PROVISION OF RIK STORE ROOM, SITTING AREA IN TRV AND CERTAIN WORKS IN JUNIOR SAILOR ACCN AT COAST GUARD UNDER GE HADDO SRI VIJAYA PURAM

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc not exceeding 10 sqm on plan and n.exc 1.5 m in depth and getting out in hard / dense soil etc complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm hard dense soil complete all as specified and as directed.

Removing excavated material n.exc, 50 m and depositing where directed at a level n.exc, 1.5m above the starting point complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete etc all as specified and as directed.

M&L for form work to sides of concrete foundations, footings, raft and raft beams, sides and soffits of foundatrion and plinth beams and similar work for rough flat surfaces complete all as specified and as directed.

M&L for form work to sides of columns and similar works for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to lintel beams, roof beams, chajjas and similar works for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slabs, shelves and similar articles set in cm 1:6 finished even and smooth with necessary form works etc all as specified and directed

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including crancking, bending spirally hooping for columns, hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and up to 10mm dia as in stirrups, cut to length, bent to shape requiried, including brancking, bending spirally hooping for columns, hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

M&L for Reinforced cement concrete Type A1 1:1.5:3 using 20mm graded aggregate as in foundations/footings, plinth beams, bases for column, etc., complete all as specified and as directed.

M&L for Reinforced cement concrete Type A1 1:1.5:3 using 20mm graded stone aggregates as in columns, pillars etc complete all as specified and directed

M&L for Reinforced cement concrete Type A1 1:1.5:3 using 20mm graded stone aggregates as in lintel beams, roof beams, chajjas etc complete all as specified and directed

M&L Precast cement concrete block masonry exc 10cm in width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) etc all as specified and as directed.

M&L for Rendering 10mm thick in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth without using extra cement etc all as specified and as directed.

M&L for Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement etc all as specified and as directed.

M&L for preparation of newly plastered Internal wall surface and applying two coats of distemper oil emulsion over a coat of primer over the coat of 1 to 2 mm thick wall care putty etc complete all as specified and as directed.

M&L for preparation of surfaces and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out and removing surplus/excavated soil to a distance n exc 50 m where directed etc complete all as specified and as directed.

M&L for cement concrete Type C-2, 1:3:6 (using 40 mm graded stone aggregate) in post holes or in simillar works etc complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC type D-2, 1:4:8 (using 40mm graded aggregate) 75mm thick as in sub floor, sub base floor and pavings etc complete all as specified and as directed

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, dark shade with border design, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including cement screed bed 15mm thick in cement mortar 1:6, etc complete all as specified.

All as per item No 23 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified and as directed.

M&L 18 to 20mm thick granite stone (of any type ) work (table rubbed and polished) in Wash basin counter, cooking platform, window cill/jambs etc laid bedded over 15mm thick CM (1:4) bedding & pointed in white/coloured cement to match coloured tiles including cutting to desired shape as reqd, Rounding, grinding and mirror polishing complete. (Note : Colour of granite shall be as approved by Engr-In-Charge)

S&F for Powder coated Aluminium snap grid frame work for ceiling 605mm x 605mm using aluminium anodised sections main tee 36.5X25X1.4mm, cross 23.5X26.4X1.4mm, angle 25X25x1.4mm including cutting, drilling jointing etc complete including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good etc complete all as specified and as directed.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for Powder coated Aluminium grill (minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in charge.

M&L for 12mm thick Prelaminated particle board, exterior grade with decorative choice lamination on both sides as in Doors, Cub boards, cabinet, shelves etc and in simillar works, fixed with screws as reqd etc all as specified and as dierected.

S&F for plain sheet glass 5.5 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane etc all as specified.

S&F for Aluminium alloy wire cloth 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.

S&F 300mm long Aluminum alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded section or cast aluminum alloy etc complete all as specified and as directed.

S&F 150mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor etc complete all as specified and as directed.

S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall or in floors or in trenches etc using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F for 110mm dia PVC (SWR) bends any radius complete all as specified and as directed.

S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws as specified.

S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws complete all as specified and as directed.

S&F rolled sections as in post built up of one beam / channel or angle section with flanged plates, caps bases slices angle brackets cleats and other connections, conforming to Fe 410-w.(Gde-E-250 ) quality-A complete all as specified and as directed.

S&F for Roof trusses (framed), trussed, purlins, and fastening and heavy brackets framing (beam, tee, angle, channel or flats section) including distance pieces, cleat etc conforming to Fe-410 (Gde-E250) quality -A complete all as specified and as directed.

S&F for mild steel plates (plain or chequired) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde E-250) Quality -A complete all as specified and as directed.

M&L for Aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0micron fixed over frame of aluminium tabular section 50x25mmx 2.0mm thick, having panels not exc 1200x1200mm with necessary silicon filling, in approved pattern as in column, beam, wall at any height with necessary scafoldings etc complete as specified and as directed.

S&F for Neon light letters/symbols of height upto 45cm and depth 25mm (size and shape as required in sign boards) using acrylic sheet with suitable adopters and required wiring with connected accesories reqd for functioning and fitting the same with necessary stainless steel nuts and bolts as per site requirements etc complete all as specified

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for Aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering etc fixed with self tapping screws as complete all as specified and as directed.

M&L for HDF boards (fire & water proof) of 19mm thick as in cub boards, cabinet, shelves etc & the like with decorative choice laminations on one side and balancing white laminations on other side etc complete all as specified and as directed.

S&F 100mm SS Auto concealed hinges (full overlay) suitable for kitchen cabinets, cub boards, Shelves etc complete all as specified and as directed.

S&F SS Fancy type 'D' Type Drawer / Cabinet handles of Size 100mm, etc all as specified and as directed.

S&F SS Fancy type Marble Tower Bolt suitable for Drawer / Cabinet of Size 100mm, etc all as specified and as directed.

S&F Magnetic catcher with plate, glossy finish for Drawer / Cabinet of Size not less than 50mm, etc all as specified and as dierected.

Dismantling floor, hearth or wall tiling including CM bedding, removing rubbish off the premises complete all as specified and as directed.

M&L PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) 25mm thick as in levelling course, sub-floors and paving etc complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) bedding complete all as specified

M&L for glazed ceramic designed coloured tiles as in vertical surfaces of size 300x450x7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed incl 10 mm thick backing coat in CM (1:3) complete all as specified.

Taking up or down 20mm dia steel tubing connection, including cleaning for refixing or removal to store

S&F for 20mm bore unplasticised PVC pipe of pressure ratings 10kgf/Sqcn including all fittings fixed complete to walls, ceiling or in floor etc

S&F in repairs to CP Bib taps 15mm dia long body with flange cast copper alloy fancy type with crutch or capstan head handle screwed down for Iron pipe and fixed etc complete all as specified and directed.

M&L in repairs to PVC (SWR) multi floor trap 75mm with grating including jointing with solvent cement complete all as specified.

S&F for Brass chromium plated towel rail, 20mm dia D-type, 60cm long between flanges etc complete all as specified.

S&F in repairs to concealed stop valves 15 mm dia cast copper alloy fancy type CP with long shank and cup and crutch or capstan headscrewed down high pressure screwed both ends for iron pipe or for unions, etc complete all as specified and directed by Engr -in- charge.

S&F for ABS chromium plated shower rose long arm with or without swivel joint any size including fixing to steel pipe or union, of size 125mm etc complete all as specified and directed by Engr -in- charge.

Taking down chowkhats or pvc door frames with shutters without taking off shutters from frame n exe 1.5 sqm each complete all as specified.

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification complete all as specified and as directed.

S&F Factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement all as per specification.

S&F Aluminum anodized barrel bolt of extruded section 150mm long etc complete all as specified.

S&F extruded aluminum alloy handle fabricated type anodized 150 mm long etc complete all as specified.

S&F 100 mm long butt hinges, extruded aluminum alloy with galvanized mild steel hinge pin, anodized , type B-21 etc complete all as specified.

Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level and debris off the premises etc complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and below 15cm average depth and getting out in hard/dense soil etc all as specified and as directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded aggregates) as in sub base 100mm thick complete all as specified and as directed.

S&F for chequered cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6) etc all as specified and as directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M & L point wiring complete with 1100 volts grade, 1.5 sq.mm (nominal area), single core, FRLS PVC insulated ,unsheathed, multi stranded copper conductor cable drawn through and including medium grade, rigid , non-metallic PVC concealed/ surface conduit of size not less than 20 mm dia, with all necessary fittings, concealed in walls /roof/ floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth duly including suitable size of factory made fabricated MS sheet modular terminal box, flush mounting in the wall for mounting switches/switch socket combinations/ fan regulators etc., covered with suitable size of modular cover plates complete in making good the existing surface with existing colour coding as required at site complete all as specified for the following :-

All as per item No 73 above but for One light/fan point controlled by one modular switch 6 Amps one way.

Description same as per Srl item No 73 above but two light points controlled by one switch 6 Amps one way.

All as per item No 73 above but for one modular 3 pin 6 Amp socket out let on independent board.

All as per item No 73 above but for one modular 3 pin 6 Amps switch socket on same Board .

All as per item No 73 above but for one bell point controlled by one modular bell push switch 6 Amps one way.

All as per item No.73 above but point wiring with two single core 4.0 sqmm size cables and one 4.0 sqmm green colour cable as earth continuity conductor for one 6 pin 16 Amps socket out let on independent board.

S & F for switch modular type, 6 Amps 1 module, 230 volts AC circuit complete all as specified and directed.

S & F for socket outlet modular type 1 way 6 Amps, 3 pin, 230 volts AC circuit complete all as specified and directed.

S & F Socket outlet 2 in 1 modular type, 3 pin, 6 and 16, universal complete all as specified and directed.

S & F Switch modular type , single pole one way 16 amps complete all as specified and directed.

S & F modular bell push 5Amps flush type 230v, 50Hz AC complete all as specified and directed.

S&F, Electric Bell, Ding dong type working on 230 volts AC supply complete all as specified and directed.

Supply and fixing of Decorative ultra slim linear LED lighting fixture of 15 Watt recess mounted 220V , 50Hz with Aluminium housing ,environmental friendly energy efficient fitting recess mounted round/square in shape (Warm white/ white colour as per requirement of site complete) of light as required at site) complete all as specified and directed. Make - Philips Cat Part No : Dura Slim or equivalent make in CG/Havels. NOTE: The rate quoted deemed to include for any alterations required to existing false ceiling as per site condition for fixing light fitting.

Decscription all as otem No 86 above but 18 watt.

Supplying, fixing and testing Tube light fittings aluminium housing, Diffuser slim Integrated design LED 21 watts 4 feet, IP-20 including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Philips Cat Part No : BN021C LED22S or equivalent to CG/ Havells/ Luker

Supplying, fixing and testing Tube light fittings aluminium housing, Diffuser slim Integrated design LED 10 watts 2 feet, IP-20 including all accessories and fixing arrangements for fixing the light fitting complete all as specified and directed. Make: Philips Cat Part No : BN021C LED12S or equivalent to CG/ Havells/ Luker

Supply and fixing and testing LED Picture light fitting of cap 12 watt , bronzne , Aluminium materials , size - 500 x 80 x 95 , 420lm , 3000k with all fixing arrangements all as specified and directed. Make-Havells cat no LHLDESAARANC020 or equivalent to Philips/ CG

S & F Sub main wiring with PVC insulated FRLS cable 2 single core 4 sq mm 1100 V grade with stranded copper conductor cable using proper colour coding Phase Red /Yellow /Blue, Neutral- black and earth- green in and incl rigid PVC concealed conduit (ISI marked) incl all specials/ accessories etc and provision of PVC insulated FRLS copper conductor single core 4.0 sq mm for earth continuity all as directed. Note : 3 length of cable and one length PVC Conduit shall be measured and paid for one length.

Supply, laying, testing and commissioning of underground LT XLPE insulated, armoured heavy duty electric aluminium conductor cable 1100 Volts grade of cross section 2 x 10 sqmm (laid in terenches,ducts,pole,wall etc.) incl taking down old unsv cable all as specified and directed.

Supply & laying trenches or in cable ducts or clamping on wall DWC HDPE pipe of size 40mm (OD) x 32mm (ID) alongwith connected accessories like couplers, bends, end caps etc for LT cable protection all as specified and directed

All as per item Sl No 91 above but sub main wiring with 2 single core 6.0 sqmm duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire. Note for item No 91 & 94 : 3 length of cable and one length PVC Conduit shall be measured and paid for one length.

S & F SPN DB sheet metal enclosure double door suitable (IP-43) Protection 12 Way with 200 Amp rated standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete.

Decscription all as item No 95 above but 8 way.

Supply & fixing MCB SPN 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed .

Supply & fixing MCB single pole, 6 to 32 Amps (`C’ series) having current rating 10 KA complete all as specified and directed. Note for item No 95 to 98:- All copper conductors should be connected with MCB alongwith copper reducer terminals of suitable size duly crimpled.”

Please Enable Macros to View BoQ information