REPAIR MAINT TO CHAJJA ROOF TREATMENT INTERNAL WATER SUPPLY PLUMBING WORK PAINTING FIRING RANGE AREA BRICK WORK COMPOUND WALL PCC COPING BARBED WIRE FENCING AND CERTAIN MISC B R WORKS

Amount

M&L Repair to ends of chajjas/ parapets by removing old concrete, loose material & cleaning of the reinforcement and finishing the surface with rich cement mortar 1:3 , finished fair & even and making good with existing finishes complete all as specified and as directed. Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding.

Repair to cracks and damaged existing surface of RCC roof slab/RCC facia/RCC chajja upto double storey (Approx height 7.50 Mtr from the natural ground level) by structural strengthing using injection pressure grouting with Sikadur 52, low viscous epoxy grout of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals & M/s Thermex (as approved by GE), complete all as manufacturers and all as specified and directed by GE.

Providing and drilling 10mm dia holes using pneumatic drill as per site condition but not exceeding 50cm c/c in zig-zag patten for 75mm depth and fixing high pressure bear up Metal/Aluminium body indection packer along the holes and packing with Sika rep Micro Crete 4, rapid setting cement based plugging mortar of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals & M/s Thermex (as approved by GE)

Mixing base and hardner of Sikadur 52, low viscous solvent free epoxy injection grout of Make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals & M/s Thermex (as approved by GE) using slow speed electricity operated mixing paddle (200-300RPM) and injecting the same using electrically operated high pressure (upto 1000 Kgf/SqCM) pump until refusal to adjacent complete as per manufacturers specification.

Cutting and flushing the nozzoles and excess materials with a sharp scraper to take away sharp protrusions and to get a smooth and flat finish

M&L for Dismantling/ taking down old existing unserviceable cement plaster, loose/ unsound weaken cement concrete of any description and in any position from existing external / internal surface of RCC roof/ slab/ beams/ columns/ RCC facia for an average depth of 25mm (Approx height 7.5m from natural ground level) with power driven pneumatic flat/pointed chisel and removing the honeycombed area including all the corners and making a neat profile of the cavities, roughen the smooth surface , scrapping out/removing corrosion all loose/scale/rust etc form the visible reinforcement by applying rust remover such as Rust Off 100 of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermax Limited( as approved by GE) and cleaning the steel reinforcement properly, complete all as per manufactures instruction and all as specified and directed by Engineer-in-Charge.allowed to dry.

Note :- (a) Providing cement based angle fillet for 75mm X 75mm admixer with Sikacim, integral waterproofing liquid M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex Ltd, (as approved by GE) @ 0.2% by weight of cement or as per manufacturer’s instructions over a coat of acrylic emulsion bonding agent, such as Sika Latex in 1:1:3 ratio of Make M/s Sika India Pvt Ltd, or equivalent in M/S Fosroc chemicals, M/s Thermex Ltd (as approved by GE) having specific gravity of 1.02 or as per manufacturer’s instructions with necessary surface preparation such as creating mechanical key like rougheing the surface by scrabbing, grit blasting and cleaning the existing surface using high pressure water jet machine having pressure upto 500 bar pressure to remove the dirt, dust, loose particles , wax, efforencene and other contaminations from the surface of RCC columns/ beams/ slabs/ facia/ any brick/ stone surfaces etc complete all as manufactures instructions and all as specified and directed by Engineer-in-Charge.

(b) Providing and applying FRIAZINC R, corrosion inhabiliting Active Zinc rich primer of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex Ltd (as approved by GE) along the exposed reinforcement surface property and allowed to dry.

c)Providing and applying Hibond, Epoxy based Thixotropic bonding adhesive of Make from M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex Ltd, (as approved by GE) over the prepared concrete surface to get a good bonding between existing concrete surface and providing Sika Rep Microcrete 4 Fiber reinforced cementitious repair micro concrete of make M/s Sika India Pvt Ltd, or equivalent in M/s Fosroc Chemicals, M/s Thermex Ltd ( as approved by GE) over Epoxy based bonding agent applied area before 6 Hrs etc including providing necessary proportions , bracing and runners to relieve the member from the load coming on it including scaffolding leak proof shuttering with working platform as required and as per design and pattern complete including preparing the surface to match with the existing surface,complete all as specified and directed.

(d) Note : The work under (Item No. 2 to Item No. 9 of BOQ) shall be carried out through authorized and qualified applicators from any of the following manufacturer only. M/s Sika India Pvt Ltd, M/s Fosroc Chemicals, M/s Thermax Limited

(e) A performance guarantee certificate for two years shall be submitted by the contractor to the GE on completion of work as specified

(f) The unit rate quoted is deemed to be included for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land. Note: Periodicity of cutting of grass shall be before commencement of work and after completion of repairs.

Taking down chowkhat or frame (wooden/steel) exceeding 1.50 Sqm and not exceeding 4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

Taking down shutters of any description exc 1.0 Sqm and n.exc 2.0 Sqm each complete all as specified and directed.

M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F Factory made 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

S&F 250mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Petty repair to easing of wooden window, wooden ventilator, cupboard door, wardrobe door, PVC door, window shutters, kitchen cupboard shutters, show case shutter drawers including fixing of screws adjusting handles, knobs tightening piano hinges including misc small adjustments , (size upto 3 Sqm). minor repair and easying and adjustment/alignment to openable with accessories and including taking down and refixing complete all as directed.

Taking down chowkhat or frame(wooden/steel) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F in Steel windows with side hung shutters including projecting type hinges, frame with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing complete in square n exc 0.50sqm in each pane complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and directed.

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed.

S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm in each pane complete all as specified and directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass exc 0.5 sqm in each pane complete all as specified and directed.

Petty repair to door shutters for easy closing/opening (size upto 3 Sqm) including minor repair and easing, adjustment/alignment to openable with assessories and including taking down and refixing, tightening of hinges or changing the position of hinges,welding of hinges door to frame adjustment of tower bolts, sliding bolts with new screws etc, complete all as specified and directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 150 mm long complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed.

M&L 20mm dia mild steel powder coated drapery rod cut to length required without joint in between and including mild steel powder coated fancy type brackets and fixed at openings including taking down existing one complete all as specified and directed.

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

S&F Magnetic catches with 8mm dia steel ball and brass body and striking plate including taking down existing one complete all as specified and directed.

S & F in repair 18/19 mm thick ,water proof plywood , fixed to Cupboard work in any position with nails including removal of old boards of any description complete all as specified and as directed.

Supply and fixing Anodized aluminium size 605 x 605 mm snap grid frame work for false ceiling as per manufacturer instructions, with hangers of GI wire of suitable dia (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and 6mm thick Non asbestos fibre cement building boards, fixed to sheet suitably placed in false ceiling grid made of Aluminium/G.I./ M.S.as per specification and drawing and including dismantling old unservicable ceiling board including frame of any type and description, complete all as specified and directed.

Removing plant/Uprooting of vegetation growth including roots on wall/roof/parapet near pipes etc and applying acid treatment after removing roots for preventing regrowth and making good disturbed surfaces/area in superficial area exc 150sq.cm but n.exc 400 sq.cm and averaging depth not exceeding 10 cm by using PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) or 10mm thick plastering in cement mortar 1:3 as required and finishing the surfaces to match with the existing surface complete all as specified and directed.

Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside MOD land. NOTE :- Unit rate quoted shall also include for removal of PVC water storage tank and water pipe lines wherever existing carefully and refixing at the same or other position after completion of roof repair work

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with waters to remove dusts etc. complete all as specified and directed.

M&L for Brushing neat cement slurry with 3kg/sqm all as specified and directed.

M&L PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed.

M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with liquid WPC as per manufacturer instructions, complete all as specified and directed NOTE :- Integral WPC shall be measured and paid separately.

Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface complete all as specified and as directed.

M&L APP polymeric membrane min weight 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaces by torch application method complete all as specified and directed.

M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces complete all as specified and directed.

M&L in repair torching of existing APP membrane by torching incl primer etc all as specified and directed

M&L for cement plaster rendering 15mm thick on fair faces of brick/concrete surfaces with two coats i.e. (10mm thick backing coat in CM 1:6 and 5mm thick finishing coat in CM 1:4) and mixed with liquid water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement (WPC to be measured and paid separately) and Taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L for cement plaster rendering 10mm thick in CM 1:6 on fair faces of brickwork or concrete surface as on wall finished even and smooth with thin layer and taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces with smooth finish of any description, complete all as specified and as directed.

M & L for preparation of new plastered surfaces of walls applying plaster of paris putty one coat over plastered surface to prepare the surface even and smooth finish and applying two finishing coat of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat oil bound distemper complete all as specified and as directed.

Material and labour for Preparation of old plastered or unplastered surface of ceiling, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of old decorated surfaces of walls/ceiling by using pressure washer, remove all dirt & dust ,applying one coat of wall care putty and then applying two coats of premium oil bound distemper over one coat of primer as per manufauture instruction of required shade complete all as specified and directed.

M&L for Preparation of old painted wooden surface of any description and applying one coat of synthetic enamel paint not otherwise described over 10 cm width or girth, complete all as specified and directed.

M&L for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint over 10 cm width or girth, not other wise described complete all as specified and as directed.

Petty repair to renewing/matching glazed or ceramic coloured tiles in floors/walls in patches area not exceeding 5.00 Sqm including dismantling, removing and cleaning old tiles preparing beds and laying screed bed in CM 1:4 setting, jointing and pointing new or old tiles and joints filling and apply white cement and complete all as specified and directed

Taking down existing manually/machine operated steel rolling shutters area not exc 30Sqm each and erecting in same position, after easening, applying of greasing of all parts in rolling shutters uncluding changing of anchor rod, springs, steel rolling strips, locking plate, ball bearings. locks and vertical channels all as directed. Spare parts shall be measured and paid separately, after replacement of following unserviceable parts as required for smooth functioning of rolling shutter and refixing properly including bracket complete all as specified and directed.

S & F in repairs Steel rolling shutters, in any size and any position with ball bearing, as specified including top cover, anchoring rod, shaft, lath patty,crank wheel, side cover, hood cover, locking plate, hasp and staple and one shop coat of primer,2 coat of aluminium paint; erected in position as indicated, complete manual or gear operated type. Thickness of laths 1.25mm complete all as specified and directed.

Supply and fix polished Sadarahalli granite slab flooring 20 to 22 mm thick with grey cement slurry mixed with pigment to match the shade of the slab including 20mm thick screed bed in cement mortar 1:4 complete on staicase complete all as specified and as directed.

Supply and fixing in repairs 7 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit. Make Easydry or equivalent.

M&L Repair to leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ washbasin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe embeded in floor in bathroom or kitchen making good to the damaged portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed

M&L Repair to leakage/seepage from the wall/ door bend /door tee/ 'Y' junction/ 'T' Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damaged soil waste pipes or fittings of any shape, specification and size, making good to the damaged portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and finished the surfaces matching to existing wall to avoid the leakage/ seepage at the site of work complete all as specified and directed.

Note for item No 71 & 72 :- (a) Find out main cause of leakage and take necessary steps to resolve / rectify. (b) Replace existing tiles in case leakage through NT/FT. (c) The rate also include provision of new NT/FT. (d) The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as directed by the manufacturer's specification. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit

M&L for Treatment of the sunken floor slab comprises of the following specification and all as specified and directed. Make :- Dr Fixit/ M/s Sika india Pvt Ltd/ STP Ltd/ M/s Fosroc Chemicals

(a) Demolition of cement concrete filling of any description in sunken portion in toilet and removing debris outside MD land.

(b) Cleaning the sunken/ lowered portion of RCC slab surfaces (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding conc to achieve proper slope including cutting holes in bricks or RCC wall for spout (WPC shall be measured and paid separately)

(c) Rendering of uneven surfaces with 10mm thick in CM 1:4 mixed with integral water proofing as per manufacturer instruction. Fill it with water and check dampness and seepage. Where dampness/ seepage is noticed, nozzles shall be fixed and grouting carried out. (WPC shall be measured and paid separately).

(d) All junctions points of side wall spout where CI/ GI pipes are passing through shall be sealed with epoxy putty.

(e) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.

(f) Material and labour for applying two coats of polymer modified cementious water proof coating as per manufactures instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed.

(g) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound as per manufacturers specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately).

(h) Material and labour for PCC 1:5:10 type E2, n exc 150mm thick complete all as specified

(j) Material and labour for PCC 1:2:4 type B0 12.5mm thick aggregate, 50mm thick complete all as specified

Note for item No 74 to 83 :- Test the water proof area (ponding test) by filling water for at least 72 hours and tested for leakage, seepage to the entire satisfaction of GE.

Test shall be done in presence of Engineer-in-Charge.

Supply Only integral water proofing compound complete all as specified and as directed. Make:-Dr. Fixit Pidi Proof and equivalent.

Note for item No 88 :- The work shall be carried out by authorised and qualified applicators of the above mentioned manufacturer.

S & F in repair vitreous china squatting pan 'Orissa pattern ' size 580 x 440mm white with integral foot rests incl connecting to 'P' or 'S' trap and to flush pipe anti syphonage pipe etc complete including provn of lime concerte bedding and making good to floor complete all as specified and as directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches bore of pipe 75 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches bore of pipe 110 mm with PVC clamps and saddles including taking down old existing pipes and dismantling of cast iron/RCC/PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings complete all as specified and as directed

S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 75 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) bends of any radius with access door bore of pipe 110 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 75 mm complete all as specified and as directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal with access door bore of pipe 110 mm complete all as specified and as directed.

S & F in repairs 125/ 110 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 75mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off from premises & M&L for ceramic coloured tiles of size 350mmx250mm/ 300mm X 450mmx7 to 8 mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured / white cement to match the tiles inc rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces as in backing coat to receive wall tiles etc complete all as specified and directed.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off from premises & M&L for joint free non skid coloured ceramic tiles 7 to 8 mm thick area of each tile not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15 mm thick screed bed in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

Petty repair to internal/external water inlet water pipe line coming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removing the blockage including concealed water tubing etc of any height using scaffolding and making the water supply functional complete all as specified and directed.

Supply and fixing 15mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed.

Supply and fixing 20 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing complete all as specified and directed.

Supply and fixing 40 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down old steel tubing and connection complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank of 500 Ltrs capacity cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down old unserviceable tank complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm including taking down existing one complete all as specified and directed.

M&L Petty repairs to leaking water in bib taps, pillar cock, stop cock, angle valve, concealed stop valve, bottle trap of any description by changing the PVC washers/ Sheet washers,spindle brass,jumper brass or any other minor accessories (incl taking down and refixing) complete all as specified and directed

S & F in repairs Bib taps cast copper alloy chromium plated fancy type screwed down screwed for iron pipe or for brass ferrule and fixed for 15 mm bore complete all as specified and as directed.

S & F in repairs pillar tap with capstan heads chromium plated fancy type screwed down high pressure with or without letter 'Hot' or 'Cold' with long screwed shanks and flynuts screwed for galvanised iron pipe and fixed complete for 15 mm bore complete all as specified and as directed.

S&F in repairs of Stop Valve standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and as directed.

S&F in repairs of pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-110gms) complete all as specified and as directed.

S & F in repair bib tap standard of PTMT any colour screwed for iron pipe and fixed,15 mm bore (minimum weight 90gms) complete all as specified and as directed.

S&F in repairs of Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms) complete all as specified and as directed.

S & F in repairs 15 mm dia stop valves of cast copper alloy fancy type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and as directed.

S & F in repairs vitreous china wash down water closet (Pedestral pattern) EWC white incl plastic water closet seat cover and mild steel chromium plated or aluminium hinging device and connecting to 'P' or 'S' trap incl connecting flush pipe with flushing rim complete all as specified and as directed.

Supply and fixing in repairs plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed.

S&F in repairs grating doom 125mm dia with waste hole of Chromium plated (Min wt 40 gms) complete all as specified and as directed.

S&F in repairs Wash basin vitreous china (flat back or angle back type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe, complete all as specified and directed.

Taking down & re fixing high or low level flushing cistren 10 ltrs capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, replacement of including rubber washers, syphon set, float valve, handle,fixing to wall clamp/bracket, stopping of leakage etc wherever required complete all as specified and as directed

S & F in repairs PVC low level flushing cistern 10 Lit capacity including necessary brackets incl connecting flush pipe etc and making good the disturbed surfaces complete all as specified and as directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed.

S&F in repairs Vitreous China, half stall Urinal (back or corner wall type), complete including providing and fixing plugs, Urinal spreader, CP push cock, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and as directed

S&F CP Concealed stop cock, Regular body with adjustable wall flange screwed down screwed for iron pipe 15mm bore. including taking down existing one complete all as specified and as directed.

S & F in repairs PVC connection pipe 15 mm dia, 600 mm long with check nut and bolt with washer complete all as specified and as directed.

S&F in repairs 40mm bore unplasticised PVC pipe of pressure rating 10 kgf/Sqcm fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

S&F in repairs of Swivel Shower with arm of PTMT any colour and 195mm long bend of 45 degree with flange for fixed with 15mm pipe(Minimum weight15mm-90gms) complete all as specified and as directed.

S & F in repair Toilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screws and complete all as specified and as directed.

S&F Wash hand basin table counter type 560x400x200mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block, including long shank pillar tap, Brass chromium plated waste coupling 32mm bore, Waste pipe bottle trap, complete all as specified and as directed.

S&F PVC body cabinet box mirror of size 350mm X 450mm X 100mm of PTMT alloy of approved pattern and design including taking down existing one complete all as specified and directed.

S&F 300mm arc size, 5mm thick corner glass shelf with stainless steel brackets, stainless steel railing in bathroom and fixed to wall with brackets including removing the existing fitting as required at site complete all as specified and as directed

S&F Towel Ring round including taking down existing one complete all as specified and as directed.

S&F in repairs Overhead Shower rose 125mm size (Brass Chrome Plated) complete all as specified and as directed.

S&F in repair Chromium plated soap dish including fixing arrangement complete all as specified and directed .

S & F in repair tubular towel rail brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

S&F in repairs Glass self assembly of 12mm thick and n exc 60cm length, 15cm wide with stainless steel brackets, stainless steel railing in bathroom and fixed to wall with brackets complete all as specified and as directed

S&F Angular stop cock, chromium plated valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking existing one complete as directed.

S&F in repairs 40 mm Waste coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed one complete and all as specified and as directed.

S&F in repairs PVC waste pipe 32/40mm bore for WHB, Urinal & Sink complete all as specified and as directed.

Cleaning of air/dust blokages in the internal water supply lines concealed or fixed on the wall or floor surfaces by dismantling the fitting such as taps, valves, unions etc to facilitate/stimulate clearance of blockages/airlocks and re fixing the dismantled items after clearance of blockage/airlocks including fiiitngs etc complete all as specified and as directed

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unsericeable steel/plastic/cpvc water tubing and connections complete all as specified and directed.

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out old unserviceable steel/plastic/cpvc water tubing and connections complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank of 1000 Ltrs capacity cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe all as specified and directed.

S&F CP sink cock with swinging casted round shape spout screwed down screwed for iron pipe in repairs 15mm bore including taking down existing one complete all as specified and as directed.

S&F 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including taking down existing one complete all as specified and as directed.

Petty repair to toilet floor, bathroom, kitchen, etc seepage including sunken portion treatment with apply water proofing compound including repair and arrest the leakage to floor trap,nahani trap , grating and applying white cement etc making good to the damaged portion of flooring, laying and matching of existing flooring, complete all as specified and directed.

Petty repair to wall mixer,basin mixer,sink mixer etc including replacement of spindle brass, Jumper brass, rubber washer, head incl taking down and refixing ete all as specified and directed

S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed.

S&F Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

S&F in repairs CP 2 way bib cock with wall flange fancy type screwed down screwed for iron pipe in repairs 15mm bore complete all as specified and as directed.

S&F Plate rack of size 60 cm x 60cm (heavy duty) made of stainless steel fixed in repairs complete all as specified and directed.

Petty repairs to refixing the existing Wash hand basin and Sinks made of stainless steel 1mm thick kitchen flat back with including fixing cantilever CI/Angle iron brackets embedded in concrete block including connecting waste coupling 32mm bore, including bedding, waste fitting, waste pipe in cement mortar to dwarf wall and connecting union to pipe, filling gap in white cement and all necessary fittings to fixed in repair (including taking down and refixing in same position) complete all as directed.

M&L Vitrified Ceramic tiles 10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar (1:6) complete including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick, (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar (1:4) complete including dismantling of existing old tiles and disposal to outside MD land all as specified and as directed.

M&L for cement plaster rendering 5mm thick in CM 1:3 on fair faces of brickwork or concrete surface as on ceiling finished even and smooth with thin layer and taking down cement plaster on ceilings surface etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L preparation of newly plastered surfaces of ceiling and applying three coats of white washing on ceiling surfaces with smooth finish complete all as specified and directed.

M&L for providing and laying / fixing TPO membrane of non-flammable waterproofing of roof which shall be 1.5mm thick loose laid membrane using Fosroc Proofex ORG membrane, layers are overlaped to achieve a minimum weld of 110mm. Hot air welding can be either hand applied or by means of automatic machines and the roll's either end are overlapped with 110mm are in staggered position and the membrane shall be laid over the layers of non-woven geotextile fiber. The seperation layer provided to prevent the mechanical abrasion and cushioning between the fosroc proofex ORG membrane and the concrete substructure . The termination of fosroc proofex ORG by aluminium strip anchoring. Note: Work shall be executed directly by manufacturer or through their authorized and qualified applicators,of any following manufacturer only. M/s Fosroc chemicals, M/s Thermax Limited, M/s Tiki Tar Danosa India Ltd

M&L Machine cut kota stone slab 20-25 mm thick as in flooring, laid over and incl 20 mm thick screed bed in CM 1:3 set and jointed in neat cement slurry and pointed with cement and pigment to match the shade of the slab incl rubbing and polishing complete all as specified and as directed.

M & L for 100 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone agg) as in PCC in Hard standing etc. with , spike rolling ,or making impression of expanded metal, while the concrete is green complete all as specified and demolition of old concrete (un reinforced) of any description and in any position not otherwise specifically provided.

Dismantling structural steel work incl doors, gates but excluding framed trusses etc complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including dismantling of old sheets complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified incl dismantling of old sheet complete all as specified and directed.

S&F in repairs 0.56 mm thick Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed.

M&L for welding in repairs not exceeding 10 Cm length & thickness of metal to be welded not exceeding 6mm complete all as spcified and directed.

S & F MS Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and directed.

S&F in framed work as in doors or gates of angle,tubes or other section with gusset plates, rails, braces,guard bar etc., complete, to be prepared for hanging or sliding with and including hinges or steel hanging door fittings (exclusive of steel sheeting or other covering) and hanging; also fastening and fixing Fe 410 -W (Gde- E- 250) quality-A complete all as specified.

Taking down and refixing precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade over sand cushion with grey cement and no pigment and including side kerb concrete and removal and refixing all as specified and directed.

M&L for machine pressed pre polished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade over sand cushion with grey cement and no pigment incl removal of old and necessary demolition and all as specified and directed.

M&L for broken stone boulders hard core of guage n.exc 63mm deposited spread and level laid in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation and all as specified and directed.

M&L in repairs Pre-cast PCC 1:3:6 type C1 (20 mm graded agg) cement concrete block masonry with solid blocks exc. 10cm in width and set in cement mortar 1:6 including demolition of old brick work / stone masonry/PCC block built in cement mortar of any description as specified and directed.

M&L rendering 15 mm thick in CM 1:4 on brick surfaces finished even and smooth with out using extra cement all as specified and directed.

Excavation in trenches not exceeding 1.50 m wide and not exceeding 1.50 m deep along the existing sewage line carefully for placing taking out and getting out in any type of soil complete all as specified and directed.

Excavation in trenches exceeding 1.50 m deep and not exceeding 3.00 m deep along the existing sewage line carefully for placing taking out and getting out in any type of soil complete all as specified and directed.

Returning and filling soil in layers not exceeding 25cm thick each layer including spreading, leveling, watering and well ramming all as speicified and directed.

Removal of surplus material to a distance not exc 50 m and deposited where directred at a level not exc 1.50 m above starting point all as specified and directed.

M & L salt glazed stone ware drain pipes of internal dia 150 mm bore grade 'A' laid in trenches and jointed in cement mortar incl demolition and breaking up old drain pipe (salt glazed stoneware drain pipe) set in cement concrete, complete all as specified and as directed.

M & L salt glazed stone ware drain pipes of internal dia 200 mm bore grade 'A' laid in trenches and jointed in cement mortar incl demolition and breaking up old drain pipe (salt glazed stoneware drain pipe) set in cement concrete, complete all as specified and as directed.

M&L reinforced cement concrete pipes 150mm bore, class NP2, laid and jointed in position with collars incl demolition of old pipe complete all as specified and as directed.

M&L reinforced cement concrete pipes 200mm bore, class NP2, laid and jointed in position with collars incl demolition of old pipe complete all as specified and as directed.

M&L for concrete bed to drain pipe including packing under and haunching against the sides of drain pipe after they are laid and tested in PCC 1:3:6 type C-2 for 150mm dia all as specified and directed

M&L for concrete bed to drain pipe including packing under and haunching against the sides of drain pipe after they are laid and tested in PCC 1:3:6 type C-2 for 200mm dia all as specified and directed

M&L PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in foundation of manholes, drains, walls and similar works etc, ncluding demolition of existing cement concrete, including disposal of demolished material upto 500mtr MD land complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1(using 20 mm graded crushed stone aggregate) as in surface channel of drain, benching in manhole and wall / drain and similar works etc finished even and smooth with using extra cement ncluding demolition of existing cement concrete, including disposal of demolished material upto 500mtr from MD land complete all as specified and directed.

M&L for Providing Plain cement concrete 1:2:4 type B1 (20mm graded stone aggregate) as in coping and similar works etc, including removal of old and necessary demolition, complete all as specified and directed.

Cutting into existing manholes for connecting new drains any bore, making good to pipe and rendering cutting out existing banching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as reuired complete all as specified and as directed.

Cleaning of manholes any size and depth n exc 1.5m including lifting, removing sludge, water and cleaning with water using mechanical instrument including cutting grass, vegetation and bushes to a width of 60cm all alround manholes complete all as specified and directed. Note : the sludge obtained while cleaning shall be removed from the site to outside of MOD land. The rates quoted for items shall include the above provns also.

M&L Cleaning/ clearing of sewage line (including manholes) 150 mm to 300 mm dia main line from 1st manhole onwards bore of any description, underground at any depth, removing any type of blockage including desludging, descaling & decoking of drain as well as manholes with combined high pressure water jetting cum suction (vacuum) type machine mounted on LCV/HCV /LMV/HMV and having facilities of high pressure vacuum and provn of hydraulic through high pressure thermo plastic fiber based water jetting hose and conical round shape nozzle pipe and flushing after cleaning including removing the same out side MD land and deposit where the place marked by the local municipality, complete all as directed.

Attending day to day complaints of different type of sewage work such as removing blockage of WCs, floor traps, Nahani traps, Gully traps, CI/PVC pipes all types any size, any height top to bottom including junction etc complete all as specified and directed.

Cleaning of manholes any size and depth exc 1.5m including lifting, removing sludge, water and cleaning with water using mechanical instrument including cutting grass, vegetation and bushes to a width of 60cm all alround manholes complete all as specified and directed. Note : the sludge obtained while cleaning shall be removed from the site to outside of MOD land. The rates quoted for items shall include the above provns also.

Cleaning of blockage from nahani traps of bathroom/kitchen/Urinal/toilet in ground floor and upper floors all types any size, any height by taking out mud/sand incl taking out lid and re-fixing the same complete all as specified and as directed.

Cleaning of blockage from Gully trap to 1st manholes in ground floors, all types any size, any location by taking out mud/sand incl taking out lid and re-fixing the same complete all as specified and as directed.

(a) Cutting and filling shall be cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground digging out of roots shall be made good carefully by filled up with moorum/red bajri well rammed and levelled.

(b) Safaiwala shall report to concerned JE /AGE in service centre B&R daily including Sunday and holiday and get the job card for carrying out the work. The Job card shall be returned to concerned JE/AGE duly signed by the users as a token of completion of job.

(c) Cleaning, removal of silts/wastage of organic or inorganic materials of Sewage line of 100mm to 450mm bore up to 1st manhole, in between manholes, GT Chamber, etc to maintain sewage system functional all days including Sundays and holidays along with necessary T&P i.e flexible rods, cleaning pumps and safety kits etc.

(d) The complaints to be rectified within SIX hours on same day. In case of delay in rectification of complaint for more than Six hours, the penalty will be levied @ Rs.100.00 Per complaint/ day.

(e) In case the nature of job is such that the work cannot be completed within a period of 6 hrs then the same shall be brought to the notice of the GE/Engr-in-Charge and the period for the completion of the complaint shall be decided by the GE/Engr-in-Charge.

Taking out/pumping contaminated sewage water/ sludge from septic tank/soakage well/ incl inlet/outlet chamber after plugin incoming sewage line suction (vaccum) type machine mounted on LMV/HMV and facility of high pressure vaccum and removing and dumping off the same in tank to a place out side contonment at the place marked for the purpose by local municipality or the authority controling the area as directed. Note :- Contractor is advised to ascertain the suitable place earmarked for disposal of sludge/sewage water from local municipality or area controling authority before quoting their rates. Disposal of waste at suitable place shall be sole responsibility of contractor and no representation or objection in this regard shall be entertained at any later stage.

M&L Cleaning and Removing silt, grit , mud and other materials from covered drain in foul condition including removing materials from the site to outside MD land including necessary removing cover slabs and replacing after cleaning complete area including making good any damages complete all as specified and as directed. Note :- The unit rate is deemed to be included for Removing of accumulated earth at sides of drain of any width and depth up to 30 cm. cleaning/cutting the grass around 1 m from drain (both sides) and removing the grass waste to outside MD land. Cutting and filling shall be cleared of shrubs, vegetation, grass bushes, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level . Cutting the grass/felling of trees shall include digging out roots up to 60 cm below the ground level or 14 cm below the formation level, whichever is lower. All holes and hollows formed in the ground after digging out of roots shall be carefully filled up with moorum/red bajri well rammed and levelled.

M&L for kerb stone precast with PCC (1:2:4) type B1 using 20mm graded aggregate finished even and fair without using extra cement and all as specified and directed and demolition of old kerb stone (un reinforced) of any description and in any position not otherwise specifically provided.

M & L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) setting in CM 1:6 work for landings, cover slabs, manholes, chajjas, water troughs, manger shleves and similar articles with plain faces and demolition of old reinforced cement concrete of any description and in any position and complete all as specified and directed.

M & L mild steel TMT bar 10mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, chajja, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of old decorated wall surfaces including cleaning with water, rubbing of fungus complete removal, applying two coat of weather proof paint "APEX" exterior wall paint including necessary preparation to give uniform and smooth finish all as specified and directed.

M&L for machine pressed pre polished precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade except Interlocking tiles. over sand cushion with grey cement and no pigment, incl removal of old and necessary demolition and all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 40mm graded aggregate as sub base/hard standing etc incl demolition all as specified and directed.

Dismantling posts or struts (wood, steel, or RCC) any section, any length n exc 5m including taking out embedded portion in concrete, brick work, masonry etc and all as specified and directed. and incl neccessary excavation for new post holes all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 (using 40 mm graded stone agg) as in foundation, filling and for mass concrete all as specified and directed.

S & F MS angle iron Hand rails, fencing posts, flat iron including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only of chain link fencing MS galvanised square wire mesh, dia of wire 4mm including line wires, to any type of standard rails, straining bolts, etc all as specified and directed.

Fixing only in repairs chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc inlcuding provision of binding wire and dismantling of old unserviceable fencing wire mesh of any type etc all as specified and directed.

M&L for Preparation of new surfaces of steel and applying 2 coat of synthetic enamel paint over one coat of redoxide primer complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description all as specified and directed.

S&F in repairs MS round bars 10 mm dia and over Fe 290 (Gde - E-165) cut to length bent to shape required including cranking, bending spirally, hooping for columns, hooking ends and all as specified and directed.

S &F in repairs Mild steel screw bolts (machine made) dia of neck 16 to 20mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long all as specified and directed.

M&L for welding in repairs not exceeding 10 Cm length & thickness of metal to be welded not exceeding 6mm complete all as spcified and directed.

S&F Welded steel wire fabric cut to length, bent to shape required and tying with and including annealed mild steel not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members not exceeding 4kg/sqm complete all as specified and directed.

M&L in repair to steel gates area n exc 16 sqm oiling, greasing, welding, replacement of metal parts as required and clean the wheel track and apply with grease and make to move smoothly all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces on external surfaces finished even and smooth without using extra cement and Taking down cement plaster on brick or stone walls, or concrete or ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises and leaving the work clear of any plastering

M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces with smooth finish of any description, complete all as specified and as directed.

M&L for treating with three coats of whitewash on new surfaces of walls incl necessary preparation to give uniform and smooth finish all as specified and directed.

M&L in repairs 300mmx300mmx25mm thick prepolished cement concrete chequered tiles jointed in neat cement slurry and pointed in white or coloured cement to match the floor and including 20mm thick screed bed in CM 1.4, including removal of old and necessary demolition, all as specified and directed.

M & L in repairs walling of random rubble, uncoursed, Bangalore type masonry well bonded bedded solidly hearted built in CM 1:6, extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified, key pointing to random or polygonal rubble, uncoarsed or brought upto courses in CM 1:4 and including demolition of old brick work / stone masonry/PCC block built in cement mortar of any description as specified and directed.

Walling random rubble, uncoursed, Bangalore type masonry (except stone) well bonded bedded solidly hearted built in CM 1:6, extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified, key pointing to random or polygonal rubble, uncoarsed or brought upto courses in CM 1:4 and including removal and refixing, built in cement mortar of any description as specified and directed. (Old stones shall be re-used)

Racking out joints /points in cement mortar to squared rubble masonry coursed or uncoursed and incl M&L keyed pointed in CM 1:4 for squared rubble masonary as specified and directed.

M & L broken glass coping on top of walls in cement mortar 1:3 incl taking down old glass and removing the rubbish to a distance not less than 100 m and deposited where directed.

S&F in repair galvanised two strand steel barbed wire 2.24 mm dia barbed wire with 2 mm barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised MS wire staples or steel pins etc as directed (each line wire to be measured)

Restraining and resecuring barbed wire including making good staples etc (each line wire to be measured)

S & F in repair concertina coil of 610mm dia (in stretched position) hot deep galvanised steel wire coated with CLR ante corrosive coating making diamond shape with the help of devotail clips (18 SWG) fixed over barbed with the angle iron the concertina coil is to be fixed with barbed wire at points where coil touched the bottom barbed wire with the help of hog rings (14 SWG) complete, incl removal of old unserviceable coil all as specified and directed.

M&L in repairs Providing precast cement concrete lowvres and jallies, 35mm thick (measured solid) set in CM 1:4, type B0 1:2:4 , faces are finished smooth including demolition of old mouldings complete all as specified and directed.

Site clearance by Scraping of grass/wild growth/trees cutting n.exc 0.30m girth etc in any type of soil by manually/mechanically including removing of rubbish from the site to a distance exc, 250m but n. exc 500m and deposited where directed at a level not exc. 1.5m above the starting point, complete all as specified and as directed

M & L for 75 mm thick PCC type C1, 1:3:6 (20 mm graded stone aggregate) as in plinth protection finishing the surface even and smooth with using extra cement, including necessary demolition of old concrete all as speecified and as directed.

M&L for preparation of new/old any type of surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of floor guard paint over a coat of red oxide primer complete all as specified and directed.

Note :- An amount of Rs 1,19,286.00 on account of credit schedule for schedule 'A' part II shall be deducted from the total amount of BOQ to arrive at the contract sum.

SREE BUILDERS (BID ID -3497882)

A.GOVINDARAJ (BID ID -3498670)

LAKSHMI CONSTRUCTIONS (BID ID -3500001)

UNIVERSAL ENGINEERING (BID ID -3499443)

Moulya Builders (BID ID -3499001)

devan enterprises (BID ID -3499132)

RAMESH BABU CO (BID ID -3497656)

NORTH INDIA PEST CONTROL (BID ID -3500126)

M/S SRI BALAJI ENTERPRISES (BID ID -3502260)

Maruthi constructions (BID ID -3497517)

RMK PROJECTS (BID ID -3501931)