REPAIRS AND REPLACEMENT OF FENCING, BOUNDRY WALL, AREA DRAINAGE, FOOTPATH, SEWAGE LINE, MANHOLES, SEPTIC TANKS, CLEANING OF SEWAGE LINES/ MANHOLES/ SEPTIC TANKS/WATER TANKS INSIDE DRDL UNDER AGE B/R -1 HYDERABAD

Amount

Dismantling of (steel, wood, or RCC) posts or struts embedded in ground, of any section including taking out embedded portion and making good disturbed ground, complete all as directed.

All as per item No.1 here-in-before but posts embedded in concrete, brick work, masonary, etc, complete all as directed.

Demolition of stone masonary built in cement mortar including all quoins, arches, pillars, copings etc, complete all as directed.

M&L for walling of squared rubble masonary, Secunderabad type, well bedded, bonded and solidly hearted built in CM (1:4) , complete all as directed.

All as srl item No.4 here-in-before but except stone

M&L for broken glass coping on top of wall in CM (1:3), complete all as directed.

M & L for TMT bars 10mm dia and over cut to length bent to shape reqd including cranking bending spirally for hoping columns hookings ends binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as directed.

M & L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binder, including binding with mild steel wire not less than 0.9 mm dia or securing with clips, complete all as directed.

M&L Pre-Cast RCC (1:2:4) Type B1 (20mm graded stone aggregate) as in cover slab drains and similar articles including formwork with plain faces and set in cement mortar (1:4) including demolition of old reinforced cement concrete complete all as directed. Note : Reinforcement shall be Measured and paid seperataly under relevant items.

M&L for providing pre cast RCC 1:2:4 type B-1, (using 20mm graded stone aggregate) as in posts, struts etc area exc 100 and n exc 250 Sqcm with or without chamfered angles complete all as directed. Note : Reinforcement and formwork shall be Measured and paid seperataly under relevant items.

M&L plain cement concrete (1:3:6) Type C2 (using 40mm graded stone aggregate) as in surface channels and drains, etc., including use and waste of necessary Form Work, including demolition of old concrete complete all as directed.

M&L for plain cement concrete (1:3:6) Type C2 (using 40mm graded stone aggregate)75 mm thick as in Plinth protection , etc., finishing the cement include joints concrete surface even and smooth without using extra cement, including Use and Waste of necessary Form Work, including demolition of old concrete complete all as directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), 100mm thick as in hard standing, finished even & smooth without using extra cement including demolition of old concrete complete all as directed.

M&L for plain cement concrete (1:2:4) Type B0 (using 12.5mm graded stone aggregate) as in kerbs, copings, roof kerbs, etc., chamfered edges including use and waste of formwork as required including demolition of old concrete complete all as directed.

Removing/dismatling of rusted and unserviceable barbed wire fencing of any size (each line) and in any position, complete all as directed.

S&F Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire, staples and pins etc, complete all as directed.

All as per srl item No.16 here-in-before but fixing only (material obtained from item No.15 shall be used).

Restraining, resucuring including making good staples etc., for steel barbed wire barbed with any dia barbs at any spacings, complete all as directed.

S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standard rails, straining bolts including provision of binding wire, including old damaged chain link fencing complete all as directed.

Supply only chain link MS galvanised fencing of , any type or size, complete all as directed.

S&F MS work as in fencing post and strurts including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillet ( for securing wire mesh etc) including all necessary drilling, bolting, riveting etc and similar work confirming to Fe-290 Gde E-165 including taking down old MS work, complete all as directed.

S&F Welded steel wire fabric to wood or steel members, weight n.exc 4 Kg/Sqm, including taking down old steel wire fabric complete all as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates,rails, braces, etc. complete drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting rails and guides) conforming to Fe-290(Gde E-165)including dismantling old framed work complete all as directed.

M&L for brick work with sub class 'B' , old size bricks, straight or curved on plan exc 6.00m mean radius, built in CM (1:6), including demolition of old brick work complete all as directed.

M&L brick work with sub class 'B' old size bricks straight or curved on plan to any radius in half brick thick built in CM 1:4, including demolition of old brick work complete all as directed.

M&L for 15 mm thick rendering in cm 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, including taking down cement plaster of any description, racking out joints , hacking for key, scrubbing down with water complete all as directed.

M&L for rendering 15mm thick in CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement, complete all as directed.

Complete removal of exisitng treatment on wall surfaces and applying of two coats of oil bound distemper over one coat of primer over one coat of wall care 3 mm thick (1.5 each) putty, complete all as directed.

M&L for preparation of new plastered surfaces of walls and applying two 3 mm thick (1.5 each) putty coats of oil bound distemper over a coat of primer over a coat of wall care putty complete all as directed.

M&L for preparation of of new plastered surfaces of walls and applying two coats of cement base paint, white or tinted over a coat of primer complete all as directed.

M&L for flush pointing to squared rubble masonary in CM (1:4), including racking out existing cement mortar joints complete all as directed.

M&L for raised pointing to squared rubble masonry brought upto courses in cement mortar (1:4), including racking out existing cement mortar joints complete all as directed.

M&L for 30mm thick Paving tiles of size 380mm x 380mm using white cement and pigments with wear resistant coating of approved design laid with cement slurry @ 3Kg/ Sqm over 15mm thick screed bed in cement mortar 1:6, including dismantling of old tiles along with screed bed complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate) as in sub base of floors finished even and fair, including demolition of old concrete complete all as directed.

Cleaning of weeds, mud, sand, etc from storm water drain including, excavating of rubbish in foul condition and removal from site , complete all as directed.

S&F 3mm thick PVC tiles/sheets laminated plain coloured marbled mosaic or mottled finish laid with approved rubber based adhesive in floors, including dismantling of existing floor, complete all as directed.

M&L for Preparation of new Steel and iron surfaces of any description exc 10 cm width or girth and applying 2 coats of synthetic enamel paint over a coat of red oxide primer, complete all as directed.

M&L for Preparation of old treated steel and iron surfaces of any description exc 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated /trepezoidal steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws including dismantling of old corrugated roof covering complete all as directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in ridges fixed with self tapping screws including dismantling of old ridges complete all as directed.

S&F for structural steel work for rolled sections as in main and cross beams, hips and jack rafters, purlins, running rails and guides for sliding doors, fixed with angle cleats or other connecting plates of gde Fe-410-W, including taking down old structural steel work complete all as directed.

S&F for MS work as in Bands, straps, supports or stays for RWP, ventilating pipes, gutters including bolts, if reqd hooks (stay), clamps, holdfasts, wall ties, nosing angles, hooks for hanging fans and similar small articles conforming to Fe-290 gde E-165, including taking down old MS work complete all as directed.

S&F in repairs, 1.60mm thick Mild steel plain black sheet in water troughs, gutters, wall cladding, ducts, etc cut to size, profiles, edges beaded if reqd, holes punched, including round headed screws, clout nails or rivets and fixed to steel members etc with 40mm lap joints or welded/riveted seams including bending, turning, etc as required, complete all as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated etc) sheets in roof covering including ridges, north light roofing, etc,, compete all as directed.

S&F 6mm thick asbestos cement corrugated or semi corugated sheets in roof covering fixed with 'L' or 'J' type hook or cranked hook, bolts complete all directed.

All as per Srl Item No. 46 here-in-before but fixing only AC corrugated sheet complete all as directed.

M&L Asbestos cement single piece adjustable serrated ridge for corrugated or semi corrugated sheets, complete all as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, laid in trench, including taking down old unserviceable pipes complete all as directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as directed.

S&F in repairs Rectangular aluminium hollow section, powder coated of approved colour (thickness of powder coating not less than 50 mircon), of size 101.60 mmx 44 mm x2 mm thick as in partition including fixing with suitable size nuts, bolts in floors and walls by drilling holes, both vertical and horizontal members including provision of sheet glass 4.8 mm thick and 12 mm thick particle board prelaminated on both side with decorative choice lamination, aluminium lugs, aluminium glazing channel, rubber beading, including taking down old aluminium partition along with panels complete all as directed.

S&F in repairs Powder coated (thickness of powder coating not less than 50 mircon) aluminium door shutters with aluminium chowkat, aluminium section weghing 0.55 kg/m including necessary 12 mm thick prelaminated particle board, 4.8 mm thick glass,joining cleats, glazing clips, rubber neoprene packing handles (200 mm long) 2 Nos in each doors, hinges, anodised aliminium snap beading tower bolt etc. complete all as directed.

S & F in repairs Anodised powder coated window shutters side hung/sliding, without sash bars aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, neoprene rubber packing, handles- 01No in each shutter, hinges 2 Nos/rollers, snap beading, complete all as directed.

S & F in repairs, Aluminium anodised or powder coated grill type 'A' fixed to aluminium windows, complete all as directed.

Taking down existing venetian blinds of any type completely with fittings and supply and fix new venetian blinds of 100mm wide fabric straps, vertical type including all necessary fittings of approved colour to match the existing size and quality, complete all as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins or spring clips and S&F 3 mm thick sheet plain glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as directed.

Cleaning of sewage lines of 100mm dia by rodding from manhole to manhole removing the materials obtained from sewage line including cleaning of manholes and flushing with clean water complete all as directed.

All as per item No.57 here-in-before but 150mm dia

All as per item No.57 here-in-before but 200mm dia

Cleaning of Gully traps of any size and of any depth by removing the material (sludge materials) and placing back the manhole cover in Position complete all as directed.

Cleaning of Septic tanks of 10 to 25 users capacity by dewatering all the water, taking out the sludge/night soil, in order to remove all stacked mud/sludge etc., cleaning the chocked inlets, outlets of septic tanks, removing all the sludge outside MD land, complete all as directed

All as per item 61 here-in-before but Septic Tank of 50 Users capacity

All as per item No.61 here-in-before but Septic Tank of 100 Users capacity

All as per item No.61 here-in-before but Septic Tank of 150 Users capacity

All as per item No.61 here-in-before but Septic Tank of 250 Users capacity

M & L for removing of soaked material from the existing soakage pits of any size and from any depth in foul conditions, and refilling, spread and laying new broken brick bats of gauge 80mm to 150mm in 25cm thick layers including spreading leveling complete all as directed.

Removing of blockage from 'S' trap/'P' trap/ Nahani trap/floor trap by flushing or by sucking by suction pumps at GF/Ist/IInd/ IIIrd floor including cleaning the line up to 1st manhole complete all as directed.

Clearing the urinal blockage of any length and dia by Roding and removing the materials (sludge) to a distance not exceeding 50m all as directed.

Clearing WC blockages up to 1st manholes of any length and dia by rodding and removing the materials (sludge) to a distance not exceeding 50m complete all as directed.

Cutting into existing manholes for connecting new drains of internal dia of pipe 100mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round and 3/4 section) in cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) smooth finished and reforming benching as required complete all as directed.

All as per Sl item 70 here-in-before, but for internal dia of pipe 150mm complete all as directed..

All as per Sl item No.70 here-in-before, but for internal dia of pipe 225mm complete all as directed.

Excavating in trenches n. exc 1.5m wide and n.exc 1.5m in depth and getting out in hard/dense soil complete all as directed.

All as per Sl item No. 73 here-in-before but depth exc 1.5m and n.exc 3.0m complete all as directed.

Excavating in trenches n.exc 1.50m deep and getting out in soft/disintegrated rock for foundations, manholes etc complete all as directed.

All as per Sl item No. 75 here-in-before but depth exc 1.50m but n.exc 3.00m complete all as directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone agg as in foundation/mass filling including demolition of existing concrete complete all as directed.

M & L for salt glazed stoneware drain pipe of 100mm dia grade 'A' laid in trenches and jointed in cement mortar (1:2) including demolition & breaking of old pipe complete all as directed.

All as per srl item 78 here-in-before but of 150mm dia

All as per srl item No.78 here-in-before but of 200mm dia

M & L for plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes of 100mm dia including packing under and haunching against the sides of pipes with concrete after they are laid and tested complete all as directed.

All as per srl item No.81 here-in-before but for pipe of 150mm dia

All as per srl item No.81 here-in-before but for pipe of 200mm dia

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed.

Removing excavated soft disintegrated rock to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick using soil complete all as directed.

S & F in repairs cast iron Nahani trap of size 75mm dia, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1, complete all as directed

All as per srl item No. 87 here-in-before but 100mm dia

Cutting of existing road of any type and up to any depth, laying the CI pipe in required slope, jointing, refilling the excavated material and making good the road surface by putting 100mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) complete all as directed.

S & F Hume pipe septic tank of capacity 25 users, including necessary excavation earth work , AC vent pipe, Precast cover, PCC bed, etc and demolition of old septic tank complete all as directed.

Cleaning of Roof gutter including water outgoing holes at any hight of building, removing the materials (sludge) to distance n exc 50m, complete all as directed.

Cleaning of Rain Water pipes and removing the materials (sludge) to distance n exc 50m, complete all as directed.

Cutting of plants and grass growth on bldg's roofs, chajjas and branches coming on bldgs (at any floor and any height) and removing the material (Branches and plants ) to a distance n exc 50m, complete all as specified and directed .

Cleaning of Roof sorrounding area, mud, tree leaves etc including water outgoing holes at any hight of bldg, removing the materials (sludge) to a distance n exc 50m, complete all as directed.

Taking down of aluminum door shutters / wooden door shutters of any description and of any size, and re-fixing the same door shutter in same opening after easing and perfectly closing / opening by using necessary alignment for proper functioning and making good to the damaged portions complete all as directed.

S & F in repairs door closer hydraulically regulated, aluminum body (Die cast), designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg complete all as directed.

S&F in repairs vitreous china white wash down water closet pan, pedestal pattern including fixing bolts, 'P' or 'S' trap, plastic water closet seat and cover with recessed bottom with MS CP hinging device (excluding flushing cistern and flush pipe) complete all as all as directed.

S/F in repairs vitreous china Orrissa pattern 'squatting pan', white of size 580x440mm with integral foot rest (excluding flushing cistern and flush pipes) but with its cement concrete bedding and ‘P’ or ‘S’ trap, including PVC pipe upto finished floor level to connect flush pipe, making good all the disturbed surfaces to match with the adjoining surface complete all as directed.

S & F in repairs Vitreous china, white, urinal, full stall type including providing PTMT spreader and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long screws, pointing around urinal back in cement connecting water pipe and waste pipe complete all as directed.

Taking down chowkats or frames (without taking out shutters from frame) area exc. 1.5 Sqm and n exc. 4 sqm each, complete all as specified and as directed.

Taking down chowkats or frames (without taking out shutters from frame) area n exc. 1.5 Sqm complete all as directed.

Taking down shutters of any description area exc. 1 sq m and n exc. 2sq m each, complete all as directed.

S & F Second class HW plain solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as directed.

S & F 2nd class Hardwood factory made plain, framed, panelled door shutters of 35mm thick (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and style as per IS: 1003 (Part-I) kiln seasoned and chemically pressure treated, complete all as directed.

S & F Flush shutter 35mm thick, solid core construction with block board core and plywood face panels commercial type on both sides, complete all as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as directed . Make :- SINTEX / RAJSHRI PLASTIWOOD/ NANDI/ UNIVERSAL

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, complete all as directed.

S & F mild steel butt hinges 100mm long, medium weight, cold rolled, complete all as directed.

S & F Aluminium anodized, barrel tower bolt 200mm long of extruded section, complete all as directed.

S & F Aluminium alloy anodised handles 150mm long, cast type, complete all as directed.

S & F Aluminium alloy, anodised sliding door bolt 300mm long, with hasp, staple (Bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as directed.

M/L 25 mm thick plain cement concrete 1:2:4 type B-1 ( using 12.5 mm graded stone aggregate) as in sub base of floors finished even and fair, including demolition of old concrete complete, all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 mm thick area of each tiles exc o.11 sqm but n.exc 0.18 sqm as in floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement to match , over 15 mm thick screed bed in CM 1:6 including taking down the old tiles along with screed bed complete all as directed.

M&L for Coloured glazed ceramic tiles 450 x 350 x 7mm thick on vertical surfaces of walls as in dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over a backing coat of 10 mm thick in CM 1:3 including dismantling of old tiles along with backing coat, complete all as specified and as directed.

S&F Vitrified ceramic tile 10mm thick Light shade (square/rectanguler) polished, area of each tile exc 0.36 Sqm and n exc 0.42 Sqm in flooring set and jointed in neat cement slurry and pointed in coloured cement to match, over existing floor ,including 15mm thick screed bed in cement mortar (1:6), including dismantling of existing tiles alongwith screedbed complete all as directed.

M&L for 20mm thick acid resistant tiles vitreous ceramic,unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors including dismatling old existing tiles complete all as directed.

S&F in repairs 15mm dia bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, high pressure screwed for iron pipe, complete all as directed.

S&F in repairs 15mm dia pillar taps cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe, complete all as directed.

S&F in repairs 15mm dia stop valves cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe, complete all as directed.

S&F in repairs 15mm dia bib tap standard of PTMT, any colour high pressure screwed for iron pipe (minimum weight 90gms), complete all as directed.

S&F in repairs 32mm dia PVC flexible waste pipe of length exceeding 60cm but not exceeding 90cm with connector suitable to connect the pipes with waste fitting/ coupling of WHB/ sink/ urinal, complete all as directed.

S & F in repairs PVC valve less, syphonic action type, flushing cistern 10 ltr capacity, low level, white, with inlet ball valve float and handle along with suitable flush pipe/bend including brackets, complete all as directed.

S&F in repairs grating doom 140mm size of PTMT complete all as directed.

S&F in repairs PVC connection of 15mm size with PTMT nuts of length 600mm, complete all as directed.

S &F in repairs galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as directed.

sanjar enterprises

Sai construction & services

M/S GDR CONSTRUCTIONS

M/S VASU ENGINEERS