Repairs to 5 cusec x 15mtr head Horizontal split casing pumping unit-II along with allied mechanical works at LIS Dulmachak-I and Repairs to 6 cusec x 15 mtr head Horizontal split casing pump unit-III along with allied mechanical works at Lift irrig

Repairs to5 cusec x 15mtr head Horizontal split casing pumping unit-II along with allied mechanical works at LIS Dulmachak-I

Decoupling of 5 cusec x 15 meter head discharge pump unit no II from 50 hp motor and then dismantling the pump from the base frame. Carriage & shifting of dismantled pump on head load to roadside using manual labour and then to workshop by carriage vehicle. Repair to 5 cusec x 15 meter head discharge split casing pump of pumping unit no IIof Lift irrigation station, Dulmachak - I workshop by dismantling and extraction of all worn out/damaged parts i.e. pump shaft, impeller, bearings, sleeves, bush, check nuts, nuts & bolts, gland plate, gland studs. Properly cleaning the internal surface of pump casing. Providing and fitting of new pump shaft after turning to bearing size and threading at positions of check nuts. Repairs to impeller by filling cavities, cracks and finishing to original size. Providing and fitting 2 no’s of new bearing on driving and non-driving end of the pump, 2 no’s neck rings, 2 no’s shaft protection sleeves, 1 no’s check nuts, nuts & bolts, fabrication of 2 no’s new gland plate with providing and fitting of 2 no’s new gland studs on ends of pump. Repair to bearing housing on driving and non-driving end of pumping unit by providing and fitting of bush, turning and fitting of bush to make inner diameter of bearing housing suitable for fitment of bearing. Reassembling all parts of pump with proper greasing of bearings and providing and fitting of gasket sheet between upper and lower part of the pump. Providing and fitting of graphite packing of suitable size on both ends of pump. Shifting of repaired pumping unit on site and fitting of pumping unit on base frame. Alignment of the pumping unit. Repair to 250 mm diameter foot valve of pumping unit no II by way of dismantling parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. The job includes fabrication of strainer to stop entry of unwanted material and fitting it with foot valve. Repair to 200 mm dia sluice valve of unit no II, installed at Lift irrigation station Dulmachak - I, by way of cutting of nuts and bolts around the sluice valve with gas cutter. Completely dismantling all the internal parts of valve. Fabrication/Replacement of new stem rod with square threads. Providing and replacement of new wedge nut, repair to wedge shape disc with seat ring. Providing and replacement of new gland packing, gland plate with gland nuts. Properly checking inner body of sluice valve for any cavitations voids or corrosion repairing of the same. Complete assembling of valve with providing of graphite packing. Providing and fitting of rubber sheet between the flanges on both side of valve with providing of new nuts and bolts. Repair to 200 mm reflux valve dia by way of dismantling reflux valve from delivery side of unit no.II. The job involves extraction of broken flap of reflux valve. Providing and fitting of new flap with locking sheet. Replacement of hinge and hinge pin of the valve. Fitting of the valve on the delivery line with providing and fitting of new nuts and bolts along with rubber sheet. Repairs to 50 HP starter of pumping unit no- II by way of extracting the damaged worn out parts. Repair to Tripping system by brazing and finishing required size, Providing and fitting of no voltage coil, overload relay, moving and fixed contact point. Replacement of worn out thimbles nuts-bolts and internal leads duly soldered properly. Providing and filling of starter with 10 litres of fresh transformer oil. The job includes loading, un-loading, manual labour, carriage charges of vehicle (to & fro), tools & tackles, cost of materials, installation& testing charges at site. Complete job.

Rebate on Old Parts

Repairs to 6 cusec x 15 mtr head Horizontal split casing pump unit-III along with allied mechanical works at Lift irrigation station Jandi Nud.

Decoupling of 6 cusec x 15 meter head discharge pump unit no III from 50 hp motor and then dismantling the pump from the base frame. Carriage & shifting of dismantled pump on head load to roadside using manual labour and then to workshop by carriage vehicle. Repair to 6 cusec x 15 meter head discharge split casing pump of pumping unit no III of Lift irrigation station, Jandi Nud at workshop by dismantling and extraction of all worn out/damaged parts i.e. pump shaft, impeller, bearings, sleeves, bush, check nuts, nuts & bolts, gland plate, gland studs. Properly cleaning the internal surface of pump casing. Providing and fitting of new pump shaft after turning to bearing size and threading at positions of check nuts. Repairs to impeller by filing cavities, cracks and finishing to original size. Providing and fitting 2 no’s of new bearing’s no. 6309 on driving and non driving end of the pump, 2 no’s neck rings, 2 no’s shaft protection sleeves, 1 no’s check nuts, nuts & bolts, fabrication of 2 no’s new gland plate with providing and fitting of 2 no’s new gland studs on ends of pump. Repair to bearing housing on non driving end of pumping unit by providing and fitting of bush, turning and fitting of bush to make inner diameter of bearing housing suitable for fitment of bearing. Replacement of bearing housing of driving end of the pump with casting and fabrication of bearing housing as per the size of bearing and bolts on the outer size of pump. Turning and finishing as per the size. Reassembling all parts of pump with proper greasing of bearings and providing and fitting of gasket sheet between upper and lower part of the pump. Providing and fitting of graphite packing of suitable size on both ends of pump. Shifting of repaired pumping unit on site and fitting of pumping unit on base frame. Alignment of the pumping unit. Repair to 250 mm diameter foot valve of pumping unit no III by way of dismantling parts. Cleaning of all internal parts to remove silt and rust. Fabrication of new foot valve plate as per size, new leather washer, hinge pin, new nuts & bolts. The job includes fabrication of strainer to stop entry of unwanted material and fitting it with foot valve. Repair to 250 mm dia sluice valve of unit no III, installed at Lift irrigation station Jandi Nud, by way of cutting of nuts and bolts around the sluice valve with gas cutter. Completely dismantling all the internal parts of valve. Fabrication/Replacement of new stem rod with square threads. Providing and replacement of new wedge nut, repair to wedge shape disc with seat ring. Providing and replacement of new gland packing, gland plate with gland nuts. Properly checking inner body of sluice valve for any cavitation voids or corrosion repairing of the same. Complete assembling of valve with providing of graphite packing. Providing and fitting of rubber sheet between the flanges on both side of valve with providing of new nuts and bolts. Repair to 250 mm reflux valve dia by way of dismantling reflux valve from delivery side of unit no. 1II. The job involves extraction of broken flap of reflux valve. Providing and fitting of new flap with locking sheet. Replacement of hinge and hinge pin of the valve. Fitting of the valve on the delivery line with providing and fitting of new nuts and bolts along with rubber sheet. Repairs to 2 HP priming pump by way of complete dismantling internal parts of the pump. Replacement of shaft with new one, turning and finishing for bearing and impeller size. Providing and fitting of new bearings (2 no’s), new impeller as per sample, new motor fan , new coupling for connecting motor and pump, gland plate with studs. Extraction of damaged foot valve of priming pipe from the sump and. Providing and fitting of new foot valve. Assembling of priming pump with greasing of bearings. Testing of pump set on no load condition. Fitting of priming pump and suction pipeline at site. The job includes loading, un-loading, manual labour, carriage charges of vehicle (to &fro), tools & tackles, cost of materials, rebate on old parts, installation& testing charges at site. Complete job.

Rebate on Old Parts

Vaibhav Engineers and Technocrates

GEETA ENGINEERING MECH WORKS