Civil Works

Amount

Clearing the Scrub Jungle clearance in the site premises and collecting the scattered debries from the campus and conveying away the same to outside by lorry to a lead of 3km (Entirely within city limit) including loading and unloading charges and dumping in low places and levelling neatly etc., complete complying with standard specification and as directed by the departmental officers.

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.

All soils

SDR Zone

Excavating Weathered Rock by wedging chiselling and trimming to proper shape by mechanical means where blasting is prohibited and directed by departmental officers etc complete.

Earth work Open excavation by Mechanical Means for Open Earthwork in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting in- clusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling Crushed Stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with Stone Dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with conveyed earth in layers of not more than 150mm thick layers well watered, rammed with surface vibrator and consolidated including conveyance charges etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers - Mixing by mechanical means

Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers - Mixing by mechanical means

Cement Concrete 1:3:6 (One Cement, Three crushed stone sand and Six broken stone jelly) using 40mm size hard broken stone jelly excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete and as directed by the departmental officers. - Mixing by mechanical means

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. as directed by the Engineer incharge and including cost of chemicals labour transportion etc.,

Damp proof course as per IS 3067:1988 with Cement Mortar 1:4 (One Cement and Four crushed stone sand) 12mm thick mixed with best approved quality Integral liquid water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification - Machine Mixing

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Circular columns

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c, etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and fixing Kwik stage propping for carrying design load carrying capacity and with stand any side movements of design load with necessary 50mm dia MS pipe cross bracings at spacing each row 1mx1m horizontally and vertically connecting each propping arrangements fully engaged each other with coupler bracings suitably placed at various levels (DOUGLAS) and hSevenths with plywood of 19mm thick board connecting with suitable scaffolding form work like Laced and Braced arrangements as per standard design and as directed by the departmental officers,etc.

Providing and laying in position, Standardised Concrete Mix M-30 Grade using In-situ Concrete batching plant/ Ready Mix Concrete (RMC) adopting weigh batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete,improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including Conveyance of concrete from batching plant to Work site, Electricity charges and other works & labour cost involved for concrete production, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

In Fifth Floor

In Sixth Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Plinth / Basement level

above plinth/Basement level

First floor

Second Floor

Third Floor

Fourth Floor

Fifth Floor

Sixth Floor

Traversing Type Corrosion Inhibiting concerated powder additive

Brick work in following Cement Mortar using best quality Fly ash Brick of size 230x110x75mm with class designation of 12.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. Cement mortar 1:3

For foundation & basement

For Ground floor

For First floor

Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. Cement mortar 1:5

Brick work in following Cement Mortar using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge. Cement mortar 1:6

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

In Fifth Floor

In Sixth Floor

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmentalofficers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

In First Floor

In Second Floor

In Third Floor

In Fourth Floor

In Fifth Floor

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used, hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. (The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work).

Treatment to side wall of varying thickness of basement floor, Lift pit, of main building from exterior surface covering the following sequence of operations :a) Providing, supplying, mixing, applying two coats of ready to use two component acrylic polymer modified cement based flexible water proofing slurry like TAPECRETE or approved equivalent conforming to IS to thickness of 2 mm on the surface of side wall prior to the chemical injection treatment is completed as specified under item above.b) Providing, supplying, mixing, laying cement screed plaster 20 mm thick in cement concrete slurry 1:2:4 mixed with 6mm & down grade course graded aggregate with water proofing compound like CICO NO:1 (normal setting integral water proofing compound) or approved equivalent conforming to IS at the rate specified by the manufacturer at any depth & height ove the coated surface of operation (a) above.Rate shall include for preparation of surface by mechanical upgrading to remove all loose mortar and laitance, oil, grease etc. and washing the surface with water to get neat surface, dewatering, finishing, curing, scaffolding, waterproofing chemicals, wastage, conveyance, tools and plants, mixing device and gauge, shuttering, Nozzles etc. complete as per manufacturer's specification and as directed.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed by the departmental officers.

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed by the departmental officers.

Brick Jelly Lime Concrete 1:2:5 using 20mm brick jelly in Lime Mortar 1:2 using limestone and sand 10 cu.m.

Ground floor

First floor

In Second Floor

In Third Floor

In Fourth Floor

In Fifth Floor

Supplying and fixing fine polished cuddapah slab of 20 / 30mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Double charged Vitrified Tiles 600 x 600 x 8mm

Flooring with ceramic tiles of following size and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 and above 20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete complying with standard speicification and as directed by the departmental officers. (The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) Dadooing with vitrified tiles of size 600mm x 600mm x 8mm.

Providing and Fixing of PVC Trims (Corner beading) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental officers.

Cladding the Vertical Wall Surface with Best Approved Ruby red and raw silk and other varities Granite Stone Slabs of Size 1200 x 600 of 18/20 mm thick with machine cut edges laid over a Cement Mortar bed of 10 mm thick using Cement Mortar 1:2 ( One Cement and Two Sand ) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width joints and pointing the joints with white cement mixed with matching colouring pigments etc., The Granite stone slabs and other materials to be used shall be got approved by the Executive engineer concerned before use on work etc., Complete as per standard specification.

Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing Double nosing to granite slab at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

FRAME:Fully Solid Core WPC-75MMx50MM:Providing and Fixing of Qute WPC/PVC Solid Door frame extruded with size 75mmx50mm.The inner core made of rigid WPC Compound with minimum shore hardness of 55,and Bulk Density 0.8 Grms/Cub.C.mt.The frame shall be fixed fixed to the wall using 10x100mm long M.S.Screw through the frame by using PVC Fasteners.A minimum of 4nos screws to be provided for each vertical member.

Supplying and fixing solid core flush shutter 35mm thick with commercial ply on both sides & teak lipping around and laminated on bothsides with 1 mm thick MICA sheet of approved design with necessary adhesive and C.P.screws, including fixing for aldrop, tower bolt, hinges and lock strike plates, putty, fevical etc., and including the cost of aluminium hinges 125x30mm size -3 Nos. Antique brass aldrop of size 250x16mm 1No, Antiquebrass tower bolt of size 250x12 mm -1 No. , Antique brass tower bolt of size 200x12mm-1 No, Antique brass door stopper with Nylon bush-1No. shall be provided. All aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 for anodic film thickness of not less than 15 microns. The rate is inclusive of cost of fevical,fixing charges, transportation, loading, unloading all other incidental charges and handling charges etc., complying with standard specifications

Single leaf

Double leaf

Supply and fixing in position of ornamental teak wood door frame with shutter of size 4.00m x 2.80m and teak wood scandling superior quality outer frame of size 100 mm x 75 mm and panel shutter of teak wood planks of 30 - 45 cm wide and 25 - 40 mm thick and required hight etc.Rate inclusive of cost of materials for frame, shutter planks, Labour charges frame work, Machine cut of shutter plank with required shape, and nessarry two coat of malamine finish etc.,complete and as directed by the departmental officers.

Hydraulic Door closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed adjustment like HARDWYN (make) 'GAZEL' (or) equivalent (with ISI Monogram)

Manufactruing, Supplying and fixing of 10 mm thick Toughened Fixed Glass View panel for flush door arrangement with the following specification. The outer frame of the glass partition should be made up of Teakwood scantlings of size 50mm x50mm with ornamental works. The 8mm thick thoughened glass should be sanwiched between two nos of T.W. Scantlings on both sides alround intact and the beedings should be polished with high quality polish material. The rate includes cost of T.W.Beedings, charges for toughening the 8mm glass, manufacturing, conveyence of all the materials to the work site, fixing in positition etc., complete as directed by the departmental officers.

Supplying and fixing of wood polymer composite (WPC) door with solid door frames extruded with size 75mmx50mm. The inner core made of rigid WPC compound with minimum shore hardness of 55 and buld density 750kg/cub.Mt. The frame shall be fixed to the wall using 10x10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screw to be provided for each vertical members, Door Shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of specified Design which is approved by engineering-in-charge. Both side of the shutter shall have rough sugar texture finish, laminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550kg/cub.Mt moulding the thickness remains 25mm (+/-1mm) etc. complete as per the direction of the departmental officers.(make Qute / Equivalent)

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations free pin headed glass 4mm thick should be provided in the louvers. The Ventilator should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supply and installation of Anutone (or) Equivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation,

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Supplying, Erecting, Manufacturing and fixing the Tensile roof structure using fabric tensile roof membrane. The structure shall be designed in accordance with IS:800 with the design wind speed as defined by IS:875 based on the location, site conditions...etc. The complete structure will be 200mm dia circular pipe having 6mm thickness and purlins 150mm dia with 5mm thickness with necessary bolts, nuts, wire rope, corner plate finished with two coats of epoxy primer followed by two coats of epoxy paint and approved colour...etc. The membrane fabric having 800 GSM and welding rigidity and fixing the necessary special Aluminium extrusions at the end of the roof tracks and special screws etc., Finally finishing the surface neatly as directed by the departmental officers etc., complete complying with standard specification.

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by mechanical means

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Crushed Stone Sand) to full depth of slab etc., complete complying with standard specification and as directed by the departmental officers.

Paving the Top of roof with Solar refelective ceramic tiles of size 305mm x 305mm x 7mm thick of approved quality and colour laid in Cement mortar bed in 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with water resistant tile epoxy grout for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position of cup-board shutters made of Teak wood scantlings of size 100mm x 32mm for outer frame, horizontal and vertical members. The shutter frame is made out of 75mm x 32mm of Teak wood scantling (horizontal - 3 Nos., vertical - 2Nos. for each shutter) with 12mm thick both side pre-laminated particle board (exteriar grade) shutters. The shutters are fixed to the frame with required 6 numbers of aluminium hinges 100x30mm, 2 Nos. D type aluminium handle 100mm, 2 Nos. of aluminium tower bolts 75x10mm, 1 No. of cupboard lock, etc. The teak wood frame shall be painted two coats with synthetic enamel paint over one coat of wood primer. The pre-laminated particle board and furniture fittings used should be got approved by the Engineer incharge before use. The cost includes cost of all materials labour charges etc.

Suppling and fixing position of polycorbonate sheet (Opaque White) roofing with following specification. The roofing made of 10 mm thick multi wall polycarbonate sheet roofing with following specification. The roofing made of 10mm thick multi wall polycarbonate sheet with approved colour (Lexan branded) double sided UV coated using MS frame work consists of main truss 50 x 50 mm MS square pipe for vertical support in the base plates and top connecting plate for fixing truss. The rate including cost of 10mm thick multi wall polycarbonate sheet, MS truss work, MS vertical support pillars, Horizontal purlins, Aluminium plate for bottom & top with sealent for all joint of sheets and labour charges for all fabrication works and sheet fixing work and necessary Scaffolding cost and painting work for all MS Truss with purlin etc., completed. and as directed by departmental officers.

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing Painting the wall with Texture Finish Paint including labour chargesetc. complete complying with standard specfication and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and laying of Interlocking Paver Block Stone 80mm thick Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers.

Paving with Rubber Moulded hydraulically pressed cement concrete paver block with pattern design of 50% colour and 50% Plain of 83 mm of approved quality and colour, over the sand filling to full depth of slab perfectly and neat finishing the joints, compressing with vibrator. The rate shall be inclusive of cost of paver block, taxes, incidental charges, transportion charges and labour charges for fixing, neat finishing the joints as directed by the departmental officers etc., complete complying with standard specification. The paver block should got approved by the departmental officers before use on work.

Providing granolithic floor finish of the 40mm thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Granular Sub-base with Graded Material (Table:- 400-1) - Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401) - for grading- V Material.

Wet Mix Macadam (Table 400-13) - Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density, Complete as per clause 406

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 12.5 litres capacity PVC flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

White glazed European Water Closet with 12.5 litre capacity PVC flushing tank fixed on to wall

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Providing & fixing Stainless Wash Sink of size 600 x 450 x 200mm depth with border width of 50mm including folding of edges of approved make, connection pipe of approved make & CP waste coupling over the Granite Platform including providing SS vertical splash board of 600mm ht.along with fixing G.I. waste pipe of 32mm dia ‘C’class Approved make below the sink upto Nahani trap through required fixing arrangement like Jam nut etc. complete as directed by the departmental officers .

Supplying and fixing position CI Nahani Trap of the size 100 x 75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75 mm dia

110 mm dia

160 mm dia

250 mm dia

300 mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re- doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

160mm dia PVC Elbow

110mm dia PVC Elbow

75mm dia PVC Elbow

110mm dia PVC Elbow with Door

75mm dia PVC Elbow with Door

110mm dia PVC Tee

75mm dia PVC Tee

110mm dia PVC Tee With Single Door

75mm dia PVC Tee With Single Door

110mm dia PVC Y

75mm dia PVC Y

110mm dia PVC Y With Single door

75mm dia PVC Y With Single door

110mm dia PVC bend

75mm dia PVC bend

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

75mm dia

110mm dia

Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - Internal water supply above/below ground level.

65 mm dia UPVC Pipe - Below ground level

50 mm dia UPVC Pipe - Below ground level

50 mm dia UPVC Pipe - Above Ground level

40 mm dia UPVC Pipe- Above Ground level

32 mm dia UPVC Pipe - Above Ground level

25mm dia UPVC Pipe - Above Ground level

20mm dia UPVC Pipe - Above Ground level

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements.

50mm dia UPVC Elbow

40mm dia UPVC Elbow

32mm dia UPVC Elbow

25mm dia UPVC Elbow

20mm dia UPVC Elbow

50mm dia UPVC Tee

40mm dia UPVC Tee

32mm dia UPVC Tee

25mm dia UPVC Tee

20mm dia UPVC Tee

50x40mm dia UPVC Reducer

40x32mm dia UPVC Reducer

32x25mm dia UPVC Reducer

25x20mm dia UPVC Reducer

50x40mm dia UPVC Reducer Elbow

40x32mm dia UPVC Reducer Elbow

32x25mm dia UPVC Reducer Elbow

25x20mm dia UPVC Reducer Elbow

50x40mm dia UPVC Reducer Tee

40x32mm dia UPVC Reducer Tee

32x25mm dia UPVC Reducer Tee

25x20mm dia UPVC Reducer Tee

50mm dia UPVC Hex Nipple

40mm dia UPVC Hex Nipple

32mm dia UPVC Hex Nipple

25mm dia UPVC Hex Nipple

20mm dia UPVC Hex Nipple

65mm dia UPVC union

50mm dia UPVC union

40mm dia UPVC union

32mm dia UPVC union

25mm dia UPVC union

20mm dia UPVC union

65mm dia UPVC Coupler

50mm dia UPVC Coupler

40mm dia UPVC Coupler

32mm dia UPVC Coupler

25mm dia UPVC Coupler

20mm dia UPVC Coupler

Supplying, laying and jointing CPVC pipes OF Standard Dimension Ratio 11 (Pressure class 1) conforming to IS:15778 - 2007 of approved quality and best variety of the following dia including cutting and fixing CPVC specials using CPVC adhesives (Solvent Cement) (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications and as directed by the departmental officers. (The CPVC pipes shall be got approved by Executive Engineer before use on works) - Internal water supply above ground level.

25 mm dia

20 mm dia

15 mm dia

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements.

25mm dia CPVC Elbow

20mm dia CPVC Elbow

15mm dia CPVC Elbow

25mm dia CPVC Tee

20mm dia CPVC Tee

15mm dia CPVC Tee

25mm dia CPVC Bend

20mm dia CPVC Bend

15mm dia CPVC Bend

25mm dia CPVC Coupling

20mm dia CPVC Coupling

15mm dia CPVC Coupling

25mm dia CPVC union

20mm dia CPVC union

15mm dia CPVC union

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

20 mm dia G.M. Gate Valve

25 mm dia G.M. Gate Valve

32 mm dia G.M. Gate Valve

40 mm dia G.M. Gate Valve

50 mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

15mm dia Long Body Tap

15mm dia Stop Cock Tap

15mm dia Swan NeckTap

SD Tap

Pillar Tap

Supplying and fixing in position Healtyh faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works).

Supplying and fixing in position 150 x 100mm “P” or “S” stoneware gully trap ‘A’ grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as di- rected by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete - Depth per cm

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers.

160 mm dia - five floors

Providing rain water recharging collection pit having a size of 900mm dia to a total height of 1200mm is 150mm above ground level and 1050mm below ground level with necessary augar bore of 300mm dia to a depth of 3000mm from bottom level of collection pit and filled with 20mm HBG stone jelly inside of augar bore. The sides of collection pit provided with RCC Well ring of inner size of 900mm x 300mm x 50mm with 6mm reinforcement on both direction at 200 mm c/c using RCC 1:1/2:3 (one cement, one and half sand and three HBG jelly). The top of collection pit is finished with 50mm thick cover slab, The collection pit is filled with course river sand at top, 20mm HBG stone jelly at middle and 40mm HBG stone jelly at bottom of a depth of 300mm, 450mm and 450mm respectively. The rate is including the cost of RCC well ring and filling materials, RCC cover slab, drilling hole and labour charges for erecting the well ring etc., and as directed by the departmental officers.

Supplying and fixing in position first quality and approved PVC Water tank complete complying with standard specifications. The PVC Water tank to be used on work should be got approved by the Executive Engineer before use on work.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of Clay burnt Bricks of size 9” x 43/8” x 23/4” with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

size 600x600 mm

size 900x900 mm

Supply and fixing Shera Board of natural fibres bonded of Cement Board 6mm thick water resistant with necessary painting and Support materials fixed at all levels, complete complying with standard specification and as directed by the departmental officers,The materials should be got approved by the Executive Engineer before use on works.

Supplying and fixing of 5.00 HP of approved brand Submesible Pumpwith accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying & Installing CURTAIN BLINDS with Sunscreen perforated Roller blind optima series Basket 125 Tex with fabric specification of (Fabric compositition polyster 22% and PVC78%, Openenss Factor-5%, Thickness -0.68MM +/-5%, weight per m2 -480 GSM, yarns count in wrap/ weft/cm 19/18+/-5%, Fire Resistance-FR(USA) KFI(Korea), Tear Resistance-wrap11.9 daN+/ 5%,WEFT 150 daN+/-5%,colour fastness-6-7/8 (white colour base), artificial llight xenon lamp, UV resistance Min3 (White colour base), width 2.5M & 3 M. The Roller mechanism shall be a moulded unit made from engineering grade plastic polymer with PVC spring support. The Fabric shall be attached to the roller tube with high quality self adhesive tape with manual operation. The fabric shall be attached to the tube with adhesive strip. It should have minimum one ton fabric which must be placed on the roller before the working section of fabric start Operational action shall be smooth including necessary hardware for fixing at all places & as directed by Engineer-in-charge etc complete. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc. complete and as directed by the departmental officer (The materials quality, brand, colour, shade should Be approved by the Executive Engineer before use on works).

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact 250 Litres capacity

Providing and placing in position Single Bed of Overall Size:-L-2050mm X W-900mm X 550mm H. Material:-Wooden Understructure : 'C' type frame & Cross members are made up of in 25X25X1.2mm THK MS Square pipe conforms to IS 4923 and the frame finished with powder coat up to 50 -60 MICRON . Horizontal plinths and bottom plinth are made of 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Head Board/Tail Board/ Side rail board are made of 18mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992) with imported HDF/ Membrane foil wrapped decorative trims fixed to it. Mattress panels of Bed are made of 18 mm thick 25mm. thick Particle Board (E-1 Grade), melamine finishes with matched 2 mmProv PVC edge-banding.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Construction:-Knock Down Construction. The product should be complete as per sample approved & as per direction of Engineer-in-charge.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality

Providing and placing in position Single Bed Mattress of size 2.05Lx0.90W it's a genius that dynamically adapts to the shape, and size of your different body parts – all thanks to its cutting-edge grid technology. The SuperGrid mattress is made with intelligent air columns that reconfigure to adjust to your body's unique shape, sinking in the heavy bits like your torso and gently cradling the lighter parts like your head and legs. At every toss and turn, the grid readjusts to perfectly support your posture. It's not a one-size-fits-all – it's your-size-fits-perfectly kind of a deal. Here's the cherry on top – each of the air chambers is infused with copper so the mattress always remains cool while our grid is 100% recyclable and committed to an eco-friendly, circular journey.

Providing and placing in position Pillow & Bedsheet This standard has been revised on the basis of experience gained in implementation of its previous version by handloom industry.In this revision, requirements of dimensional changes, scouring loss, pH value have been modified.The composition of the Committee responsible for formulation of this standard is given in Annex E.For the purpose of deciding whether a particular requirement of this standard is complied with the final value,observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance withIS 2: 1960, LRules for rounding off numerical values (revised)’. The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.To provide product specifications to pillow manufacturers and consumers that will maintain the highest product performance standards.Before any product can be certified and bear the IngeoTM brand, manufacturers must sign licensing agreements to meet manufacturing guidelines and product standards.

Manufacturing, providing and placing in position machine made factory assembled Table Size 3 feetx 1 feet 9 inchType-1 of make . Providing & Placing Office Table with following details and specifications : Top and legs are made of 25mm thick Particle Board (E-1 Grade), melamine finish with matching 2mm PVC edge-banding. The Modesty is Particle board wood Grade E-1 (Environmental Friendly) thickness 18 mm cover with Melamine Edge-Banding 2 mm PVC Lipping. Workrtop provided with standard rectangular Grommet with cover on either end of the table. Prelaminated Drawer Unit of size 400mm W x 600mm D x 150mm H to be provided with Melamine finish and 2mm thk PVC edge banding. E1 Grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1892). Product should be BIFMA gold rated SCSglobal certified for inhouse air quality.Main Table :- 1200mm X 600mm X 740mmH

Supplying of 3 Seater: W 2050 D 750 H 700 SH 430 Seat & Back : Seat & Back of the Sofa shall be Solid high density machine injected foam with MS/wooden structure inside the foam and covered with fabric of approved finish and approved colour. Base : Base of the sofa made out of Steel structure with Ms powder coated finish legs.

A standard 6-seater dining table is typically rectangular, measuring about 1500–1800 mm in length, 850–1000 mm in width, and 740–760 mm in height, with each seat requiring roughly 600 mm width for comfort. The chairs generally have a seat height of 450 mm, backrest height of 850–900 mm, and a leg clearance under the table of around 610–630 mm. For ease of movement, a minimum 900 mm clearance should be maintained around the table. Common materials include solid wood, engineered wood, tempered glass, or marble, with finishes such as PU polish, melamine, laminate, or veneer, and chairs often feature cushioned or upholstered seats for added comfort.

Supplying and erecting Gas Line Work MS 1/2" C Class Tada Pipe and all Fittings 1. L Fittings 2. T Fittings 3. Unions 4. On/Off Valves 5.Meter, Painting Work, Laying and Fixing Work.

The 65mm Thick 32dB sound rating movable walls are typically used as a privacy separation in Residential projects and in dining area where partition without acoustics but with privacy is desired.A common application area for 65 series non acoustic panels is division between hall & bedroom, hall & kitchen, foyer & dining area. The most affordable type of movable partition comes without floor guides and the locking of the panels can be done manually using jack type scissor winding mechanism. The system is trouble free and can run for years. A range of customized layout option is possible in the partition such as inset pass doors, Full Height Doors, Inset Glass Panel, etc.The trims and panel finishes can also be totally customized as per the client’s choice. The stacking of panels can also be custom made as per the client choice.

Supplying and fixing of GI Metal Single Leaf Door (Duct door) with Insulated PU Adhessive Honeycomb structure infill for stability, door skin In 1 mm Thickness, frame Sheet Thickness 1.2 mm with powder coated of size 1000 X 2100 - Single Leaf Shaft Door - 4 Side Frame including Ball Bearing Butt Hinges (Geze) 4"x3"x3-3Nos, Shaft lock with Allen key (GEZE)- 1 No, Flush Pull Size: 102X45MM (GEZE)-1 No, Vision Panel-1 No, FIRE RATED Glass Size: 200X300X5mm-1 No, Anchor Bolt-7 Nos of specified Design which is approved by engineering-in-charge etc. complete as per the direction of the departmental officers

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm nominal dia

100mm nominal dia

80mm nominal dia

25mm nominal dia

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers. - 200 mm dia

Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers. - 150 mm dia

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of size 100 NB to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT. - 3 core 10 sq.mm. armoured copper cable

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT. - 2 core 2.5 sq.mm. armoured copper cable

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification. - 100 mm

Servicing the SS Hydrant Valves by disconnecting from pipe line, dismantling, checking the operation of rotating spindle, replacing rubber 'O' ring of valve seating, repalcing rubber gasket of 80mm dia OD x 65mm dia ID, repalcing the 5/8" x 21/2 bolt, nut, washers, re-connecting with hydrant system as per standard methods and as directed by the Departmental Officers.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply and fixing in position of Fire Fighting Duct Window having proper glass window type double door with universe open key, painted inside white and outsid post office red for the sizes of 1300 x 900 x 500mm (L x B x D) fabricated using 25 x 3mm MS 'L' Angle and all sides covered with 2mm thick MS sheets, suitable arrangements to kept 2 Nos. of Fire Fighting Hoses and 1 No. Branch Pipe, mounted in fire duct using anchor fasteners, etc., as per standard specifications and as per directed by the Departmental Officers.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply & Installation of Gun Metal Ball Valve of size 25mm dia size including necessary Fittings

Supply & Installation of in position the sign board of "EXIT " with arraow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Providing and fixing 2 hr fire rated doubble skin ste door constructed from 1.25mm thick galvanized ste sheet formed to provide a 46mm thick fully flush door shl with lock seam joints at stile edges and the internal construction of the door is a specially designed Honey Comb structure with reinforcements at top, bottom and stile surrounds. As per IS 3614 part-1 & part-2 for stability and integrity and Pressed Galvanized ste confirming to IS 277. Fire door should be tested at CBRI or ARAI for maximum rating of 2hrs with vision pan. Vision Glass pan should be 6mm thick clear glass provided in square in standard dimensions of 300mm x 300mm. Door Frame should be produced from 1.6 MM thick galvanized ste sheet formed to double rebate profile of size 143mm X 57mm (+/- 0.3mm) with a maximum bending radius of 1.4mm and fixed as per manufacturers specification. Including all approved type( Dorma Make) heavy duty fastenings and fixtures comprising of :S.S. Ball Bearing Butt hinges 3 mm thk, Mortise Sash Lock with Panic bar, D handles, Mortise Dead Bolt, Mortise Latch, Door Closer, air seal gaskets between shutter and frame, etc complete.The door frames and door shutters are primed with Zinc-Phosphate Stoving Primer and finished with Polyurethane Aliphatic grade or epoxy paint as per approved manufacturer specifications. (Supplier -Shakti Met-dor or approved equivalent). (Note - Test certificates should be available for vision pans as part of the fire door assembly. Independent glass test certificates will not be accepted. Manufacturer test certificate shall cover doors both single and double leaf and all doors supplied should be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper lab confirming the type of door and the hourly rating is mandatory.)

Supplying and fixing of cylindrical vertical notational polythene water storage tank confirming to IS. 12701 / 96. The tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simple pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank, and the tank should be fixed firmly. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., complete complying with standard specification and as directed by the departmental officers. (The water tank should be got approved by the Executive Engineer before use on works by the Departmental Officers.

Supplying and placing of Wooden Dining Table size of 4'x 3' and Wodden Dining Chairs 4 Nos. The legs are teak wood of first quality and the top and sides shall be constructed out of 16mm thick teak wood board flush jointed the polish shall be non- water based stain polish with melamine finish for longer life and smooth fisih. All the undersides or non-visible timber surfaces finished with wax polish.

Supplying and placing of Wooden Tea poy of size 3' x 1.5'. The polish shall be non-water based stain polish with melamine finish for longer life and smooth finish. All the underside or non-visble timber surfaces finished with wax polish.

Supplying and placing of 3 Seater Sofa Providing sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,

Supplying and placing of Single Seater Sofa Providing sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,

SS 304 SINGLE BURNER RANGE- 600X600X450 MM Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Inner Frame : SS Angle & SS Pipe, With 25x25 sqr tube .Ring Square Ring, Burner : G - 10 Burner, Cover : Four Sides Half Cover by S.S.Sheet With L P gas Accessories Inbuilt Of Range, Legs : 1 ½ ” Square SS Pipe 16gBush : Adjustable

SS 304 DOUBLE BURNER RANGE- 1800X600X450 MM TWO BURNER MADE WITH 304 16G TOP LEG WITH 32 DIA PIPE WITH 25 MM DIA CROSS SUPPORT ,WITH 2 NO VESSEL REST CASTING WITH 1NOS T BURNER AND 1 NO M BURNER WITH DIP TRAY .THE UNIT MAKING PROCESS BY CNC CUTTING BENDING TIG WELDING FINISH WITH 5 STAGE AND MATT FINISH . INNER FRAME-32X32 L ANGE

Dosa Cooking Range Fully 304 Grade (Glass Wool Packing )Top : 1 ½ ” Square SS Pipe Frame,Splash : Three Side 6 ” Height SS Splash withWater Outlet ( Removal Type ),INNER FRAME-32X32 L ANGLECovered : Outer Two Side Half Covered by S.S.Sheet - Matt Finished,Covered : Inner Two Side Half Covered by GISheet, Heat Proof : Glass Wool Packing,Burner : 2 Nos ""V"" Type Dasa Burner, DosaPlate : 20 mm Thickness MS Plate, Legs : 1½ ” Square SS Pipe, Support Legs : 1 ¼ ” Round SS Pipe 16g ,Bush : Adjustable Nylon Bush. Size: 1800X900X850+150 MM L x B x H +Splash )"

SS 304 IDLY BOX-360 NOS SS IDLI BOX 240IDLY CAPACITY (double jacketed Idly box mango model inner and outer made out of 18g)

SS 304 BATTER TABLE-1150X450X850 MM "Batter Table Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Vessel :10 Liter Vesse With Lid 4 no's. Bottom : OPEN. Legs : 1½” Square SS Pipe, Bush : Adjustable Nylon Bush. INNER FRAME-25X25SQR TUBE

SS 304 MASALA TROLLEY-900X600X850 MM Top : 1.5 mm Thickness Salem Stainless steel Sheet - Matt Finished, GN PAN: 9 NOS Bottom : OPEN. Legs : 1½” Square SS Pipe 16g , Bush : Adjustable Nylon Bush. INNER FRAME-25X25 SQR TUBE

Work Table ( T/ B ) Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished Inner frame:25X25 SQR TUBE 16 G THICK Bottom : TWO Under Shelf by 18g SS Sheet Legs : 1½” Square 16g SS Pipe, Bush : Adjustable Nylon Bush. Size : 1400X600X850 MM(L x B x H )'

Work Table Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Inner frame:25X25 SQR TUBE 16 G THICK Bottom : TWO Under Shelf by 18g SS Sheet Legs : 1½” Square 16g SS Pipe, Bush : Adjustable Nylon Bush. Size : 1200X600X850 MM(L x B x H )' Inner frame:25X25 SQR

SS"STEAM BOILER GAS OPERATED 500L BOILER 0.9KG PRESSURE (outer and inner 8mm SS sheet, 2"" and 3"" TATA 'C' pipe and 5"" top pipe , 10mm flange set top and bottom, MS bolt and nut 3MM gas cut, SS colour and SS angle stand 0.6 SS glading sheet and glass woll inculcation GG set, Lball valve , float valve, SS ball valve dide wait SS safety valve, pressure gage set) T50 BURNER 1 NO"

SS SINGLE JACKETED RICE VESSEL-150 LTR THE UNIT MADE UP OF 2MM 304 GRADE 150 LITR CAPACITY The vessel inner and outer made out of 14G thick leg made out of 50x50 with 16 g thick square tube with steam dropper and lid made out of 18g thick sheet.Lip made out of 5/8 th rod.

SS DOUBLE JACKETED SAMBHAR VESSEL 2MM 304 GRADE - 150 LITER CAPACITY The vessel inner and outer made out of 14G thick with side support 75mm dia rod and leg made out of 50x50 with 16 g thick square tube with steam dropper and inner support angle and bottom (inner-2mm and outer -3 mm thick with steam inlet and drain valve) lid made out of 18g thick sheet.

SS MILK VESSEL 2MM 304 GRADE - 100 LITER CAPACITY The vessel inner and outer made out of 14G thick with side support 75mm dia rod and leg made out of 50x50 with 16 g thick square tube with steam dropper and inner support angle and bottom (inner-2mm and outer -3mm thick with steam inlet and drain valve) lid made out of 18g thick sheet.

"Atta kneader-20KG Used to knead atta flour for Poori, Chapathi & Parathas. Made of sturdy components which ensures a trouble free service, A right ful choice of bakers and star hotels Kneading bowl & arm made of stainless steel. It providing large amount of dough within a few minutes. High grade stainless steel and other materials High torque motor and braking systems. Suitable for commercial use. Quantity : Motor 1.5H.P(220-240)50Hz

" Semi Automatic Roti Making Machine Super Deluxe Technical Specification - Machine Grade : Automatic Roti Machine - Roti Production Capacity : 2000 Roti/ Hr. - Size of Roti : As per Your Requirenments (Adjustable Min. 2” to Max. 7” Inch) - Weight of Roti : As per Your Requirenments (Adjustable Min. 10 to Max. 70 gm) - Thickness of Roti : As per Your Requirenments (Adjustable Min. 1.2 to Max. 6 mm) - Eectrical Supply : 440 Volt (Three Phase) - Electrical Connection Load : 32 Amp. (4 Pole MCB )Item & Description Qty Rate CGST SGST Amount - Electrical Consumption : 5 Unit/ Hr. - Roti Baking Design : Z Type Three Layer Conveyor Technology - Gas Supply Connection : As per Your Availability (LPG OR PNG (Naturel Gas Pipe Line)) - Gas Inlate Pressure Require : 0.5 kg/ cm sq. - Gas Consumption : 5 to 5.5 kg/ Hr. - Gas Inlet Safety System : Gas Pressure Regulator - Roti Appearance Colour : Light Brown - Machine Size : 6.10' (L) X 3.9' (W) X 4.9' (H) ft. - Machine Weight : 900 kg. - All Contact parts : SS 304 - All Cover and Gaurd : SS 304 (Thk. 1.2 mm) - Roti Baking Conveyor Patti : SS 304 (Thk. 3 mm) - Base Frame : MS - Chain Sprocket and Shaft : MS with Galvenize Coating - Motor : Crompton - Gear box : Elecon - Bearing : SKF and FAG (With Filled High Temperature Grease) - Electrical Parts : Siemens and L&T - Electrical Wire : RR and Polycab Cable - Emergency Safety Switch : Yes Push Type Switch - Pressing Plate : Anodized with Teflon Coating - Machine Cleaning : Easy Pressing Plate Openable (Hinge Type) - Machine Movable : Yes (6"" Castor Wheel with Brake) - Extra Feature Require : Yes Fullfilments As per Your Requirenments Extra Cost Payble)"

"DOUGH BALL MAKING MACHIN-- Production Capacity : 1400 Nos./ Hr.(Depend on Dough Weight) Weight of Dough : As per Your requirenments (Adjustable Min. 20 gm to Max. 60 gm ) Electrical Supply : 230 Volt Electrical Consumption : 0.4 Unit/ Hr. Overall Dimension : 2.8(L) x 1.7(W) x3.5(H) ft. Weight : 70 kg. All Contact Parts : SS 304 & Food graded All Cover : Stainless Steel 304 Base Frame : MS Dough Weight Accuracy : 3 gm Motor : Crompton Gear Box : Elecon Bearing : SKF and FAG Electracal Parts : Siemens and L&T Wire : RR and Polycab Emergency Switch : Yes Machine Cleaning : Easy Extruder Openable Machine Movable : Yes (2"" Castor Wheel with Brake) Extra Feature require : Yes

Work Table ( T/ B ) Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Inner frame:25X25 SQR TUBE 16 G THICK Bottom : TWO Under Shelf by 18g SS Sheet Legs : 1½” Square 16g SS Pipe, Bush : Adjustable Nylon Bush. Size : 1500X750X850 MM(L x B x H )' INNER FRAME-25x25 sqr tube

Work Table with sink- Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Inner frame:25X25 SQR TUBE 16 G THICK Bottom : Cross support Legs : 1½” Square 16g SS Pipe, Bush : Adjustable Nylon Bush. Size : 1400X600X850+150MM(L x B x H )' inner frame 25x25 sqr tube

Tilting Bratt Pan 150 LIT- LPG Operate A) S.S. 304 GRADE MATERIAL WILL BE USED FOR WHOLE BODY B) S.S. 304 14 SWG FOR FRYING PAN. C) S.S. 304 18 SWG FOR TOP LID OF THE FRYING PAN. D) S.S. 304 20 SWG FOR BOTH SIDE CONTROL BOX REMOVEABLE PANEL. E) S.S. 304 20 SWG FOR NON REMOVEABLE PANEL. F) MS POLISHED 10 MM THICK BOTTOM PLATE FOR FRYING PAN. G) MECHANISM FOR LID WILL BE SPRING LOADED. H) S.S. 304 SQ. TUBE 50MM X 50MM X 2MM THICK FOR UNDER CONSTRUCTION FRAME WORK WILL BE DONE . I) Gas Burner & Fittings Specs :- LPG FITTINGb RV BURNER , PILOT BURNER, NEEDLE CONTROL VALVE, COPPER PIGTAIL ETC. J) M.S TATA 'C' CLASS PIPE FOR GAS MANIFOLD K) WATER FAUCET WILL BE MOUNTED ONTHE RHS CONTROL BOX WITH 1/2" BSP 1 MTR WATER INLET FELXIBLE PIPE. L) HEAVY DUTY GEAR & WORM MECHANISM WILL BE USED FOR JERK FREE PRECISE CONTROL DURING TILTING . M) ON THE FRONT SIDE OF RHS CONTROL BOX HAND WHEEL WILL BE PROVIDED TO TILT THE TANK. N) HEAVY DUTY GEAR, WORM, TANK SHAFT AND MOVEABLE PEDESTAR BEARING MECHANISM WILL BE DONE INSIDE THE RHS CONTROL BOX. O) UNIT FOUNDATIO

"SS Tilting Grinder - 15 Liter Capacity - Crompton motor 2HP 3 phase We are instrumental in offering a quality range of Tilting Grinders that is used in different hotels and restaurants. The offered grinder is tasted on different quality parameters and is widely demanded in the market. Drum & box is made up of stainless steel material Coconut scrapper is attached Easy to operate It ensures hygiene. Cleaning process is easy easy Quantity : Motor 2 H.P(220-240)50Hz"

"SS Tilting Grinder - 5 Liter Capacity - Crompton motor 1/2HP We are instrumental in offering a quality range of Tilting Grinders that is used in different hotels and restaurants. The offered grinder is tasted on different quality parameters and is widely demanded in the market. Drum & box is made up of stainless steel material Coconut scrapper is attached Easy to operate It ensures hygiene. Cleaning process is easy easy Quantity : Motor 1/2 H.P

"Potato Peeler Machine - 15Kg Capacity Fully ss construction Strongemerybondingfor peeling Water inlet tube provides. Drain outlet provided for waste disposal Made of high quality stainless drum and frame Quantity : Motor 1H.P(220-240)50Hz"

Wet Pulverizer Machine 2 Hp Motor 25 to 30 kg

"Pot Rack Fully SS 304 Grade Frame : Outer 1” Square SS Pipe & Inner ¾ ” Round SS Pipe 16G Shelf : 3 No's Shelf's, Legs : 1½ ” Square SS Pipe 16G, Bush : Adjustable Nylon Bush. Size : 1500X600X1800 MM

SS 304 PALLET-1500X600X200 MM "Pallet Fully SS 304 Grade Outer Pipe : 1½ ”Square SS Pipe 16g, Inner Pipe : 1½ ” quare SS Pipe 16g, Bush : Adjustable Nylon

"Potato & Onion Bin Fully SS 304 Grade Top: 1.2 mm Sheet with 2 no's Lid. Bottom: One under Shelf by SS Sheet, (Center Partition Provided) Covered: Four Sides 1"" x 1"" SS Weld mess Fixed & Front Side Small Size Door 2 no. Frame: 1½” Square SS Pipe, Bush: Adjustable Nylon Bush. Size: 1200 x 600 x 850 mm

SS STORAGE RACK-1800X450X1800 MM "Storage Rack Fully SS 304 Grade Top : 1.2 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Shelf : 5 No's Shelf's, Legs : 1½ ” Square SS Pipe 16g, Bush : Adjustable Nylon Bush.

SS 304 STORAGE RACK-1400X450X1800 MM "Storage Rack Fully SS 304 Grade Top : 1.2 mm Thickness Salem Stainless Steel Sheet - Matt Finished,Shelf : 5 No's Shelf's, Legs : 1½ ” Square SS Pipe 16g, Bush : Adjustable Nylon Bush

Work Table Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Inner frame:25X25 SQR TUBE 16 G THICK Bottom : TWO Under Shelf by 18g SS Sheet Legs : 1½” Square 16g SS Pipe, Bush : Adjustable Nylon Bush. Size : 1400X600X850 MM INNER FRAME: 25x25 sqr tube

"vegetable cutting machine sage/Application : Commercial Power Source : Electric Capacity : 150. 200 Kg Par he Automation Grade : Semi Automatic Frequency Condition : 50 HZ, 230 VOLTS New Brand : AV- HERRY RED Coating : POWDER COATING"

HEAVY DUTY MIXER-10 LITR 2 HP

SS 304 VEG WASH SINK- 200X600X850+150 MM THE UNIT MADE UP OF 304 MATERIAL 16 G THICK TEH LEG MADE UP OF 40X40 SQR TUBE 16 G THICK

SS STORAGE RACK-1800X450X1800 MM "Storage Rack Fully SS 304 Grade Top : 1.2 mm Thickness Salem Stainless Steel Sheet - Matt Finished, Shelf : 5 No's Shelf's, Legs : 1½ ” Square SS Pipe 16g, Bush : Adjustable Nylon Bush.

SS 304 PALLET-1500X600X200 MM "Pallet Fully SS 304 Grade Outer Pipe : 1½ ”Square SS Pipe 16g, Inner Pipe : 1½ ” Square SS Pipe 16g,Bush : Adjustable Nylon

WEIGHING SCALE 150KG

SS 304 FOOD TROLLEY-1200X 600X 900 MM

"3 Unit Sink Fully SS 304 Grade Top : 1.5 mm Thickness Salem Stainless Steel Sheet Matt Finished Splash : Front Top Level 6 ” Splash Legs : 1 ½ ” x 1½” SS quare Pipe 16g Outlet : Waste Coupling Provision Bush : Adjustable Nylon Bush Size : 400X750X850+150 MM

Dish Landing Table with Chute Fully SS 304 GradeTop : 1.5 mm Thickness Salem Stainless Steel Sheet Matt Finished, Bottom : Open. And chut Legs : 1½” Square SS Pipe, Bush : Adjustable Nylon Bush. Size : 1500 x 750 x 850 + 150 ( L x B x H + Splash )" INNER NAME-25X25 SQR TUBE

SS 304 ENTRY TABLE WITH SINK -1100 X750X880+150 MM the unit made with SS 304 top 16g (1.5 mm) thick. SINK BOWL SIZE 450X450X300.the leg made with 40X40 SQ TUBE cross support 25X25 SQ tube CNC cutting and CNC bending with TIG welding and 5 stage finish

SS 304 EXIT TABLE WITH SINK -1100 X750X880+150 MM the unit made with SS 304 top 16g (1.5 mm) thick. SINK BOWL SIZE 450X450X300.the leg made with 40X40 SQ TUBE cross support 25X25 SQ tube CNC cutting and CNC bending with TIG welding and 5 stage finish INNER FRAME-25X25XSQR TUBE

PLATE RACK

Glass Rack

CUTTORY RACK

Pre - Rinse Unit

INSURANCE

GAS PIPE LINE 1/2 ms pipe 150 feet 4+4 manifold connection 10 gas connection Ms pipe fitting Pipe clamps Pressure gauge Presser control regulators Gas houses Click on adoptors Gas nrv valves NCV Valves materials and installation testing and painting

3/4 ms pipe steam line 60 feet ,ms union ms pipe fitting , ball valves, tee joints, steam nrv valves, installation work, boiller vessels and boiler installation work

"Exhaust System with Filter *SS Suction Hood *Size : 2400X1200X500 MM STEAM COOKING AREA-The Hood Made Out of 22G SS Sheet,The Filter ssembly Made Out of 22G SS Sheet, Provision For Oil Drain

Hood Erection &Fitting Charges Including*Ducting Made by GI Sheet, Angle Frame Support Stay Rates Bold Nuts *Approximate : 245 SQF"

LLS Centrifugal Blower with dynamic Balanced Impeller 3HP Motor 3 phase

BLOWER STAND

"Exhaust System with Filter *SS Suction Hood *Size : 2100X1200X500MM STEAM COOKING AREA-The Hood Made Out of 22G SS Sheet,The Filter Assembly Made Out of 22G SS Sheet, Provision For Oil Drain

Hood Erection &Fitting Charges Including*Ducting Made by GI Sheet, Angle Frame Support Stay Rates Bold Nuts *Approximate : 700SQF"

LLS Centrifugal Blower with dynamic Balanced Impeller 7.5HP Motor 3 phase

CHOPPING BOARD 24" X 24 "1.5 Thickness 2 (W,R,Y,G)

PEST CONTROL INDIA,MODEL - SPRIDER SPRIDER STANSARD UVA TUBE LIGHT MODEL - 445X342X140

ALUMINIUM HANDI-300 LTR

ALUMINIUM HANDI-250 LTR

ALUMINIUM HANDI-150 LTR

ALUMINIUM HANDI-100 LTR

Pressure Cooker 22L

MS POWDER COATED CUPBOARD WITH GLASS 36"X18"X78"

MS POWDER COATED CUPBOARD WITH OUTGLASS 36"X18"X78

LPG Leakage detector-GV 09+ SENSOR MODULE Gas Detector Toxic/Combusible Gas) Catalytic Type Sensing 7 Segment LCD Display Inbuilt Self Diagnoses LED indicator for Power/Alarm RS 485 communication Inbuilt SPDT Relay

KNIFE

SS SERVING VESSELS-30LTR

ONION PEELER MACHINE-1 HP SINGLE PHASE

SS 304 DOUBLE DOOR FREEZER-500LTR

SS 304 DOUBLE DOOR Refrigerator-500LTR

Design, Fabrication, Supply and installation of a 1mm MS (Mild Steel) sheet metal enclosure with a vict cutter opening for a 440V LT distribution panel, along with the necessary support structure using square tubes with Perforated MS sheet, fabrication of the suppor! structure, and ensuring the view cutter is properly integrated. cutting is used to precisely cut the sheet according to the panel's design Ensure the Perforated is precise and clean to avoid burrs or sharp edges that could pose safety hazards. The entire enclosure is supported with main structure Square Tube Fabrication: of size 1.0" × 1.0" and 1.5" x 1.5" MS square tubes welded or joined to form the frame and support the MS sheet enclosure depending on the specific design. The entire enclosure is neatly painted with two coats of Red Oxide and two coats of enamel paint for a neat finish, with necessary Latch for locking.

Providing and fixing 2 hr fire rated doubble skin ste door constructed from 1.25mm thick galvanized ste sheet formed to provide a 46mm thick fully flush door shl with lock seam joints at stile edges and the internal construction of the door is a specially designed Honey Comb structure with reinforcements at top, bottom and stile surrounds. As per IS 3614 part-1 & part-2 for stability and integrity and Pressed Galvanized ste confirming to IS 277. Fire door should be tested at CBRI or ARAI for maximum rating of 2hrs with vision pan. Vision Glass pan should be 6mm thick clear glass provided in square in standard dimensions of 300mm x 300mm. Door Frame should be produced from 1.6 MM thick galvanized ste sheet formed to double rebate profile of size 143mm X 57mm (+/- 0.3mm) with a maximum bending radius of 1.4mm and fixed as per manufacturers specification. Including all approved type( Dorma Make) heavy duty fastenings and fixtures comprising of :S.S. Ball Bearing Butt hinges 3 mm thk, Mortise Sash Lock with Panic bar, D handles, Mortise Dead Bolt, Mortise Latch, Door Closer, air seal gaskets between shutter and frame, etc complete.The door frames and door shutters are primed with Zinc-Phosphate Stoving Primer and finished with Polyurethane Aliphatic grade or epoxy paint as per approved manufacturer specifications. (Supplier -Shakti Met-dor or approved equivalent). (Note - Test certificates should be available for vision pans as part of the fire door assembly. Independent glass test certificates will not be accepted. Manufacturer test certificate shall cover doors both single and double leaf and all doors supplied should be within the tested specimen, deviation in specification and sheet thickness other than what is mentioned in the test certificates are not allowed. Proper lab confirming the type of door and the hourly rating is mandatory.)

Supplying and fixing of cylindrical vertical notational polythene water storage tank of various litres confirming to IS. 12701 / 96. The tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simple pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank, and the tank should be fixed firmly. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., complete complying with standard specification and as directed by the departmental officers. (The water tank should be got approved by the Executive Engineer before use on works by the Departmental Officers.

Suppying and fixing Cold Room - Chiller of Dimensions (Mtr) Ext 2.5 (D) x 3.04 (W) x 2.44 (H) Ambient Temperature + 40 Deg C Room Temperature + 2 to + 8 Deg C Refrigeration systems and model RUAH 1014KP – 1 No- ODU + IDU R404a Gas Total refrigeration capacity 10000 BTUH x 1 No Power.

Suppying and fixing Cold Room - Freezer of Dimensions (Mtr) EXT 2.5 (D) x 3.04 (W) x 2.44(H) Ambient Temperature + 40 Deg C Room Temperature (-)20 deg C Refrigeration systems and model RUAL0914KP – 2 Nos – ODU RUAL0914KP – 2 Nos -IDU Total refrigeration capacity 9000 BTUH/Hr x 2 Nos

Supplying SS Weighing Scale - 300 kg

Supplying SS Two Sink Unit of Size: 45" X 24" X 34"+6" Sink Size: 18" X 18" X 12" SS 304 Grade Materials

Supplying SS Drain Table of Size: 45" X 24" X 34"+6" SS 304 Grade Materials

Supplying SS Onion & Potato Bin Size: 48" X 24" X 42" SS 304 Grade Materials

Supplying SS Work Table With 1U/S Size: 45" X 24" X 34"+6" SS 304 Grade Materials

Supplying Table Top Model Veg Cutting Machine With Blades 5 Nos

Supplying 20ltr Tilting Grinder 2HP Motor and 3 Phase of Brand approved by Executive Engineer

Supplying Instant Pulverizer 3HP Motor and 3 Phase of Brand approved by Executive Engineer

Supplying Masala Pulverizer 3HP Motor and 3Phase of Brand approved by Executive Engineer

Supplying SS Coconut Scrapper Standing Model 0.5HP Motor and Single Phase of Brand approved by Executive Engineer

Supplying 30Kg Potato Peeler 2HP Motor and 3Phase Supply of Brand approved by Executive Engineer

25Kg Dough Kneader 2HP Motor and 3 Phase Supplyof of Brand approved by Executive Engineer

Supplying SS Masala Trolley 12 Hole SS 304 Grade Materials

Supplying SS 304 Chinese 2 Burner Gas Range Size : 48" X 27" X 30" +18" SS 304 Grade Materials

Supplying SS Single Sink Size: 24" X 24" X 34"+6" Sink Size: 18" X 18" X 12" SS 304 Grade Materials

Supplying SS 304 Double Burner Ras Range Size: 48" X 24" X 24" SS 304 Grade Materials

Supplying SS Single Range Size: 24" X 24" X 24" SS 304 Grade Materials

Supplying SS Bulk Range ( Two Ring Burner) Size: 30" X 30" X 18" SS 304 Grade Materials

Supplying LPG - Bratt Pan 150Ltr SS 304 Grade Materials

Supplying SS Four Burner Range Size: 36" X 36" X 30" +6" SS 304 Grade Materials

Supplying SS Work Table With Sink Size: 45" X 24" X 34"+6" Sink Size: 18" X 18" X 12" HT SS 304 Grada Materials

Supplying SS Rolling Table With Top Granite Size: 45" X 24" X 34"+6" SS 304 Grada Materials

Supplying SS Dosa Dawa - Gas Model Size: 48" X 27" X 34"+6" SS 304 Grada Materials

Supplying SS Batter Trolley Size: 18" X 24" X 34" SS 304 Grada Materials

Bar Screen- Manual bare screen for total flow, to remove particles upto 10mm, made of SS 304 with a rackig arm for manual operation,MS,Epoxy coated.

Raw Sewage Transfer Pumps 2 Nos (1 Working + 1 Standby) Horizontal centrifugal type or submersible type of pumps suitable for solids of 10mm and having CI casing, Impeller with accessories, motor of required capacity. Delivery header with valves, NRV and level controller to control the pump ON / OFF, having capacity of 21 m3/hr and discharge head of 10m min. Make : KBL/Crompton / CRI

AIR BLOWERS system inclusive of (1 Working + 1 Standby) 2 Nos.(1W+1S), Duty - To provide required air for biodegradation in MBBR tank & required air for collection mixing. Type- Twin lobe compressor . Flow -650 m3/hr at 4.5 mwc – 2 Nos. Motor -To be provided with adequate HP & Low RPM. Accessories - Suction and Exhaust silencers, NRV, Pulley,Base frame, Belt guard, etc. Make : Usha Compressor with Siemens/Crompton Motors

Anoxic tank mixer–1No.submersible type with suitable hp motor, MOC – CI with retrievable system for mixing influent sewage with return sludge. Make CRI/Equivalent

MBBR Tank Air Grid / Diffusers- To provide oxygen required for bio degradation. Diffused coarse aeration. diffuser of suitable size, support grids, air headers, fixed type with fittings of suitable size and MBBR media retaining strainer / sieves of UPVC/GI, for MBBR tank.

MBBR - Bio Mass Carrier Media - To provide required surface area for microbial growth. Fludisable or Moving .non clogging type. Moving Bed Bio Reactor Biomass carrier media of suitable size, having Sp.surface area of 350-400 sq.m / m3, MOC of PP/Plastic.

Secondary clarifier mechanism - To separate the bio sludge from MBBR treated water. Size 7.0mdia, MOC: MSEP- Feed well, racker arm, scrppers ,motor G/B etc.

Sludge transfer pumps 2 Nos (1 working + 1 stand by) horizontal centrifugal, coupled centrifugal,Non - clog, capacity of 35 m3/hr, 10 m CI, Make : KBL / CRI.

Disinfection system Disinfecting Hypo Dosing system consisting of electronic metering dosing pumps 2 Nos (1W + 1S) with 200 lit 1 No - HDPE chemical storage tank. Make : Focus

Filter Feed Pumps - 2 Nos (1 working + 1 stand by) pump capacity of 25m3/hr, 30mwc, to feed treated effluent from clarified water tank through filters to treated water tank. Horizontal with accessories,Level switches etc. centrifugal monobloc with suitable HP.Make Kirloskar / CRI

Dual Medical Filter Dual Medica Filter - 1 No, size min.1.5m Dia x 1.5m HOS with necessary accessories complete MS with Butterfly valves, Pr, gauge at inlet and outlet of filter, vessel made of MS fabricated out of 6mm thick, with 8mm dish with two coats of anti - corrosive epoxy painting inside and one coat of red oxide and layer of finishing paint outside, with under bed, support medica & multi-grade filter media to suit the requirement - pebbles and crushed gravels etc., complete as per the standards. filtering Media : Sand & Anthracite.

Activated Carbon Filter To remove trace organics. Vertical type , Flow rate 21 m3/hr , Size -1500 dia x 1500 HOS. MOC -MSEP. Internal Painting -Two coats of anti-corrosive epoxy paint. External Painting -One coat of red-oxide and a layer of finishing paint. Shell & Dish Thickness -6 mm & 8 mm , Frontal piping -MS with Butterfly valves. Pr Gauges -2 Nos. Supporting Media -Pebbles & Crushed gravel , Filtering Media -Activated Carbon.

Inter connection piping, fittings, valves connecting all tanks ,pumps, filters ,etc. GI-class-B/UPVC/MS .Make : GI – Astral/Supreme /tata/Jindal / Equi.

Electrical Panel 1 No. LT non compartmentalized, Wall mounted Panel, Common comprising accessories like Switch fuse units with Multi Function Meter, Switch / Phase indicating lamps, out going starters MCBs, DOL starters & ON /Off push buttons with power and control cable including cable termination, Earthing. Automatic level Controller for actuating Raw Sewage pumps and Filter Feed Pumps to be provided. Necessary power wiring by PVC insulated cu wire in conduit from LT panel to equipment motors shall be provided with necessary support. For UF System: Common Control Panel provided for Auto Operation of UF System along with STP. Components of the control board shall be Siemens / L & T /Equi make.

Electro Magnetic Flow Meter Electromagnetic Flow meter of suitable size for sewage quantity monitoring, One meter shall be installed at sewage transfer pump outlet and another meter at filter outlet. Make :Frehnig/Aster/Equi

Instrumentation Electro magnetic Flow meter of suitable size for sewage quantity measuring, One meter shall be installed at sewage transfer pump outlet and another at filter outlet. Make :Frehnig/Aster

Sludge dewatering system -To separate the biosludge from treated water. Recessed Plate type, Screw Feed pump-1 No, FRP Tray, Filtering Cloth, Hyd Closing etc Make -Flucon/Equi

UF Filtration Feed pumps - 2 Nos (1 working + 1 stand by) capacity of 10m3/hr, 20 mwc, to filtered effluent from treated water tank through UF system, Horizontal centrifugal monobloc pumps, CI construction, coupled to adequate motor, mounted on a common base frame with necessary header, isolation valves on suction and delivery with Pr.gauge with valve tee and fittings with tank level float type high / low level switch Make : Kirloskar.

UF -Chemicals dosing (1 W)Capacity 100 lph Head 2.0 kg/cm2 Type Diaphragm Dosing tank capacity 100 liters MOC of the tank LDPE Make of the Pump Focus /edose ; CEP-NaoH Dosing (1W) Capacity 100 lph, Head 2.0 g/cm2 Type Diaphragm Dosing tank capacity, 100 liters MOC of the tank LDPE Make of the Pump Focus /edose i( at STP Panel) Level switch -Type Float switch

UF Back Wash Pumps. 2 Nos (2 working) suitable capacity, of submersible/horizontal pumps, in.2503/hr,head-2.0 kg/cm2, MOC: CI construction, coupled to adequate motor with necessary header, isolation valves on suction and delivery with valve tee and fittings Make : Kirloskar/CRI.

Garden water transfer Pumps. 2 Nos (2 working) suitable capacity, of submersible/horizontal pumps, min.15m3/hr,head-4.0kg/cm2, MOC; CI construction, coupled to adequate motor, mounted on a common base frame with necessary header, isolation valves on suction and delivery with Pr. gauge with valve tee and fittings with tank level float type high / low level switch Make : Kirloskar/CRI.

Toilet Flushing - UF Treated Water transfer pumps. 2 Nos (2 working) suitable capacity, of submersible/horizontal pumps, min.15m3/hr,head-5.0 kg/cm2 CI construction, coupled to adequate motor, mounted on a common base frame with necessary header, isolation valves on suction and delivery with Pr. gauge with valve tee and fittings with tank level float type high / low level switch Make : Kirloskar/CRI.

Operation and maintenance for 1 year from STP use with chemicals, consumables, operators

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and fixing of 4’20W LED Tube Light for Fitting complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.( Make: Phillips/ Havells or equivalent)

Supply and fixing of Twin Box type 4'20W LED fitting (Phillips/ Havells) complete with TW round blocks on wall or ceiling with 2 Nos 20W LED tube with PVC unsheathed Copper leads from terminals to the fitting. (Make: Havells make Regal Patten for LED tube] REGAL BATTEN T8 UPTO 2 x 22W 4 Feet LED Fitting )

Supply and fixing of Twin Box type 4'20W LED fitting (Phillips/ Havells) complete with TW round blocks on wall or ceiling with conduit pipe suspension with 2 Nos 20W LED tube with PVC unsheathed Copper leads from terminals to the fitting. (Make: Havells make Regal Patten for LED tube REGAL BATTEN T8 UPTO 2 x 22W 4 Feet LED Fitting )

Supply and fixing of Havells make Surface Round (EDGESURFACERDDLR18WLED865S) fitting on ceiling with necessary connections. ( Philips / Havells/ Equivalent make).

Supply and fixing of 42W LED 2x2 (Make : Havells, Model No: PLANOSUR2X2PLS42WLED857S0720) surface type fitting with LED complete on wall or ceiling with PVC unsheathed leads from terminals to the fitting.

Supply and fixing of 42W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of FIxed Spot Light ( Havells Make: UNECO FIXED DOWN LIGHT-15W) Recessed type Fitting on false ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of Bakelite battern holder with 15 W CFL Lamp (Philips make) for BH point.

Supply and fixing of 50W 3000K Warm White monocoloured LED Flood light with special type MS Angle and Clamp on wall with suitable necessary connection. (Philips/Havells/Equ)(Entrance Arch Pillar and Building Column for illumination)

supply and fixing of 80W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of LED Gate Light Fittings -45W (havells Make , Model: CORALPT45WLED757PSYMTOPC (Higher End Philips/Havells) on the existing post/wall with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads MS clamps and aluminum painting.

Supply and fixing of Slimmy Torch Bollard [Dimension : Ø106 x 975mm] 24W LED with Bolt & Nuts Model ID KP9205 arangements with necessary clamps. (Make: K Lite only)

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of Ceiling fan Box Heavy Duty with suitable alignment in the Ceiling Concrete Roof.

Supply & Fixing of 450mm wall mounting air circulator fan on the wall.

Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete with necessary wall opening and making of the wall.

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep light duty AC Exhaust fan.

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End. ( Wall Mounted fan and others-3M)

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.(6 Module)

Supply and fixing of 3nos.6/16 A two module 5 pin socket , 3 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 2 no. 6A two module socket, 2no.6/16 A two module socket , 2 nos. 6A one module switch, 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End(12 Module)

Supply and fixing of 25A Flush type Wall Socket 25A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.

Supply and fixing of Three phase Seven Segment type 4 way 63A distribution board with Metal Door cover Code IP42 Protection , with 63A 4 pole MCB as incoming and Sub incomers 3 Nos 40A DP ELCB and 12 Nos 6-32A SPMCB as Outgoing on Wall with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Hager/legrand) (Lighting Purpose)

Supply and fixing of Three phase Seven Segment type 6 way 63A distribution board with Metal Door cover Code IP42 Protection , with 63A 4 pole MCB as incoming and Sub incomers 3 Nos 40A DP RCCB and 18 Nos 32A SPMCB as Outgoing on Wall with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Hager/legrand) (For 15A, 6 Module and 12 Module Plugs)

Supply and Fixing of 8way 125A Vertical TPN Distribution Boards (with MCCB Incomer); Double Door; IP43 with 1 No 125A 4 pole MCCB as incoming and 4 Nos 63A TP MCB and 12 Nos 6-32A MCB as outgoing on wall with Earth connection only. The MCB DB and MCB's should be with ISI mark. (For Three phase and Ductable AC)

SSupply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.(For Lift-4 Nos)

400A PANEL(Quarters Power):- Design, Supply, erection, testing and commissioning of 400A floor mounted cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s Incomer &outgoing units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4 Nos. of 2” X ¼ ” tinned copper bus bar for 3 phases and neutral (50mm x 6mm) and 2Nos. of earthing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum cree page distance and supported on MS Base channel frame work of size 7'X 2'X ¼”–1Set Incoming 1)Supply and fixing of 400A 4pole MCCB with spreader link and rotary handle -1No Outgoing 1)Supply and fixing of 160A 3Pole MCCB with spreader link and rotary handle—07Nos 2)Supply and fixing of 250A 3Pole MCCB with spreader link and rotary handle—02No Inter connecting the all LT MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve colour coding of phases and neutral indication. Double Earth connection of the MCCB’s to earth bus colour coding of phases and neutral indication. Double Earth connection of the

MCCB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 1 set of supply and fixing Electronic Multifunction Meter class 0.2S flush mounting L&T or equivalent make. Supply and fixing of danger board withSiemens grey powder coating with super Scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting, testing and commissioning(L&T, C&S, SIEMENS, ABB) ( CSSD)

Supply and fixing of 32A TPNMC switch on suitable angle iron frame work with Ms cable entry box with earth connection only

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing. (For Lift)

Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing.(X-ray,MRI and CT Scan)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.(for 5 A Plug and Call bell)

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion. (For 15A Plugs and 6M )

Supplyandrunof2of4sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100VgradeinsuitablePVCrigidpipeconcealedinwallandceilingwithcontinuousearthwireconnectionof4sq.mmcopperwireandmakinggoodof the concealed portion with suitable colour.. (For 9M, AC Plug, and 12 M Power Plugs)

Supplyandrunof2of6sq.mm.PVCinsulatedSCunsheathedFRLScopperconductorof1100VgradeinsuitablePVCrigidpipeconcealedinwallandceilingwithcontiinuousearthwireconnectionof6sq.mmcopperwireandmakinggoodof the concealed portion with suitable colour.( For SPDB)

Supply and Run of 2 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position

Supply and run of 4 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position. (From 400A Essential Power Panel from all floors to 6 Way 7 segment DB in all the floors )

Supply and Laying of 3 core 4 Sqmm copper armoured cable LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For Bollard Light )

Supply and run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6sq.mm copper wire and making good of the concealed portion with suitable colour.(From 400A Non - Essential Power and Essential Panel from all floors to 6 Way 7 segment DB in all the floors )

Supply and run of 4 of 25 sq.mm (168/0.45) PVC insulated SC unsheathed Cu Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 10 sq.mm copper wire and making good of the concealed portion with suitable colour (From 400Am Power panel to 8 Way TPN Vertical MCCB in all the floors )

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For Street Lights)

Supply and clarnping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.(For Street Light post clamping on post for 2 mtr each post)

Supply and fixing of the 4x16 sqmm brass cable gland for the 4x16 sqmm PVC Armoured LTUG cable with earth connection.

Supply and providing cable end termination of 4x16 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and clarnping of 3-1/2 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.(For Lifts)

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection. (For Lift)

Supply and providing cable end termination of 3-1/2x25sq.mm.PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and clarnping of 3-1/2 x 185 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.(From MV Panel to 250A Lighing panel in Kitchen, MV panel to Nurse Quarters, MV panel to Fire Fighting, MV to Pump.)

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2x185sq.mm.PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good((From MV Panel to 250A Lighing panel in Kitchen, MV panel to Nurse Quarters, MV panel to Fire Fighting, MV to Pump.)).

Supply and Laying of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good..(From MV Panel to Power Panel in Kitchen and Nurse Quarters)

Supply and Laying of 2 runs of 3 1/2 x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(From HT Room to Power Panel of Kitchen Block)

Supply and clamping of 2 Runs x3 ½ x 240 sq.mm PVC LT UG cable on wall with M.S clamps.

Supply and fixing of brass cable gland for 3-1/2 x 240 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3-1/2x240sq.mm.PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of 40A FP MCB isolator in Metal box FP enclosure in flush with wall and making good of the concealed portion with earth connection. (Legrand (MDS)/ Hager (L&T) make)

Supply and fixing of 63A FP MCB in Metal box FP enclosure in flush with wall and making good of the concealed portion with earth connection. (Legrand (MDS)/ Hager (L&T) make)

Supply and fixing of 63A FP MCB with SMC box (Legrand make) open in flush with wall with painting with necessary connection.

supply and run of 25mmx3mm tinned copper flat with nessary clamps/supports on Wall/floor/ ground for earth connection. (Panel earthinh and Panel to Ground earthing, Lift Well- 08 Nos)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mmx 50mmx 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, Erection, Testing, Commissioning and Handing over of 1No 20 Bed Cum Persons Passenger Lift as per following technical specifications including all taxes and duties Technical Specifications: 1. Location:Kitchen Block, Chennai-32. 2. No of Lift: Two Nos. 3. Type of Lift: Gearless with Machine Room. 4. Capacity of Lift :20 Persons Bedcum Passenger Lift. (1360Kgs) 5. Speed: 1.50 mtr / Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F with enhanced ride comfort and near zero leveling functions. VVVF Drive. 7. No of floor: Ground + 1 floors. 8. Total Travel: 8.4 mtrs approximate 9. Leveling Accuracy: High level accuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel hairline finish No.4 hair line finish & panels with Direct lighting and New Beautiful Single Tile false ceiling with Tubular Handrail and mirror. 11. Position of Machine: Directly above the lift well shaft gearless. 12. No. of Landing Entrance: One in front - 2 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel operated centre opening SS cars. 15. Landing Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel Power operated V3F Drive Centre opening stainless steel No.4 Hair line finish with view panel . door with provision for emergency key opening at all landing. 16. Car size: 1600mm widex 2400mm deep (part 1) 17. Car clear Opening: 800mm x2000mm (as per IS 14665 (part 1) -2000 (wide) x 2000mm Height. (as per IS 14665 (Part-I)-2000). 18. Lift well : 2800mm(width)x2050mm (depth) available size 19. Lift pit depth available: 1600mm 20. Power supply : 415V,400/440v, 3 phase, 50 cy / Sec A.C supply for power and 230V, 50 Hz single phase AC supply for light. 21. Control: Micro processor Computer based - simplex collective full collective logic system with or without attendant mode.

22. Car fittings:Indirect fluorescent light & Fan. 23. Lift Well: RCC construction with Brick masonry existing. 24. Lift Machine Room: As per standard specification 1800mm (Width) x 1500mm(depth) (as per IS 14665 (Part-5) - 2000) 25. Induction: Up / Down Digital Direction scroll type and position indicator for all landing and in car. 26. Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automatic charging device. 28. Fireman's switch: To be provided at ground floor. 29. Minor Builders Work: To be provided by lift contractor. 30. Scaffolding: To be provided by lift Contractor. 31. Stainless Steel still angles and facia Plates: To be provided by lift contractor. 32. Steel for lift Machinery: To be Provided by lift contractor. 33.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarntee period of one year 34. Provision of 1+3 EPABX intercom with phone to be provided at the following places vide 1. Lift Head Room 2. Reception Room and 3. Inside the Lift by lift contractor. 35.Lift License: Preparation of drawing , payment of charges to CEIG and insurance policy if any and obtaining CEIG safety certificate and lift license as per lift act should be done by the lift contractor. 36. Automatic rescue device: To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger inverter under voltage protection system etc.

24. Emergency Light : Battery Operated Light to be provided with automatic charging device. 25. Fireman's Switch: To be provided at Ground Floor 26. Minor Builders Work : To be Provided by lift Contractor 27. Scaffolding : To be Provided by lift Contractor. 28. Stainless steel still angles and facia plates: To be provided by lift contractor. 29. Steel for Lift machinery : To be Provided by lift contractor. 30. Servicing and Maintenance : Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarntee period of One Year. 31. Provision of 1 + 3 EPABX intercom with phone to be provided at the following places vide: 1. Lift Head Room 2. Reception Room and 3. Inside the Lift by Lift Contractor. 32. Lift License : Preparation of drawing , Payment of charges to CEIG and insurance policy if any and obtaining CEIG safety certificate and lift license as per Lift act should be done by the lift contractor. 33.Automatic rescue device : To facilitate the landing of the nearest floor at the time of power failure . 34. This shall consist of suitable type battery system with charger inverter under voltage protection system etc., .Special Inclusions: 1. Call Register Signal and Vf Door Operator 2. Push Button - Orange LED Illumintion. 3 Full Car Operating Panel 4. Floor Annunciator 5. provision for CCTV Camara - Analog (Coaxial Cable) 6.. False Ceiling In Car 7. Fire Rating Of Landing Doors - Two hours 8. Infra Red Door Screen 9. Overload Warning Indicator 10. Pit Ladder 11.. Ss Handrail 12. Sill Support 13. Landing Push Box On Wall.

Supply of 15KVA (three phase input / single phase output ) microprocessor controlled double conversion true online ups system with builtin isolation transformer, auto phase sequence correction, power factor correction, builtin manual bypass arrangement with exide sealed maintenance free batteries for 2 hours backup time with suitable interlink cables and ms powder coated rack for batteries CONFIGURATION: True On line double conversion ups system with pulse width modulation (PWM) Technology using IGBT inverter. RECTIFIER: Full wave (shall fully meet the specified input power requirements ) INPUT: 3 phase 320V – 460V OUT PUT:230V +1% on battery mode FREQUENCY: 47HZ-53HZ SYSTEM DC VOLTAGE: 360V INVERSION TECHNOLOGY: Micro processor controlled, pulse width modulation with Instantaneous sine Wave control using IGBT. INVERTER OUT PUT : ( Out put Galvanic Isolation through Double winding Isolation Transformer at Output of Inverter shall be part of UPS Design ) LOAD POWER FACTOR: 0.8 to lag to unity REGULATION : for Balanced load + 1% For 100% unbalanced load + 2% FREQUENCY: 50Hz + 0.5% WAVE FORM : True sine wave TOTAL HARMONIC DISTORTION : Less than 5%

OVERLOAD CAPACITY: Inverse Time Characteristic 125% for 10 minutes 150% for 1 minutes EFFICIENCY : 1. Converter – 90% 2.Inverter - 85% 3. Overall – 80 % ( full load) OPERATING TEMPERATURE : 0 to 45 Degrees centigrade on full load CREAST FACTOR: 3 : 1 RELATIVE Humidity : : 95% at 35 Degree Centigrade non- Condensing CHARGER: Built in solid state automatic float- cum boost charger with constant current, constant voltage mode of charging along with current limiting features. Ripple in DC shall not exceed 2% when battery is disconnected. PROTECTION( in built) i) output under Voltage ii) output over Voltage iii) ) output over load iv) output short circuit. v) HRC fuses /output/ battery vi) Battery low trip vii) battery charges current limit. (Opeartion theatre-1,2,3, 4 and EOT)(ICU)

Supply and Installation of copper 18 mm Copper Rod size of 8 feet length buried in earth including excavation of earth upto the depth of 8 feet and closing the pit. Fill with bentonite 25 kgs chemical and including PVC pit cover.

Supply and Installation of copper air terminal spike arrestor with base and all fittings.(MR)

Supply and installation of 70Sqmm Copper Cable run on the external wall from terrace to the ground floor in PVC 1" Conduit.

Supply and fixing of Aviation lamp for the Security purpose of the Multi storage Buildings Placing at the top of the Building with suitable necessay connection. (Bajaj/Equ)

Design, supply, erection, testing and handing over of High Mast Structure (16 Metre height) Valmount/Bajaj/ Philips/ make or equivalent with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 16 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 8 Nos.150W of flood light luminaries with control gear box complete head frame assembly, Pulley drive, stainless steel wire rope single/double drum self lubricating winch arrangement suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast. a) Design and casting of suitable foundation with 1:2:4 mix RCC concrete with 30 cm projection above the ground level with 1 metre Width x 1 metre Length and 2 metre

depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site- 1 set. b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitablefor 3 phase 415 V 50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch - 1 Set d) Neon aviation obstruction light (Bajaj BJAOL (2) / equivalent - 1 No. e) 2 Nos of special GI earth electrodes with copper plate 300 x300 x 3mm and copper flat (1”x1/4”) interconnection as per ISS complete with earth connection - 1 set. f) Hot dip galvanized lightening arrestor-1 No. g) Flood light luminaries of specially Heavy type water poof Dust proof integral luminaries fitting provided with 150 Watts LED Light fitting Crompton / Philips make or Equivalent with, Alglas coated reflectors, with cable connection etc: complete as per standard specification-8 Nos.

Erection of the High mast by providing concrete 1:1.5:3 mix R.C.C masonary foundation pedestal. The RCC pedestal projection should be 30cms above the ground level. The feeder pillar box should also be mounted in RCC pedestal with projection of 30 cms above the ground level & foundation suitable to the safe bearing capacity of the soil at 12T /M2 at 1.8m depth of below ground level and necessary galvanized foundation bolts nuts washers and Anchor Plate & Template etc., complete as per standard specification of IS-875-1987.

Supply and fixing of 0.7mx Height 1Mt x Width 0.4mt floor mounting type Pillar Box made up of 16SWG CRCA sheet steel with one coat of primer and two coats of painting in suitable masonry pedestal and AI frame work with one no Danger board an supply and fixing of following switches with earth connection and necessary identification of danger letter in BOLD i) Supply an fixing of One no 4way Double Door Vertical IP 43 Protection MCCB DB in with 1No X63A MCB FP as Incoming and 6nos 32-40A TPMCB with necessary cable entry boxes with suitable earth connections along with Automatic timer arrangements like L&T/Siemens/MDS/Hager. (Pillar box for Highmast with Timer)

Single Bracket Stree Light: Supply and erection of G.I. Stepped tubular pole of 8 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm) 114.30mm OD x 5.40mm Thick x 4500mm Length, 88.90mm OD x 4.85mm Thick x 1750mm Length, 76.10mm OD x 3.25mm Thick x 1750mm Length, with single arm ornamental bracket of outer dia 50 mm pipe bent suitably to give a height of 1.5 mtr and overhang welded suitably with ornamental bracket and fixed rigidly with 8 Nos of bolt and nuts to prevent any turning movement of bracket due to wind with sheet moulded compound (SMC) junction box IP 42 protection of size (295mm x 225 mm x 120mm) , fire proof of suitable size with 4 way terminal block with hylem sheet of size (250mm x 200mm x 6mm) with 1 No. 16 A fuse unit with 1 No. suitable links provided at a height of 2.0 mtr from the ground level with embossing of metalic "DANGER 440 V" with earth connection with earth bolts of size 8mmx25mm welded on the pole at one end with 4 mtr of 40 mm PVC pipe for incoming and outgoing cable. The pole shall be provided for coil earth with No. 8 for coil earth with No. 8 SWG GI wire of 11.5 mtr of length in which 10 mtrs of total length compressed in to a coil of one meter length. The pole shall be painted with one coat of red oxide primer paint and two coats of aluminium paint of reputed make to the length of pole with supply and fixing of 150W LED street light with necessary connection wire from junction box to the fittings with 3 x 1.5 sq mm PVC copper wire for each fitting with pole earthing with necessary connections testing and commissioning as per the specification. The pole should be mounted on the special type of bracket which would be fixed on the side of the crash barrier and the details are as follows The bracket should be fabricated like diagnal cut of the cubic structure with 25 mm thick plate of size

The bracket should be fabricated like diagnal cut of the cubic structure with 25 mm thick plate of size 425x400x25mm with 8mm thick stiffner plate for side support and providing 8 Nos 25 mm hole for fixing the bracket on wall with special flange on the other side of barrier, with necessary M14 and M16 bolt with spring washers, nuts etc.,

Double Bracket Stree Light: Supply and erection of G.I. Stepped tubular pole of 8 Metre Length Single Ornamental Bracket Pole with Base Plate (250 x 250 x 6mm) 114.30mm OD x 5.40mm Thick x 4500mm Length, 88.90mm OD x 4.85mm Thick x 1750mm Length, 76.10mm OD x 3.25mm Thick x 1750mm Length, with Double arm ornamental bracket of outer dia 50 mm pipe bent suitably to give a height of 1.5 mtr and overhang welded suitably with ornamental bracket and fixed rigidly with 8 Nos of bolt and nuts to prevent any turning movement of bracket due to wind with sheet moulded compound (SMC) junction box IP 42 protection of size (295mm x 225 mm x 120mm) , fire proof of suitable size with 4 way terminal block with hylem sheet of size (250mm x 200mm x 6mm) with 1 No. 16 A fuse unit with 1 No. suitable links provided at a height of 2.0 mtr from the ground level with embossing of metalic "DANGER 440 V" with earth connection with earth bolts of size 8mmx25mm welded on the pole at one end with 4 mtr of 40 mm PVC pipe for incoming and outgoing cable. The pole shall be provided for coil earth with No. 8 for coil earth with No. 8 SWG GI wire of 11.5 mtr of length in which 10 mtrs of total length compressed in to a coil of one meter length. The pole shall be painted with one coat of red oxide primer paint and two coats of aluminium paint of reputed make to the length of pole with supply and fixing of 2 Nos of 150W LED Street light with necessary connection wire from junction box to the fittings with 3 x 1.5 sq mm PVC copper wire for each fitting with pole earthing with necessary connections testing and commissioning as per the specification. The pole should be mounted on the special type of bracket which would be fixed on the side of the crash barrier and the details are as follows The bracket should be fabricated like diagnal cut of the cubic structure with 25 mm thick plate of size

The bracket should be fabricated like diagnal cut of the cubic structure with 25 mm thick plate of size 425x400x25mm with 8mm thick stiffner plate for side support and providing 8 Nos 25 mm hole for fixing the bracket on wall with special flange on the other side of barrier, with necessary M14 and M16 bolt with spring washers, nuts etc.,

Supply, Erection, Testing, Commissioning and Handing over of 1 No 250 KVA Diesel Generator with AMF Panel set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 600 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter(pre and micro) 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Mufler 14. Fly wheel with starter ring.

ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator. SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device 1. Low lubricating oil pressure 2. High Water temperature 3. Vee-belt failure and over speed 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load. 2. ALTERNATOR : Alternator capacity of 250 KVA/ 200 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.) 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole

within 0.1mm Powder coating done after seven – tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if

any World class Cooling package: Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade. 4. FUEL TANK : 350 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. 5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges. 6. Battery: 2 Nos 12V 180AHR Battery (Ashok Leyland/Cummins/Kirloskar or Equivalent) (Kitchen)

Supply of lubricating oil and first filling with charging of starting battery and supply of 210 Ltrs diesel for 250 and 2 Nos of 500 KVA Generator to run the geneset for minimum of 8 hours testing again handed over to occupied depatrment.

Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ceiling with connection (For AMF to 250KVA Genset)

Preparation of site plan physical layout electrical schematic diagram in 5 sets , getting drawing approval from CEIG preparation of completion report, rectification report and arranging CEIG inspection and obtaining CEIG safety certificate preparation of 2 sets of approved drawing and a copy of safety certificate in a neat frame work to be fixed in Generator room and payment of CEIG inspection 250 KVA Genset

Charges for the Preparation of samples and letters for the Quality testing Certificate to the Electrical materials used in construction purpose for this Project campus for PVC conduit pipes, Electrical Wires, Distribution boards, MCB's, MCCB's and Switches, Sockets and LTUG Cables from the Central Electrical Testing Laboratory, kakalur lab/National Test House, Tharmani.

Supply, Erection, testing and commissioning of 11KV 25 KA630Amps 3 Panel HT Indoor RING MAIN GEAR panel board suitable for Indoor installation comprising two incomer panels with Air Break/ load Breaks switches and one outgoing panel with Vacuum Circuit Breaker complete as per TANGEDCO specification with Mechanical inter lock between incomers. 1. Supply and Erection of Draw out type 11KV 25KA 630Amps Horizontal draw out / Horizontal Isolation VACCUM CIRCUIT BREAKER filled with motor(230V AC) operated spring charged Mechanism, with ON and OFF mechanicalIndicator Anti Pumping Device, 110V DC Shunt Trip and Closing Coils (DC source of supply to be derived from a power pack suitable for three Tripping and two closing operations incorporated on Incoming panel only) Mechanical Operation counter, 4NO + NC Spare Aux. Contact with contact multiplication Contactor for customer use. Automatic safety shutter, Mechanical close/Trip Knob, Mechanical ON/OFF Indication, Operating Handle, 230V AC to 110V DC Power pack operating Handle etc.-1No Operation counter, 4NO + NC Spare Aux. Contact with contact multiplication Contactor for customer use. Automatic safety shutter, Mechanical close/Trip Knob, Mechanical ON/OFF Indication, Operating Handle, 230V AC to 110V DC Power pack operating Handle etc.-1No mechanism , 2 NO+ 2NC Aux. Contact operating handle etc.-1No. 2. Supply and erection of 11KV 630Amps 25KA HT Air Break/Load Break Switch with mechanically inter locked earth switch, front operated spring assisted manual closing 3. 11KV/Root 3/110V/Root3-Three Phase 3 Limb 50VA class0.5 Resin cast Draw out type potential Transformer complete with HT and LT HRC fuses with sealing arrangement-3 Nos. 4. Current Transformer of Suitable Ratio/5-5A dual Core (Core 1-5VA Class 0.5 for Metering & Core 15 VA 5P 20 for Protection - 3 Nos

7)Breaker ON/OFF/Auto Trip/Healthy/Spring Charged Indication Lamp LED Type 8) Phase Indication Lamps R,Y,B(Incomings 3 Nos) 9) Control Wiring 10) 800Amps Copper Bus bar PVC Sleeved and required panel copper earthing. 11)Control switch TNC (Incoming-1No, Outgoing -1No) 12)Trip Circuit healthy Push Button(Incoming-1 No, Outgoing -1No) 13)Common for Switch gear, MCB's for AC DC Control, Heater ON/OFF Switch with space Heater and thermostat Single phase switch socket, cubicle illumination lamp, Disconnecting type terminal Block.etc., 14)MS Sheet enclosure for Indoor Installations Powder coated with Paint shade Siemens paint finish provision through Bottom entry to receive Incoming and Outgoing cable excluding cable glands and cable termination etc.,

Supply and laying of 11KV 3 Core 300 Sqmm XLPE UG cable in a trench to be excavated at a depth of 1.0 mtr. Putting 0.15 mtr. Layers of sand covering the HTUG cable completely with cement concrete RCC cable turf and refilling the earth to make good (From RMG to Single panel HT VCB , Single panel HT VCB to 5 Panel HTVCB incoming and 5 Panel VCB to 3 Panel VCB).

Supply and clamping at 11KV 3 core 300 sq.mm XLPE UG cable on wall with M.S. special clamps.

Supply and providing cable end termination suitable for 11KV 3 core 300 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shinkable joint kit and accessories. Make: RayChem / M.Seal. ( RMG-3Nos, SP VCB-2 Nos and 5 panel HTVCB-1No, 5 panel VCB-01 no and 3 Panel VCB -01no)

with Highest inst. Elements similar like Megawin type MCDG 61. (Incoming 1 No) 6) TP ND IDMT 2 OC + 1 EF Relay similar like Megawin type MCDG31 Master trip Replay Megawin MVAJH 13 (Incoming 1 No.Outgoing 3 No) 7) Breaker ON/OFF/Auto Trip/Healthy Trip/Spring charged Indication lamp LED type (Incoming 5 Nos. Outgoing 5 Nos.) 8) Phase Indicating Lamps R,Y and B (Incoming 3 Nos) 9) Control Wiring 10) 800Amps Aluminium Bus Bar PVC sleeved and required panel copper Earthing. 11) Control Switch TNC (Incoming 1 No. Outgoing 3 No.) 12) Trip Circuit Healthy Push Button (Incoming 1 No. Outgoing 3 No.) 13) Common for Switch gear, MCB's for AC DC Control, Heater ON/OFF Switch with space Heater and thermostat single phase switch socket, cubicle illumination lamp, Disconnecting type terminal Block etc. 14) MS sheet enclosure for Indoor Installation Powder Coated with paint shade siemens Grey, paint finish Provision through Bottom entry to receive Incoming and Out going cable excluding cable glands and cable termination kit. (Make : system control / Megawin / / ABB/ Siemens /or Equivalent

Supply and clamping at 11KV HT 3 core 240 sq.mm XLPE UG cable on wall with M.S. special clamps (From HT Panel to 1000 KVA Transformer 1&2 primary side

Supply and providing cable end termination suitable for 11KV 3 core 240 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shinkable joint kit and accessories (Make:RayChem/M.Seal.( 5 panel HTVCB-2Nos &1000KVA Tr.1&2-2Nos and 500 KVA trs1 &2-2 Nos )

Supply, Erection, Testing and Commissioning of 1000 KVA transformer OLTC with RTCC Panel,11KV/0.433V Dyn11,ONAN, Indoor Type, double wound, Energy Efficient Transformer with ON Load Tap Changer. distribution transformer confirming to relevant IS.1180 Level-2 and fitted with the following. 1.Rating &connection diagram plate 2.Earthing terminal 3.Lifting lugs for whole Transformer 4.Cover lifting lugs 5.Oil level gauge-plain with level marking 6.Bottom filter cum drain valve with plug 7.Top filter valve with plug 8. pocket for Thermometer 9.Oil Conservator with drain plug 10.Oil filling point with cap on the conservator 11.Air release plug 12.Silicagel breather 13.Monogram plate 14.Explosion vent with diaphragm 15.Transformer oil 16.Under base channel with skids 17.Oil temperature indicator with A/T Contacts

18.Winding temperature indicator with A/T Contacts 19.Marshaling box 20.Bi-directional rollers. 21.Buchholz relay with A/T Contacts 22.DetachableRadiators. 23.ON circuit tap switch 24.Conservator shut off valve 25. Neutral CT Special accessories The transformer should be supplied with first filling of oil Terminal arrangement:- HV-Cable box,LV-Flange to suit bus duct. All removable covers shall be provided with weather proof hot oil resistant, resistance gaskets, to prevent leakage of water in to core, and oil from the tank with Transformer plinth construction of 1000KVA as per IS 1180 (Make CREL/ROWSON /Voltech)

Design, Supply, erection, testing and commissioning of 1600A Copper Bus Ducts made up of 16 SWG sheet steel minimum thickness of 1.8 mm bolted on to an angle iron / structural steel framework.covers the requirements of 3 phase 415 V, 50 Hz, 1600A continuous rated, copper TPN bus with enclosure suitable for indoor type. The bus – duct shall be designed for the above current ratings and for a maximum temperature rise of 400C over an ambient temperature of 45°C. The bus – bars shall be of hard drawn high conductivity electrolytic grade copper flats of size 2Runs x 50x12mm (or)1Run x 100mmx12mm electrical grade 63401-WP as per IS: 5082. The bus- bars shall be of uniform cross section along its entire length. No tapering of the bus bars’ cross-section is allowed. The bus duct shall be painted after suitable pretreatment of all structural steel and plates with anti-corrosive epoxy base primer paint & two coats of anti corrosive epoxy base paint externally with a colour of pebble / flint gray shade RAL 7032and dried in a oven. The enclosure shall conform to IP: 54 for indoor, as per Indian Standards. Inner surface of the bus – duct shall be coated in the rubber paint. The bare bus –bars shall be provided with a coat of Matt finish, The joints in the bus –bars shall be of the bolted type and it shall be ensured that the following precautions are observed. i). The contact pressure must be ample and this shall be maintained during the time the panel is in service. ii) The surfaces of the conductors must be clean. iii) With flat conductors, the overlap should be equal to or greater than the width of the bars or ten times the thickness of the bar whichever is greater iv) The joints shall be treated by the application of joint compound to render the joint moisture-proof. v) For the joints use of bolts of cadmium plated high-tension MS bolts having expansion characteristics due to temperature change similar to the conductor may be used with steel nuts.

vi) Smearing the surfaces with oxide inhibiting grease just prior to making the joint in order to preserve the efficiency of the joints. Minimum phase and earth clearance required shall be maintained at joints. The joints shall be thoroughly shrouded. The bus bar arrangement shall generally conform to IS: 5578 and IS: 11353. The bus – duct shall be also supplied with suitable earth bus running all along the length of the bus – duct made of copper strips. Current density at any part shall not exceed prescribed limits. Two copper flats of same phase shall be stacked together or the spacing between them shall be maximum of the thickness of one conductor. The busbars shall be phase identified by colour, at intervals. Colour code shall be RED, YELLOW and BLUE for phase and BLACK for the neutral bus – bar. hygroscopic, resin bonded self-extinguishing fire retardant insulators preferably of SMC / DMC with ribbed construction to prevent tracking due to dust paths. Bus – bars and supports shall withstand the maximum stresses that are induced in the event of. The short-circuit currents being as specified. The bus – bar support shall be at a minimum interval of 500mm. 5 Deg.C above the ambient. The clearance between the individual bare phase power bus – bars and between the phase and earth bus –bars in air shall be not less than 25 mm and 19 mm respectively.

Design, Supply, erection, testing and commissioning of 1600A capacity Copper Flexible end joints Expansion flexible (30SWG) from Bus duct end to 1600A LTACB termination end and Bus duct end to 1000 KVA Transformer bushing . The bus–bars joints shall be supplied with flexible expansion joints at both the ends and also at bends. The supports and expansion arrangement shall be so chosen to avoid undue stress to the bus – bars, supports and end connections.(TR 1&2-2 Sets,1600A LT ACB 1&2-2 Sets=4Sets)

MV PANEL BOARD:- Design, Supply, erection, testing and commissioning of 3200A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following ACB's & MCCB's 2 Nos.1600A ACB as Incomer units with the following items of work complete to satisfy the latest IS rules and CEIG guidelines. Supply and fixing of suitable size bus bar chamber made up of 16 SWG MS sheet steel with 4 Nos ie R,Y,B,N. 2Runs 4” X 1/2”(2 x 100mm x 12mm) earthing bus of size 2”X ¼ (2 x 50mm x6mm) tinned copper bus on suitable bus bar insulator (Epoxy insulator)With maximum creepage distance and supported on MS Base channel frame work ofsize 4”X2”X¼-1Set(100mm x50mm x6mm) Incoming :1)Supply and fixing of 2 Nos. 1600A basic rating 4 pole 433V LT ACB confirming to IS 13947 – 2 IEC 60947 – 2 for higher breaking capacities of 50KA at 690V AC with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with micro processor SR 18 G relay, over current trip device adjustable to LTD, STD and release for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mould base for each pole for easy maintenance all relevantprotection safety accessories as per CEIG, IE rules inforce with interconnection and terminations as required in specification. BUS COUPLER:- Supply and fixing of 1 No 3200A basic rating 4 pole 433 V LT ACB incoming to IS-13947-21EC60947-690VAC(catno.ST35567 4Pole 75KA)with all accessories for standard horizontal type ACB equipped with micro processor based SR18G.

Outgoing: 1) Supply and fixing of 800A 4 Pole MCCB with spreader link and Extended Rotary handle-2 Nos 2) Supply and fixing of 800A 3 Pole MCCB with spreader link and Extended Rotary handle-4 Nos 3) Supply and fixing of 400A 3 Pole MCCB with spreader link and Extended Rotary handle-4 Nos 4) Supply and fixing of 250A 3 Pole MCCB with spreader link and Extended Rotary handle-4 Nos 5)Supply and fixing of 160A TP MCCB with extended Rotary handle and Spreader terminals -2Nos. Inter connecting the all LT ACB’s and MCCBs to two bus bar with suitable insulated tinned copper flats and painting of phases and neutral indication. Double Earth connection of the MCCBs and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/4” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments with in the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC, 300P class 0.5 Base mounting L&T or equivalent.(Make–Model. ER300P class 0.5) Supply and fixing of danger board with siemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc.Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel,concreting, testing and commissioning (L&T/Siemens/ABB)

Supply and erection of 300 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 18 stage, (at 0.95 lag), made up of powder coated, 14/16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with 800A TPN MCCB as incoming (L&T/Siemens/C&S) with Delta Connected capacitors (BCH/EPCOS) MOO T

ype operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters. a. Vr – R phase Line Voltage b. Vy – Y phase Line Voltage c. Vb – B phase Line Voltage d. Ir – R phase Line current e. Iy – Y phase line current f. Ib – B phase Line Current g. KW – Present Kilo Watts h. RKVA – Present KVAR Demand i. KVA – Present KVA j. PF – Present Power Factor k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load m.Provision to indicate the change in phase Sequence n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection. Make. (Matrix /L&T /or equivalent

with Highest inst. Elements similar like Megawin type MCDG 61. (Incoming 1 No) 6) TP ND IDMT 2 OC + 1 EF Relay similar like Megawin type MCDG31 Master trip Replay Megawin MVAJH 13 (Incoming 1 No.Outgoing 3 No) 7) Breaker ON/OFF/Auto Trip/Healthy Trip/Spring charged Indication lamp LED type (Incoming 5 Nos. Outgoing 5 Nos.) 8) Phase Indicating Lamps R,Y and B (Incoming 3 Nos) 9) Control Wiring 10) 800Amps Aluminium Bus Bar PVC sleeved and required panel copper Earthing. 11) Control Switch TNC (Incoming 1 No. Outgoing 3 No.) 12) Trip Circuit Healthy Push Button (Incoming 1 No. Outgoing 3 No.) 13) Common for Switch gear, MCB's for AC DC Control, Heater ON/OFF Switch with space Heater and thermostat single phase switch socket, cubicle illumination lamp, Disconnecting type terminal Block etc. 14) MS sheet enclosure for Indoor Installation Powder Coated with paint shade siemens Grey, paint finish Provision through Bottom entry to receive Incoming and Out going cable excluding cable glands and cable termination kit. (Make : system control / Megawin / / ABB/ Siemens /or Equivalent

Supply and clamping at 11 KV 3 core 185 sq.mm XLPE HTUG cable in existing trench / pipe laid in ground. (From 3Panel HT VCB to 500 KVA Transformer 1 & 2)

Supply, Erection, Testing and Commissioning of 500 KVA,11KV/0.433V OLTC with RTCC Panel Dyn11,ONAN, Indoor/Outdoor Type, double wound, Energy Efficient Transformer with OFF Circuit type. distribution transformer confirming to relevant IS.1180 Level-1 and fitted with the following. 1.Rating &connection diagram plate 2.Earthing terminal 3.Lifting lugs for whole Transformer 4.Cover lifting lugs 5.Oil level gauge-plain with level marking 6.Bottom filter cum drain valve with plug 7.Top filter valve with plug 8. pocket for Thermometer 9.Oil Conservator with drain plug 10.Oil filling point with cap on the conservator 11.Air release plug 12.Silicagel breather 13.Monogram plate 14.Explosion vent with diaphragm 15.Transformer oil 16.Under base channel with skids 17.Oil temperature indicator with A/T Contacts 18.Winding temperature indicator with A/T Contact Box 19.Marshaling box 20.Bi-directional rollers. 21.Buchholz relay with A/T Contacts 22.DetachableRadiators. 23.Off circuit tap switch 24.Conservator shut off valve 25. Neutral CT 26.OLTC with RTCC Panel Special accessories The transformer should be supplied with first filling of oil Terminal arrangement:- HV & LV Side Cable box, All removable covers shall be provided with weather proof hot oil resistant, resistance gaskets, to prevent leakage of water in to core, and oil from the tank with Transformer plinth construction of 500KVA as per IS 1180 EEL1 (Make ROWSON / Voltech/ IPL or Equivalent)

MV PANEL:2-Design, Supply, erection, testing and commissioning of 1600A floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following switch and 2 Nos.800A ACB as Incomer units with the following items of work complete to satisfy the latest IS rules and CEIG guidelines. Supply and fixing of suitable size bus bar chamber made up of 16 SWG MS sheet steel with Three phases and Neautral (ie) R,Y,B,N. 2 Runs 3” X 1/2” (100mm x 12mm) tinned copper bus bar for 3 phases and neutral and 2 Nos. of earthing bus of size 1”X ¼ (2 x 25mm x6mm) tinned copper bus on suitable bus bar insulator (Epoxy insulator)With maximum creepage distance and supported on MS Base channel frame work ofsize 4”X2”X¼-1Set(100mm x50mm x6mm) Incoming:-1)Supply and fixing of 2 Nos. 800A basic rating 4 pole 433V LT ACB confirming to IS 13947 – 2 IEC 60947 – 2 for higher breaking capacities of 65KA at 690V AC with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with micro processor SR 18 G relay, over current tripdevice adjustable to LTD, STD and release for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mould base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules inforce with interconnection and terminations as required in specification. 2)BUS COUPLER:- Supply and fixing of 1 No 3200A basic rating 4 pole 433 VLT ACB to IS-1394721EC60947-2 600VAC with all accessories for standard horizontal type ACB equipped with Microprocessor based SR18G(w/o protection). Outgoing:- 1) Supply and fixing of 800A TP MCCB with extended Rotary handle and spreader terminal --2Nos 2) Supply and fixing of 630A TP MCCB with extended Rotary handle and spreader terminal --4Nos

3)Supply and fixing of 400A TP MCCB with extended Rotary handle and Spreader terminals --12Nos 4)Supply and fixing of 250A TP MCCB with extended Rotary handle and Spreader terminals -8Nos Inter connecting the all LT ACB’s and MCCBs to two bus bar with suitable insulated tinned copper flats and painting of phases and neutral indication Double Earth connection of the MCCBs and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments with in the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC, 300P class 0.5 Base mounting L&T or equivalent.(Make–Model. ER300P class 0.5)Double Earth connection of the MCCBs and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/8” . Supply and fixing of danger board with siemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc.Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel,concreting, testing and commissioning (L&T/Siemens/Legrand)

Supply and Laying of 3R X 3½ x400 sq.mm PVC LTUG armored cable on post or on wall / existing trench with MS Clamps. (From 2 Nos of 500 KVA Transformer to 1600A MV panel)

Supply and erection of 150 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 12 stage, (at 0.95 lag), made up of powder coated, 14/16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with 630A TPN MCCB as incoming (L&T/Siemens/C&S) with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the necessary electrical and t 1 Set comprising of: have 11 stage APFC with i) 2Nos 25KVAR MPP(H)capacitor each with capacitorduty contactors and 63A TP MCB ii) 3 Nos 10KVAR MPP(H)capacitor each withcapacitor duty contactors and 32A TP MCB iii) 4 Nos 5KVAr MPP(H)capacitor each withcapacitor duty contactors and 32A TP MCB with complete connection etc .

Earthling as per ISI specification with an earth electrode of 2.1m class ‘B’ GI pipe ofdia not less than 40mm, with copper earth plate of size 125mm X 50mm X 6mm withnecessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and providing of maintenance free earthling electrode dual pipe flat technology model maintenance free earth 502 consist of 2mtr long 47mm dia outer pipe with 3.2mm thick 25mm dia inner pipe 2.6mm thick terminal flat of 30x10/12 x 12mm, the entire construction processed with hot tip galvanizing, outer surface up to100 microns all inner annular space filled with highly conductive and non-corrosive nature crystalline material along with electrode moisture booster compound of 1x25 kg bags will be supplied to fill surround the pipe at the time of installation. (Moisure retention, conduction and non-corrosive nature (Galaxy /Ashlok or equivalent) for 1000KVA Tr 1&2=4Nos.

Supply and run of 50mm x6mm (2” X 1/ 4”) copper flat with porcelain insulator with screws on wall/floor for earth connection. (

Supply and run of 25mm x6mm( 1” X 1/4”) copper flat with porcelain insulator with screws on wall/floor for earth connection.

Supply and run of 25mm x3mm( 1” X 1/ 8”) copper flat with porcelain insulator with screws on wall/floor for earth connection.

SUB-STATION EQUIPMENTS:- Supply and Erecting of safety accessories.SR.XIII PART “M” 8 Item (a) to (i) .

Supply, fixing, testing and commissioning of AC Chargeable emergency lamp 2 x 11W PL lamp with all connected accessories (M-1975)

Supply and installation of 2.5mm thick Rubber Mat with ISI suitable for 1.1KV installation confirming to IS 15652 (5Nos=1set)

Supply and Providing approved make First aid box complete with all first aid medicines

Supply and providing shock treatment chart fixed in glass frame (Tamil and English)

Supply and fixing of the 4nos fire buckets stand suitable for 4 nos fire buckets made out of 40 x 40 x6mm MS angle

Supply of hand gloves 11 KV grade

Supply and installation of Danger Board as required by the electrical authorities

Supply and erection of Fire extinguisher Co2, 4.5 Kg confirming to TAC norms

Earth Discharge Rod

Preparation of site plan physical layout electrical schematic diagram in 5 sets , getting drawing approval from CEIG preparation of completion report, rectification report and arranging CEIG inspection and obtaining CEIG safety certificate preparation of 2 sets of approved drawing and a copy of safety certificate in a neat frame work to be fixed in HT/Generator room and payment of CEIG inspection fees for HT and 500 KVA Genset

Supply and laying of 3 ½ x185 sqmm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 Mtr Putting 0.15mt layer of sand and covering the three sides of the cable with bricks and refilling the earth to make good. 1)From Genset Panel 1 to Pump room 2) From MV Panel to STP Room

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 1)From Genset Panel 1 to Pump room-1 2)From Genset Panel 2 to Pump room-2 3) From Genset Panel 2 to St.light pillar

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(From MV panel to ETP Room )

Supply and fixing of brass cable gland for 3 ½ x185 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 ½ x185 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of brass cable gland for 3 ½ x240 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 ½ x240 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of brass cable gland for 3 ½ x50 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 ½ x50 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and fixing of brass cable gland for 3 ½ x35 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 ½ x35 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply of lubricating oil and first filling with charging of starting battery and supply of 210 Ltrs diesel for 250 and 2 Nos of 500 KVA Generator to run the geneset for minimum of 8 hours testing again handed over to occupied depatrment. (1Litre = Rs.100 for 210Ltr = 210*100 = 21000 + 820 Ltr*100 = 82000)

Supply, Erection, Testing, Commissioning and Handing over of 1 No 500 KVA Diesel Generator set of 0.8P.f, Three Phase, 415/420Volts, 50c/s, 1500RPM as detailed below 1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 600 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000. The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent) 1. Dry type Air cleaner 2. Expansion bellow 3. Radiator, Radiator fan and mounting 4. Air to air charge cooler 5. Exhaust Gas turbo charger 6. Lube oil cooler and Lube oil filter 7. Fuel filter(pre and micro) 8. In-line Mono-block fuel injection pump with governor and fuel feed pump 9. Electronic governor 10. 24V Battery charging alternator 11. 24V Volt electric starter motor 12. Engine test Certificate 13. Residential Mufler 14. Fly wheel with starter ring. ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator. SAFETY SYSTEM OF ENGINE :- The Engine shall trip for the following conditions with visual alarm device 1. Low lubricating oil pressure 2. High Water temperature 3. Vee-belt failure and over speed 4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every

11 hours continuous running at full load. 2. ALTERNATOR : Alternator capacity of 500 KVA/ 400 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.) 3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of holewithin 0.1mm Powder coating done after seven – tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG

sets if any World class Cooling package: Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade. 4. FUEL TANK : 350 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance. 5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges. 6. Battery: 2 Nos 12V 180AHR Battery (Ashok Leyland/Cummins/Kirloskar or Equivalent)

Supply and fixing of 800A 4Pole (ATS) Auto Transfer Switch Panel with ATS controller with sheet steel enclosure suitable for 500 KVA Generator set consisting for the following items 1) 800A Auto transfer switch-1No (Hager Make) 2) ATS controller - Hager Make 3) Control Fuse-6A--------------2Nos 4) Control contactor------------1 No 5) Indication Lamp 230 volt-5Nos 6) LVM ---------------------------- 1No 7) Battery charger 24 volt-----1 No 8) Suitable channel ans angle iron frame work including necssary civil work. (MR)

Supply and fixing of 800A Change over switch with suitable angle iron frame work with top and bottom cable entry box with necessary earth connection. (Manual Bypass Switch- 04 Nos of 1 Generator) - total-08 nos

Supply and Laying of 3 run of 3 1/2 x 400 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 1) from MV panel to AMF AND AMF TO 3 NOS OF 500kva DG

Supply and fixing of brass cable gland for 3 ½ x400 sq.mm PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3 ½ x400 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and Run of 12 core 2.5 sqmm armoured copper control cable FRLS in suitable PVC rigid pipe on wall/Ground/ceiling with connection (For AMF to 250KVA Genset)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box on wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End

Supply and fixing of 4’20W LED Tube Light for Fitting complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.( Make: Phillips/ Havells or equivalent)

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete with necessary wall opening and making of the wall.

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep light duty AC Exhaust fan.

Supply and fixing of 2 no. 6A two module socket, 1no.6/16 A two module socket , 2 nos. 6A one module switch, 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End(9 Module)

Supply and fixing of 1X80W LED street light fitting with LED (Higher End Philips/Havells) complete with 32mm dia GI pipe (Class ‘B’) with 1 No. 32mm GI bend complete on the existing post/wall with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads MS clamps and aluminum painting.

Supply and fixing of 200W LED energy saving highbay LED with PDC housing suitable forceiling (Surface) mounting with special type MS Angle with suitable necessary connection. (Philips/Havells/Equ) (For RMG Heating)

Supply and erection of G.I. Stepped tubular pole of 8 Metre Length Single Ornamental Bracket Pole with Base Plate (250 x 250 x 6mm) 114.30mm OD x 5.40mm Thick x 4500mm Length, 88.90mm OD x 4.85mm Thick x 1750mm Length, 76.10mm OD x 3.25mm Thick x 1750mm Length, with single arm ornamental bracket of outer dia 50 mm pipe bent suitably to give a height of 1.5 mtr and overhang welded suitably with ornamental bracket and fixed rigidly with 8 Nos of bolt and nuts to prevent any turning movement of bracket due to wind with sheet moulded compound (SMC) junction box IP 42 protection of size (295mm x 225 mm x 120mm) , fire proof of suitable size with 4 way terminal block with hylem sheet of size (250mm x 200mm x 6mm) with 1 No. 16 A fuse unit with 1 No. suitable links provided at a height of 2.0 mtr from the ground level with embossing of metalic "DANGER 440 V" with earth connection with earth bolts of size 8mmx25mm welded on the pole at one end with 4 mtr of 40 mm PVC pipe for incoming and outgoing cable. The pole shall be provided for coil earth with No. 8 for coil earth with No. 8 SWG GI wire of 11.5 mtr of length in which 10 mtrs of total length compressed in to a coil of one meter length. The pole shall be painted with one coat of red oxide primer paint and two coats of aluminium paint of reputed make to the length of pole with supply and fixing of 150W LED street ligh equivalent to be approved by PWD officials with necessary connection wire from junction box to the fittings with 3 x 1.5 sq mm PVC copper wire for each fitting with pole earthing with necessary connections testing and commissioning as per the specification. The pole should be mounted on the special type of bracket which would be fixed on the side of the crash barrier and the details are as follows The bracket should be fabricated like diagnal cut of the cubic structure with 25 mm thick plate of size

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq mm copper wire and making good of the concealed position.(SD-344)

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.(SD-535)

Supply and fixing of Three phase Seven Segment type 4 way 63A distribution board with Metal Door cover Code IP42 Protection , with 63A 4 pole MCB as incoming and Sub incomers 3 Nos 40A DP ELCB and 12 Nos 6-32A SPMCB as Outgoing on Wall with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Hager/legrand) (Lighting Purpose)(DATA–23)

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For Street Lights) (SD-667)

Supply and clarnping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.(For Street Light post clamping on post for 2 mtr each post)(SD-204)

Supply and fixing of the 4x16 sqmm brass cable gland for the 4x16 sqmm PVC Armoured LTUG cable with earth connection.

Renewal by Supply and fixing of 0.7mx Height 1Mt x Width 0.75mt floor mounting type Pillar Box made up of 16SWG CRCA sheet steel with one coat of primer and two coats of painting in suitable masonry pedestal and AI frame work with one no Danger board and earth connection and necessary identification of danger letter in BOLD and connecting with 4 Nos 2"x1/4" copper flat for RYBN for the outgoing loads with necessary Identifcation stcikers, safety danger board. (DATA -26)

Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height

Supply of 5KVA (Single Phase In & Single Phase Out ) microprocessor controlled double conversion true online ups system with builtin isolation transformer, auto phase sequence correction, power factor correction, builtin manual bypass arrangement with exide sealed maintenance free batteries for 2 hours backup time with suitable interlink cables and ms powder coated rack for batteries CONFIGURATION: True On line double conversion ups system with pulse width modulation (PWM) Technology using IGBT inverter. RECTIFIER: Full wave (shall fully meet the specified input power requirements ) INPUT: 3 phase 320V – 460V OUT PUT:230V +1% on battery mode FREQUENCY: 47HZ-53HZ SYSTEM DC VOLTAGE: 360V INVERSION TECHNOLOGY: Micro processor controlled, pulse width modulation with Instantaneous sine Wave control using IGBT. INVERTER OUT PUT : ( Out put Galvanic Isolation through Double winding Isolation Transformer at Output of Inverter shall be part of UPS Design ) LOAD POWER FACTOR: 0.8 to lag to unity REGULATION : for Balanced load + 1% For 100% unbalanced load + 2% FREQUENCY: 50Hz + 0.5% WAVE FORM : True sine wave TOTAL HARMONIC DISTORTION : Less than 5%

OVERLOAD CAPACITY: Inverse Time Characteristic 125% for 10 minutes 150% for 1 minutes EFFICIENCY : 1. Converter – 90% 2.Inverter - 85% 3. Overall – 80 % ( full load) OPERATING TEMPERATURE : 0 to 45 Degrees centigrade on full load CREAST FACTOR: 3 : 1 RELATIVE Humidity : : 95% at 35 Degree Centigrade non- Condensing CHARGER: Built in solid state automatic float- cum boost charger with constant current, constant voltage mode of charging along with current limiting features. Ripple in DC shall not exceed 2% when battery is disconnected. PROTECTION( in built) i) output under Voltage ii) output over Voltage iii) ) output over load iv) output short circuit. v) HRC fuses /output/ battery vi) Battery low trip vii) battery charges current limit.

Supply and Installation of 4 MP IP bullet/dome Camera with SD card support, Progressive-scan CMOS Sensor, Starlight Technology for Low-light Applications, Built-in Microphone. Make:NEOS/Eq.

Supply and Installation of 32 Channel NVR with 2 sata. Make:D-Link/Eq

Supply and Installation of 1 KVA UPS with 60 minutes power backup. Make:NEOS /Eq.

Supply and Installation of 24-port POE switch with Compact design for convenient placement. Make: D-link/Eq.

Supply and Installation of 8TB built in Hard Disc Drive. Make: Seagate/Eq.

Supply and Installation of 6U wall rack with 0.6 KVA UPS. Make : D-Link/Eq.

Supply and Installation of 65 inch 24 x 7 Signage display for CCTV monitor. Make :Sony/Eq.

Supply and Installation of Wireless mouse. make:Dell/Eq.

Supply and laying of CAT 6 unarmored cable in existing PVC pipe on wall and ceiling. Make:D-Link/Eq.

Supply and laying of 25mm dia PVC rigid pipe with PVC accessories on wall / ceiling/floor.

Supply and Installation of CCTV camera pole as per PWD standard. Make:K-Lite/Eq

Supply and Installation of outdoor 6 core OFC cable. Make:D-Link/Eq

Supply and Installation of Media converter. Make:D-Link/Eq

Supply and Installation of 43 inch 24 x 7 Signage display for monitor. Make :Sony/Eq.

Supply and Installation of RJ 45 with face plate and back box for LAN. Make:D-Link/Eq.

Supply and Installation of RJ 11 I/os with face plate and back box for Intercom. Make:D-Link/Eq.

Supply and Installation of 24 port 10/100/1000 Mbps layer -2 fully managed switch. Make: D-Link/Eq.

Supply and Installation of 24 port fully loaded patch panel. Make: D-Link/Eq.

Supply and Installation of 1m length patch cord. Make:D-Link/Eq.

Supply and Installation of 2m length patch cord. Make:D-Link/Eq.

Supply and Installation of 3 trunk+16 analog extension, expandable up to 96 & 112 IP port with 2 KVA UPS. Make:NEC/Eq.

Supply and Installation of 8 port analog extension card with port license. Make:NEC/Eq.

Supply and Installation of 100 pair MDF Box with Module and Krone. Make:D-Link/Eq.

Supply and Installation of 50 pair MDF Box with Module and Krone. Make:D-Link/Eq.

Supply and laying of 0.5mm 10 pair telephone cable in existing pvc pipe on wall and ceiling. Make:D-Link/Eq.

Supply and laying of 0.5mm 2 pair cable in existing pvc pipe on wall and ceiling. Make:D-Link/Eq.

Supply and Installation of caller ID telephone instrument. Make:Beetel/Eq.

Testing and Commissioning of CCTV,LAN and Intercom system including demo and training.

BLUELEAF PROJECTS PRIVATE LIMITED (BID ID -1522646)

M/s PST Engineering Construction (BID ID -1522848)