AS-16-138 Balance work of Construction of road from Padmajhar to Andherighat Jayantipur Road

Amount

Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under custody of the contractor till taken over by the Department.) scarfing and joining piles 25cm to 30cm dia dressed to heartwood 90cm. In length including supplying, fitting and fixing with 2 nos. of 50mm x 10 mm MS FI clamps and 16mm dia MS bolts and nuts etc. complete as directed (Refer to quantity estimation)

Earth work in excavation of foundation of structures as per drawings & technical specifications, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material. I. ordinary soil A. manual means (a) without dewatering (ii) up to 3m depth

Bored cast-in-situ M35 grade R.C.C. pile excluding reinforcement complete as per drawing and technical specification and removal of excavated earth with all lifts and lead upto 1000m.(Pile diameter-1000mm) (N) without plasticiser

Levelling course for pile cap

Pile load test on single vertical pile in accordance with IS:2911(Part-IV). a). Initial and Routine load test.

Cement concrete for reinforced concrete in pile cap complete as per drawing and Technical Specification. Including steel shuttering formwork (N) without plasticiser A. RCC grade M25 (i) Using Concrete Mixer

Supplying, fitting and placing un-coated TMT bar reinforcement in foundation complete as per drawing and technical specification (b) with TATA make TMT rebar.

Plain/Reinforced Cement concrete, in Substructure complete as per Drawing and Technical Specifications and steel shuttering formwork. (N) without plasticiser E. RCC Grade M 25 1.Height up to 5.0 m Case – I : Using Concrete Mixer

Supplying, fitting and placing TMT bar reinforcement complete in substructure complete as per drawing and technical specification (b) with TATA make TMT rebar.

Back filling behind End wall of abutment,wing wall & return wall complete as per Drawing and Technical Specification (B) Sandy materials

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification.

Supplying, fitting and fixing in position true to line and level elastomeric bearing conforming to IRC:83 (part-II) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and Technical specifications.

Furnishing and placing reinforced / Prestressed cement concrete in superstructure as per drawing and Technical Specifications. Including steel shuttering formwork. (N) Without plasticiser B. RCC Grade M 25 Case - I : Using Concrete Mixer ii) For T-beam and slab (a) Height upto 5m

Supplying, fitting and placing TMT bar reinforcement in superstructure including splicing complete as per drawing and technical specifications (b) with TATA make TMT rebar.

Providing and laying cement concrete wearing coat M 30 grade including reinforcement complete as per drawing and Technical Specifications

Construction of pre cast RCC railing of M30 Grade in situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500 center to center spacing between vertical post not to exceed 2000 mm leaving adequat space between vertical post for expansion, complete as per approved drawings and technical specifications.

Providing and and laying of a strip seal expansion joint catering to maximum horizontal movement upto 70mm, complete as per approved drawings and standard specificatons to be installed by the manufacturer / supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation.

Drainage spouts complete as per approved drawings and technical specifications.

Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701

Providing and laying pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and technical specifications A. Stone/Boulder

Providing and laying filter material underneath pitching in slopes as per drawing and technical specifications.

Providing and laying boulders on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification .without wire crate

Sub way-Construction of embankment with material obtained from borrow pits,Construction of embankment with approved materials obtained from borrow pits with a lift up to 1.5m, transporating to site, spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead up to 1000m as per technical specifications clause 301.5(a) Private land

Gravel/Soil-Aggregate Base (Table 400.2) Grading B Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402

Construction of cold weather Bamboo bridge overall width of 3.70m and clear road way 3m with jungle wood post 20cm to 25cm dia 5nos. In each rows and rows being 2.1m. apart except for the navigable span which should be 3m. Post to be driven at least 180cm. or more below ground level including providing 20cm to 25cm center to center and placed over 20 cm dia, jungle wood dham, 15cm dia. jungle wood bracing collar fixed by bolts and nuts, straps etc. mature bholuka Bamboo cross groth all closely packed and tied 75cm wide track way made from 38mm thick 1st class local plank fixed on 75mmx100mm first class local wood battens 120cm apart and 3 lines of jati bamboo horizantal railing fixed in bholuka bamboo post placed at 210cm apart and white washed including all necessary nuts and bolts, coir ropes, struts, nails etc. complete with a layer of brushwood to exposed portion out-side trackway with earth topping complete as per direction of the department.

Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. i) By Manual Means A) In area of non-thorny jungle

Removing all types of Hume pipes and stacking within a lead of 1000 m including earthwork and dismantling of masonry works as per Technical specification Clause 202. Rate as per SOR Rural roads - 2016-17(A) Upto 600 mm dia Hume Pipe

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of brick masonry including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 metres as per technical specification clause 202

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material,disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 metres as per technical specification clause 202 I. By Manual Means (C) Reinforced Cement Concete B. Cement concrete

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (i) Private Land

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (i) Private Land

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (A) By Mix in Place Method ii) For Grading II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. 2) Grading -II (A) By Manual Means

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. 3) Grading –III (A) By Manual Means.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base /WBM/WMM including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502. (i) Low Porosity

(iii)Providing and applying tack coat with Bitumen emulsion (CRS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

20 mm thick Open Graded Premix Carpet using Bitumen Emulsion as per Technical Specification Clause 508.2 (using concrete mixture of 0.4/0.28 cum capacity & with CMS) Providing, laying and rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a tree wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.2 Rate as per F-8

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels grade and cross fall using TypeA,Type B and Type C as per Technical specification clause 510. With cold mix Binder (As per IRC:SP:100-2014) and through credible tecjnology partners duly licensed by CRRI. By Manual Means Case III:Type-C (9.5mm to 2.36mm) Bitumen Emulsion (RS-2)

Kilometer Stone Reinforced cement concrete M 15 grade kilometer stone / local stone of standard design as per IRC: fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. ii) Ordinary Kilometer Stone (Precast)

Kilometer Stone Reinforced cement concrete M 15 grade kilometer stone / local stone of standard design as per IRC: fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. iii) 200 m stone (precast)

Providing & fixing retro – reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification Clause 801 ii) 60 cm equilateral triangle

Providing & fixing retro – reflectorised cautionary, mandatory and informatory sign as per IRC:67 made encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm 6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification Clause 801 vi) 60 cm x 60 cm squareLogo board at starting point

Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701Citizenship Informatory Board (Area=1.35 sqm * Nos.=1)

Maintenance of Culverts I) Maintenance of Hume pipe Culvert by way of Clearing, Cleaning, Erosion repair, repairs to cracks, parapet wall and protection work as per drawing and technical specification Clause 1908

Construction of RCC guide posts of 250 mm dia M15 grade cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC posts not to exceed 1 in 500 as per drawing and technical specification Clause 1608.2

Printing New Letters and Figures of any Shade Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and Technical Specification Clause 1701(ii) English and Roman

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Bedding for pipe (ii) Type B(First Class) Bedding Laying (First Class) bedding on well compacted sand moorum as per Clause 1105(ii) (i) Sand Filling

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. II. In 1:4 cement mortar in 1:6 Cement mortar

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia

Routine Maintenance for 1st Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 2nd Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 3 rd Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 4th Year (The Bidder has to quote the exact amount as mentioned in estimated rate)

Routine Maintenance for 5th Year (The Bidder has to quote the exact amount as mentioned in estimated rate)