WBIW/EE-I/DCD/eNIT-15/26-27/1

Dismantling artificial stone flooring upto 50 mm.thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m. In ground floor including roof.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special section , power pressed from M.S Sheet and galvanized with zinc coating of 150 gms/sqm ( both side inclusive ) as per IS:227 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick flanges of 27 mm and 37 mm, at 1200 mm centre to centre , one flange fixed to the ceiling with dash fasteners 12.5 mm dia x50mm long with 6 mm dia bolts , other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G I channels 45x15x0.9 mm running at the spacing of 1200 mm center to center , to which ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm , at 450 mm center to centre , shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clips made out of 2.64 mm dia x230 mm long G.I wire at every junction , including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long , the perimeter of ceiling fixed to the wall / partion with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval , including fixing of Gypsum Board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c , including jointing and finishing to flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both side of joint and two coats primer suitable for board , all as per manufacture's specification and also including the cost of making openings for light fittings, grills, diffusers , cutouts made with frame of perimeter channels suitably fixed , all complete as per drawings, specifications and direction of the Engineer-in-Charge but excluding the cost of painting with : ( ISI Mark on Board)

Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,labour and all other incidental charges complete as per direction of Engineerin- Charge. (Note: This work should not be executed without specific permission of Superintending Engineer). ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5 mm thick)

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength > 1500 N

Supplying, fitting & fixing best quality digital printed Ceramic tiles in coloured decorative on walls and floors to match with the existing work & 4 nos. key stones (10mm) fixed with adhesive 4.5 mm thick at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. With polymerised adhesive and epoxy grout pointing including spacer - 2mm (When tiles are laid over existing hard ready surface) all complete as per direction of Engineer-in-charge.

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (Payment will be made on finished length of the work). In 10-12 Micron thickness Annodizing film. Coloured. 2- track sliding window. Bottom frame

Top and side frame.

Shutter for all track sliding window. Bottom & Top member.

Style side member.

Interlock member.