GE/PNH-38/2023-24

Amount

B&R PORTION: M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

M&L for preparation of old painted steel surfaces/CGI/PGI sheets of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern, complete all as specified and directed.

M&L for preparation of old wall surface and applying one coat of cement base paint, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Refixing steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls in new or old position Complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

Refixing steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls in new or old position Complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for 20-25 mm thick machine cut Kota stone slab flooring, bedded and jointed with grey cement slurry and pointed with grey cement with admixture or pigment to match the shade of Kota stone slab as approved by GE, laid over and including screed bed or bedding layer of mortar 20mm thick in Cement Mortar (1:6) including cutting, grinding and mirror polishing complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in base course to floor, finishing surface even and fair to receive floor finishes, ,complete all as specified.

Demolition or breaking up drain pipe (salt glazed ware, AC, PVC or reinforcement concrete) of any size, set in cement mortar/concrete, complete all as specified.

M&L for Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm drain pipe after they are laid in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) & tested, complete all as specified and directed.

M&L for Plain cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified and directed.

M&L for 50 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base of sunkun portion/ floor finishing surface even and fair,complete all as specified and as directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 m in length) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for Precast reinforced cement concrete Type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate) as in cover slabs (for manhole etc), chullah hoods, chajjas, water troughs, mangers, shelves etc and setting in cement mortar 1:4 including necessary formwork complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for glazed ceramic coloured tiles (450x350mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick, built in cement mortar (1:6), complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or finished concrete surface in cement mortar 1:4 with mixing of liquid water proofing compound @ 3 % of cement and finished the surface even and smooth without using extra cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for rendering 5mm thick on fair faces of brick or finished concrete surface in ceiling in cement mortar 1:3 with mixing of liquid water proofing compound @ 3 % of cement and finished the surface even and smooth without using extra cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for rendering 10mm thick on fair faces of brick or finished concrete surface in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 for laying sunkun/ roof treatment and finished the surface even and smooth without using extra cement and using water proofing compound on concrete surface @3% by weight of cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for Water proofing treatment to RCC sunken Slab complete all as specified and as directed by Engineer -in- Charge as per following:- (a) Cleaning the surface with wire brush / coir brush, removing lose material like dust particles, dirt etc. (b) Creating filet covering of 50X 50 mm with polymer modified mortar on the junction of slab and walls (c) Apply first coat of two component modified polymer coating on the horizontal and verticale surface (d) Provision of glass fiber mesh of 2X2 mm immediately on above coating (e) Apply second coat of two component modified polymer coating after 72 Hrs (f) Joining the sanitary pipes with the water proofing tape having bridgingability of more than 1.5mm (g) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout (h) Complete the treatment to be carried out by authorised applicator of water proofing manufacturer as per Make approved by E-in-c's branch.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

S&F pressed steel frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges 100mm long, 03 Nos each for double shutters, lock strike plate, etc., complete all as specified and directed.

S&F pressed steel frame of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges 100mm long, 03 Nos each for double shutters, lock strike plate, etc., complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame with 3 Nos stainless steel hinge 100mm size, welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per manufacturer's instructions complete all as specified and directed.

M&L for 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F 300mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

S&F sheet glass ordinary quality, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

S&F frosted glass pane ordinary quality 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

S&F steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified and directed.

S&F in repair bib tap 15 mm bore with flange, brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair angular stop valves cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with capstan head screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair stop valve (concealed) cast copper alloy 15 mm dia, fancy type with long shank chromium plated with wall flange screwed down, high pressure, with capstan head screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or Equaivalent cat part of make as specified in P.S.

M&L for providing edge moulding to 18-20 mm thick stone of counters vanities etc including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 600mm complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia, D type, 600 mm long between flanges complete all as specified and directed.

S&F in repair 32mm dia PVC waste pipe 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 110mm dia provided with access door, complete all as specified and directed.

S&F in repair PVC (SWR) bends of any radius 75 mm dia provided with access door, complete all as specified and directed.

S&F in repair PVC (SWR) branch piece of any radius 110mm dia double (double 'Y') equal or unequal, complete all as specified and directed.

S&F in repair 75 mm dia PVC floor trap with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe(vent pipe) including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 75mm dia suitable for pipes including clamps, complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

S&F in repair 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

Taking down existing roof treatment of any description in any condition including removing of cement plaster of concrete of any description from the roof surfaces and removing all the debris to a distance n.exc 100m and roughening surfaces by sweeping clean and washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3 Kg/Sqm over cleaned surfaces and providing 10 mm thick cement screed in CM 1:4 , finished surface even and smooth, after that cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with one coat of industrial bituminious primer at the rate of 0.40 lit/Sqm over the plastered surfaces of roof and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C @ 1.2 kg/sqm then applying APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 150 mm overlap primed surfaces by forced (tourch) application as per manufactures instructions and applying two coats of aluminium paint over APP membrane, complete all as specified and directed.

S&F TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

M&L for chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed with mixture of white and grey cement in equal proportion and no pigments, laid over and including 20mm thick screed bed in CM 1:6,complete all as specified and directed.

E&M PORTION: Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One ligh point controlled by two numbers, two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

All as per srl item No 77 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F in repair ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp two way, (ISI marked), complete all as specified and directed.

S&F in repair Switch socket combination, 5 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

Supply and fixing in repair inverter LED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells cat part No. LHEXACP7FN1W020 or equivalent make as specified in PS

S&F in repair LED inverter lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDEUEEML8R010 or Equivalent cat part of make as specified in Appx 'A' to P.S.

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver including suitable bracket fixed to wall/ pole complete with IP 65/66 protection complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

Supply, laying , jointing and testing in repair of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 16 sqmm 2 core, laid in trenches/ducts or fixed to poles/walls or laid under roads/paths/drains/culverts including cable gland of suitable sizes and aluminium lugs for connection, complete all as specified and directed. Make: Finolex / KEI Industries Pvt Ltd / Polycab / Gloster / Universal Cables. Note: Excavation, earthwork, sand cushioning, brick protection shall be measured & paid for separately.

Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in any type of soil complete all as specified and directed.

Returning, filling in surplus spoil including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed.

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for Sand cushioning to under ground cable providing with a layer of Sand 08 cm thick before laying of cable and 15 cm after laying of cable in trenches, hand punning complete all as specified and directed by Engr-in-charge (Note : Punning thickness of 18 cm will be measured for payment purpose)

M&L for Burnt bricks locally available, sub class 'B', laid flat for protection of under ground cable complete all as specified and directed at site.

S&F in repair Tubing 'light grade' galvanised iron with all fittings and fixed to poles, walls etc. with flat iron clamps/bolts/nuts/washers or laid in floors/under roads complete of size 40 mm bore, complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

JAMWAL CONSTRUCTION CO

SUNIL KUMAR SANGEET KUMAR AND SONS

M/S KEWAL KRISHAN SANJEEV KUMAR VAID

NATIONAL TRADING COMPANY

narayan construction

M/S Farooq Ahmed Bhat