srl Item No. 69.00 but bore of pipe 20mm

Taking up or down steel tubing and connections cleaning for refixing and refixing oldsteel tubing and connections in new or in old position (walls cediling floor etc) of 20mm bore of pipe complete all as specifie

-ditto- all as per Srl Item No. 71.00 but 15mm bore

S & F in repairs 15mm bib tap cast copper aloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F in repairs viterous china WHB (flat back or angle back) any size, including cutting for and pinning in ends of brackets complete with waste pipe and all fittings complete all as specified.

S&F in repairs Vitreous China wash down water colset (Squat pattern) white complete as fixed in repair excluding flushing cistern and flush pipe "Orissa" pattern size 580x400 with integral footrest inject connection to trap antisyphonage etc complete incl joint between flushing pipe and socket of WC.

S & F in repair 15mm pillar tap cast copper aloy with capston heads chromium plated screwed down fly nuts screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F in repairs brass chromium plated tubler towel rail complete all as spd.

Dismantling water tanks exc 500 & nexc 1000 ltrs cap and removing to store complete all as spd.

S&F 1000 ltr cap ratational moulded polythene water stoarage tanks ( clyndrical vertical with closed top) hoisted and fixed in position complete all as spd.

S & F in repair 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified.

S&F in repairs of flushing cistern PVC 10 ltrs cap valve less syphonic action type, low level white with intel , ball valve , float incl brackets and PVC flush pipe 32mm dia complete all as specified. .

Supply and fixing angle stop valve, chromium plated, brass fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Supply and fixing 15mm dia PVC connection with brass nut, of length 450mm, in repair complete all as specified and directed.

S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch of butterfly handle scewed both ends for iton pipe or for unioin fixed complete all as specified

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as required complete all as specified.

S&F 75mm dia PVC (SWR) floor trap.

S&F 75mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) vent cowl

S&F 110mm dia PVC (SWR) "P" trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S & F in repair chromium plated shower rose (125mm) with swivel joints fixed to steel pipe or union complete all as specified and directed.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply fix in repairs Vitreous China urinals, half stall type ,complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S & F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws 160x160x90mm

Material & Labour for 50mm thick plain cement concrete C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as spd & directed. Note:- The plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item.

M&L cement concrete 50mm thick type B-2 , 1:2:4 (40 mm graded aggregate) complete all as specified & as directed

Dismentling of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

M & L for 18-20mm granite (any telephonic balck) work (table rubbed and polished) for Kitchen slabs, cooking platforms and counter for WHB and shelves with side ends of corners chamfered / nosed to required angle, laid over 15mm thick cement screed bed in CM (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite-including grinding of exposed edges .

M&L 100 mm thick cement concrete type C-2, 1:3:6 (20 mm graded stone aggregate) as in sub floors, filling and mass concrete etc

M&L screed bed or bedding layer of cement mortar (1:4) 15mm thick for laying floor finishes/pavers complete all as specified and as directed.

Coloured Chequred cement conc tiles (30cmx30cmx25mm thick) in grey cement and with pigment in floors etc , set and jointed in neat cement slurry, ocomplete all as specified and directed.

Dismantling 100 mm PVC drain or vent pipe of any description in any position including bends branch pieces etc.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

Material & Labour for Plain Cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in pressed steel frame and the like finished fair and even incl necessary form work complete all as specified & directed.

Material & Labour for 50mm thick plain cement concrete C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as spd & directed. Note:- The plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item.

Extra for forming fair finished drain or channel 30 cm inner girth in forms, moulds/stopped ends etc.

S&F Hand rails ,half round or other steel section or core for wooden hand -rail straight portion drilled and countersunk for balusters running bars for doors, balusters, noising to steps including embeding in concrete and screwing etc, wind ties for roof including securing boilts, post and struts in fencing including cutting tops to shape as directed,drilling holes , notching for wires, etc flat iron fillets(for securing wire mess etc, including all necessary drilling ,bolting or riveting etc, and similar works comforming to Fe-290 gde E- 165 complete all as sepcified and as directed.

S&F collapsible steel gates,top hugs,consisting of channel pickets,pivotedflat bars,top and bottom runners brass handles etc, as specified errected in position and securing runners with holdfasts and brackets complete all as specified and as directed.

M & L Non Skid coloured ceramic tiles 8 mm thick area exc 0.18sqm n exec 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles incl. 15mm thick screed bed or bedding layer in C.M 1:4 etc complete all as specified & as directed

All the same as per here-in-above but ceramic tiles of size on vertical surfaces such as skirting set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles incl. rendering 10mm thick in C.M 1:3 on brick work or concrete surfaces etc. complete all as specified & as directed

M&L for first quality joint free Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:4) complete all as spd & as directed.

Supply and fixing aluminium anodised powder coated frames for doors, windows with one or more rebates including joining cleats for fixing etc complete all as specified

S& F Anodised aluminium powder coated of any colour (Thickness or powder coating not less than 50 micron) door shutters, aluminium section weighing 0.55 kg/m includingnecessary joining cleats ,glazing clips, rubber neoprene packing, handles 2 nos in each door, hings anodised aluminium snap bedding screwa etc complete all as specified.

Supply and fixing aluminium anodised powder coated window and ventilator shutters fixed type with out sash bar aluminium weighing 0.55kg/m including necessary joining cleats glazing cleaps rubber packing anodised aluminium snap beading screw including anodised aluminium fitting such as peg stay 150mm long 1 No Hings type B-21 100mm long 2 Nos suitable handle 1 No etc complete all as specified

S&F sheet glass ordinary quality 4.8mm thick squares etc 0.50mm Sqm in each pane complete all as specified

Material and labour for door closer hydraulically regulated Aluminium (die cast) body, designation No 3, universal type, suitable for door shutters of weight between 61 to 80 Kg complete all as specifed & as directed

S&F double action floor spring hydraulically operated made up of miniumum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty.

Supply and fixing 200 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

M&L for preparation of plastered or unplastered new surfaces of walls and applying two coat of oil emulsion distemper (tint as approved by GE) including one coat of primer complete all as specified.

M&L for preparation of plastered or unplastered old decorated surfaces with sand papering of walls incl cornices etc. incl washing, rubbing down and stoping the connected previously treated surfaces and applying one coat of teraccota complete all as specified and as directed..

M & L Preparation of new or previously untreated surfaces of wood or based materials of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S & F in repairs 15mm bib tap cast copper aloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F in repairsVitreous Cliina wash basin, wliile, flat back, size 580x450irun (for Hospilal use) excluding taps,waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S & F in repair 15mm pillar tap fancy type cast copper aloy with capston heads chromium plated screwed down fly nuts screwed for iron pipe or for brass ferrule and fixed complete all as specified.

Dismantling water tanks n.exc 500 ltrs cap and removing to store complete all as spd.

S&F 500 ltr cap ratational moulded polythene water stoarage tanks ( clyndrical vertical with closed top) hoisted and fixed in position complete all as spd.

S & F in repair 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified.

S&F in repairs of flushing cistern PVC 10 ltrs cap valve less syphonic action type, low level white with intel , ball valve , float incl brackets and PVC flush pipe 32mm dia complete all as specified. .

Supply and fixing angle stop valve, chromium plated, brass fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

S & F in repairs vitreous china squatting pan of pattern, "long pan Pattern" size 580mm white with P or S trap front or back inlet and foot rests any pattern (excluding flushing cistern and flush pipe complete all as specified

S&F glass self assembly consisting of 5.5 mm thick sheet glass self 12mm wide with chromium plated brackets guard and railing 60 cm long

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engr-In- Charge.

S & F Toilet paper holder ,vitreous china box type

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and as directed by Engr-In- Charge.

Supply & fixing stainless steel plate rack, made out of 1.00mm thick sheet of size 24"x36"x10" deep, ISI marked, fixed as in repairs complete all as specified and directed.

M&L for Granite as in steps, pillars, window cills, cooking plateforms and like, 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) complete all as specified. ( size of the slabs shalll not be less than 100cmx60cm ) Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish all as spfd.

Supply & fixing pre-laminated particle board 19mm thick, interior grade pre laminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed as in repairs complete all as specified and directed.

Material & labour piano hings, mild steel bright finish width of flap 40mm fixed in repair including taking out the existing complete all as specified and directed

S&F Hasp and staple 75mm, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

S&F Grating square 150 mm size of PTMT (Minimum weight 100gms)

Supply & fixing of PVC waste down pipe of 40mm bore complete all as specified and as directed.

S & F in repair Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S& F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard / dense coil complete all as specified

Excavation in post holes (or similar holes) each n. exc 0.50 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc 25 cm, in Hard dense soil complete all as specified.

M&L PCC 1:2:4, type B-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc complete all as specified.

M&L for 75 mm Hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L PCC 1:4:8, type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc complete all as specified.

S&F Rolled sections Fe-410- W(Gde?E-250) quality-B as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

S&F Fe-410- W(Gde?E-250) quality-B Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment

Supply only chain link fencing MS galvanised fencing any size any types

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards, rails straining bolts et. Including provision of binding wire all as spd

S&F for Mild steel screw bolts(machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, ach screwed end to be fitted with washers and one hexagonal or square nut, exc 15cm and n exc 22.5cm long 5 to 10 mm of diamenter complete all as specified and as directed.

Taking down carefully copper/AImn point wiring (Light,Fan/Point Socket or power) (fittings such as switches ceiling roeses, pendent, regulators, sockets etc to be measured & paid seprately) & making good to disturbed surface of walls/floors etc.

M&L point wiring using approved colour coding as per IS with stranded copper conductor single core 1.5 Sqmm (Nominal area), PVC insulated cable in and incl PVC casing N caping (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories incl mild steel sunken boxes suitable for mounting switch/sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer incl mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, incl PVC insulated copper conductor 1.5 Sqmm (Nominal area) single core PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified. Note : Switch/sockets shall be measured and paid for separately :-

One light point controlled by one switch

One switch socket outlet 3 pin,5 Amp on the independent board

One switch socket outlet 3 pin,5 Amp on same board

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size

All as per item No 162.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 2.5 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 2.5 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.using 2.5 sqmm copper cable as continued earth wire .

All as per item No 162.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 4.0 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 4.0 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.

S&F Lamp holder,PVC insulated body, with back plate suitable for batten fitting, ISI marked complete all as specified

M& L switch piano, flush type, single pole 1 way 6 Amp,ISI marked complete all as specified

S&F switch piano flush type, single pole 1 way 16 Amp, ISI marked complete all as specified

M& L socket 5 pin 6 Amp piano flush type,ISI marked complete all as specified

S&F socket out let 2 in one 6 pin 6 & 16 Amp, ISI marked complete all as specified

S&F ceiling rose, 3 phase/ PVC/ polycorbonate,isolate bady, ISI marked complete all as specified

S & F LED bulb 9 watt.

Supply and fixing Decorative box type fitting Pre-wired for and incl LED tube 18/20 watt 6000K 4 ft IP20 linear LED T8 tubular lamp with extruded aluminium/PC body and PC diffuser complete with inbuilt driver complete all as specified and directed.

S&F Decorative wall light fixture made up of Polycarbonate , fancy type, made out of Polycorbaonate,suitable for B-22 base holder fixed as in repair complete all as specified and directed.

S&F sleek LED mirror light with diffuser 7/ 9 watt along with all accessories prewired including connecting with copper flexible cable of size 0.7 Sqmm 3 core and all as specified and directed .

S & F Bulkhead luminaire Decorative Energy saving new generation 10W LED IP65 with opal diffuser incl electronics driver & connection with copper flexible cable 3 core complete all as specified and directed.

S & F LED Building security light 25 /30 watt pressure die cast housing with individuals LEDs & Lens with modular secondary optics and IP65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light.

Supply and fixing wall Mounting LED fitting 9/10 watt 6000K 2 ft Basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver complete all as specified and directed.

Supply & Fixing Bracket made out of GI light grade pipe of 32 mm dia 1.5 mtr long bend to an angle of 120 degree with fixing arrangements on wall Complete all as in repair.

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 8 way, 240 Volt SPN

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 415 Volt TPN

S & F MCBs 'B' characteristics, Double pole , 240 V, 32 Amp breaking capacity 10 kA

S & F MCBs 'B' characteristics, TPN , 415 V,40 Amp breaking capacity 10 kA

S & F MCB B characterstic single pole 5 to 30 Amp, 240 volt breaking capacity 10 kA

M&L for submain wiring with 2 single core PVC insulated FRLS cable 6 Sqmm copper conductor PVC sheathed in and including rigid PVC concealed conduit heavy duty of suitable size incl cutting chiseling of wall and making good to disturbed surface of walls / floor etc with plastering painting etc so as to match with the existing finishes, drawn with 6 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with shaddle and connecting to common earth teriminals complete all as specified.

Single pole and Neutral Sheet metal enclosure with a 2 pin and earth plug and socket complete with one single pole MCB 20 Amps

Supply & Fixing exhaust fan, energy efficent metalic blades heavy duty turbo force of size 450 mm sweep, 900 rpm, AC, 230 volts complete with louvers, shutters, mounting on walls with holding down bolts, nuts, washers with cutting holes into or through stone/brick walls for fixing of 450 mm sweep exhaust fan including making good the cutting and matching the surface with existing surfaces and connection of flexible copper conductor cable three core ceiling rose to fan and testing complete all as specified.

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work.

Note:- (For Srl item No. 187.00) The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 7.5 metre from top of earth plate.

Excavation in trenches in hard/tense soil not exceeding 1.5 metre deep and not exceeding 1.5 metre wide and getting out including dressing / trimming sides and leveling/grading and ramming of bottom of excavation complete all as specified.

Returning, filling in including spreading, leveling, watering and well raming excavated soid in layers not exceeding 25 cm thick, filling back in trenches after cables have been laid and tested, poles, stays, struts have been erected and tested complete all as specified.

Removing of surplus soil to a distance n.exc 50 mtr and depositing at a level n.nexc 1.5 mtr above starting point where directed complete all as specified.

Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. Note:(i) Consolidated / Punned sand shall be considered for purpose of payment (ii) Sand shall be same as specified for plastering work and directed.

Supply and laying Sub Class 'B' common burnt bricks, old size, designated 75, laid dry, flat with width equal to length of brick & with gaps between the adjucent bricks not exceeding 10mm as cover laid over the cable to give mechanical protection to under ground cable, complete all as specified and as directed.

Supply and fixing in replacement GI pipe, light grade 50 mm bore, ISI Marked for protection to cable along the pole/across road crossing/passing through culvert complete all as specified and directed.

Supply, laying, jointing and testing in replacement of XLPE insulated, armoured, heavy duty LT cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area 16 Sqmm 4 core, complete, all as specified and directed.

S&F bell push, 6 Amps, SP, flush type, ISI marked complete all as specified

S&F Electric Bell , AC 230 volts, single pole, ISI marked complete all as specified

M& L switch piano, flush type, single pole 2 way 6 Amp,ISI marked complete all as specified

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 12 way, 240 Volt SPN

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector,8 way, 240 Volt SPN

Amount of credit of Rs. 124334.00 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

M/S Anil Gupta

Durga Construction

M/S VINOD KUMAR BANSAL

S.R.AND CO.

RAJESH BUILDERS

Arsh Builder