PROVISION OF 2 STORE ROOMS NEAR BLDG No. 46 AT NAGZEERA LINES OF HQ JL WING, PROVISION OF STORE ROOM AT 115 INF BN TA, PROVISION OF TOILET CUM BATHROOM NEAR BLDG No. 01 RA LINE AT 373 (I) SUP PL ASC, SPECIAL REPAIRS TO BLDG No. 1-A-2 AT 373 (I) SUP P

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling timber scantling 40 Sq.cm and over in section in any position in un-framed work all as specified and directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed.

Taking down existing unserviceable eaves gutters rainwater pipes of any description and size including all fittings and making good disturbed surfaces all as specified and directed.

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets and frame work all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, ceilings, etc. including raking out joints, hacking for key scrubbing down with water etc. all as specified and directed.

Hacking out old broken glass (any thickness/ size, quality or description) from wooden frames, glazed with putty or fixed with beads all as specified and directed.

Cutting, chases for concealed water tubing and making good in CM 1:3 cutting not exceeding 10 cm girth in brick wall all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections all as specified and directed.

Taking up or down 20mm bore steel water tubing and connections all as specified and directed.

Dismantling and breaking up drain pipes (AC/ PVC/ CI pipes) of 100 mm internal dia jointed in cement mortar/ solvent cement and taking out of trenches/ from walls if required all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and as directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation over areas n. exc. 1.5 m depth and getting out in hard/ dense soil all as specified and directed.

Returning filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

M&L for Moorum/ red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and as directed.

M&L for loose filling with broken brick bat aggregates of gauge 80 to 150mm in soakage pits, soakage wells, etc. all as specified and as directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread ,levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete type D2 1:4:8 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, type B-0, using 12.5mm graded stone aggregate as in damp proof course t horizontal or vertical surfaces including use of necessary form work all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in coping, bed blocks including use of necessary form work all as specified and directed

M&L for plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in coping, bed blocks including use of necessary form work all as specified and directed

M&L plain cement concrete 1:2:4, type B-0, using 12.5mm graded stone aggregate as in haunching, benching in manholes including necessary form work all as specified and directed

M&L for extra for forming fair finished drain or channel of 25cm inner girth in cement concrete using extra cement including forms moulds mitred/ stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slabs, etc. set in CM 1:6 all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in columns, pillars, piers, posts and struts all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in beams, cantilevers, lintels, lintel bands all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves and the like all as specified and directed.

M&L for Reinforced cement concrete M25 design mix using 20mm graded stone aggregate in chajjas all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for Brickwork with sub-class `B’ bricks straight or curved on plan, to any radius in half brick thick walls built in cement mortar 1:4 all as specified and as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, lintel bands and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for use of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200m thick (Horizontal or sloping), flat rough finished surfaces of concrete all as specified and directed.

M&L for use of form work to sides and soffits of chajjas, flat rough finished surfaces of concrete all as specified and directed.

M&L for use of form work to edges of concrete flats, treads, bands and similar works, for rough finished concrete surfaces, horizontal or sloping, exceeding 10cm but not exceeding 20cm wide all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, rails, posts, rafters, purlins, etc. square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

Fixing only serviceable timber fillets, rails, posts, rafters, purlins, etc. square, rectangular or triangular in section, secured with nails or beads; sectional area exc 13 and n.exc 25 Sq.cm all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ ventilator shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

S&F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles exc 200 cu. Cm but n exc 500 cu. cm each all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels/ wire mesh shall be measured and paid separately.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F 150mm size mild steel barrel tower bolts, stove enamelled black with right bolt all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F 150 mm long mild steel pressed handles, oval type, stove enamelled black all as specified and as directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as secified and as directed.

S&F 300mm long mild steel helical door spring, ordinary rat tail pattern spring, including roller and roller plate complete all as specified and as directed.

M&L for floor door stopper of brass body and tongue, anodised, with 140mm long cover plate and hard drawn steel spring, fixed in floor all as specified and directed.

S&F Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of weight between 61 to 80kg, all as specified and directed. Make : EVERITE/ ALLWYN

S&F 100mm size mortise lock, brass, vertical type, four levers, all as specified and directed. Make: Godrej or equivalent.

S&F Harrison rails, anodised aluminium alloy, with fixing brackets, stops, rollers etc. all as specified and as directed.

S&F brass knobs, 40mm dia fixed with nut and screw and washer all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 76 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for mild steel hold fast and similar small article conforming to Fe-290 Grade-E-165 all as specified and as directed.

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates complete conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel tower bolt, hold fasts, complete with glazing bars, dovetailed or welded all as specified and as directed.

All as described in item No. 81 but withot glazing bars

S&F Steel ventilators with top hung shutters including hinges with steel peg stays, hold fasts, complete all as specified and as directed.

M&L for mild steel framed work as in gates of angle or other section with gusset plate, rails, braces etc complete, prepared for hanging or sliding with and including either hook or hinges and hanging fastening and fixing complete conforming to Fe 410W (Gde E-250) all as specified and directed.

M&L for 1.6mm thick mild steel plain black sheet covering to door shutters, covering to door chowkats (frames), etc. cut to size edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required all as specified and directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

S&F mild steel framed work such as ornamental and intricate design gates, grills conforming to Fe-290 Gde- E-165 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F in repairs 0.8mm thick galvanised plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as specified and as directed.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Cleaning the top surface of RCC slab and brushing with neat cement slurry @ 3Kg/Sqm and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.4 litre per Sqm & providing 4mm thick APP modified water proofing membrane weight not less than 4.5kg/ sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including minimum 10cm side/ over laps & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying applying a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

M&L for designer concrete roofing tiles, red colour, 420 x 330mm size, 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry all as specified and as directed. Make: ETERNA model of INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete ridge/ hip cap tiles to suit designer red colour concrete roofing tiles, 330 x 207/249mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete hip starter tiles to suit designer red colour concrete roofing tiles, 360 x 210mm size, minimum 17mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete 3 way cap tiles to suit designer red colour concrete roofing tiles, 351 x 429mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

S&F PVC (SWR) eaves gutter half rounded 150mm bore including pipe accessories PVC holder bats bolts nuts etc. all as specified and directed.

M&L for 3mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41), weight not less than 7.6 kg per sqm, complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions, fixed in repairs, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing shown on MES SSR Part-I

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminium anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling all as specified and directed.

S&F suspended false ceiling system with 16mm thick mineral fibre acoustical MINA TUFF EDGE TILES (MIRO LOCK), performance class - I (BS 456, Part 6&7) with bio coating on the exposed face of tiles, module size 60mm x 600mm, laid on 15mm thick SILHOUTTE EXPOSED GRID system, with medium load carrying capacity of 11.68 kg/ sqm, white/ black colour, all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified and directed.

M&L for coloured non skid ceramic tiles, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured joint free ceramic tiles, edge cut, 9 to 10mm thick area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, in floors, skirtings, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 450mm x 300mm x 7mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for coloured, polished, designer cement concrete tiles 25cm x 25cm x 25mm thick, machine pressed, set, jointed and pointed in neat cement slurry, as in pathways, pavings, etc., laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 80mm thick coloured machine pressed precast cement concrete interlocking paver blocks, M-40 grade, any shape and size with anti skid finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for approved dry river sand filled under foundation/ floors/ pavements including watering and consolidation all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete ceiling surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound, on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on stone masonry surfaces or other than fair faces of brick work, finished even and smooth without using extra cement all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 5mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beadings in square not exc 0.5 sqm in each pane all as specified and directed.

M&L for 5mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beadings in square exc 0.5 sqm in each pane all as specified and directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty/ neoprene beadings in square n exc 0.5 sqm in each pane all as specified and directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer over 1mm thick layer of wall care putty on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, over a coat of alkali resistant primer on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior emulsion paint over a coat of primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces of any description n exc 10 cm width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 500 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position and testing complete all as specified and directed.

S&F 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

S&F 25mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 25 mm bore UPVC water supply pipes, 10kgf/ sqcm, including all fittings such as elbow, reducer, tee, couplers, short pieces, connectors etc. fixed to walls , ceilings with PVC batten holders all as specified and as directed.

S&F 15 mm bore Bib tap, long body, brass chromium plated, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. 563 of JAQUAR or equivalent model in ARK/ JOHNSON/ ESS ESS

S&F 15mm bore stop valves, brass chromium plated, fancy type, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F 15mm bore stop valves, cast copper alloy, screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F 15mm bore brass CP angle valves, high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore PTMT angle valves, high pressure, (Minimum weight-90gms) screwed both ends for iron pipe for unions all as specified and as directed.

S&F pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F in repairs pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F vitreous china wash basin, white, size 550x400mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F in repairs vitreous china wash basin, white, size 550x400mm, including provision of waste pipe and fittings, CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F Vitreous China urinal, bowl type (back or corner wall type), white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F Vitreous China urinal, half stall type, white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap including provision of lime concrete bedding etc complete all as specified and directed.

S&F syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, 600mm long all as specified and directed.

S&F brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F brass chromium plated shower rose swivel type 125mm size suitable for fixing with 15mm bore pipe all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), suitable for urinals all as specified and directed.

S&F in repairs glass shelf assembly, 5mm thick, 6" wide , fixed to wall with suitable brackets, bolts, nuts, screws etc. complete all as specified and directed.

S&F in repairs liquid soap container, stainless steel body, fixed to wall with CP screws and wooden/ plastic cleats all as specified and as directed.

S&F 110mm bore UPVC (SWR) pipes single socketed in any length with solvent cement joints laid in floors/ trenches all as specified and directed.

S&F 75mm bore UPVC (SWR) pipes single socketed in any length with solvent cement joints laid in floors/ trenches all as specified and directed.

S&F 110mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F 110mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F 75mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M&L for 150mm bore Salt glazed stoneware drain pipes, laid in trenches and jointed as specified all as specified and directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, holders, light fittings, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping/ PVC conduits of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module GI box flush mounted with wall with modular cover plate & frames for mounting switches/ sockets etc. for one light point controlled by one modular switch 1 way complete all as specified and directed.

All as described in item No. 177 but for one ceiling fan/ exhaust fan point controlled by one switch/ regulator.

All as described in item No. 177 but for one call bell point controlled by one bell push

All as described in item No. 177 but for one 05/06 Amps socket outlet on independent board.

All as described in item No. 177 but for one 05/06 Amps socket outlet on the same board with other switches.

All as described in item No. 177 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15/16 Amps power socket point on independent board all as specified and directed.

All as described in item No. 177 but wiring with 4 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 4 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15/16 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular bell push, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F fan regulator electronic modular step type, 2 module, suitable for 1200mm sweep ceiling fan all as specified and directed.

S&F in repairs call bell, ding dong, 230 volts AC supply all as specified and directed.

S&F in repairs, epoxy powder coated MCB DB TPN 4 Way, 415 volts 200 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs MCB DB SPN 12 Way, 240 volts with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DB SPN 8 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs MCB DB SPN 4 Way, 240 volts with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB TPN 63A 10KA 'C' series 50Hz 415 Volts AC supply all as specified and as directed.

S&F MCB DP 63A 10KA 'C' series 50Hz 2405 Volts AC supply all as specified and as directed.

S&F MCB DP 40A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB SPN 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED tube, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED tube, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan 230 Volts, Single Phase, star rating, 1200 mm sweep, energy saving, including provision of suitable size down rod made out of medium grade mild steel tube fixed with necessary clamps, bolts, nuts, washers, etc., provision of suitable size flexible copper conductor from connector to terminal, mild steel fan hook completeall as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in makes CG/ ORIENT

M&L for 50mm bore GI tubes, medium grade, as in supports for hanging of ceiling fans of 1200mm/ 1400mm sweep, cut to required length, grouted into wall and making good disturbed surfaces as required all as specified and as directed.

S&F exhaust fan, 300mm sweep, 230/240 Volts, 900 RPM, heavy duty, single phase, metallic body with louvres and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells Turbo Force SP model or equivalent model in Almonard/ Crompton Greaves

S&F exhaust fan, 300mm sweep, 230/240 Volts, 1350 RPM, single phase, metallic finish powder coated, with wire grid protection and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing including provision of 12mm thick plywood of suitable size with necessary circular hole for fixing of exhaust fan and fixing the plywood to existing windows with necessary bolts/ clamps, etc. all as specified as directed. Make: Havells VENTL-AIR DSP model or equivalent model in Almonard/ Crompton Greaves

M&L for approved riddled earth, spread dry in trenches as in cable cushioning at bottom and top including punning down all as specified and as directed. Note :- Punned thickness will be considered for payment.

M&L for burnt bricks, old size, sub class 'B' of designation 75, laid in trenches as in protection for UG cables all as specified and as directed.

M&L for GI tubes, light grade, 40mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 16Sqmm x 4 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete all as specified and as directed. Note: Excavation, earth work, sand cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

All as described in item No. 213 but 10sqmm x 4 core

All as described in item No. 213 but 25sqmm x 4 core

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s. KIRAN M CHOUGULE

SHRI.H.R.PATIL

M/s B C CHOUGULE